Cisco ASA IPS with enforcement

Hi all

I don't know if this is the best place to connect to this application, because it comes to ASA and convenient best IPS.

In any case, I was wondering what the best approach is to integrate a Cisco IPS GOAL module in an existing configuration of Cisco ASA, which uses the default application in the world control - i.e.

---------------------------

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

etc etc.

global service-policy global_policy

---------------------------

I was keen to inspect all traffic that was OK coming from our Web-based interface in our environment, while I was trying to do something like:

---------------------------

class-map ips

corresponds to the list of internet access

!

ips policy-map

class ips

IPS inline fail-closed

!

global service-policy global_policy

service-policy ips outside interface

---------------------------

This configuration would allow inspection of the demand for traffic going from inside to outside, but to redirect traffic from outside within the IPS?

Thank you

As for the configuration. It should inspect traffic in both directions as apply you it globally, and the map-IPS policy, it would redirect internet traffic to the inside network.

Tags: Cisco Security

Similar Questions

  • Failover on Cisco ASA 5505 with EasyVPN

    Hello

    I've implemented a customer EasyVPN with a Cisco ASA 5505 and I am trying to configure the failover but I get this message:

    "Failover cannot be configured as Cisco Easy VPN remote is activated."

    However, I have seen in the link below, this dynamic rollover is compatible with the easy standard (and not with improved but I don't think I use easyVPN improved).

    http://www.Cisco.com/c/en/us/products/collateral/security/iOS-easy-VPN/e...

    The configuration I did through ASDM is very simple:

    vpnclient server * * *.
    vpnclient-mode client mode
    vpngroup vpnclient * password *.
    vpnclient username * password *.
    vpnclient enable

    My question is how can I implement failover with a client on a Cisco ASA 5505 EasyVPN?

    Thanks in advance

    You cannot configure the failover of a device that acts as a client

  • EzVPN between Cisco ASA 5505 (with NEM mode) and Ciscoo 881 Roure

    Hi friends,

    I configured the Cisco ASA 5505 and Cisco router with DMVPN 881. 3 offices works very well but one office remains failure. I did the same configuration for all facilities but this router does not work. Any ideas?

    Please find below the exit of 881 router Cisco:

    YF2_Tbilisi_router #.
    * 4 August 09:31:26.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:31:26.793 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
    * 4 August 09:31:26.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:31:26.793: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:31:26.793 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:31:36.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:31:36.793 4 August: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
    * 4 August 09:31:36.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:31:36.793: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:31:36.793 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 09:31:44.929 4 August: ISAKMP: (0): serving SA., its is 88961 B 34, delme is 88961 B 34
    * 4 August 09:31:46.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:31:46.793 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

    * 09:31:46.793 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
    * 09:31:46.793 4 August: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = group = Youth_Facility_2 Server_public_addr = 1.1.1.1
    * 4 August 09:31:46.793: ISAKMP:isadb_key_addr_delete: no key for address 1.1.1.1 (root NULL)
    * 09:31:46.793 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
    * 09:31:46.793 4 August: ISAKMP: Unlocking counterpart struct 0x8AA90C50 for isadb_mark_sa_deleted(), count 0
    * 09:31:46.793 4 August: ISAKMP: delete peer node by peer_reap for 1.1.1.1: 8AA90C50
    * 09:31:46.793 4 August: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
    * 09:31:46.793 4 August: ISAKMP: (0): former State = new State IKE_I_AM1 = IKE_DEST_SA

    * 4 August 09:31:47.805: del_node 2.2.2.2 src dst 1.1.1.1:500 fvrf 0 x 0, ivrf 0 x 0
    * 09:31:47.805 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

    * 4 August 09:31:47.805: ISAKMP: (0): profile of THE request is (NULL)
    * 09:31:47.805 4 August: ISAKMP: created a struct peer 1.1.1.1, peer port 500
    * 09:31:47.805 4 August: ISAKMP: new created position = 0x8AA90C50 peer_handle = 0 x 80004819
    * 09:31:47.805 4 August: ISAKMP: lock struct 0x8AA90C50, refcount 1 to peer isakmp_initiator
    * 09:31:47.805 4 August: ISAKMP: (0): client configuration parameters 87531228 adjustment
    * 09:31:47.805 4 August: ISAKMP: 500 local port, remote port 500
    * 09:31:47.805 4 August: ISAKMP: find a dup her to the tree during his B 88961, 34 = isadb_insert call BVA
    * 4 August 09:31:47.805: ISAKMP: (0): set up client mode.
    * 4 August 09:31:47.805: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
    * 4 August 09:31:47.805: ISAKMP: (0): built the seller-07 ID NAT - t
    * 4 August 09:31:47.805: ISAKMP: (0): built of NAT - T of the seller-03 ID
    * 4 August 09:31:47.805: ISAKMP: (0): built the seller-02 ID NAT - t
    * 4 August 09:31:47.805: ISKAMP: more send buffer from 1024 to 3072
    * 09:31:47.805 4 August: ISAKMP: (0): ITS been pre-shared key and XAUTH authentication using id ID_KEY_ID type
    * 09:31:47.805 4 August: ISAKMP (0): payload ID
    next payload: 13
    type: 11
    Group ID: Youth_Facility_2
    Protocol: 17
    Port: 0
    Length: 24
    * 09:31:47.805 4 August: ISAKMP: (0): the total payload length: 24
    * 09:31:47.809 4 August: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_AM
    * 09:31:47.809 4 August: ISAKMP: (0): former State = new State IKE_READY = IKE_I_AM1

    * 4 August 09:31:47.809: ISAKMP: (0): Beginner aggressive Mode Exchange
    * 4 August 09:31:47.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:31:47.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:31:57.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:31:57.809 4 August: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
    * 4 August 09:31:57.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:31:57.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:31:57.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:32:07.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:32:07.809 4 August: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
    * 4 August 09:32:07.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:32:07.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:32:07.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:32:17.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:32:17.809 4 August: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
    * 4 August 09:32:17.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:32:17.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:32:17.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:32:27.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:32:27.809 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
    * 4 August 09:32:27.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:32:27.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:32:27.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:32:37.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:32:37.809 4 August: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
    * 4 August 09:32:37.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:32:37.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:32:37.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 09:32:46.793 4 August: ISAKMP: (0): serving SA., his is 872E1504, delme is 872E1504
    * 4 August 09:32:47.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:32:47.809 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

    * 09:32:47.809 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
    * 09:32:47.809 4 August: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = group = Youth_Facility_2 Server_public_addr = 1.1.1.1
    * 4 August 09:32:47.809: ISAKMP:isadb_key_addr_delete: no key for address 1.1.1.1 (root NULL)
    * 09:32:47.809 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
    * 09:32:47.809 4 August: ISAKMP: Unlocking counterpart struct 0x8AA90C50 for isadb_mark_sa_deleted(), count 0
    * 09:32:47.809 4 August: ISAKMP: delete peer node by peer_reap for 1.1.1.1: 8AA90C50
    * 09:32:47.809 4 August: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
    * 09:32:47.809 4 August: ISAKMP: (0): former State = new State IKE_I_AM1 = IKE_DEST_SA

    * 4 August 09:32:48.909: del_node src 2.2.2.2:500 dst 1.1.1.1:500 fvrf 0 x 0, ivrf 0 x 0
    * 09:32:48.909 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

    * 4 August 09:32:48.909: ISAKMP: (0): profile of THE request is (NULL)
    * 09:32:48.909 4 August: ISAKMP: created a struct peer 1.1.1.1, peer port 500
    * 09:32:48.909 4 August: ISAKMP: new created position = 0x8AA90C50 peer_handle = 0 x 80004818
    * 09:32:48.909 4 August: ISAKMP: lock struct 0x8AA90C50, refcount 1 to peer isakmp_initiator
    * 09:32:48.909 4 August: ISAKMP: (0): client setting Configuration parameters 88C05A48
    * 09:32:48.909 4 August: ISAKMP: 500 local port, remote port 500
    * 09:32:48.909 4 August: ISAKMP: find a dup her to the tree during the isadb_insert his 87B57D38 = call BVA
    * 4 August 09:32:48.909: ISAKMP: (0): set up client mode.
    * 4 August 09:32:48.909: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
    * 4 August 09:32:48.909: ISAKMP: (0): built the seller-07 ID NAT - t
    * 4 August 09:32:48.909: ISAKMP: (0): built of NAT - T of the seller-03 ID
    * 4 August 09:32:48.909: ISAKMP: (0): built the seller-02 ID NAT - t
    * 4 August 09:32:48.909: ISKAMP: more send buffer from 1024 to 3072
    * 09:32:48.913 4 August: ISAKMP: (0): ITS been pre-shared key and XAUTH authentication using id ID_KEY_ID type
    * 09:32:48.913 4 August: ISAKMP (0): payload ID
    next payload: 13
    type: 11
    Group ID: Youth_Facility_2
    Protocol: 17
    Port: 0
    Length: 24
    * 09:32:48.913 4 August: ISAKMP: (0): the total payload length: 24
    * 09:32:48.913 4 August: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_AM
    * 09:32:48.913 4 August: ISAKMP: (0): former State = new State IKE_READY = IKE_I_AM1

    * 4 August 09:32:48.913: ISAKMP: (0): Beginner aggressive Mode Exchange
    * 4 August 09:32:48.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:32:48.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:32:58.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:32:58.913 4 August: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
    * 4 August 09:32:58.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:32:58.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:32:58.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:33:08.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:33:08.913 4 August: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
    * 4 August 09:33:08.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:33:08.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:33:08.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:33:18.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:33:18.913 4 August: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
    * 4 August 09:33:18.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:33:18.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:33:18.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:33:28.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:33:28.913 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
    * 4 August 09:33:28.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:33:28.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:33:28.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.

    There is no DMVPN on the SAA. All that you have configured, is not compatible with the ASA or something another DMVPN then. At least debugging shows that there are some EzVPN involved.

    The debug version, it seems that there is no communication on UDP/500 possible between devices. Maybe something is blocking who?

  • CISCO ASA 5515 WITH THE VERSION OF FIREPOWER

    ASA 5515 service with the power of fire. Can be managed with ASDM firepower. ?

    Anyone suggests Versions for firepower, ASDM, ASA?

    Kindly help

    You will find it useful to install the Module of firepower on ASA for the management of the premises:

    http://www.Cisco.com/c/en/us/TD/docs/security/ASA/Quick_Start/SFR/firepo...

    Thank you

    Guillaume

    Rate if this can help!

  • The services configuration of firepower on Cisco asa 5506 with ASDM

    I have a few 5506 firewalls, and they are fully licensed with services of power, control, Protection, URL filtering, malware. I have intend running and configuration of all of this on the 5506 by ASDM. I was wondering if there are guides for a basic configuration and the implementation of policies available. Something to show a basic configuration which would technically begin inspection of traffic and work. Then I can edit and make changes to my taste.

    Thank you

    My recommendation to clients is to look at the Cisco Live, BRKSEC-2018presentation. Please refer to the 56 slide from for a good overview of how policies are installed in a module of firepower.

    There are also a number of other detailed guides available in the FireSIGHT Management Center product support page should you care to learn more about customization and operations. You can also find the series of videos of ASA FirePOWER on request to Labminutes.com useful to guide you on execution of operations of your system.

  • Cisco ASA 5508 with firepower of speeds VPN

    Nice day

    Can someone tell me which is better performance Anyconnect VPN or Cisco VPN?, I intend to use a VPN for my users to connect and transfer files to a shared folder speed does.

    Also, I don't want my clients to access a Web page or portal to get the client I can install the VPN client on the client labtop.

    Is it possible to do this as well?

    Hello

    The shared screenshot has the correct option is selected.

    Yes anyconnect supports IPSEC thus:

    https://supportforums.Cisco.com/discussion/11501221/Cisco-AnyConnect-DOE...

    http://www.Cisco.com/c/en/us/support/docs/security/AnyConnect-secure-mob...

    Please visit this link for the plug ASA 5508-firepower:

    http://www.Cisco.com/c/en/us/products/collateral/security/ASA-5500-serie...

    Kind regards

    Aditya

    Please evaluate the useful messages and mark the correct answers.

  • Cisco asa 5585 syslog options for ips?

    We have CISCO ASA 5585 with a separate module for the IPS, I want to know what are the options for configuring syslog? Its almost impossible to find; and there are some forums on the internet that says cisco ips store the logs in native format / owner and cannot be exported.

    Please provide details

    Thank you.

    Click on the following link

    https://supportforums.Cisco.com/document/47881/SDEE-and-IPS

  • Questions of pre-installation on IPS on Cisco ASA Cluster

    Hello

    I'm looking for some configuration directives and IPS.

    I have a Cisco ASA Cluster with an IPS Module and I would like to know the best way to go about setting it up.

    We have a customer who requires their web servers to be protected with the IPS Module.  I have the following questions:

    1. is it possible to install the IPS in learning mode type to see what kind of traffic is hitting?

    2. can you syslog alerts?

    3. is it possible to use snmp around alert also interrupts?

    4. If you put it in promiscuous mode (SDI) what it means when you receive an alert about a possible attack, an administrator must log on the

    Firewall and block traffic if they choose to do so?  Is it possible for an administrator to block traffic (or leave if his)

    a false positive in IPS) without having to connect to the ASDM?  If you have a scenario where you don't want to give users access to

    the firewall, what is the best way to go about this?

    5. is it possible to set up an alert that if this is a DDOS email alert, if it's a handshake of split then just syslog alert?

    6. I'm afraid that if I put it with a profile he can start blocking valid traffic.  What is the best way to start with IPS to protect

    a server?

    7 if its possible to syslog, what kind of detail is the capture of syslog?  Need name attack, etc.?

    A lot of questions!  I hope someone can help

    Thanks a mill

    1. is it possible to install the IPS in learning mode type to see what kind of traffic is hitting?

    Yes. There are several ways to do this, but the easiest way is to put the sensor in promiscuous mode (in the config of the ASA)

    2. can you syslog alerts?

    N ° the cisco IPS OS doesn't support syslog.

    3. is it possible to use snmp around alert also interrupts?

    Yes. But you must set the 'action' on each signature that you want to send a trap.

    4. If you put it in promiscuous mode (SDI) what it means when you receive an alert about a possible attack, an administrator must log on the

    Firewall and block traffic if they choose to do so?  Is it possible for an administrator to block traffic (or leave if his)

    a false positive in IPS) without having to connect to the ASDM?  If you have a scenario where you don't want to give users access to

    the firewall, what is the best way to go about this?

    Who should perform the analysis of IPS events have generally sufficient privilege and access to make any changes necessary to your firewall security and IPS sensors. It takes time, knowledge and skills for the analysis of the IPS. Most customer do not have the resources to do the job that you describe.

    5. is it possible to set up an alert that if this is a DDOS email alert, if it's a handshake of split then just syslog alert?

    No syslog. You can set alerts email on a per-signature basis.

    6. I'm afraid that if I put it with a profile he can start blocking valid traffic.  What is the best way to start with IPS to protect

    a server?

    Start in "Promiscuous" mode and see what hit the signatures. Investigate them, adjust your false positive until you have a tight game, an action of signatures. Then switch to online mode.

    7 if its possible to syslog, what kind of detail is the capture of syslog?  Need name attack, etc.?

    No syslog.

    -Bob

  • Cisco ASA 8.0.4 AnyConnect works do not with Vista and IE7

    Hello

    I currently have a Cisco ASA 5520 with the latest version of the Software ASA/AMPS/Anyconnect. However I can't get Vista and IE7 to connect using the free client anyconnect VPN error message following appears

    "Setup could not start the Cisco VPN Client".

    Is there a workaround for this.

    Thanks in advance

    Eoin

    I'm glad you got it working :)

    Please evaluate the positions if find you them useful.

    Concerning

    Farrukh

  • CS-mars does support ASA 5500 with version 8.4?

    Dear all,

    My mars is not able to discover devices Cisco ASA cisco ASA 5550 with last fact IOS is compatible with the CS March...

    Thanks in advance...

    Selva

    After some googleing I found that it is not supported...

    For more information, see link below

    http://www.Cisco.com/en/us/docs/security/security_management/CS-Mars/6.1/compatibility/local_controller/dtlc6x.html#wp85319

    HTH,

    GKP

  • CSCux42019 - Cisco ASA IKEv1 and IKEv2 buffer overrun vulnerability

    Hello

    WE have a CISCO ASA 5520 with firmware 8.4.7 - 15 and let me know if this device/firmware is affected by this new vulnerability ' ASA IKEv1/IKEv2 - Buffer Overflow Vulnerability '.

    Thank you very much

    Hi Jesus,

    Yes, it is affected.

    Please upgrade the recommended patches.

    Since it is set at 8.4.7.30 you can try upgrading to this image.

    Kind regards

    Aditya

  • Cisco ASA 5505 unable to access the remote network

    Hello

    I have a Cisco ASA 5505, with 50 basic license, which is connected directly to the Modem cable with a public IP address. I have configured and active VPN on the outside interface. When connect us, we connect well without error, but we are not able to access all the resources on the remote network.

    ASA IOS version 8.2 (5)

    Remote IP network: 10.0.0.0/24

    VPN IP Pool: 192.168.102.10 - 25

    I have attached the config: llc.txt

    Please let me know if you have any questions.

    Thank you!

    Hello

    Try adding NAT 0 because inside subnet--> subnet distance

    NAT (inside) 0 access-list TEST

    TEST access ip 10.0.0.0 scope list allow 255.255.255.0 192.168.102.10 255.255.255.224

    HTH

    MS

  • Cisco ASA 5510 multiple dynamic config VPN L2L necessary

    Hello

    We have a Cisco asa 5510 with static IP address. Also, we have a remote office with a dynamic IP address. We now have a dynamic to static VPN configured L2L. And now, we must add new tunnel to another site with a dynamic IP address. Is this possible? Does anyone have an example of woking, or manual?

    Oleg Kobelev

    The config only you need in the ASA is: -.

    (1) set of crypto processing

    (2) political ISAKMP

    (3) dynamic Crypto map

    (4) default group L2L & PSK

    (5) Config RRI (reverse Route Injection)

    HTH >

  • Detection of injections SQL with IDS/IPS on cisco ASA?

    Hello

    Is it possible to detect or prevent attacks by injecting SQL using Cisco IDS / IPS on ASA or with regular expressions?

    Is any signature available in IDS/IPS for this? And what is effective, is in terms of the generation of correct alarms?

    Thanks in advance

    Deepak,

    We have several signatures to detect generic SQL injection attacks in the family x-5930 of signatures.

  • Cisco ASA Cisco 831 routing static. help with ACL, maybe?

    Hi all

    What should be a simple task turns out to be difficult and I really need help.

    The Cisco ASA obviously isn't a strong point on mine and could do with a point in the right direction. I hope that this will allow me to learn more about the ASA 5505.

    OK so I have an ASA 5505. VLAN 1 is 192.168.254.1 and VLAN 2 DHCP of my cable modem.

    I have a cisco 831 Ethernet router that will sit between my main LAN and my LAN test I want to implement for multicasting. the Cisco 831 has 1 Ethernet as 192.168.254.254 and Ethernet 0 is 10.1.1.1.

    The ASA I have an interior route 10.0.0.0 255.0.0.0 192.168.254.254.

    On the Cisco 831, there is a route 0.0.0.0 0.0.0.0 192.168.254.1. I can pass traffic via Cisco 831 to the ASA 5505 and internet, for example I can ping 8.8.8.8 and access everything on my main local network, but the other wan of any host inside the ASA 5505 is unable to ping anything on 10.1.1.x.

    Where I'm going wrong? I did all my access to my a whole ASA, but it is still unable to do anything.

    I will attached my configs with deleted passwords here and would like a good kick in the right direction. Without a doubt, it's something simple I'm missing and I'm sure it's with the ACL on the ASA 5505 like the packet tracer said that the package is abandoned due to the ACL

    Thank you. :)

    Thus, all traffic between these two LANs will travel on ASA, on the same interface.
    Then please add this command in the global configuration of the ASA:
    permit same-security-traffic intra-interface

Maybe you are looking for

  • Simultaneous playback and record real-time show levels of vibrations and his Deputy

    First of all I would like to stress that I am very new to Labview (using Labview 2011) and Assistant Sound and Vibration (Labview Signal Express 2011).  I'm starting a project to measure the speech (sound pressure using microphone) and the body of vi

  • Scanjet G4010: scanjet G4010 biased image

    We've had this scanner for a number of years now with no problems.  However, these days, the scanner started producing biased intermittently from the scanned images.  How this can be solved?

  • Is xbox free ongoing promotion?

    I recently bought a pc at Best Buy, but they said the promotion has been abandoned and yet I still see ads Microsoft advertising it.

  • Svchost.exe_EventSystem event BEX64 problem

    I have rebuilt entirely twice because of this.  At least this time it seems to occur when you install a Brother printer.  I saw the "related thread", but everything which was said was "network card drivers have been corrupted.  OK, but what I do abou

  • Spades on msn

    I can't play the multiplayer games on msn.  The site seems to have blocked me.  I asked for help to solve this, but any suggestion as to a doesnb't fix the problem.  Any help appreciated.