Cisco and Checkpoint - no selected proposal
Hello
We had a working IPSEC VPN between router IOS and Checkpoint FW group. Now, after you add host entries in the ACL, we did get "no selected proposal.
My question:
=> Can we use more than an entry in an ACL, attached to a card encryption?<>
Like this for example:
access-list 125 allow ip 172.17.17.160 0.0.0.31 4.72.0.0 0.0.255.255
access-list 125 allow ip 172.17.18.0 0.0.0.31 4.72.0.0 0.0.255.255
access-list 125 allow ip 172.17.18.0 0.0.0.31 host 4.14.6.243
access-list 125 allow ip 172.17.18.0 0.0.0.31 host 4.50.50.4
access-list 125 allow ip 172.17.18.0 0.0.0.31 host 4.26.13.5
...
Hi Richi
Hi Richi,
Yes, you can use more than one ACL entry, but the ACL must be symmetric across the VPN.
Thus, for example
access-list 125 allow ip 172.17.18.0 0.0.0.31 host 4.26.13.5
should be on the other side:
access-list 125 permit host ip 4.26.13.5 172.17.18.0 0.0.0.31
Have you checked that you have symmetrical access lists?
It will be useful,
Paulo
Tags: Cisco Security
Similar Questions
-
Cisco and Checkpoint VPN clients on a single PC
Hello
I'm in the following fix:
I had used customer Checkpoint SecuRemote 4.1 SP - 5 VPN in the past.
Now, I have installed the Cisco VPN client version 4.0.4 on my PC to access IPSec VPN for the PIX in our headquarters.
According to Cisco VPN release notes http://www.cisco.com/univercd/cc/td/doc/product/vpn/client/rel404/404clnt.htm#wp1346340 , it should be possible to have clients both Cisco and Checkpoint VPN installed on the same machine.
But I am not able to connect to my PIX, I receive the following error message:
"Secure the complete VPN connection locally by the Client.
Reason 403: failed to contact the security gateway. »
When I'm looking for signs of PC control-> system-> hardware-> device Administration-> network cards, I can see Cisco Systems VPN Adapter disabled.
After you activate manually, I always get the same error when you try to connect to the Cisco VPN client.
After PC restart the Cisco VPN adapter is disabled later.
I tried to uncheck Check Point SecuRemote form my Dial-up connection (bypassing CSCea31192 of bug, but the bug does not affect NAT - T connection which I use).
I noticed the same situation on three different computers, one running Windows XP, both running Windows 2000.
After uninstalling the client Checkpoint completely (including Windows registry manual removal), the Cisco VPN client works very well.
It seems to me, therefore, that there is a profound mismatch between Cisco and Checkpoint VPN clients.
Does anyone know of a workaround?
Thank you
Milan
We had the same problem with some of our users who need to use the two clients to connect to customer sites.
If I remember the cisco client does not start automatically, but the client of checkpoint 4.1 don't.
We by-passed by deleting the registry entry point control that starts the client at startup. fwenc.exe is the entrance and it is in
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Run
After that make a shortcut to the executable file that is stored in the directory \bin to relevant checkpoint on the client (it is different from NT & 9 client x) and then only start when it is necessary.
Hope that's a help
-
Problem router Cisco and Checkpoint VPN
Hello
I couldn't establish vp from site to site between cisco and checkpoint. Can you please check the logs?
Thank you.
* 29 sept 08:17:22.627: IPSEC (sa_request):,.
(Eng. msg key.) Local OUTGOING = Y.Y.Y.Y:500, distance = X.X.X.X:500,
local_proxy = 192.168.222.0/255.255.255.0/256/0,
remote_proxy = 10.0.10.0/255.255.255.0/256/0,
Protocol = ESP, transform = esp - aes 256 esp-sha-hmac (Tunnel),
lifedur = 3600 s and KB 4608000,
SPI = 0 x 0 (0), id_conn = 0, keysize = 256, flags = 0 x 0
* 29 sep 08:17:22.631: ISAKMP: (0): profile of THE request is (NULL)
* 29 sep 08:17:22.631: ISAKMP: created a struct peer X.X.X.X, peer port 500
* 29 sep 08:17:22.631: ISAKMP: new created position = 0x88AD1AB0 peer_handle = 0 x 80000004
* 29 sep 08:17:22.631: ISAKMP: lock struct 0x88AD1AB0, refcount 1 to peer isakmp_initiator
* 29 sep 08:17:22.631: ISAKMP: 500 local port, remote port 500
* 29 sep 08:17:22.631: ISAKMP: set new node 0 to QM_IDLE
* 29 sep 08:17:22.631: ISAKMP: (0): insert his with his 88AF7D94 = success
* 29 sep 08:17:22.631: ISAKMP: (0): cannot start aggressive mode, try the main mode.
* 29 sep 08:17:22.631: ISAKMP: (0): pre-shared key found peer corresponding X.X.X.X
* 29 sep 08:17:22.631: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
* 29 sep 08:17:22.631: ISAKMP: (0): built the seller-07 ID NAT - t
* 29 sep 08:17:22.631: ISAKMP: (0): built of NAT - T of the seller-03 IDexit
Router (config) #n
* 29 sep 08:17:22.631: ISAKMP: (0): built the seller-02 ID NAT - t
* 08:17:22.631 Sept. 29: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
* 08:17:22.631 Sept. 29: ISAKMP: (0): former State = new State IKE_READY = IKE_I_MM1* 29 sep 08:17:22.631: ISAKMP: (0): Beginner Main Mode Exchange
* 29 sep 08:17:22.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:17:22.631 Sept. 29: ISAKMP: (0): a Packet.o IKE IPv4 send* 29 sep 08:17:32.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:17:32.631: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
* 29 sep 08:17:32.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:17:32.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:17:32.631 Sept. 29: ISAKMP: (0): sending of a CPVPN IKE IPvaccess lists* 29 sep 08:17:42.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:17:42.631: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
* 29 sep 08:17:42.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:17:42.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:17:42.631 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE...
* 29 sep 08:17:52.627: IPSEC (key_engine): request timer shot: count = 1,.
local (identity) = Y.Y.Y.Y:0, distance = X.X.X.X:0,
local_proxy = 192.168.222.0/255.255.255.0/256/0,
remote_proxy = 10.0.10.0/255.255.255.0/256/0
* 29 sept 08:17:52.627: IPSEC (sa_request):,.
(Eng. msg key.) Local OUTGOING = Y.Y.Y.Y:500, distance = X.X.X.X:500,
local_proxy = 192.168.222.0/255.255.255.0/256/0,
remote_proxy = 10.0.10.0/255.255.255.0/256/0,
Protocol = ESP, transform = esp - aes 256 esp-sha-hmac (Tunnel),
lifedur = 3600 s and KB 4608000,
SPI = 0 x 0 (0), id_conn = 0, keysize = 256, flags = 0 x 0
* 29 sep 08:17:52.627: ISAKMP: set new node 0 to QM_IDLE
* 29 sep 08:17:52.627: ISAKMP: (0): SA is still budding. Attached new request ipsec. (local Y.Y.Y.Y, distance X.X.X.X)
* 29 sep 08:17:52.627: ISAKMP: error during the processing of HIS application: failed to initialize SA
* 29 sep 08:17:52.627: ISAKMP: error while processing message KMI 0, error 2.
* 29 sep 08:17:52.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:17:52.631: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
* 29 sep 08:17:52.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:17:52.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:17:52.631 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
* 29 sep 08:18:02.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:18:02.631: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
* 29 sep 08:18:02.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:18:02.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:18:02.631 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
* 29 sep 08:18:12.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:18:12.631: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
* 29 sep 08:18:12.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:18:12.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:18:12.631 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
* 29 sep 08:18:22.627: IPSEC (key_engine): request timer shot: count = 2,.
local (identity) = Y.Y.Y.Y:0, distance = X.X.X.X:0,
local_proxy = 192.168.222.0/255.255.255.0/256/0,
remote_proxy = 10.0.10.0/255.255.255.0/256/0
* 29 sep 08:18:22.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:18:22.631: ISAKMP: (0): the peer is not paranoid KeepAlive.* 29 sep 08:18:22.631: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) MM_NO_STATE (peer X.X.X.X)
* 29 sep 08:18:22.631: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) MM_NO_STATE (peer X.X.X.X)
* 29 sep 08:18:22.631: ISAKMP: Unlocking counterpart struct 0x88AD1AB0 for isadb_mark_sa_deleted(), count 0
* 29 sep 08:18:22.631: ISAKMP: delete peer node by peer_reap for X.X.X.X: 88AD1AB0
* 29 sep 08:18:22.631: ISAKMP: (0): node-930113685 error suppression FALSE reason 'IKE deleted.
* 29 sep 08:18:22.631: ISAKMP: (0): error suppression node 661004686 FALSE reason 'IKE deleted.
* 08:18:22.631 Sept. 29: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
* 08:18:22.631 Sept. 29: ISAKMP: (0): former State = new State IKE_I_MM1 = IKE_DEST_SA* 29 sep 08:18:22.631: IPSEC (key_engine): had an event of the queue with 1 KMI message (s)
* 29 sept 08:18:27.559: IPSEC (sa_request):,.
(Eng. msg key.) Local OUTGOING = Y.Y.Y.Y:500, distance = X.X.X.X:500,
local_proxy = 192.168.222.0/255.255.255.0/256/0,
remote_proxy = 10.0.10.0/255.255.255.0/256/0,
Protocol = ESP, transform = esp - aes 256 esp-sha-hmac (Tunnel),
lifedur = 3600 s and KB 4608000,
SPI = 0 x 0 (0), id_conn = 0, keysize = 256, flags = 0 x 0
* 29 sep 08:18:27.559: ISAKMP: (0): profile of THE request is (NULL)
* 29 sep 08:18:27.559: ISAKMP: created a struct peer X.X.X.X, peer port 500
* 29 sep 08:18:27.559: ISAKMP: new created position = 0x85EDF1F0 peer_handle = 0 x 80000005
* 29 sep 08:18:27.559: ISAKMP: lock struct 0x85EDF1F0, refcount 1 to peer isakmp_initiator
* 29 sep 08:18:27.559: ISAKMP: 500 local port, remote port 500
* 29 sep 08:18:27.559: ISAKMP: set new node 0 to QM_IDLE
* 29 sep 08:18:27.559: ISAKMP: find a dup her to the tree during the isadb_insert his 88C1CE60 = call BVA
* 29 sep 08:18:27.559: ISAKMP: (0): cannot start aggressive mode, try the main mode.
* 29 sep 08:18:27.559: ISAKMP: (0): pre-shared key found peer corresponding X.X.X.X
* 29 sep 08:18:27.559: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
* 29 sep 08:18:27.559: ISAKMP: (0): built the seller-07 ID NAT - t
* 29 sep 08:18:27.559: ISAKMP: (0): built of NAT - T of the seller-03 ID
* 29 sep 08:18:27.559: ISAKMP: (0): built the seller-02 ID NAT - t
* 08:18:27.559 Sept. 29: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
* 08:18:27.559 Sept. 29: ISAKMP: (0): former State = new State IKE_READY = IKE_I_MM1* 29 sep 08:18:27.559: ISAKMP: (0): Beginner Main Mode Exchange
* 29 sep 08:18:27.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:18:27.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
* 29 sep 08:18:37.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:18:37.559: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
* 29 sep 08:18:37.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:18:37.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:18:37.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
* 29 sep 08:18:47.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:18:47.559: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
* 29 sep 08:18:47.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:18:47.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:18:47.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.* 29 sep 08:18:57.559: IPSEC (key_engine): request timer shot: count = 1,.
local (identity) = Y.Y.Y.Y:0, distance = X.X.X.X:0,
local_proxy = 192.168.222.0/255.255.255.0/256/0,
remote_proxy = 10.0.10.0/255.255.255.0/256/0
* 29 sept 08:18:57.559: IPSEC (sa_request):,.
(Eng. msg key.) Local OUTGOING = Y.Y.Y.Y:500, distance = X.X.X.X:500,
local_proxy = 192.168.222.0/255.255.255.0/256/0,
remote_proxy = 10.0.10.0/255.255.255.0/256/0,
Protocol = ESP, transform = esp - aes 256 esp-sha-hmac (Tunnel),
lifedur = 3600 s and KB 4608000,
SPI = 0 x 0 (0), id_conn = 0, keysize = 256, flags = 0 x 0
* 29 sep 08:18:57.559: ISAKMP: set new node 0 to QM_IDLE
* 29 sep 08:18:57.559: ISAKMP: (0): SA is still budding. Attached new request ipsec. (local Y.Y.Y.Y, distance X.X.X.X)
* 29 sep 08:18:57.559: ISAKMP: error during the processing of HIS application: failed to initialize SA
* 29 sep 08:18:57.559: ISAKMP: error while processing message KMI 0, error 2.
* 29 sep 08:18:57.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:18:57.559: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
* 29 sep 08:18:57.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:18:57.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
Router #.
Router #.
* 08:18:57.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
* 29 sep 08:19:07.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:19:07.559: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
* 29 sep 08:19:07.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:19:07.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:19:07.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
Router #.
Router #un all
All possible debugging has been disabledThe log shows main mode setup has failed. See if this helps: http://www.itcertnotes.com/2011/04/ipsec-stuck-in-mmsasetup-and-mmnostat...
-
No Ping response from Site to Site connection between 876 of Cisco and CheckPoint Firewall
Hello!
We try to create a Site-to-Site - connection IPSec between a Cisco 876 (local site) and a control-firewall station (remote site). Cisco 876 is not directly connected to the internet, but it is behind a router ADSL with port-forwarding, redirection of ports 500 and 4500. The configuration of the Cisco 876 running is attached to this thread. Unfortunately, I get no results when debugging the connection with the command "debug crypto isakmp" and "debug crypto ipsec".
From the point of view of Checkpoint firewall the connection seems to be implemented, but there is no response from ping.
The server in the local site to be achieved since the network behind the firewall Checkpoint has a routing entry "PEI route add [inside the ip-net Remote] 255.255.255.0 [inside the premises of intellectual property]" (see also annex current config name ip addresses).
Establishing a VPN Cisco Client connection to the same router Cisco 876 works very well.
Any help would be much appreciated!
Jakob J. Blaette
Hi Jakob,
Add my two cents here.
You should always verify that the following ports and Protocol are open:
1 - UDP port 500--> ISAKMP
2 - UDP port 4500--> NAT - T
3-protocol 50---> ESP
A LAN-to-LAN tunnel will never establish a TCP session, but it could use NAT - T (if behind a NAT). Remember that a single translation isn't a port forwarding, a LAN-to-LAN tunnel is not good unless you have a one-to-one translation of the NATted device, which I think, in your case the router is working.
HTH.
Portu.
Please note all useful messages and mark this message as a response.
-
Can't click and drag to select anything in the Apple Pages
I worked for hours on this unanswered anywhere on the internet.
I can't click and drag to select text in the Apple Pages. I can click and drag to select text in other applications on the same computer, but in the Pages, I can't click and drag. It will show the text highlight for a fraction of a second, and then it will disappear. I can't copy or cut, because it will not select it. If I select the text with clicking and then holding down the SHIFT key and then clicking on at the end of the text, he chooses for me. But clicking and slippery will only highlight, then disappear. What's wrong???
I have
- computer restarts
- restarted apple pages
- trashed plists iWork (cannot find a specific pages plist)
- Troubleshoot-made form another computer by comparing the preferences, settings, all on the same version of Pages
- sought objects to make them 'selectable' (there is no objects, and this happens on all documents, including new pages documents I just create and try to highlight a Word)
I'm on an iMac OSx 10.11.5 end 2013
Apple Pages 5.6.2 (2573)
It is a long-standing problem in OS X, are not specifically in any version of the Pages. Have you tried clicking & holding it down for a second or two in the text before you drag?
-
If I have several fields and if I select a field in a drop-down list it will fill the other fields
Thank you
Brain
Please post your question on InfoPath 2010 at the following link
-
Cannot open word document because a
"appropriate graphics importer is not found."
I had this problem and the technician "selected" Word as an opener, but I don't know where to find them on my computer. Can you direct me while I have when I want the word docuents to open they will be?
Right click on the saved file.
Select: Open with on the shortcut menu.
Click: Choose [default] program
Letter: Microsoft Word
Check: Always use the selected program to open this type of file.
Click OK.Bruce Hagen
MS - MVP October 1, 2004 ~ September 30, 2010
Imperial Beach, CA -
original title: Desktop sidebar gadgets
When you download a new gadget which folder does download while it appears in the selection of additional gadget. I can't find a record that relates to the sidebar or gadgets on my computer. Ran a search, and they do not always show upward. In addition, instructions to restore gadgets installed with the computer: do right click Select sidebar - select Properties - 'Restore gadgets installed with windows' this selection is gray and cannot be selected. What now?
Here are the steps to download and install new gadgets. http://freewindowsvistatutorials.com/meetWindowsVista/windowsSidebarAndGadgets/downloadAndInstallSidebarGadgets.htm. There is no particular place to download - usually, I download them to the desktop for installation and then I use C:\Users\
personal myself (with a special created Gadgets folder it contains) to store the download for use later, if necessary (assuming that I save it at all). Also, this procedure explains how to remove gadgets using the sidebar, so you don't have to go looking to uninstall files or anything like that. As far as the original gadgets go, here's a thread on the same problem with a solution which is marked as an answer (even if the person who has posted never confirmed it worked):http://social.answers.microsoft.com/Forums/en-US/vistaprograms/thread/1a979f08-a67e-43a6-a87c-3fa02dff9be1.
If this does not work, perhaps to restore the entire box will solve the problem. Here's how:http://support.microsoft.com/kb/963010. It can uninstall everything new gadgets that you added when it resets to zero (and I'm not positive that it will restore the original gadgets if he can fix the button greyed out), but if you accept that, it's worth a try.
I hope this helps.
Good luck!
Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
After leaving the screen saver, display shuts off and change to select the user account screen
I have a windows7 32 bit desktop. While everything works fine the problem is whenever I leave the keyboard and mouse intact even for one minute, the display turns off and change to select the screen of the user. 'Disable the display' and "put the computer to sleep" has been on 'never' and screen saver changed nothing but the problem still persists.
Please provide the solution
Hi Sam,
Sorry for the late reply.
I understand that when your computer is left idle, the select user screen appears.
The issue can be caused if the power plan settings are incorrect.
To get a better understanding of the issue, I want to know:
- What is the brand and model of your computer?
- You did it changes on your computer before this problem?
To resolve the problem, try the following methods:
Method 1: Troubleshooting to be able to run.
The resolution of the problems of power check things as settings timeout of your computer, which determines how long the computer waits before turning off the display or enter the mode 'sleep'. These settings can help you save energy and extend the life of the battery in your computer.
http://Windows.Microsoft.com/en-us/Windows7/open-the-power-Troubleshooter
After trying method 1, if the problem persists, try Method 2.
Note: When you're done, restart your computer and check if your computer works fine. If the problem persists, try Method 2.
Method 2: Change the screensaver settings.
I suggest you follow also the suggestion given in the answer by Vijay B answered the
May 14, 2013.
Please, try the above suggestions and we provide the information required so that we can help you.
-
Client VPN Cisco and Cisco Secure
Cisco VPN client and the VPN from Cisco Secure client free to use with pix firewall software?
Thank you.
Hello
If you have a valid contract to Cisco and you can get the following link:
http://www.Cisco.com/Kobayashi/SW-Center/SW-VPN.shtml
with your CCO login, then you should be able to use these customers at no cost because they are already covered by the contract.
Thank you and best regards,
Abdelouahed
-=-=-
-
I just changed a MS Word file that I sent to myself. Dialog box asks if you want to open or save. I chose open. I'm making updates and proceed to select save ICON (disk). I wanted to send the doc after update, but MSN does not allow to download an open file. I click save ICON new and closed the file, but when I looked for the file, it was not available. Y at - it a temporary area so that the file is saved.
If not, then a suggestion would be to give the user a prompt to remind them that the file was not registered although check-in ICON selected constantly throughout the writing of the document.
Thanks for your help.
If you have an attachment to the document that you want to edit, save the attachment to your HARD disk first and then change it. After starting change it, choose Save as and you keep moving, click on save or Ctrl + S to update the changes, once again this made, set the document.
Editing an attachment while remaining attached to an e-mail message will not save changes if there is an interruption such as you describe.
-
12.1.3 JDeveloper and table for selection of rows in Internet Explorer 9
Configuration: Windows 7, Internet Explorer 9 12.1.3, JDeveloper (sorry, the company standard for now)
I have problems of selection of rows in a table when you use IE9 (disabled compatibility view) as my browser. I created a simple application to test. I did the following:
1 created a new web application from merger in JDev 12.1.3.
2 objects of business created for 1 table
3. create a simple page (jspx) for testing
4 dropped the table on the side of Center of a PanelStretchLayout on the page as a table read-only with sorting and single-row selection enabled.
5. changed the property table DisplayRow selected. No other property has changed.
When I run the application, the table appears and is filled as expected. However, after you select at random the rows in the table, the application will lose focus and become hidden behind other applications on my desktop. If I bring the application in the foreground and try again the same thing will happen. After the selections of line 1 X application will disappear from the screen.
I decided to reproduce the JDev 12.1.2 test. In JDev 12.1.2 the application behaves as expected. Never, the application loses focus after several attempts to select a field.
I wonder if something in the hotfix released to correct the 12 c/Internet Explorer 11 questions is the culprit.
Everyone knows about this problem? I hope there is a change of ownership that I do in 12.1.3 to solve the problem.
Thanks in advance!
A solution that seems to work...
Add a clientListener inside the table
Add a javascript method
function handleTableSelection() { window.focus(); }
Just seems to bring the window to the front without changing anything, as far as I can tell.
-
There are two select statement, which are as follows: 1) select project id, the name of ppm.pm_projects project_name and request_id 2) select id, name from request_type_name to kcrt_request_details. There is a column called entity that can store a value i.e. project or request. I want to write a select statement containing a condition that is if the entity name is project and then run the select statement 1 otherwise, if the name of the entity's request, then run the select statement 2. All this must be written in a select statement. Can someone help me how to write this select statement type.
Hello
Hello
2726057 wrote:
... There is a column called entity that can store a value i.e. project or request. ...
In which table is this column? Assuming that it is in a table called entity_table, you can do something like this:
SELECT project AS id
project name AS the name
OF ppm.pm_projects
WHEN THERE IS)
SELECT 1
Of entity_table
Entity WHERE = "Project".
)
UNION ALL
SELECT request_id ID
request_type_name AS name
OF kcrt_request_details
WHEN THERE IS)
SELECT 1
Of entity_table
Entity WHERE = 'ask '.
)
;
This does not have anything on the number of lines is entity_table, or what are the values in the column of the entity. In other words, the query works in all cases. If any line in entity_table entity = 'Project', then the pm_projects data will be included in the result set. If any line in entity_table entity = 'Request', kcrt_request_details data will be included.
I hope that answers your question.
If this isn't the case, please post a small example data (CREATE TABLE and only relevant columns, INSERT statements) for all of the tables involved and the results desired from these data.
Explain, using specific examples, how you get these results from these data.
Always say what version of Oracle you are using (for example, 11.2.0.2.0).
See the FAQ forum: https://forums.oracle.com/message/9362002#9362002
-
All my pictures have disappeared? I work on a lot that I had downloaded, and then I selected, then went to create a new collection and baptized DH slideshow 2015, then press return and now it is gone! Help, please!
You have created a new CATALOG... ! not a collection! (looking at your screen-clip)
Re-open your correct catalogue-'Lightroom Catalog.lrcat 5' in the Menu > file > open recent element.
Select the pictures again, click [+] on the header of the COLLECTIONS Panel.
Before going further, learn from this video tutorial-
-
I managed to install and started to build my site, to discover my library of widgets, States and scrolling effects selections don't respond to clicking on them or open somehow. I need to reinstall and start over?
Are you referring to the widgets etc that you have added to pages or the actual interface of Muse?
If it's things on the page then you most likely have an empty element above them. Do a select on your page and make sure that there are no elements that overlap your clickable items. Also make sure your clickable items are highest in your layers panel.
Maybe you are looking for
-
Why my iMac does not automatically connect to my Airport time capsule.
Why is my iMac not automatically connected to my wireless after waking up, since I upgraded to OS Sierra?
-
Question about recovery on satellite disks series
Hello worldI had my equium for a week now and it already have mucked up. I managed to delete the partition hidden just reconfiguring the partitions on my HARD drive, is it possible to recover the hidden partition or that failing to get a set of recov
-
Computer won't start windows after SP2 updated which runs without error messages.
HelloI have problem with SP2 update. After correct installation the computer not boot to windows and the screen is black.I have toshiba A55 S326 all of origin, on which I replaced HD (now 250 GB) and RAM (1 GB now). In past I have updated the bios to
-
Update of MG7550 no link scanner after MacOS Sierra
I've updated to Sierra de MacOS a few days ago. Printing with my MG7550 works very well, but doesn´t work of scanning more. Error message is code: 15, 157, 0. I tried to reinstall the software, plugged into the power cables, but the problem persists.
-
make a toolbar to the language of bilangual (English-Persian) for windows XP
I tried to change the language of my new windows farsi, but can't do it. I try to make a toolbar(english-persian) of language bilangual for my pc at home. I've done it before in the Panel control, regional and language, choose farsi, then clicked on