Cisco router access outside the local network interface
Hi all!
I have Cisco router 892 (c890-universalk9 - mz.154 - 3.M4.bin) with firewall area and based on routing strategies.
Everything works fine, but now I need to have the ability to access external router interface IP LAN addresses.
For example, I PAT 192.168.4.1 port 8443 to the outside interface IP (93.93.93.2 for example) and I need to check LAN 93.93.93.2:8443.
! PAT:
IP nat inside source static tcp 192.168.4.1 8443 93.93.93.1 - extensible 8443 SDM_RMAP_1 road map
! DynNat to the internet:
IP nat inside source overload map route SDM_RMAP_1 interface GigabitEthernet0
! Routing policy
SDM_RMAP_1 allowed 10 route map
corresponds to the IP 101
match interface GigabitEthernet0! ACL 101 for routing policy
access-list 101 deny ip 192.168.3.0 0.0.0.255 192.168.111.0 0.0.0.255
access-list 101 deny ip 192.168.3.0 0.0.0.255 172.16.192.0 0.0.0.255
access-list 101 deny ip 192.168.3.0 0.0.0.255 172.16.177.0 0.0.0.255
access-list 101 deny ip 192.168.3.0 0.0.0.255 172.16.61.0 0.0.0.255
access-list 101 deny ip 192.168.3.0 0.0.0.255 172.17.19.0 0.0.0.255
access-list 101 deny ip 192.168.4.0 0.0.0.255 192.168.111.0 0.0.0.255
access-list 101 deny ip 192.168.3.0 0.0.0.255 host 172.16.194.100
access-list 101 deny ip 192.168.3.0 0.0.0.255 10.0.0.0 0.255.255.255
access-list 101 deny ip 192.168.4.0 0.0.0.255 10.0.0.0 0.255.255.255
access-list 101 deny ip 192.168.4.0 0.0.0.255 host 172.31.255.1
access-list 101 deny ip 192.168.4.0 0.0.0.255 host 172.16.194.100
access-list 101 permit ip 192.168.3.0 0.0.0.255 any
access-list 101 permit ip 192.168.4.0 0.0.0.255 any! ACL on the external interface:
plug-in software component gi0 extended IP access list
allow an ip
allow icmp a whole! External interface
interface GigabitEthernet0
Description $ETH - WAN$
IP 93.93.93.1 255.255.255.240
IP access-group gi0-in in
NAT outside IP
IP virtual-reassembly in
EXTENT of the Member's area network security
IP tcp adjust-mss 1452
automatic duplex
automatic speed
card crypto SDM_CMAP_2! Inside DMZ interface vlan:
interface Vlan4
IP 192.168.4.254 255.255.255.0
IP nat inside
IP virtual-reassembly in
security of the members of the DMZ
IP tcp adjust-mss 1452! Allow outbound traffic to DMZ to Internet:
Allow_All_ACL-DMZ extended IP access list
allow an esp
permit tcp host 192.168.4.1 host 192.168.111.2 eq 1521
refuse the 192.168.4.0 ip 0.0.0.255 192.168.111.0 0.0.0.255
refuse the 192.168.4.0 ip 0.0.0.255 172.17.19.0 0.0.0.255
allow icmp 192.168.4.0 0.0.0.255 any
ip licensing 192.168.4.0 0.0.0.255 any! Allow incoming traffic from the Internet to DMZ:
WAN_DMZ_ACL extended IP access list
allow tcp any a Workbench
permit tcp any any eq ftp
permit tcp any any eq 990
permit tcp everything any 51000 53000 Beach
permit tcp any any eq 995
permit tcp any any eq 465
permit tcp any any eq www
permit any any eq 443 tcp
allow icmp a whole
allow an esp
permit any any eq non500-isakmp udp
host ip 212.98.162.139 permit 192.168.4.0 0.0.0.255
IP 81.30.80.0 allow 0.0.0.255 any
IP 192.168.111.0 allow 0.0.0.255 192.168.4.0 0.0.0.255
IP 172.17.19.0 allow 0.0.0.255 192.168.4.0 0.0.0.255
host ip 172.16.194.100 permit 192.168.4.0 0.0.0.255
host ip 172.31.255.1 permit 192.168.4.0 0.0.0.255
permit ip host 172.31.255.1 172.17.193.100
refuse an entire ip! Focus on the area of firewall:
type of class-card inspect entire game DMZ_WAN_CLASS
match the group-access name DMZ Allow_All_ACLtype of class-card inspect entire game WAN_DMZ_CLASS
match the name of group-access WAN_DMZ_ACLtype of policy-card inspect DMZ_WAN_POLICY
class type inspect DMZ_WAN_CLASS
inspect
class class by default
droptype of policy-card inspect WAN_DMZ_POLICY
class type inspect WAN_DMZ_CLASS
inspect
class class by default
dropthe DMZ security
area WAN security
Security WAN_DMZ of the pair area source destination WAN DMZ
type of service-strategy inspect WAN_DMZ_POLICY
destination of DMZ_WAN source DMZ area pair WAN security
type of service-strategy inspect DMZ_WAN_POLICY
Maybe someone can help me to make Cisco to allow ports outside LAN using a NAT?
I did this on Mikrotik easily = |
It is due to the fact that they do not allow "hair pinning" by default, once this is configured, it will work.
Martin
Tags: Cisco Network
Similar Questions
-
WRT1900AC of external storage outside the Local network
I'm trying to set up my WRT1900AC router to access a USB attached as an external storage device. I can access the drive when I'm on the LAN, but I had no success accessing outside my local network. I enabled the FTP option in the section of external storage. With the FTP option is enabled, it then points me to the IP address that my cable modem ISP attributed to the router (192.168.0.2). Obviously this won't work from the outside world because it is not the IPV6 address. I install my modem cable to the port before 21-the 192.168.0.2 address and tried to access from outside by using my address IPV6 (ftp://77.XX.XXX.XX:21) but it will not connect. I was hoping someone could point me in the right direction, as I obviously don't do something here.
Hello, Steve99888. You must configure the settings of folder first. Check out this link.
-
5 view customer disconnects immediately outside the local network
I work with the 60 day trial of view 5.0 5.0 w/ESXi. Everything is configured and works well inside the LAN, but we have not been able to connect outside the local network. We have a single sign-on server that is associated with a single security server. All the rules of firewall, file server and configuration procedures correspond to installation and administration guides. Try to connect via PCoIP from a variety of devices.
The client connects, check credentials, allows you to choose a desktop, opens the window of the office, but him freezes and shut up saying: 'the connection to the remote computer is complete.' This happens every time.
Anny suggestions?
Hello
First of all, are you just a black screen that stays there for about 30 seconds then it closes with error? It is usually a problem with the connection to PCOIP. Could be firewall rules blocking a port, it could be the NATs. Security servers can be hard enough for the Setup program.
First check and see if you can connect by using the view client and RDP Protocol. Also, make sure that through the firewall, the Security Server can access the VLAN Office on tcp/udp 4172. Search for NATing in the external firewall and that your security server for installation of the connection to the server has the external IP address that there are listed (not the internal IP of the server security).
If you have a team network to talk to them and see if they can track packages. Look at the logs on the server and Security Office.
You don't have to worry about this error. Security Server does not need to be on the field, in fact it should not really be on the field. It somewhat defeats the purpose of having a security server. The client has authenticated the username and the password and is spent on the desktop then ok. If the Office is unable to connect the user for a reason, then they will be left on the desktop windows request a user name and a pass.
Hope this helps
Phil
-
Ipad Cisco ipsec VPN connects but not access to the local network
Hi guys,.
I am trying to connect our ipads to vpn to access network resources. IPSec cisco ipad connects but not lan access and cannot ping anything not even not the interfaces of the router.
If I configure the vpn from cisco on a laptop, it works perfectly, I can ping all and can access resources on the local network if my guess is that the traffic is not going in the tunnel vpn between ipad and desktop.
Cisco 877.
My config is attached.
Any ideas?
Thank you
Build-in iPad-client is not useful to your configuration.
You have three options:
(1) remove the ACL of your vpn group. Without split tunneling client will work.
2) migrate legacy config crypto-map style. Here, you can use split tunneling
3) migrate AnyConnect.
The root of the problem is that the iPad Gets the split tunneling-information. But instead of control with routing traffic should pass through the window / the tunnel and which traffic is allowed without the VPN of the iPad tries to build a set of SAs for each line in your split-tunnel-ACL. But with the model-virtual, SA only is allowed.
-
Cisco ASA 5505 remote VPN access to the local network
I have installed two ASA 5505 VPN site to site that works perfectly. Now, I also need to have 1 customer site to remote access VPN with Cisco VPN dialer. I can get the VPN dialer to connect the VPN and get a VPN IP address, but I do not have access to the remote network. can someone take a look and see what I'm missing? I have attached the ASA running config.
Apologize for the misunderstanding.
To access the remote vpn client 10.10.100.x subnet, the vpn-filter ACL is the opposite.
Please please share the following ACL:
FROM: / * Style Definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-marge-haut : 0 cm ; mso-para-marge-droit : 0 cm ; mso-para-marge-bas : 10.0pt ; mso-para-marge-gauche : 0 cm ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}
outside_cryptomapVPN list of allowed ip extended access any 10.10.20.0 255.255.255.224
TO:
/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-marge-haut : 0 cm ; mso-para-marge-droit : 0 cm ; mso-para-marge-bas : 10.0pt ; mso-para-marge-gauche : 0 cm ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}
outside_cryptomapVPN to access extended list ip 10.10.20.0 allow 255.255.255.224 all
Hope that helps.
-
Client remote access VPN gets connected without access to the local network
: Saved
:
ASA 1.0000 Version 2
!
hostname COL-ASA-01
domain dr.test.net
turn on i/RAo1iZPOnp/BK7 encrypted password
i/RAo1iZPOnp/BK7 encrypted passwd
names of
!
interface GigabitEthernet0/0
nameif outside
security-level 0
IP 172.32.0.11 255.255.255.0
!
interface GigabitEthernet0/1
nameif inside
security-level 100
IP 192.9.200.126 255.255.255.0
!
interface GigabitEthernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
nameif failover
security-level 0
192.168.168.1 IP address 255.255.255.0 watch 192.168.168.2
!
interface Management0/0
nameif management
security-level 0
192.168.2.11 IP address 255.255.255.0
!
passive FTP mode
DNS server-group DefaultDNS
domain dr.test.net
network of the RAVPN object
192.168.0.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.200.0_24 object
192.168.200.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.9.200.0_24 object
192.9.200.0 subnet 255.255.255.0
the inside_network object-group network
object-network 192.9.200.0 255.255.255.0
external network object-group
host of the object-Network 172.32.0.25
Standard access list RAVPN_splitTunnelAcl allow 192.9.200.0 255.255.255.0
access-list extended test123 permit ip host 192.168.200.1 192.9.200.190
access-list extended test123 permit ip host 192.9.200.190 192.168.200.1
access-list extended test123 allowed ip object NETWORK_OBJ_192.168.200.0_24 192.9.200.0 255.255.255.0
192.9.200.0 IP Access-list extended test123 255.255.255.0 allow object NETWORK_OBJ_192.9.200.0_24
pager lines 24
management of MTU 1500
Outside 1500 MTU
Within 1500 MTU
failover of MTU 1500
local pool RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 66114.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) source Dynamics one interface
NAT (it is, inside) static static source NETWORK_OBJ_192.9.200.0_24 destination NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.9.200.0_24
Route outside 0.0.0.0 0.0.0.0 172.32.0.2 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 outdoors
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint ASDM_TrustPoint0
Terminal registration
name of the object CN = KWI-COL-ASA - 01.dr.test .net, C = US, O = KWI
Configure CRL
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet 192.9.200.0 255.255.255.0 inside
Telnet timeout 30
SSH 0.0.0.0 0.0.0.0 management
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 66.35.45.128 255.255.255.192 outside
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 30
SSH version 2
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
internal RAVPN group policy
RAVPN group policy attributes
value of server WINS 192.9.200.164
value of 66.35.46.84 DNS server 66.35.47.12
VPN-filter value test123
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value test123
Dr.kligerweiss.NET value by default-field
username test encrypted password xxxxxxx
username admin password encrypted aaaaaaaaaaaa privilege 15
vpntest Delahaye of encrypted password username
type tunnel-group RAVPN remote access
attributes global-tunnel-group RAVPN
address RAVPN pool
Group Policy - by default-RAVPN
IPSec-attributes tunnel-group RAVPN
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory 2
Subscribe to alert-group configuration periodic monthly 2
daily periodic subscribe to alert-group telemetry
aes encryption password
Cryptochecksum:b001e526a239af2c73fa56f3ca7667ea
: end
COL-ASA-01 #.
Here is a shot made inside interface which can help as well, I've tried pointing the front door inside the interface on the target device, but I think it was a switch without ip route available on this subject I think which is always send package back to Cisco within the interface
Test of Cape COLLAR-ASA-01 # sho | in 192.168.200
25: 23:45:55.570618 192.168.200.1 > 192.9.200.190: icmp: echo request
29: 23:45:56.582794 192.168.200.1.137 > 192.9.200.164.137: udp 68
38: 23:45:58.081050 192.168.200.1.137 > 192.9.200.164.137: udp 68
56: 23:45:59.583176 192.168.200.1.137 > 192.9.200.164.137: udp 68
69: 23:46:00.573517 192.168.200.1 > 192.9.200.190: icmp: echo request
98: 23:46:05.578110 192.168.200.1 > 192.9.200.190: icmp: echo request
99: 23:46:05.590057 192.168.200.1.137 > 192.9.200.164.137: udp 68
108: 23:46:07.092310 192.168.200.1.137 > 192.9.200.164.137: udp 68
115: 23:46:08.592468 192.168.200.1.137 > 192.9.200.164.137: udp 68
116: 23:46:10.580795 192.168.200.1 > 192.9.200.190: icmp: echo request
COL-ASA-01 #.
Any help or pointers greatly appreciated, I have do this config after a long interval on Cisco of the last time I was working it was all PIX so just need to expert eyes to let me know if I'm missing something.
And yes I don't have a domestic network host to test against, all I have is a switch that cannot route and bridge default ip helps too...
Hello
The first thing you should do to avoid problems is to change the pool VPN to something else than the current LAN they are not really directly connected in the same network segment.
You can try the following changes
attributes global-tunnel-group RAVPN
No address RAVPN pool
no mask RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 ip local pool
local pool RAVPN 192.168.201.1 - 192.168.201.254 255.255.255.0 IP mask
attributes global-tunnel-group RAVPN
address RAVPN pool
no nat (it is, inside) static source NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 static destination NETWORK_OBJ_192.9.200.0_24 NETWORK_OBJ_192.9.200.0_24
In the above you first delete the VPN "tunnel-group" Pool and then delete and re-create the VPN pool with another network and then insert the same "tunnel-group". NEX will remove the current configuration of the NAT.
the object of the LAN network
192.168.200.0 subnet 255.255.255.0
network of the VPN-POOL object
192.168.201.0 subnet 255.255.255.0
NAT (inside, outside) 1 static source LAN LAN to static destination VPN-VPN-POOL
NAT configurations above adds the correct NAT0 configuration for the VPN Pool has changed. It also inserts the NAT rule to the Summit before the dynamic PAT rule you currently have. He is also one of the problems with the configurations that it replaces your current NAT configurations.
You have your dynamic PAT rule at the top of your NAT rules currently that is not a good idea. If you want to change to something else will not replace other NAT configurations in the future, you can make the following change.
No source (indoor, outdoor) nat Dynamics one interface
NAT source auto after (indoor, outdoor) dynamic one interface
NOTICE! PAT dynamic configuration change above temporarily interrupt all connections for users on the local network as you reconfigure the dynamic State PAT. So if you make this change, make sure you that its ok to still cause little reduced in the current internal users connections
Hope this helps
Let me know if it works for you
-Jouni
-
ASA5505 can transfer clients to remote VPN access to the local network
I have currently ASA 5505 and 2911-router and I am trying to configure the VPN topology.
Can ASA5505 you transmit to remote VPN access clients LAN operated by another router?
These two cases are possible? :
(1) ASA 5505 and 2911-router are separate WAN interfaces, each connected directly to the ISP. But so can I connect an other interfaces LAN of ASA 5505 in a switch managed by 2911 router customers to distance-SSL-VPN to inject into the local network managed by the router?
(2) ASA 5505 is behind router-2911. May 2911 router address public ip or public ip address VPN-access attempts have directly be sent to ASA 5505 when there is only a single public ip address address available?
Long put short, ASA 5505 can inject its clients to remote-access-VPN as one of the hosts on the local network managed by 2911-router?
Thank you.I could help you more if you can explain the purpose of this configuration and connectivity between the router and ASA.
You can activate the reverse route on the dynamic plane on the SAA. The ASA will install a static route to the customer on the routing table. You can use a routing protocol to redistribute static routes to your switch on the side of LAN of the SAA.
-
Need help about Remoteapp outside the local network (2008 R2 Std)
Hello
We have installed and configured all the 4 services (RDGM, RDLM, RDWA, RemoteApp Manager). Inside the lan, all published remote applications work correctly but
When accessing the log on credentials wan are invited on several occasions.
We use a self-signed certificate created by the remote application server. We have installed the certificate in the certification of approved root authorities store.
Question-is it possible to access remote app on the wan via this free sign certificate or we need to purchase a SSL certificate?
Thank you
Laros
This issue is beyond the scope of this site and must be placed on Technet or MSDN -
Remote VPN with PIX without access to the local network
Hi @all,
I ve running into problems and I have not found any solution. Can someone check my config?
Facts:
PIX 501 6.3 (3)
4.04 VPN client
Wanted solution: access to HO via VPN
VPN tunnel will be established, I get an IP address, but I can´t the systems behind the pix and the pix of access itself.
To the VPN Client Staticts, I see outgoing packets, but no entrant (if I send a ping to peer behind the pix)
I hope someone can help me
Attached is my config:
PIX 501 and 506/506e pix are not supported in v7 due to the fact that the cpu is not able to deal with the extended features of v7.
PIX 520 is not supported I guess it's because of the fact that the model is discontinued.
-
ASA 5505 VPN remote cannot access with my local network
Hello guys, I have a problem with my asa 5505 remote VPN access to the local network, the VPn connection works well and connected, but the problem is that I can't reach my inside connection network of 192.168.30.x, here's my setup, please can you help me
ASA Version 8.2 (1)
!
!
interface Vlan1
nameif inside
security-level 100
192.168.30.1 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 155.155.155.10 255.255.255.0
!
interface Vlan5
No nameif
no level of security
no ip address
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
inside_nat0_outbound list of allowed ip extended access any 192.168.100.0 255.255.255.240
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
IP local pool vpn-pool 192.168.100.1 - 192.168.100.10 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
Mull strategy of Group internal
attributes of the Group mull strategy
Protocol-tunnel-VPN IPSec
username privilege 0 encrypted password eKJj9owsQwAIk6Cw xxx
VPN-group-policy Mull
type mull tunnel-group remote access
tunnel-group mull General attributes
address vpn-pool pool
Group Policy - by default-mull
Mull group tunnel ipsec-attributes
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
context of prompt hostname
Yes, you will need to either configure split tunnel so that internet traffic goes out through your local Internet service provider, GOLD / directed by configuration current you are tunneling all traffic (internet traffic Inc.) to the ASA, then you will need to create NAT for internet traffic.
To set up a tunnel from split:
split-acl access-list allowed 192.168.30.0 255.255.255.0
attributes of the Group mull strategy
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split-acl
I hope this helps.
-
remote VPN and vpn site to site vpn remote users unable to access the local network
As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config
The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.
ASA Version 8.2 (2)
!
host name
domain kunchevrolet
activate r8xwsBuKsSP7kABz encrypted password
r8xwsBuKsSP7kABz encrypted passwd
names of
!
interface Ethernet0/0
nameif outside
security-level 0
PPPoE client vpdn group dataone
IP address pppoe
!
interface Ethernet0/1
nameif inside
security-level 50
IP 192.168.215.2 255.255.255.0
!
interface Ethernet0/2
nameif Internet
security-level 0
IP address dhcp setroute
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
passive FTP mode
clock timezone IST 5 30
DNS server-group DefaultDNS
domain kunchevrolet
permit same-security-traffic intra-interface
object-group network GM-DC-VPN-Gateway
object-group, net-LAN
access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
MTU 1500 Internet
IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
enable ASDM history
ARP timeout 14400
NAT-control
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
AAA authentication enable LOCAL console
LOCAL AAA authentication serial console
Enable http server
x.x.x.x 255.255.255.252 out http
http 192.168.215.0 255.255.255.252 inside
http 192.168.215.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dynmap 65500 transform-set RIGHT
card crypto 10 VPN ipsec-isakmp dynamic dynmap
card crypto VPN outside interface
card crypto 10 ASA-01 set peer 221.135.138.130
card crypto 10 ASA - 01 the transform-set RIGHT value
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
the Encryption
sha hash
Group 2
lifetime 28800
Telnet 192.168.215.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
management-access inside
VPDN group dataone request dialout pppoe
VPDN group dataone localname bb4027654187_scdrid
VPDN group dataone ppp authentication chap
VPDN username bb4027654187_scdrid password * local store
interface for identifying DHCP-client Internet customer
dhcpd dns 218.248.255.141 218.248.245.1
!
dhcpd address 192.168.215.11 - 192.168.215.254 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Des-sha1 encryption SSL
WebVPN
allow outside
tunnel-group-list activate
internal kun group policy
kun group policy attributes
VPN - connections 8
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
kunchevrolet value by default-field
test P4ttSyrm33SV8TYp encrypted password username
username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
username kunauto attributes
Strategy Group-VPN-kun
Protocol-tunnel-VPN IPSec
tunnel-group vpngroup type remote access
tunnel-group vpngroup General attributes
address pool VPN_Users
Group Policy - by default-kun
tunnel-group vpngroup webvpn-attributes
the vpngroup group alias activation
vpngroup group tunnel ipsec-attributes
pre-shared key *.
type tunnel-group test remote access
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
: end
kunauto #.Hello
Looking at the configuration, there is an access list this nat exemption: -.
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
But it is not applied in the States of nat.
Send the following command to the nat exemption to apply: -.
NAT (inside) 0 access-list sheep
Kind regards
Dinesh Moudgil
P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community
-
ASA 5505 IPSEC VPN connected but cannot access the local network
ASA: 8.2.5
ASDM: 6.4.5
LAN: 10.1.0.0/22
Pool VPN: 172.16.10.0/24
Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.
I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.
Here is my setup, wrong set up anything?
ASA Version 8.2 (5)
!
hostname asatest
domain XXX.com
activate 8Fw1QFqthX2n4uD3 encrypted password
g9NiG6oUPjkYrHNt encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 10.1.1.253 255.255.252.0
!
interface Vlan2
nameif outside
security-level 0
address IP XXX.XXX.XXX.XXX 255.255.255.240
!
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS server-group DefaultDNS
domain vff.com
vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0
access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
logging trap warnings
asdm of logging of information
logging - the id of the device hostname
host of logging inside the 10.1.1.230
Within 1500 MTU
Outside 1500 MTU
IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol nt AD
AAA-server host 10.1.1.108 AD (inside)
NT-auth-domain controller 10.1.1.108
Enable http server
http 10.1.0.0 255.255.252.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 10.1.0.0 255.255.252.0 inside
SSH timeout 20
Console timeout 0
dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal group vpntest strategy
Group vpntest policy attributes
value of 10.1.1.108 WINS server
Server DNS 10.1.1.108 value
Protocol-tunnel-VPN IPSec l2tp ipsec
disable the password-storage
disable the IP-comp
Re-xauth disable
disable the PFS
IPSec-udp disable
IPSec-udp-port 10000
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpntest_splitTunnelAcl
value by default-domain XXX.com
disable the split-tunnel-all dns
Dungeon-client-config backup servers
the address value vpnpool pools
admin WeiepwREwT66BhE9 encrypted privilege 15 password username
username user5 encrypted password privilege 5 yIWniWfceAUz1sUb
the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username
tunnel-group vpntest type remote access
tunnel-group vpntest General attributes
address vpnpool pool
authentication-server-group AD
authentication-server-group (inside) AD
Group Policy - by default-vpntest
band-Kingdom
vpntest group tunnel ipsec-attributes
pre-shared-key BEKey123456
NOCHECK Peer-id-validate
!
!
privilege level 3 mode exec cmd command perfmon
privilege level 3 mode exec cmd ping command
mode privileged exec command cmd level 3
logging of the privilege level 3 mode exec cmd commands
privilege level 3 exec command failover mode cmd
privilege level 3 mode exec command packet cmd - draw
privilege show import at the level 5 exec mode command
privilege level 5 see fashion exec running-config command
order of privilege show level 3 exec mode reload
privilege level 3 exec mode control fashion show
privilege see the level 3 exec firewall command mode
privilege see the level 3 exec mode command ASP.
processor mode privileged exec command to see the level 3
privilege command shell see the level 3 exec mode
privilege show level 3 exec command clock mode
privilege exec mode level 3 dns-hosts command show
privilege see the level 3 exec command access-list mode
logging of orders privilege see the level 3 exec mode
privilege, level 3 see the exec command mode vlan
privilege show level 3 exec command ip mode
privilege, level 3 see fashion exec command ipv6
privilege, level 3 see the exec command failover mode
privilege, level 3 see fashion exec command asdm
exec mode privilege see the level 3 command arp
command routing privilege see the level 3 exec mode
privilege, level 3 see fashion exec command ospf
privilege, level 3 see the exec command in aaa-server mode
AAA mode privileged exec command to see the level 3
privilege, level 3 see fashion exec command eigrp
privilege see the level 3 exec mode command crypto
privilege, level 3 see fashion exec command vpn-sessiondb
privilege level 3 exec mode command ssh show
privilege, level 3 see fashion exec command dhcpd
privilege, level 3 see the vpnclient command exec mode
privilege, level 3 see fashion exec command vpn
privilege level see the 3 blocks from exec mode command
privilege, level 3 see fashion exec command wccp
privilege see the level 3 exec command mode dynamic filters
privilege, level 3 see the exec command in webvpn mode
privilege control module see the level 3 exec mode
privilege, level 3 see fashion exec command uauth
privilege see the level 3 exec command compression mode
level 3 for the show privilege mode configure the command interface
level 3 for the show privilege mode set clock command
level 3 for the show privilege mode configure the access-list command
level 3 for the show privilege mode set up the registration of the order
level 3 for the show privilege mode configure ip command
level 3 for the show privilege mode configure command failover
level 5 mode see the privilege set up command asdm
level 3 for the show privilege mode configure arp command
level 3 for the show privilege mode configure the command routing
level 3 for the show privilege mode configure aaa-order server
level mode 3 privilege see the command configure aaa
level 3 for the show privilege mode configure command crypto
level 3 for the show privilege mode configure ssh command
level 3 for the show privilege mode configure command dhcpd
level 5 mode see the privilege set privilege to command
privilege level clear 3 mode exec command dns host
logging of the privilege clear level 3 exec mode commands
clear level 3 arp command mode privileged exec
AAA-server of privilege clear level 3 exec mode command
privilege clear level 3 exec mode command crypto
privilege clear level 3 exec command mode dynamic filters
level 3 for the privilege cmd mode configure command failover
clear level 3 privilege mode set the logging of command
privilege mode clear level 3 Configure arp command
clear level 3 privilege mode configure command crypto
clear level 3 privilege mode configure aaa-order server
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4
: end
Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.
The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.
On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.
-
Easy VPN not able to access the local network
Hi guys,.
little hope can help me, I'll give you a run down on the config.
I have a border router that is a no. 2851 connected to the No. 2851 is a switch cisco 3750 running Routing inter - vlan with four VLANS.
I have easy VPN server on the edge router No. 2851 I am able to connect remotely from a client vpn cisco with a problem but I can't access the local network on the server, I tried everything with no luck.
I have a cisco VPN client installed on a 64-bit windows system 7 and I also tried with windows xp 32-bit system and still no luck.
Please I need help I need to get this race to end of trading today.
I will be copying and pasting the edge router config please if someone get review and see if the config is good.
You need to change your ACL PAT of standard to extend and to deny traffic to be translated to the Pool of VPN:
access-list 120 deny ip 10.10.10.0 0.0.0.3 10.10.50.0 0.0.0.255
access-list 120 deny ip 192.168.XX.0 0.0.0.255 10.10.50.0 0.0.0.255
access-list 120 deny ip 172.16.XX.0 0.0.0.255 10.10.50.0 0.0.0.255
access-list 120 deny ip 172.1X.20.0 0.0.0.255 10.10.50.0 0.0.0.255
access-list 120 deny ip 192.168.XX.0 0.0.0.255 10.10.50.0 0.0.0.255
access-list 120 allow ip 10.10.10.0 0.0.0.3 all
IP access-list 120 permit 192.168.XX.0 0.0.0.255 any
IP access-list 120 permit 172.16.XX.0 0.0.0.255 aniy
IP access-list 120 permit 172.1X.20.0 0.0.0.255 any
IP access-list 120 permit 192.168.XX.0 0.0.0.255 any
overload of IP nat inside source list 120 interface Dialer0
no nat ip within the source of the list 1 overload interface Dialer0
clear the ip nat trans *.
Hope that helps.
-
I'm portable computer maintenance of the customer, a Toshiba Satellite L305-S5885, under Vista Home Premium x 86 SP2, with infections by malicious software and internet connection problems. I have managed to get rid of all of its 251 infections and I am now addressing the connectivity problem. I'm unable to achieve on its ethernet or a wireless connection to Internet. The two network status of connections 'Unidentified network', and also ' access: Local only ' all other machines hooked up to my router via CAT5e and some via 802.11 g/n, have excellent speeds with internet connectivity, so I know that the problem is limited to his machine. I tried the following:
Deactivation and reactivation of these two connections: FAIL.
"Diagnose and repair" on the two connections: FAIL.
Under dynamic I.P. type to static/static to the dynamic: FAIL.
Uninstalled all network via Device Manager devices, then restart: FAIL.
Manually uninstalled all the drivers and utility and installed the latest versions: FAIL
The command ipconfig/all text follows:
----------------------------------------------
Microsoft Windows [Version 6.0.6002]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.C:\Users\Brooklyn's>ipconfig/all
Windows IP configuration
Name of the host...: Brooklyns-PC
Primary Dns suffix...:
Node... type: broadcast
Active... IP routing: No.
Active... proxy WINS: No.Wireless network connection Wireless LAN adapter:
The connection-specific DNS suffix. :
... Description: Intel (r) Wireless WiFi Link 4965AGN
Physical address.... : 00-21-5C-31-87-95
DHCP active...: Yes
Autoconfiguration enabled...: Yes
Autoconfiguration IPv4 address. . : 169.254.174.235 (Preferred)
... Subnet mask: 255.255.0.0.
... Default gateway. :
NetBIOS over TCP/IP...: enabledEthernet connection to the Local network card:
The connection-specific DNS suffix. :
Description...: Realtek RTL8102E Family PCI - E Fast Ethern
and NIC (NDIS 6.0)
Physical address.... : 00-1E-33-4E-2E-F7
DHCP active...: Yes
Autoconfiguration enabled...: Yes
Autoconfiguration IPv4 address. . : 169.254.74.29 (Preferred)
... Subnet mask: 255.255.0.0.
... Default gateway. :
NetBIOS over TCP/IP...: enabledCard tunnel Local Area Connection * 6:
State of the media...: Media disconnected
The connection-specific DNS suffix. :
... Description: isatap. {C41651CC-0B3D-411D-8187-745214 C 69}
B4B}
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: YesCard tunnel Local Area Connection * 11:
State of the media...: Media disconnected
The connection-specific DNS suffix. :
... Description: isatap. {816357D 3-D 8-494C-AA09-F622AE861 44}
0FA}
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: YesCard tunnel Local Area Connection * 14:
State of the media...: Media disconnected
The connection-specific DNS suffix. :
... Description: Teredo Tunneling Pseudo-Interface
Physical address.... : 02-00-54-55-4E-01
DHCP active...: No.
Autoconfiguration enabled...: YesC:\Users\Brooklyn's >
--------------------------------------------------Guys, I'm really hitting my head against the wall on this one, and I would be VERY happy for any help through this. Thank you!
I thought about it, there was a corrupted installation of Norton 360, the origin of the problem. I've used the Norton removal tool and voila! Internet! Thank you.
-
Customer Cisco PIX 501 VPN connects but no connection to the local network
Hi all:
I am able to make a VPN connection to a PIX 501. The remote client is assigned an IP (192.168.2.1) also, but not able to access all the machines in the local network connected to the PIX.
I have attached the PIX configuration.
Advice will be greatly appreciated.
********************
6.3 (5) PIX version
interface ethernet0 car
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
enable password xxxx
passwd xxxxx
pixfirewall hostname
domain ciscopix.com
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
access-list 102 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP address outside dhcp setroute
IP address inside 192.168.1.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP local pool ippool 192.168.2.1 - 192.168.2.5
location of PDM 192.168.2.0 255.255.255.0 outside
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) - 0 102 access list
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set esp - esp-md5-hmac RIGHT
Crypto-map dynamic dynmap 10 transform-set RIGHT
map mymap 10-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
ISAKMP allows outside
ISAKMP identity address
part of pre authentication ISAKMP policy 10
encryption of ISAKMP policy 10
ISAKMP policy 10 md5 hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
vpngroup vpn3000 ippool address pool
vpngroup vpn3000 Server dns 68.87.72.130
vpngroup vpn3000-wins 192.168.1.100 Server
vpngroup vpn3000 split tunnel 101
vpngroup vpn3000 downtime 1800
password vpngroup vpn3000 *.
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd address 192.168.1.2 - 192.168.1.33 inside
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd outside auto_config
dhcpd allow inside
Terminal width 80
Cryptochecksum:xxxx
****************
The DNS server is the one assigned to me by my ISP.
My internal network connected to the PIX is 192.168.1.1 - 192.168.1.33 and the VPN ip pool is 192.168.2.1 - 192.168.2.5
"isakmp nat-traversal 20" can do the trick.
Maybe you are looking for
-
Toshiba virtual Store account Reset - 29970
Hey, please reset account 29970
-
Upgrade NT to XP on Satellite Pro 4600
is it possible to improve NT to XP, or can I just install any version XP bootable on my 4600? or is there a special version of XP for satellite pro 4600 with all the necessary drivers?
-
HP ENVY 17 2199 El: cannot create USB recovery for win10
Hello Just tried to create a USB key for win10 (64-bit) recovery. I received a message: "we cannot create a recovery on this PC drive. Some required files are missing. To solve the problems when your PC can not start, use your Windows installation di
-
I get the message please wait until the current program is finished gel or one
I get the message please, wait until the current program is finished gel or be changed... trying to delete a program and have restarted and did a system restore nothing has fixed the problem...
-
GRRRR: calls _UNBOUND_ broken in BB10.2 as well
I can't believe how much the BlackBerry OS 10.2 broken call framework. Several of my related calls have been broken when released 10.2.0.424, but I thought I had everything working again by the way of using InvokeQuery for InvokeManager/InvokeRequest