Cisco 1921 - how to configure VPN multiple Tunnels to AWS

Similar Questions

• ASA 5510 VPN multiple tunnels through different interfaces

  Is it possible to create VPN tunnels on more than one interface to an ASA (specifically 5510 with 8.4), or I'm doing the impossible?

  We have 2 public interfaces on our ASA connected to 2 different suppliers.

  We must work L2L tunnels of the SAA for remote offices through the interface that is our ISP 'primary' and also used as our default gateway for internet traffic.

  We are trying to install a remote office use our secondary connection for its tunnel (office of high traffic we would prefer separate away from the rest of our internet and VPN traffic).

  I can create the tunnel with the ACL appropriate for traffic tunnel, card crypto, etc., put in place a static route to force ASA to use the secondary interface for traffic destined for the public of the remote gateway IP address, and when I finished, traffic initiated by the remote site will cause the tunnel to negotiate and find - I can see the tunnel in Show crypto ikev1 his as L2L answering machine MM_ACTIVE , Show ipsec his with the right destination and correct traffic local or remote identities for interesting, but the ASA local never tries to send traffic through the tunnel.  If I use tracers of package, it never shows a VPN that is involved in the trafficking of the headquarters in the remote desktop, as if the SAA is not seeing this as for the corresponding VPN tunnel traffic.

  If I take the exact same access and crypo card statements list and change them to use the primary ISP connection (and, of course, change the remote desktop IP connects to), then the connection works as expected.

  What Miss me?

  Here is a sample of the VPN configuration: (PUBLIC_B is our second ISP link, 192.168.0.0/23 is MainOffice 192.168.3.0/24 is FieldOffice)

  permit access list range 192.168.0.0 PUBLIC_B_map 255.255.254.0 192.168.3.0 255.255.255.0

  NAT (Inside, PUBLIC_B) static source MainOffice MainOffice static FieldOffice FieldOffice

  card crypto PUBLIC_B_map 10 corresponds to the address PUBLIC_B_map

  card crypto PUBLIC_B_map 10 set counterpart x.x.x.x

  card crypto PUBLIC_B_map 10 set transform-set ESP-3DES-SHA ikev1

  PUBLIC_B_map PUBLIC_B crypto map interface

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  IKEv1 pre-shared-key *.

  Route PUBLIC_B x.x.x.32 255.255.255.224 y.y.y.y 1

  If I take this same exact configuration and change it to use PUBLIC (our primary connection) instead of PUBLIC_B, remove the instruction PUBLIC_B route and change the desktop to point to the ip address of the PUBLIC, then everything works, so my access list and crypto map statements must be correct.

  What I don't understand is why the ASA Head Office does not seem to recognize interesting for the tunnel traffic when the tunnel is for the second ISP connection, but works when it is intended for the main ISP.  There is no problem of connectivity with the ISP Internet B - as mentioned previously, the tunnel will come and negotiate properly when traffic is started from the desktop, but the traffic of main office is never sent to the bottom of the tunnel - it's as if the ASA does not think that traffic of 192.168.0.x to 192.168.3.x should pass through the VPN.

  Any ideas?

  Hello

  I think your problem is that there is no route for the actual remote network behind the VPN L2L through ISP B connection

  You could try adding add the following configuration

  card crypto PUBLIC_B_map 10 the value reverse-road

  This should automatically add a static route for all remote networks that are configured in the ACL Crypto, through the interface/link-ISP B.

  If this does not work, you can try to manually add a static route to the ISP B link/interface for all remote networks VPN L2L in question, and then try again.

  The route to the remote VPN peer through the ISP B does not to my knowledge.

  I would like to know if it works for you.

  It may be useful

  -Jouni

• How to configure VPN remote access to use a specific Interface and the road

  I add a second external connection to an existing system on a 5510 ASA ASA V8.2 with 6.4 AMPS

  I added the new WAN using another interface (newwan).

  The intention is to bring more internet traffic on the new road/interface (newwan), but keep our existing VPN using the old interface (outside).

  I used the ASDM GUI to make changes and most of it works.

  That is to say. The default route goes via (newwan)

  Coming out of a VPN using a site to character the way previous (out) as they now have static routes to achieve this.

  The only problem is that remote incomming VPN access Anyconnect do not work.

  I put the default static route to use the new interface (newwan) and the default tunnel road be (outside), but that's the point is will not...

  I can either ping external IP address from an external location.

  It seems that the external interface doesn't send traffic to the - external interface (or at least that's where I think the problem lies). How can I force responses to remote VPN entering IPS unknown traffic to go back on the external interface?

  The only change I have to do to make it work again on the external interface is to make the default static route to use external interface. Calling all internet traffic to the (external connection) original

  Pointers appreciated.

  William

  William,

  As it is right now that you will not use the same interface you have road to terminate remote access unless you know their IP addresses by default.

  In one of the designs that I saw that we did something like that.

  (ISP cloud) - edge router - ASA.

  The edge router, you can make PAT within the interface for incoming traffic on port udp/500 and UDP/4500 (you may need to add exceptions to your L2L static) of the router. It's dirty, I would not say, it is recommended, but apparently it worked.

  On routers, this kind of situation is easily solved using VRF-lite with crypto.

  M.

• How to configure VPN 3000 Concentrator for remote access

  I have inherited a VPN concentrator and want to configure it to provide remote access to my internal laboratory network when I'm traveling.  Private interface is configured as 192.168.1.240/24.  Public interface is configured as one of my public IP addresses.  I have a public IP pool on the back side of a cable modem Roadrunner.  I created a pool of addresses for clients such as 192.168.1.200 by 192.168.1.205.  I created all group configurations, group and user base.

  In the IP Routing tab, I see a default route pointing to my IP address of public gateway - the IP address of my box of roadrunner cable modem gateway.

  Since my VPN client, I am able to connect to the VPN concentrator.  I get an address from the pool and check the details of the tunnel under the statistics section shows IP address correct pool for the customer and the correct public IP address of my VPN reorga

  Jeff,

  According to statistics, it seems that the client sends traffic to the hub, but his answer not get back.

  We need check the hub settings itself.

  I need check the hub settings and that it is a GUI based device so I can't even ask to see the technology and the only option available is to WebEx.

  You're ok with webex, pls lemme session comfortable time id and e-mail to send the invitation, it takes no more time and we will carry it out

  Thank you

  Ankur

• Please give index on configuring vpn site to site on 881 to ASA 5505 cisco router

  Earlier my boss asked me to prepare to implement the VPN site-to site on router Cisco 881 Integrated Services to ASA 5505 router, which is now running on the side of HQ. Someone please give me a hint. I am now learning the pdf file from Cisco that mention how to configure VPN site to site between 1812 Cisco IOS router and router of the ASA 5505 using ASDM V6.1 and SDM V2.5. Cannot find the book for the Cisco 881 device.

  Someone please please suggest me something as soon as POSSIBLE.

  Thank you

  CLI version:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00807ea936.shtml

  ASDM and SDM Version:

  http://www.Cisco.com/en/us/partner/products/ps5855/products_configuration_example09186a0080a9a7a3.shtml

• Cisco 1841 how vpn tunnels? default 100vpn?

  Hi everyone, I have read the previous posts and I read that the cisco 1841 can manage up to 100 default VPN tunnels.

  1. is this true?  (I enclose my worm of show)

  2. this version of IOS support SSL VPN tunnels as well?

  SH ver
  Cisco IOS Software, 1841 (C1841-ADVSECURITYK9-M), Version 12.4 (3i), VERSION of the SOFTWARE (fc2)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2007 by Cisco Systems, Inc.
  Updated Thursday 28 November 07 18:48 by stshen

  ROM: System Bootstrap, Version 12.4 (13r) T, RELEASE SOFTWARE (fc1)

  Uptime SPAREROUTER is 7 minutes
  System to regain the power ROM
  System image file is "flash: c1841-advsecurityk9 - mz.124 - 3i.bin".

  ... Output omitted

  Cisco 1841 (revision 7.0) with 234496 K/K 27648 bytes of memory.
  Card processor ID FTX1151Y0BQ
  2 FastEthernet interfaces
  1 module of virtual private network (VPN)
  Configuration of DRAM is 64 bits wide with disabled parity.
  191K bytes of NVRAM memory.
  62720K bytes of ATA CompactFlash (read/write)

  Configuration register is 0 x 2102

  SPAREROUTER #.

  Thank you

  Randall

  Hello

  I guess that means that the total number of vpn ipsec tunnels taken in charge by the router of SSL VPN AIM is 800.

  If you want only a SSL VPN without the AIM module can it be based on the license.

  Kind regards

  Anisha

  P.S.: Please mark this thread as answered if you feel that your query is resolved. Note the useful messages.

• Configuration of the Cisco ACS 5.3 AnyConnect VPN and management of a Cisco ASA 5500.

  We have configured a Cisco ASA 5505 as a VPN endpoint for one of our user groups.  It works, but it works too well.

  We have a group called XXX we need to have access to the Cisco AnyConnect Client.  We have selected this group of our Active Directory and added to our ACS configuration.  We've also added a group called YYY that will manage the ASA. However, this group has no need to access the VPN.

  We added XXX movies for the elements of the policy of access to the network-> authorization profiles.  We also have a profile of YYY.

  She continues to knock on our default Service rule that says allow all.

  We have also created a default network access rule. for this.

  I am at a loss.  I'm sure I missed a checkbox or something.

  Any help would be really appreciated.

  Dwane

  We use Protocol Management GANYMEDE ASA and Ray for VPN access?

  For administration, you must change the device by default admin access strategy and create a permission policy. Even by the way, you can change the network access by default for vpn access and create a respective policy for that too.

  On the SAA, you must configure Ganymede and Ray both as a server group.

  For the administration, you can set Ganymede as an external authentication under orders aaa Server

  AAA-server protocol Ganymede GANYMEDE +.

  Console HTTP authentication AAA GANYMEDE

  Console Telnet AAA authentication RADIUS LOCAL

  authentication AAA ssh console LOCAL GANYMEDE

  Console to enable AAA authentication RADIUS LOCAL

  For VPN, you must set the authentication radius under the tunnel-group.

  I hope this helps.

  Kind regards

  Jousset

  The rate of useful messages-

• How to configure ASA5520 of Checkpoint IPsec tunnel configuration

  Hi guys and under tension, a lot of it!

  I have a problem, I set up an IPsec tunnel between my ASA5520 at a Checkpoint Firewall (PE) CONFIG below (not true FT)

  network of the ASA_MAPPED object

  4.4.4.0 subnet 255.255.255.0

  network of the CHECKPOINT_MAPPED object

  5.5.5.5.0 SUBNET 255.255.255.0

  OUT_CRYPTO extended access list permit ip object ASA_MAPPED object CHECKPOINT_MAPPED

  Crypto ipsec transform-set ikev1 CHECKPOINT_SET aes - esp esp-sha-hmac

  destination NAT (INSIDE, OUTSIDE) static source ALLNETWORKS(10.0.0.0/16) ASA_MAPPED CHECKPOINT_MAPPED of CHECKPOINT_MAPPED static

  NAT (INSIDE, OUTSIDE) source of destination ALLNETWORKS(10.0.0.0/16) static ASA_MAPPED static 4.4.4.11 5.5.5.11

  card crypto OUTSIDE_MAP 5 corresponds to the address OUT_CRYPTO

  OUTSIDE_MAP 5 set crypto map peer X.X.X.X

  card crypto OUTSIDE_MAP 5 set transform-set CHECKPOINT_SET ikev1

  card crypto OUTSIDE_MAP 5 defined security-association life seconds 3600

  CHECKPOINT_MAP interface card crypto OUTSIDE

  tunnel-group X.X.X.X type ipsec-l2l

  tunnel-group ipsec-attributes X.X.X.X

  IKEv1 pre-shared-key 1234

  ISAKMP crypto 10 nat-traversal

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  preshared authentication

  aes encryption

  sha hash

  Group 5

  life 86400

  IPsec Tunnel is in place and I can access the server on the other side via the beach of NATTED, for example a server behind the checkpoint with the IP 10.90.55.11 is accessible behind the ASA as 4.4.4.11, the problem is that I have never worked on a Checkpoint Firewall and servers/Server 4.4.4.11 that I can't connect to my environment to that checkpoint is configured with a Tunnel interface that is also supposed to to make NAT because of the superimposition of networks, at one point, I added an access to an entire list and bidirectional routing has been reached, but I encountered a new problem, I could not overlook from my servers public became unaccessecable, since all traffic was encrypted and get dropped to VPN: ipsec-tunnel-flow... for now the Tunnel is up and I can access the server via NAT 4.4.4.11, but can't access my internal servers. What did I DO WRONG (also, I don't have access to the Checkpoint Firewall (PE)) how their installation would be or how it should be to allow bidirectional routing?

  ========================================================

  Tag crypto map: CHECKPOINT_MAP, seq num: 5, local addr: X.X.X.X

  Access extensive list ip 4.4.4.0 OUT_5_CRYPTO allow 255.255.255.0 5.5.5.0 255.255.255.0

  local ident (addr, mask, prot, port): (4.4.4.0/255.255.255.0/0/0)

  Remote ident (addr, mask, prot, port): (5.5.5.0/255.255.255.0/0/0)

  current_peer: X.X.X.X

  #pkts program: 3207, #pkts encrypt: 3207, #pkts digest: 3207

  #pkts decaps: 3417, #pkts decrypt: 3417, #pkts check: 3417

  compressed #pkts: 0, unzipped #pkts: 0

  #pkts uncompressed: 3207, model of #pkts failed: 0, #pkts Dang failed: 0

  success #frag before: 0, failures before #frag: 0, #fragments created: 0

  Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0

  #send errors: 0, #recv errors: 0

  local crypto endpt. : X.X.X.X/0, remote Start crypto. : X.X.X.X/0

  Path mtu 1500, fresh ipsec generals 74, media, mtu 1500

  current outbound SPI: 5254EDC6

  current inbound SPI: 36DAB960

  SAS of the esp on arrival:

  SPI: 0x36DAB960 (920303968)

  transform: aes - esp esp-sha-hmac no compression

  running parameters = {L2L, Tunnel}

  slot: 0, id_conn: 19099648, crypto-card: CHECKPOINT_MAP

  calendar of his: service life remaining (KB/s) key: (3914999/3537)

  Size IV: 16 bytes

  support for replay detection: Y

  Anti-replay bitmap:

  0 x 00000000 0x0000000F

  outgoing esp sas:

  SPI: 0x5254EDC6 (1381297606)

  transform: aes - esp esp-sha-hmac no compression

  running parameters = {L2L, Tunnel}

  slot: 0, id_conn: 19099648, crypto-card: CHECKPOINT_MAP

  calendar of his: service life remaining (KB/s) key: (3914999/3537)

  Size IV: 16 bytes

  support for replay detection: Y

  Anti-replay bitmap:

  0x00000000 0x00000001

  unless I include any any on my access-list and the problem with that is  that my Public servers then get encrypted from the OUTSIDE interface  unless you know of a way to bypass the VPN
  
  

  No, u certainly shouldn't allow 0.0.0.0 for proxy ACL. Again, your config is very good. In addition, package account, this show that traffic is going throug the tunnel in two ways:

  #pkts program: 3207

  #pkts decaps: 3417

  Also, looking at the meter, I can guess that some of the traffic comes from the other site, but does not return back (maybe that's where you can not connect from behing Checkpoint). If you say that 0.0.0.0 solved the problem, are there no other NAT rules for subnet behind ASA, so the server IP, for which you are trying to connect behind the checkpoint, translates into something else (not the beach, included in proxy ACL), when to come back?

• How can I configure VPN with XP? Is it necessary to use a third party software? It requires a static IP address? It is possible with a dynamic IP?

  I am interested in establishing a VPN for my computer.  I looked at some of the information to help Ms.  I'm missing something in the way of understanding how do or end the connection.

  You can configure VPN regardless of static or dynamic IP, both are possible. You can refer to:

  http://support.Microsoft.com/kb/314076

• Configuration Cisco 1921

  I am configuring a Cisco 1921 router to connect with my cable modem.  The router gets an IP address from the DHCP server and I can ping resources on the internet on the router.   The router distributes DHCP addresses to clients, but clients are unable to access the internet.  I'm missing something simple.  Here is my config:
  
  R1-1921 #sh run
  Building configuration...
  Current configuration: 6236 bytes
  !
  ! 19:11:22 EST configuration was last modified Thursday, November 5, 2015 by *.
  version 15.3
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  hostname R1-1921
  !
  boot-start-marker
  boot system flash: c1900-universalk9-mz. Spa. 153 - 3.M6.bin
  boot-end-marker
  !
  !
  logging buffered 51200 warnings
  enable secret 5 $1$ F3oi$ EtowSjpBITAVsWVxr4EDM.
  activate the password *.
  !
  No aaa new-model
  No process cpu extended history
  No pork process autoprofile cpu
  iomem 10 memory size
  clock timezone IS - 5 0
  clock to summer time EDT recurring
  !
  !
  !
  !
  DHCP excluded-address 192.168.1.1 IP 192.168.1.100
  DHCP excluded-address IP 192.168.1.201 192.168.1.254
  DHCP excluded-address 192.168.2.1 IP 192.168.2.100
  DHCP excluded-address 192.168.2.201 IP 192.168.2.254
  DHCP excluded-address IP 10.10.10.1 10.10.10.100
  DHCP excluded-address IP 10.10.10.201 10.10.10.254
  DHCP excluded-address IP 192.168.20.1 192.168.20.100
  DHCP excluded-address IP 192.168.20.201 192.168.20.254
  !
  IP dhcp pool vlan2_Home_DHCP
  network 192.168.2.0 255.255.255.0
  F104.0a0a.140b hexagonal option 43
  domain name *.
  Server DNS 8.8.8.8 8.8.4.4
  default router 192.168.2.254
  Rental 7
  !
  IP dhcp pool vlan10_Home_DHCP
  Network 10.10.0.0 255.255.0.0
  F104.0a0a.140b hexagonal option 43
  domain name *.
  default router 10.10.10.1
  Server DNS 8.8.8.8 8.8.4.4
  Rental 7
  !
  IP dhcp pool vlan20_Home_DHCP
  network 192.168.20.0 255.255.255.0
  F104.0a0a.140b hexagonal option 43
  domain name *.
  Server DNS 8.8.8.8 8.8.4.4
  default router 192.168.2.254
  Rental 7
  !
  IP dhcp pool vlan1_Home_DHCP
  network 192.168.1.0 255.255.255.0
  F104.0a0a.140b hexagonal option 43
  domain name *.
  Server DNS 8.8.8.8 8.8.4.4
  by default-router 192.168.1.254
  Rental 7
  !
  !
  !
  IP domain name *.
  IP cef
  No ipv6 cef
  !
  Authenticated MultiLink bundle-name Panel
  !
  !
  Crypto pki trustpoint TP-self-signed-2424561219
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 2424561219
  revocation checking no
  rsakeypair TP-self-signed-2424561219
  !
  !
  TP-self-signed-2424561219 crypto pki certificate chain
  certificate self-signed 01
  3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
  2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
  69666963 32343234 35363132 6174652D 3139301E 170 3135 31313032 31383034
  35395A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
  4F532D53 5369676E 656C662D 43 65727469 66696361 74652 32 34323435 65642D
  36313231 3930819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
  81008E99 C46CD1DA 4626A4A1 614268 HAS 4 FC70E1B0 66E4D691 6F1DDA9E EE15D3D6
  44469CAF D9EB6EAF B155D164 5E75CD1E B0541204 98C7BC8A E973A18A 852F7BC3
  09B33BDB C4C63C75 4C8B7A60 BA3BB4E7 C980BDFA 35F50803 C92973F4 19A 90217
  48E993E3 BFC1EE4D C9A8ABE7 C094E89B 9629195A 0763605 A D577278C B8C39AB9
  010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355 0CEF0203
  551 2304 18301680 14B9ECCC A5378EAC C33EA600 3A11948F 56021544 74301 06
  03551D0E 04160414 B9ECCCA5 378EACC3 3EA6003A 11948F56 02154474 300 D 0609
  2A 864886 05050003 81810046 FC666C70 E65C191B 951D69CC BE68D6D1 F70D0101
  B5EC7175 ED432B26 7C44E882 1 C 04F30A7C 006392 E782CB04 CC898FD4 2B5F9085
  A84DB5BA 0996408A 46D36AE7 20A4BADA D418EC0D F7A94E46 08782215 C7EEF16F
  998E78F0 17026E9A 0705D4F7 FCEEED19 AB467E35 6A8E2CED A35BD0C3 236CF87D
  76F3BF78 45D940EF DF0A8934 D411F3
  quit smoking
  
  udi pid CISCO1921/K9 sn license *.
  !
  !
  !
  redundancy
  !
  !
  !
  !
  !
  property intellectual ssh time 60
  !
  !
  !
  !
  !
  !
  !
  !
  !
  interface Loopback0
  172.40.59.1 the IP 255.255.255.255
  !
  the Embedded-Service-Engine0/0 interface
  no ip address
  Shutdown
  No cdp enable
  !
  interface GigabitEthernet0/0
  no ip address
  automatic duplex
  automatic speed
  No cdp enable
  No mop enabled
  !
  interface GigabitEthernet0/0.1
  encapsulation dot1Q 1 native
  IP 192.168.1.253 255.255.255.0
  No cdp enable
  !
  interface GigabitEthernet0/0.2
  encapsulation dot1Q 2
  192.168.2.253 IP address 255.255.255.0
  No cdp enable
  !
  interface GigabitEthernet0/0.10
  encapsulation dot1Q 10
  IP 10.10.10.1 255.255.0.0
  No cdp enable
  !
  interface GigabitEthernet0/0.20
  encapsulation dot1Q 20
  address 192.168.20.1 255.255.255.0
  No cdp enable
  !
  interface GigabitEthernet0/1
  DHCP IP address
  no ip redirection
  no ip proxy-arp
  NAT outside IP
  IP virtual-reassembly in
  automatic duplex
  automatic speed
  No cdp enable
  !
  IP forward-Protocol ND
  !
  no ip address of the http server
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  !
  IP nat inside source list 1 interface GigabitEthernet0/1 overload
  IP default-network 192.168.1.0
  IP route 0.0.0.0 0.0.0.0 dhcp 20
  !
  no routing capabilities-Manager service
  not run cdp
  !
  !
  access-list 1 permit 192.168.1.0 0.0.0.255
  access-list 2 allow to 192.168.10.0 0.0.0.255
  access-list 2 allow 192.168.20.0 0.0.0.255
  access-list 2 allow 192.168.30.0 0.0.0.255
  access-list 2 permit 192.168.40.0 0.0.0.255
  access-list 2 allow to 192.168.1.0 0.0.0.255
  access-list 2 allow 10.10.20.0 0.0.0.255
  access-list 3 Let 192.168.10.0 0.0.0.255
  access-list 3 allow 192.168.20.0 0.0.0.255
  access-list 3 allow 192.168.30.0 0.0.0.255
  access-list 3 permit 192.168.40.0 0.0.0.255
  access-list 3 Let 192.168.1.0 0.0.0.255
  access-list 23 allow 10.10.10.0 0.0.0.7
  !
  control plan
  !
  !
  !
  Line con 0
  exec-timeout 0 0
  local connection
  line to 0
  line 2
  no activation-character
  No exec
  preferred no transport
  transport output pad rlogin lapb - your MOP v120 udptn ssh telnet
  StopBits 1
  line vty 0 4
  privilege level 15
  local connection
  transport of entry all
  line vty 5 15
  privilege level 15
  local connection
  transport of entry all
  !
  Scheduler allocate 20000 1000
  !
  end

  Your modem might need routes to subnets and the NAT configuration for these subnets.

  However, another way to do it is NAT CBC all IP addresses to the IP of the interface gi0/1 looks you can try to do.

  If you don't then.

  (1) you must add 'ip nat inside' to every subinterface

  (2) the ACL for your NAT made reference only 192.168.1.x customers while your other ACL refers all subnets.

  If you want to have all subnets access the internet turn it into NAT reference one another ACLs

  (3) don't know what you're doing with the statement "ip default-network 192.168.1.0.

  Just remove it and use the default route you have in your configuration and you don't need to add an ad at the end.

  Jon

• LT2P configuration vpn cisco asa with the internet machine windows/mac issue

  Dear all,

  I have properly configured configuration vpn L2TP on asa 5510 with 8.0 (4) version of IOS.

  My internet does not work when I connect using the vpn. Even if I give power of attorney or dns or I remove the proxy

  It does not work. only the resources behind the firewall, I can access. I use the extended access list

  I tried also with the standard access list.

  Please please suggest what error might be.

  Thank you

  JV

  Split for L2TP over IPSec tunnel tunnel is not configured on the head end (ASA), it must be configured on the client itself, in accordance with the following Microsoft article:

  http://TechNet.Microsoft.com/en-us/library/bb878117.aspx

• How to configure a VM with multiple network cards to see Agent?

  How to configure a VM with multiple network cards to see Agent?

  We can archive this requirement by configuring the subnet used view Agent.

  The subnet determines which view address of Network Agent provides the server instance to connect to view for the client protocol connections. The view on VM officer has more than one NIC

  Follow the procedure below:

  on a display Agent installed VM,

  * Recording of VM session.

  * RUN--> type regedit or type regedit.exe at the command prompt

  * Create a registry entry to configure the subnet.

  For example: is HKLM\Software\VMware, Inc. \VMware VDM\Node Manager\subnet = n.n.n.n/m type - REG_SZ.

  In this example, n.n.n.n is the TCP/IP subnet, and m is the number of bits in the subnet mask.

• How to configure ESS to the multiple proxy weblogic administration console

  Hello

  We use a 11.1.1.7 OSH and OAM webgate 11g and 11.1.2.

  To bring two weblogic server admin console in Kingdom of Single Sign-on.

  
  Please let us know how to configure ESS to the multiple proxy console weblogic.

  Thank you

  Stern John

  Activate the configuration of the virtual server on OSH and assign each administration console to another virtual server.

• How to configure Cisco Telepresence SX 20

  SX20.PNG

  

  Looking for this topology please help me how I can configure SX 20.

  If you do a search in these forums for autonomous SX20, you'll see a lot of messages that describe how to configure a SX20 and required firewall ports.

  A good example is this: autonomous SX20

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Cisco 1921 / K9

  Hi all

  1: my Corp Office, I installed a K9 Cisco 1921, I want to know that how IPSec VPN Tunnel Cisco 1921 /k9 can support and what is the IPSec VPN throughput?

  2: I have connected a link bandwidth (150 Mbit/s Download and 25 Mbit/s upload) to my Cisco 1921/K9, I want to know if Cisco 1921/K9 is able to manage bandwidth 150Mbps?

  3: If one of my retail site runs on 10 Mbps of bandwidth on Cisco RV220W connect to Cisco 1921/K9 for the Corp. Office. How much bandwidth IPSec tunnel will use?

  4: I have 200 points of sale and each have 5 computers, wifi and son (Mix few are on wifi and little are wired) that is block to install to the location of the retail of Cisco RV325 Cisco RV220W or 3.

  Thank you

  Sandy

  For retail locations, I would watch the series 880 s. They are available with built-in ADSL/VDSL modems and also wireless. The WIFI network can be controlled by a WLC.

  Management is the reason why I use RV-devices. As far as I know, they have still any IOS-like. The AP can be controlled with a WLC which also makes very easy to manage.

  For the router to 4000, I know that what is stated in the data sheet and the part of the config guide of license (the last router Cisco 4000 I used performed a decade... ;-)).

  But there are more feature-licenses like DRY/SSEC you need.

  It seems that the performance is entirely controlled by the license and the 100 / 300 Mbps is the performance of the services. But without the HSEC license, you are limited (as for many cisco routers) to 85 Mbps encrypted 225 tunnels and bandwidth.