Cisco asa active multiple interfaces on a single switch without configuration of vlan switch.
I was wondering if there is a work around on cisco asa to have 2 interfaces vlan on a switch. The reason I ask I have a cisco asa 5505 and a dell switch that does not support the configuration of VLANs. I set up 2 interface vlan on a cisco asa and when two interfaces are active my internet drops frequently. I was wondering if there is nothing to configure the asa cisco to make this thing work. Thanks in advance...
Assuming that Dell switch at least linking several interfaces of the ASA to the Dell should translate all media spanning tree protocols, but a bet covering the tree blocking State to avoid a tree covering loop.
If the Dell does not support tree covering weight then you would be in very bad shape each broadcast packet would be will loop indefinitely and cause what we call a 'broadcast storm. "
One way is not good and the other real harm.
Tags: Cisco Security
Similar Questions
-
in my cisco asa 5510 heartbeat interface
Cisco asa 5510 heartbeat interface
Of course, we will need to more information than what you have given to us. Next time, don't even bother if you want to help us...
-
Cisco ASA active / standby Mac addresses
Hi all
Please advise on the underside.
Say that I have to active / standby. I have two interfaces on each firewall configured as below
For the primary (active)
interface GigabitEthernet1 / 0--> Say burned in mac address is 6c41.6bb0.1111
nameif test1
security-level 0
10.1.1.1 IP address 255.255.255.0 ensures 10.1.1.2im int 2/0
Test2 nameif--> Say burned in mac address is 6c41.6aa0.1111
security-level 0
10.2.1.1 IP address 255.255.255.0 ensures 10.2.1.2For secondary school (currently idle)
interface GigabitEthernet1 / 0--> Say burned in mac address is 6c41.6bb0.2222
nameif test1
security-level 0
10.1.1.1 IP address 255.255.255.0 ensures 10.1.1.2im int 2/0
Test2 nameif--> Say burned in mac address is 6c41.6aa0.2222
security-level 0
10.2.1.1 IP address 255.255.255.0 ensures 10.2.1.2According to my understanding of the DOC.
To transfer traffic, other devices will use the main unit mac address and IP addresses.
Please consider under the scenario:
My primary unit has failed and secondary took over as active unit.
Primary (standby)
Secondary (active)
secondary Q1) so now will use the IP address and Mac address as below? Please confirm
10.1.1.1 & 6c41.6bb0.1111
10.2.1.1 & 6c41.6aa0.1111
Q2) I believe that the ip address of the primary (Standby) in aid will be
10.1.1.2
10.2.1.2
It will use what mac addresses? What is the BIA of the secondary unit? Please notify
Thanks in advance.
Q1 Yes), IP address and the MAC will be moving to the new active unit so no matter who the network except the switch will notice failover event
Q2) Yes, primary (watch now) will use IP addresses and MAC addresses available for secondary:
6C41.6bb0.2222
6C41.6aa0.2222
Kind regards.
-
licenses for a cisco ASA active/passive pair AnyConnect SSL
Hi all. I buy 2 5512 x ASAs is configured like a pair of active/passive as a VPN device. I need to purchase licenses for both devices anyconnect? Thank you
Licenses AnyConnect Essentials (or premium) are combined on a cluster failover ASA. Reference
So, buy once only the quantity and type of licenses you need based on your end users - not based on the number of ASAs - and they will be available at the ASA Active whether primary or secondary unit.
-
Cisco ASA 5510 multiple dynamic config VPN L2L necessary
Hello
We have a Cisco asa 5510 with static IP address. Also, we have a remote office with a dynamic IP address. We now have a dynamic to static VPN configured L2L. And now, we must add new tunnel to another site with a dynamic IP address. Is this possible? Does anyone have an example of woking, or manual?
Oleg Kobelev
The config only you need in the ASA is: -.
(1) set of crypto processing
(2) political ISAKMP
(3) dynamic Crypto map
(4) default group L2L & PSK
(5) Config RRI (reverse Route Injection)
HTH >
-
Save multiple messages in a single file without cut and paste each individual email.
How to save several hotmail/windows live mail simultaneously to another file format, such as Word? I don't want to open it, copy and paste each one email at a time. It's tedious, so I have several emails that I need to transfer a single file as a Word document.
Hello
As you are referring to Hotmail and Windows Live Mail, I suggest you to refer to the links and post your application in the Windows Live forums to improve the assistance:
Hotmail
http://windowslivehelp.com/product.aspx?ProductID=1
Windows Live Mail
-
Conslidating multiple LUNS in a single lun without data loss
I have original started with 2-50 GB LUN as drive C and D for a virtual machine. Since then, we have had some problems with the virtual machine and wishes to consolidate the LUN down to one 100 GB LUN with a partition C and D.
I think that I should just clone the virtual machine through to store 100 GB data and the value of the c: 50BG then attach the drive D: current LUN and copy files to your new partition. This will be a thing of your time if this idea works and I have to repeat the process on multiple machines.
Has anyone found a better way to run this process by cloning or svmotion?
Thanks for the help.
So you created 2 50 GB LUN on your San with the VMDK for C on a LUN and the VMDK for others the lun or have you created 2 50 GB VMDK for the virtual machine in a data store?
If you have found this helpful at all prices please points using the correct or useful! Thank you!
-
How to assign a range of interfaces to a single VLAN?
How can I assign ports or multiple interfaces to a single VLAN. I use multilayer switches.
Hello
example of
interface series g1/0/1 - 18
switchport access vlan 10
-
Error message 5545 ASA Cisco: % ASA-3-210007: READ allocate xlate failed
Hello team,
We have 2 firewall Cisco ASA, active failover / standby.
the waiting for firewall, we see this error message "% ASA-3-210007: READ allocate xlate failed.
This error message is related to the bug?
Thank you for your help,
Best regards
Yunus Saleh
Hi Younous,
This error on the rescue unit could be associated with a problem of memory on the device or memory full on the device.
IF these options are not confirmed, we can consider that your devices version is bug hit.
https://Tools.Cisco.com/bugsearch/bug/CSCub94479/?referring_site=bugquic...
BTW, you send us the "sh version" of your device.
If your version is 'old' or connected to the version mentioned in the BUG system, is high suggests updating your device.
In a law/stb Setup, are also "0 downtime" and updated easy both devices
Let me know
Matteo
Please rate me if the post was beneficial for your solution / questions
-
Cisco ASA 5510 - IOS upgrade 7.0 failing. Not found Flash BIOS
Hello everyone
I have a Cisco ASA 5510 in a lab with none of the configurations environment what so ever.
Objective: upgrade the IOS current version 7.0 (8) to 7.1.1 (possibly go to 8.2 until memory upgrade on the SAA: 256 MB to 1 GB and then move to the latest version of 8.2 IOS).
Output to see the attached Version.
Output Flash attached show.
asa711 - k8.bin is the file that has been copied from a TFTP server to flash.
The following commands have been executed in order to update the IOS
ciscoasa (config) # boot flash system: / asa711 - k8.bin
INFO: Conversion of flash: / asa711 - k8.bin to disk0: / asa711 - k8.bin
ciscoasa (config) #.
ciscoasa (config) # end
ciscoasa # write memory
Cryptochecksum: aaaa08ce ccde38f2 19c42e08 dea24cbd
2713 bytes copied in 1,450 dry (2713 bytes/s)
[OK]
ciscoasa # reloadPROBLEM: the device ASA goes in an infinite loop (guard restart). This is the message on the console:
The system boot, please wait...
CISCO SYSTEMS
Embedded BIOS Version 1.0 (11) 15:11:51.82 5 08/28/08
Memory: 631ko
Memory: 256 MB
PCI device table.
Bus Dev Func VendID DevID class Irq
00 00 00 8086 2578 host Bridge
00 01 00 8086 2579 PCI to PCI bridge
00 03 00 8086 PCI bridge to PCI 257 b
00 1 00 8086 PCI bridge to PCI 25AE
1 d 00 00 8086 25A 9 Serial Bus 11
1 00 01 8086 25AA Bus series 10 d
1 d 00 04 8086 25AB system
1 d 00 05 8086 25AC IRQ controller
1 d 00 07 8086 25AD Bus series 9
1E 00 00 8086 PCI bridge to 244th PCI
1F 00 00 8086 25A 1 ISA Bridge
1F 00 02 8086 25 IDE controller has 3 11
1F 00 03 8086 25A 4 Bus series 5
1F 00 05 8086 25A 6 Audio 5
02 01 00 8086 1075 Ethernet 11
03 01 00 177 D 0003 encrypt/decrypt 9
03 02 00 8086 1079 Ethernet 9
03 02 01 8086 1079 Ethernet 9
03 03 00 8086 1079 Ethernet 9
03 03 01 8086 1079 Ethernet 9
04 02 00 8086 1209 Ethernet 11
04 03 00 8086 1209 Ethernet 5
Evaluate the BIOS Options...
Launch of the BIOS Extension installation ROMMON
Cisco Systems ROMMON Version (1.0 (11) 5) #0: Thu Aug 28 15:23:50 CDT 2008
Platform ASA5510
Use BREAK or ESC to interrupt the boot.
Use the SPACE to start boot immediately.
Start the program boot...
Startup configuration file contains 1 entry.Load disk0: / asa711 - k8.bin... The starting...
256 MB OF RAM
Total of SSMs found: 0
Total cards network found: 7
mcwa i82557 Ethernet to irq 11 MAC: 0024.974a.65af
mcwa i82557 Ethernet to the irq 5 MAC: 0000.0001.0001
Not found BIOS flash.
Reset...The only way for me to do things to normal is if I BREAK the sequence starting with ESC and go into ROMMON mode. I then issue a start command for the SAA to start with 7.0 (8) default IOS Image.
Please can someone explain what is the problem here?
Apologies if I'm missing something obvious that I'm not an expert of the SAA.
Looks like that the ASA is hitting a field notice: fn62378. The FN, it's because of the incompatible version of hardware and software. Please upgrade to version 7.1.2 instead of 7.1.1. If you plan to spend in 8.2. So instead of going 7.1.2 you could go to 7.2.5 (recommanded), then 8.2.5
http://www.Cisco.com/c/en/us/support/docs/field-notices/620/fn62378.html
It will be useful.
Kind regards
Akshay Rouanet
Remember messages useful rate.
-
All,
I use the cisco ASA 5500 vpn device, and I need a specific configuration where clients vpn (vpn without customer) would authenticate in an external radius server.
My problem is that I need to do different bookmarks for different users, so how can I do if my clients are not in the local database? (I do not even have accounts configured on the cisco device), DAP would be the solution?
TKS in advance
You are absolutely right. You can configure DAP to make specific bookmarks according to which the user connects via the WebVPN (Clientless SSL VPN).
-
Implement MLAG with a single switch running
Hello
IM MLAG with two N4032F to a server and failover and balancing of load testing work. A problem I encounter is that the MLAG interface is wrong until the two switches are running. Can I somehow force the MLAG interface then go to the top with a single switch running? Let's say after power failure, where only the switch starts.
CEST
Running closed and no stop on the channel of port to the server displays the interface with a single switch running.
-
Cisco ASA 5505 site for multiple subnet of the site.
Hello. I need help to configure my cisco asa 5505.
I set up a VPN between two ASA 5505 tunnel
Site 1:
Subnet 192.168.77.0
Site 2:
Have multiple VLANs and now the tunnel goes to vlan400 - 192.168.1.0
What I need help:
Site 1, I need to be able to reach a different virtual LAN on site 2. vlan480 - 192.168.20.0
And 1 site I have to reach 192.168.77.0 subnet of vlan480 - 192.168.20.0
Vlan480 is used for phones. In vlan480, we have a PABX.
Is this possible to do?
Any help would be much appreciated!
Config site 2:
: Saved
:
ASA Version 7.2 (2)
!
ciscoasa hostname
domain default.domain.invalid
activate the password encrypted x
names of
name 192.168.1.250 DomeneServer
name of 192.168.1.10 NotesServer
name 192.168.1.90 Steadyily
name 192.168.1.97 TerminalServer
name 192.168.1.98 eyeshare w8
name 192.168.50.10 w8-print
name 192.168.1.94 w8 - app
name 192.168.1.89 FonnaFlyMedia
!
interface Vlan1
nameif Vlan1
security-level 100
IP 192.168.200.100 255.255.255.0
OSPF cost 10
!
interface Vlan2
nameif outside
security-level 0
IP address 79.x.x.226 255.255.255.224
OSPF cost 10
!
interface Vlan400
nameif vlan400
security-level 100
IP 192.168.1.1 255.255.255.0
OSPF cost 10
!
interface Vlan450
nameif Vlan450
security-level 100
IP 192.168.210.1 255.255.255.0
OSPF cost 10
!
interface Vlan460
nameif Vlan460-SuldalHotell
security-level 100
IP 192.168.2.1 255.255.255.0
OSPF cost 10
!
interface Vlan461
nameif Vlan461-SuldalHotellGjest
security-level 100
address 192.168.3.1 IP 255.255.255.0
OSPF cost 10
!
interface Vlan462
Vlan462-Suldalsposten nameif
security-level 100
192.168.4.1 IP address 255.255.255.0
OSPF cost 10
!
interface Vlan470
nameif vlan470-Kyrkjekontoret
security-level 100
IP 192.168.202.1 255.255.255.0
OSPF cost 10
!
interface Vlan480
nameif vlan480 Telefoni
security-level 100
address 192.168.20.1 255.255.255.0
OSPF cost 10
!
interface Vlan490
nameif Vlan490-QNapBackup
security-level 100
IP 192.168.10.1 255.255.255.0
OSPF cost 10
!
interface Vlan500
nameif Vlan500-HellandBadlands
security-level 100
192.168.30.1 IP address 255.255.255.0
OSPF cost 10
!
interface Vlan510
Vlan510-IsTak nameif
security-level 100
192.168.40.1 IP address 255.255.255.0
OSPF cost 10
!
interface Vlan600
nameif Vlan600-SafeQ
security-level 100
192.168.50.1 IP address 255.255.255.0
OSPF cost 10
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
switchport access vlan 500
switchport trunk allowed vlan 400,450,460-462,470,480,500,510,600,610
switchport mode trunk
!
interface Ethernet0/3
switchport access vlan 490
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passwd encrypted x
passive FTP mode
clock timezone WAT 1
DNS server-group DefaultDNS
domain default.domain.invalid
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
Lotus_Notes_Utgaaande tcp service object-group
UT og Frim Notes Description til alle
area of port-object eq
port-object eq ftp
port-object eq www
EQ object of the https port
port-object eq lotusnotes
EQ Port pop3 object
EQ pptp Port object
EQ smtp port object
Lotus_Notes_inn tcp service object-group
Description of the inn og alle til Notes
port-object eq www
port-object eq lotusnotes
EQ Port pop3 object
EQ smtp port object
object-group service Reisebyraa tcp - udp
3702 3702 object-port Beach
5500 5500 object-port Beach
range of object-port 9876 9876
object-group service Remote_Desktop tcp - udp
Description Tilgang til Remote Desktop
3389 3389 port-object range
object-group service Sand_Servicenter_50000 tcp - udp
Description program tilgang til sand service AS
object-port range 50000 50000
VNC_Remote_Admin tcp service object-group
Description Fra ¥ oss til alle
5900 5900 port-object range
object-group service Printer_Accept tcp - udp
9100 9100 port-object range
port-object eq echo
ICMP-type of object-group Echo_Ping
echo ICMP-object
response to echo ICMP-object
object-group service Print tcp
9100 9100 port-object range
FTP_NADA tcp service object-group
Suldalsposten NADA tilgang description
port-object eq ftp
port-object eq ftp - data
Telefonsentral tcp service object-group
Hoftun description
port-object eq ftp
port-object eq ftp - data
port-object eq www
EQ object of the https port
port-object eq telnet
Printer_inn_800 tcp service object-group
Fra 800 thought-out og inn til 400 port 7777 description
range of object-port 7777 7777
Suldalsposten tcp service object-group
Description send av mail hav Mac Mail at - Ã ¥ nrep smtp
EQ Port pop3 object
EQ smtp port object
http2 tcp service object-group
Beach of port-object 81 81
object-group service DMZ_FTP_PASSIVE tcp - udp
55536 56559 object-port Beach
object-group service DMZ_FTP tcp - udp
20 21 object-port Beach
object-group service DMZ_HTTPS tcp - udp
Beach of port-object 443 443
object-group service DMZ_HTTP tcp - udp
8080 8080 port-object range
DNS_Query tcp service object-group
of domain object from the beach
object-group service DUETT_SQL_PORT tcp - udp
Description for a mellom andre og duett Server nett
54659 54659 object-port Beach
outside_access_in of access allowed any ip an extended list
outside_access_out of access allowed any ip an extended list
vlan400_access_in list extended access deny ip any host 149.20.56.34
vlan400_access_in list extended access deny ip any host 149.20.56.32
vlan400_access_in of access allowed any ip an extended list
Vlan450_access_in list extended access deny ip any host 149.20.56.34
Vlan450_access_in list extended access deny ip any host 149.20.56.32
Vlan450_access_in of access allowed any ip an extended list
Vlan460_access_in list extended access deny ip any host 149.20.56.34
Vlan460_access_in list extended access deny ip any host 149.20.56.32
Vlan460_access_in of access allowed any ip an extended list
vlan400_access_out list extended access permit icmp any any Echo_Ping object-group
vlan400_access_out list extended access permit tcp any host NotesServer object-group Lotus_Notes_Utgaaande
vlan400_access_out list extended access permit tcp any host DomeneServer object-group Remote_Desktop
vlan400_access_out list extended access permit tcp any host TerminalServer object-group Remote_Desktop
vlan400_access_out list extended access permit tcp any host http2 object-group Steadyily
vlan400_access_out list extended access permit tcp any host NotesServer object-group Lotus_Notes_inn
vlan400_access_out list extended access permit tcp any host NotesServer object-group Remote_Desktop
vlan400_access_out allowed extended access list tcp any host w8-eyeshare object-group Remote_Desktop
vlan400_access_out allowed extended access list tcp any host w8 - app object-group Remote_Desktop
vlan400_access_out list extended access permit tcp any host FonnaFlyMedia range 8400-8600
vlan400_access_out list extended access permit udp any host FonnaFlyMedia 9000 9001 range
vlan400_access_out list extended access permitted tcp 192.168.4.0 255.255.255.0 host DomeneServer
vlan400_access_out list extended access permitted tcp 192.168.4.0 255.255.255.0 host w8 - app object-group DUETT_SQL_PORT
Vlan500_access_in list extended access deny ip any host 149.20.56.34
Vlan500_access_in list extended access deny ip any host 149.20.56.32
Vlan500_access_in of access allowed any ip an extended list
vlan470_access_in list extended access deny ip any host 149.20.56.34
vlan470_access_in list extended access deny ip any host 149.20.56.32
vlan470_access_in of access allowed any ip an extended list
Vlan490_access_in list extended access deny ip any host 149.20.56.34
Vlan490_access_in list extended access deny ip any host 149.20.56.32
Vlan490_access_in of access allowed any ip an extended list
Vlan450_access_out list extended access permit icmp any any Echo_Ping object-group
Vlan1_access_out of access allowed any ip an extended list
Vlan1_access_out list extended access permit tcp any host w8-print object-group Remote_Desktop
Vlan1_access_out deny ip extended access list a whole
Vlan1_access_out list extended access permit icmp any any echo response
Vlan460_access_out list extended access permit icmp any any Echo_Ping object-group
Vlan490_access_out list extended access permit icmp any any Echo_Ping object-group
Vlan490_access_out list extended access permit tcp any host 192.168.10.10 object-group DMZ_FTP
Vlan490_access_out list extended access permit tcp any host 192.168.10.10 object-group DMZ_FTP_PASSIVE
Vlan490_access_out list extended access permit tcp any host 192.168.10.10 object-group DMZ_HTTPS
Vlan490_access_out list extended access permit tcp any host 192.168.10.10 object-group DMZ_HTTP
Vlan500_access_out list extended access permit icmp any any Echo_Ping object-group
vlan470_access_out list extended access permit icmp any any Echo_Ping object-group
vlan470_access_out list extended access permit tcp any host 192.168.202.10 - group Remote_Desktop object
Vlan510_access_out list extended access permit icmp any any Echo_Ping object-group
vlan480_access_out of access allowed any ip an extended list
Vlan510_access_in of access allowed any ip an extended list
Vlan600_access_in of access allowed any ip an extended list
Vlan600_access_out list extended access permit icmp any one
Vlan600_access_out list extended access permit tcp any host w8-print object-group Remote_Desktop
Vlan600_access_out list extended access permitted tcp 192.168.1.0 255.255.255.0 host w8-printing eq www
Vlan600_access_out list extended access permitted tcp 192.168.202.0 255.255.255.0 host w8-printing eq www
Vlan600_access_out list extended access permitted tcp 192.168.210.0 255.255.255.0 host w8-printing eq www
Vlan600_access_in_1 of access allowed any ip an extended list
Vlan461_access_in of access allowed any ip an extended list
Vlan461_access_out list extended access permit icmp any any Echo_Ping object-group
vlan400_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.77.0 255.255.255.0
outside_20_cryptomap_1 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.77.0 255.255.255.0
outside_20_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.77.0 255.255.255.0
access-list Vlan462-Suldalsposten_access_in extended ip allowed any one
access-list Vlan462-Suldalsposten_access_out extended permit icmp any any echo response
access-list Vlan462-Suldalsposten_access_out_1 extended permit icmp any any echo response
access-list Vlan462-Suldalsposten_access_in_1 extended ip allowed any one
pager lines 24
Enable logging
asdm of logging of information
MTU 1500 Vlan1
Outside 1500 MTU
vlan400 MTU 1500
MTU 1500 Vlan450
MTU 1500 Vlan460-SuldalHotell
MTU 1500 Vlan461-SuldalHotellGjest
vlan470-Kyrkjekontoret MTU 1500
MTU 1500 vlan480-Telefoni
MTU 1500 Vlan490-QNapBackup
MTU 1500 Vlan500-HellandBadlands
MTU 1500 Vlan510-IsTak
MTU 1500 Vlan600-SafeQ
MTU 1500 Vlan462-Suldalsposten
no failover
Monitor-interface Vlan1
interface of the monitor to the outside
the interface of the monitor vlan400
the interface of the monitor Vlan450
the interface of the Vlan460-SuldalHotell monitor
the interface of the Vlan461-SuldalHotellGjest monitor
the interface of the vlan470-Kyrkjekontoret monitor
Monitor-interface vlan480-Telefoni
the interface of the Vlan490-QNapBackup monitor
the interface of the Vlan500-HellandBadlands monitor
Monitor-interface Vlan510-IsTak
Monitor-interface Vlan600-SafeQ
the interface of the monitor Vlan462-Suldalsposten
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 522.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
vlan400_nat0_outbound (vlan400) NAT 0 access list
NAT (vlan400) 1 0.0.0.0 0.0.0.0 dns
NAT (Vlan450) 1 0.0.0.0 0.0.0.0 dns
NAT (Vlan460-SuldalHotell) 1 0.0.0.0 0.0.0.0
NAT (Vlan461-SuldalHotellGjest) 1 0.0.0.0 0.0.0.0
NAT (vlan470-Kyrkjekontoret) 1 0.0.0.0 0.0.0.0
NAT (Vlan490-QNapBackup) 1 0.0.0.0 0.0.0.0 dns
NAT (Vlan500-HellandBadlands) 1 0.0.0.0 0.0.0.0
NAT (Vlan510-IsTak) 1 0.0.0.0 0.0.0.0
NAT (Vlan600-SafeQ) 1 0.0.0.0 0.0.0.0
NAT (Vlan462-Suldalsposten) 1 0.0.0.0 0.0.0.0
static (vlan400, external) 79.x.x.x DomeneServer netmask 255.255.255.255
static (vlan470-Kyrkjekontoret, external) 79.x.x.x 192.168.202.10 netmask 255.255.255.255
static (vlan400, external) 79.x.x.x NotesServer netmask 255.255.255.255 dns
static (vlan400, external) 79.x.x.231 netmask 255.255.255.255 TerminalServer
static (vlan400, external) 79.x.x.234 Steadyily netmask 255.255.255.255
static (vlan400, outside) w8-eyeshare netmask 255.255.255.255 79.x.x.232
static (Vlan490-QNapBackup, external) 79.x.x.233 192.168.10.10 netmask 255.255.255.255 dns
static (Vlan600-SafeQ, external) 79.x.x.235 w8 - print subnet mask 255.255.255.255
static (vlan400, outside) w8 - app netmask 255.255.255.255 79.x.x.236
static (Vlan450, vlan400) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
(Vlan500-HellandBadlands, vlan400) static 192.168.30.0 192.168.30.0 netmask 255.255.255.0
(vlan400, Vlan500-HellandBadlands) static 192.168.1.0 192.168.1.0 netmask 255.255.255.0
(vlan400, Vlan450) static 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400, external) 79.x.x.252 FonnaFlyMedia netmask 255.255.255.255
static (Vlan462-Suldalsposten, vlan400) 192.168.4.0 192.168.4.0 netmask 255.255.255.0
static (vlan400, Vlan462-Suldalsposten) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400, Vlan600-SafeQ) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (Vlan600-SafeQ, vlan400) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan600-SafeQ, Vlan450) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan600-SafeQ, vlan470-Kyrkjekontoret) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan450, Vlan600-SafeQ) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
static (vlan470-Kyrkjekontoret, Vlan600-SafeQ) 192.168.202.0 192.168.202.0 netmask 255.255.255.0
Access-group interface Vlan1 Vlan1_access_out
Access-group outside_access_in in interface outside
Access-group outside_access_out outside interface
Access-group vlan400_access_in in the vlan400 interface
vlan400_access_out group access to the interface vlan400
Access-group Vlan450_access_in in the Vlan450 interface
Access-group interface Vlan450 Vlan450_access_out
Access-group interface Vlan460-SuldalHotell Vlan460_access_in
Access-group interface Vlan460-SuldalHotell Vlan460_access_out
Access-group interface Vlan461-SuldalHotellGjest Vlan461_access_in
Access-group interface Vlan461-SuldalHotellGjest Vlan461_access_out
Access-group vlan470_access_in in interface vlan470-Kyrkjekontoret
vlan470_access_out access to the interface vlan470-Kyrkjekontoret group
access to the interface vlan480-Telefoni, vlan480_access_out group
Access-group interface Vlan490-QNapBackup Vlan490_access_in
Access-group interface Vlan490-QNapBackup Vlan490_access_out
Access-group interface Vlan500-HellandBadlands Vlan500_access_in
Access-group interface Vlan500-HellandBadlands Vlan500_access_out
Access-group interface Vlan510-IsTak Vlan510_access_in
Access-group interface Vlan510-IsTak Vlan510_access_out
Access-group Vlan600_access_in_1 interface Vlan600-SafeQ
Access-group Vlan600_access_out interface Vlan600-SafeQ
Access-group Vlan462-Suldalsposten_access_in_1 Vlan462-Suldalsposten interface
Access-group Vlan462-Suldalsposten_access_out_1 Vlan462-Suldalsposten interface
Route outside 0.0.0.0 0.0.0.0 79.x.x.225 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
x x encrypted privilege 15 password username
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.210.0 255.255.255.0 Vlan450
http 192.168.200.0 255.255.255.0 Vlan1
http 192.168.1.0 255.255.255.0 vlan400
No snmp server location
No snmp Server contact
SNMP-Server Community public
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
card crypto outside_map 20 match address outside_20_cryptomap_1
card crypto outside_map 20 set pfs
peer set card crypto outside_map 20 62.92.159.137
outside_map crypto 20 card value transform-set ESP-3DES-SHA
outside_map interface card crypto outside
crypto ISAKMP allow outside
ISAKMP crypto enable vlan400
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
tunnel-group 62.92.159.137 type ipsec-l2l
IPSec-attributes tunnel-group 62.92.159.137
pre-shared-key *.
Telnet 192.168.200.0 255.255.255.0 Vlan1
Telnet 192.168.1.0 255.255.255.0 vlan400
Telnet timeout 5
SSH 171.68.225.216 255.255.255.255 outside
SSH timeout 5
Console timeout 0
dhcpd update dns both
!
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan1
!
dhcpd option 6 ip 81.167.36.3 81.167.36.11 outside interface
!
dhcpd address 192.168.1.100 - 192.168.1.225 vlan400
dhcpd option ip 6 DomeneServer 81.167.36.11 interface vlan400
dhcpd option 3 ip 192.168.1.1 interface vlan400
vlan400 enable dhcpd
!
dhcpd address 192.168.210.100 - 192.168.210.200 Vlan450
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan450
dhcpd ip interface 192.168.210.1 option 3 Vlan450
enable Vlan450 dhcpd
!
dhcpd address 192.168.2.100 - 192.168.2.150 Vlan460-SuldalHotell
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan460-SuldalHotell
dhcpd 192.168.2.1 ip interface option 3 Vlan460-SuldalHotell
dhcpd enable Vlan460-SuldalHotell
!
dhcpd address 192.168.3.100 - 192.168.3.200 Vlan461-SuldalHotellGjest
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan461-SuldalHotellGjest
dhcpd ip interface 192.168.3.1 option 3 Vlan461-SuldalHotellGjest
dhcpd enable Vlan461-SuldalHotellGjest
!
dhcpd address 192.168.202.100 - 192.168.202.199 vlan470-Kyrkjekontoret
interface of dhcpd option 3 ip 192.168.202.1 vlan470-Kyrkjekontoret
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan470-Kyrkjekontoret
dhcpd enable vlan470-Kyrkjekontoret
!
dhcpd option 3 192.168.20.1 ip interface vlan480-Telefoni
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan480-Telefoni
!
dhcpd address 192.168.10.80 - 192.168.10.90 Vlan490-QNapBackup
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan490-QNapBackup
dhcpd 192.168.10.1 ip interface option 3 Vlan490-QNapBackup
!
dhcpd address 192.168.30.100 - 192.168.30.199 Vlan500-HellandBadlands
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan500-HellandBadlands
dhcpd ip interface 192.168.30.1 option 3 Vlan500-HellandBadlands
dhcpd enable Vlan500-HellandBadlands
!
dhcpd address 192.168.40.100 - 192.168.40.150 Vlan510-IsTak
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan510-IsTak
dhcpd 3 ip Vlan510-IsTak 192.168.40.1 option interface
Vlan510-IsTak enable dhcpd
!
dhcpd address 192.168.50.150 - 192.168.50.199 Vlan600-SafeQ
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan600-SafeQ
Vlan600-SafeQ enable dhcpd
!
dhcpd address 192.168.4.100 - 192.168.4.150 Vlan462-Suldalsposten
interface option 6 ip DomeneServer 81.167.36.11 Vlan462-Suldalsposten dhcpd
interface ip dhcpd option 3 Vlan462-Suldalsposten 192.168.4.1
Vlan462-Suldalsposten enable dhcpd
!
!
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
!
context of prompt hostname
Cryptochecksum:x
: end
Site 1 config:
: Saved
:
ASA Version 7.2 (4)
!
ciscoasa hostname
domain default.domain.invalid
activate the password encrypted x
passwd encrypted x
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.77.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
PPPoE Telenor customer vpdn group
IP address pppoe setroute
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
switchport access vlan 15
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
DNS server-group DefaultDNS
domain default.domain.invalid
outside_access_in list extended access permit icmp any any disable log echo-reply
access extensive list ip 192.168.77.0 outside_1_cryptomap allow 255.255.255.0 192.168.1.0 255.255.255.0
access extensive list ip 192.168.77.0 inside_nat0_outbound allow 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 524.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Access-group outside_access_in in interface outside
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
Enable http server
http 192.168.77.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 79.160.252.226
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
outside_map interface card crypto outside
crypto ISAKMP allow inside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet 192.168.77.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0
VPDN group Telenor request dialout pppoe
VPDN group Telenor localname x
VPDN group Telenor ppp authentication chap
VPDN x x local store password username
dhcpd outside auto_config
!
dhcpd address 192.168.77.100 - 192.168.77.130 inside
dhcpd dns 192.168.77.1 on the inside interface
dhcpd option 6 ip 130.67.15.198 193.213.112.4 interface inside
dhcpd allow inside
!
dhcpd option 6 ip 130.67.15.198 193.213.112.4 outside interface
!
tunnel-group 79.160.252.226 type ipsec-l2l
IPSec-attributes tunnel-group 79.160.252.226
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:x
: end
Hello
The addition of a new network to the existing VPN L2L should be a fairly simple process.
Essentially, you need to add the network of the Crypto present ACL configurations "crypto map" . You also need to configure the NAT0 configuration for it in the appropriate interfaces of the SAA. These configurations are all made on both ends of the VPN L2L connection.
Looking at your configurations above it would appear that you need to the following configurations
SITE 1
- We add the new network at the same time the crypto ACL and ACL NAT0
access extensive list ip 192.168.77.0 outside_1_cryptomap allow 255.255.255.0 192.168.20.0 255.255.255.0
access extensive list ip 192.168.77.0 inside_nat0_outbound allow 255.255.255.0 192.168.20.0 255.255.255.0
SITE 2
- We add new ACL crypto network
- We create a new NAT0 configuration for interface Vlan480 because there is no previous NAT0 configuration
outside_20_cryptomap_1 to access extended list ip 192.168.20.0 allow 255.255.255.0 192.168.77.0 255.255.255.0
Comment by VLAN480-NAT0 NAT0 for VPN access-list
access-list VLAN480-NAT0 ip 192.168.20.0 allow 255.255.255.0 192.168.77.0 255.255.255.0
NAT 0 access-list VLAN480-NAT0 (vlan480-Telefoni)
These configurations should pretty much do the trick.
Let me know if it worked
-Jouni
-
Add the date of activation of the system of detention of intrusions and Cisco ASA FirePOWER
Good evening
I want to add detention system intrusions to Cisco ASA FirePOWER license (with I.P.S, protection MPAs., Apps and URL). Is possible that? I have to buy another license or only (not free) upgrade?
the start date of the firepower Cisco ASA license-protection starts from the purchase date or from date of activation/installation on router ASA5506-X?
Hi again, my responses below:
(3) the L-ASA5506W-TAMÁS = is the correct part number if you are looking to get the model of 5506-X Wireless ASA. Don't know why ours (CDW) site has not listed :) However, we have listed promotional SKU: L-ASA5506WTAMC-1PR. For more information, I suggest that join you your CDW account manager. If you are not a customer CDW then I would suggest that you contact your local Cisco partner dealer
(4) here's the datasheet FireSIGHT:
The device can be virtual or physical
5.1) IOS-base-2960 - I'm not sure I understand the question. Can you elaborate a bit more on what you're asking here?
5.2) I.D.S. requires no additional licenses. It is part of the solution if you buy above subscriptions. The main difference here is that IPS (Intrusion Prevention System) is deployed in line and he will drop the traffic/connections if a malicious activity is detected. IDS (Intrusion Detection System) is monitor only. Thus, if the malicious traffic is detected, firepower will alert you to this topic but he will drop all traffic.
3DES/5,3) AES will be included at the time of the references you listed.
Thank you for evaluating useful messages!
-
How is used to monitor two ASA (active/stby) with modules IPS Cisco MARCH?
Hello
The two ASA with IPS modules are in Active mode / standby. When I try to add both the two IP (active / standby) in MARCH, the MARCH will complain of duplicate names.
How set up in MARCH to monitor the ASA with IPS with topology standby active?
Thank you!
Hello
The fundamental problem with this scenario is that you have modules able non-basculement in a tipping chassis - think of the pair of failover ASA as a device and modules IPS as two completely separate devices.
Then, as we have already mentioned, add only the ASA elementary school. (High school will never be passing traffic in standby mode so it is not really necessary in MARCH) Then, with the first IPS module you can add it as a module of ASA or as a standalone device (MARCH doesn't care). With the second module IPS, the only option is to add it as a separate unit anyway.
In a failover scenario of the SAA swap IP but SPI considering you'll ever messages from ASA active you will get messages from the intellectual property of these two IPS depending on whether you are in the ASA active at the time.
Remember that you must manually reproduce all IPS configuration whenever you make a change.
HTH
Andrew.
Maybe you are looking for
-
Podcasts app does not auto-download on ios10
When I open the app to podcasts, the new charge of podcasts and will display under "Download" but essentially be suspended and not download. To get them to download, cancel the download of 'frozen' and choose 'Download now', and THEN to download pod
-
What models of apple laptops have a hard drive? I want to know who is the laptop more latest updated who still has a disk drive. When did they get rid of the disk drive on the macbook pro? I try to buy one of these laptops. one of them in 2016 have
-
Equium U400-145 - HARD drive not detected during XP installation
I am trying to install XP on a new HDD on my Equim U400-145. However, during the installation of XP it says that the installation program "found no hard drives installed on your computer. The HARD drive is seen in BIOS and I checked in another system
-
Just did a hard reset and I tried my GPS, I'm in the Philippines. After loading and chose my location, it led me to another place, another country to be exact. So, how to fix this?
-
Safari does not load pages after sleep in the active window
Please note: I'm French, so what you read is not perfect. Thank you. Hi everyone, it has been so long that I tried to solve my problem on Safari. Let me explain what happens: when I wake my Mac, some site not loading, including Youtube, Facebook and