Cisco FWSM 6500 limit group vlan module
With licensed 20 firewalls FWSM.
not more than 16 groups of VLANs are allowed for a single module.
What is the limit of the vlan-groups with a license of 50 or more?
Lowen is right, you can actually all your VLAN map on the module with a single group. Then in the context of the system, you decide which VLAN correspond to which contexts.
In response to your question lowen, Yes, you can map several groups on a single module. I acutally do sometimes, even if it is not a practical reason to do so.
-Eric
Tags: Cisco Security
Similar Questions
-
Replacement Module supervisor in Cisco Catalyst 6500 VSS 1440
Hello forum Cisco team!
I am trying to replace a defective supervisor (Sup720 VS 10 G) on a pair of Catalyst 6509 VSS. I received the RMA and the document Replace Module, supervisor of the Cisco Catalyst 6500 Virtual Switching System 1440 (the document is attached) with the procedure. After going through the steps, I have a few questions during the installation of the new supervisor:
1. do all links (including the VSL) must be connected before feeding the new supervisor? It comes from before that image and the boot config is copied to the new supervisor.
2. once the startup config and the image is copied from the active VSS switch in the new supervisor, the document said to check orders for priority switch in the copied startup config form the active VSS, but the priority of each switch is not stored in the startup configuration as far as I know. Can you please clarify this?
My goal is to add the new supervisor engine without disrupting the current active VSS switch.
Thank you in advanced for your support!
Hey,.
With regard to your questions:
1. do all links (including the VSL) must be connected before feeding the new supervisor? It comes from before that image and the boot config is copied to the new supervisor. - Yes
2. once the startup config and the image is copied from the active VSS switch in the new supervisor, the document said to check orders for priority switch in the copied startup config form the active VSS, but the priority of each switch is not stored in the startup configuration as far as I know. Can you please clarify this? - Once you convert the switch for VSS priorities will be stored in the startup configuration file. Please visit the following link:
However, it is no longer recommended and therefore should be avoided. I suggest you not setting is not the priority.
HTH.
Kind regards
RS.
-
UCS Powershell find VLAN group VLAN
Hello
I'm running UCS Manager 2.2 with powershell module CiscoUcsPS (v1.3.1.0) and looking for all the VLANS from a specific group of VLAN.
If I run Get-UcsVlan I get all the VLANS, but this does not seem to contain any information about which group VLAN they are Member of.
If I run Get-UcsFabricNetGroup I get all groups of VLAN, but this does not seem to contain any information about VLANs, which are members of the groups.
So I thought maybe I could run the two commands, but that doesn't seem to work
Get-UcsFabricNetGroup - Ucs $UCS - Name Prod. Get-UcsVlan
Get-UcsVlan: all parameters can be solved by using named parameters.
On line: 1 char: 55
+ Get-UcsFabricNetGroup - Ucs $UCS - Name Prod. Get-UcsVlan
+ ~~~~~~~~~~~
+ CategoryInfo: InvalidArgument: (Cisco.Ucs.FabricNetGroup:PSObject) [Get-UcsVlan], ParameterBindingExce
option
+ FullyQualifiedErrorId: AmbiguousParameterSet, Cisco.Ucs.Cmdlets.GetUcsVlanAll you other ideas?
Perfect!
Take a look on
http://www.thomasmaurer.ch/2013/10/Cisco-UCS-PowerShell-ConvertTo-ucscmd...
Use the PS "Convertto-UCSCmdlet" command, then issues the UCSM GUI command sequence and voila, it will show you the PS equivalent cmdlets.
-
Hello
I can't find any information about this command: "svclc vlan-group. I found it after upgrade the sup720 12.2 (18) SXD3 to 12.2 (18) SXE2 vlan-firewall-vlan-group options configured:
svclc-group vlan 1 799,800,1000,1001
svclc-group vlan 2 786-790 793 - 796
svclc-group vlan 3 761 - 785
svclc-group vlan 4 23 741 - 760
firewall module 5-group vlan 1,2,3,4
Firewall-Group vlan 1 799,800,1000,1001
Firewall-Group vlan 2 786-790 793 - 796
Firewall-Group vlan 3 761 - 785
Firewall-Group vlan 4 23 741 - 760
Kind regards.
Volker
Ignore this command for now. It is a replica of the "firewall" commands in the new code 12.2.18SXE. " SVCLC is synonymous with online map of service and a generic command for the future. Currently, she appears when the FWSM is configured and is equivalent to the orders 'firewall '.
-
Connection Cisco UCS 6120 FI directly to Cisco Catalyst 6500?
I watch a lot of design with the Cisco UCS solution guide and everywhere it is Cisco Nexus 5000/7000 connects to the uplink ports of Cisco UCS 6120 FI with the benefits of technology to the vPC.
How about connect Cisco UCS 6120 FI directly to 10GE ports in Cisco Catalyst 6500 (without VSS and VSS)? It is possible to design?
If I use C6500VSS there will be port-channel of the aggregation of the UCS Nx10GE all the bandwidth?
And what happens if I use C6500 (without VSS) - how it will be on the many links between UCS and two boxes C6500? It will be blocked by STP? A little on the other?
Please explain to me, because we have only C6500 switches in our data center and want to test a Cisco UCS schassis.
Yes, you can connect the 6120 s to cat6500s with or without vs. With VSS, you get a vPC as port channel where 2 links to a single 6120 can be connected to different 2 6500 s in a port LACP-channel.
VSS is not necessary, you can connect a 10 G uplinks / 1 G of 1 or more of a 6120 at cat6500s. I you have 2 cat6500s (non - vss) and 2 uplinks by 6120, then you want to connect 1 cat6500-1 and the other to cat6500-2. I would recommend going ahead and creating a single port-channel port so that you can easily add the uplinks in the furture without interruption of service.
Ideally, for non - vss, I would have 4 10 uplinks by 6120; 2 in a channel port cat6500-1 and 2 in a port in cat6500-2 channel
-
a WLC 2504 does support mobility with WiSM1 on the 6500 Series group
If a WLC 2504 supports the mobility with WiSM1 on the 6500 Series group.
Model: WLC 2504
Software version: 7.3.101.0Model: WiSM1
Software version: 7.x.x.xYes and no.
Yes, mobility is supported.
No, because I don't personally recommend inter-controleur of roaming. It is true when you are dealing with 4400/WISN-1. This is even truer when you WLC running two (or more) different codes.
-
ESXi 5, link group, VLAN and the Management Interface
Greetings-
I suspect that the answer to my question is: 'Buy an another NIC Intel' but here goes:
I have a server ESXi here with 2 Intel GigE NIC, connected to the same switch managed ahead of Cisco. A (vmnic0) NETWORK card is connected to the VLAN 200 while the second (vmnic1) is connected to the VLAN 300. Ports on the Cisco are defined to access mode.
Internally, the server ESXi, vmnic0 is connected to the 'public' vSwitch, while vmnic1 is connected to the "private" vSwitch
I also updated the ESXi management IP 24 even as private vSwitch. This is the key, I suspect.
I tried to combine the two GigE interfaces in a connection unique 2xGigE and trunk two VLAN 200 and 300 through it. After struggling through the menus on the ESXi console INTERFACE, I managed to get the IP management save and who responded and was able to connect to the server with the vSphere client. I did it in X'ing the vmnic0 and vmnic1 in the configuration interface, then setting VLAN 300 in the configuration of VLANS. But I could not the team/bundle correctly in the two vSwitches vmnic interfaces. I could never attach a vmnic to one of the switches.
Can I do all this with only 2 GigE interfaces and maintain access to IP management?
SWITCH CISCO < == trunk w / VLAN 200 300 2xGigE == > SERVER ESXI
VLAN 200 is a 28 audience
VLAN 300 is a private 24 (for example: 192.168.100.0/24)
IP management is 192.168.100.2
I need to create a third VLAN for the management IP address and move? If I master, say, VLAN 400 down to the ESXi server, use another block 192.168 for his IP address, I'll be able to take the vmnic0 and vmnic1 and team on the TWO vSwitches?
Always follow me? ... :-) If I can clarify this, by all means ask. I apologize for the sort of random babbling here. Thank you!
JAS
jasonvp wrote:
Rickard Nobel wrote:
You can not have your two vmnic (physical NIC ports) connected to two vSwitches and at the same time have a "grouping". You need to delete one of the vSwitches and recreate the vSwitch remaining trade. VLAN will insulate them even different networks.
Thanks for the pointers; I finally had the opportunity to try this out and it works as expected. I EF you the 'right answer' but apparently the forum won't let me since you already have an answer of "useful".
Nice that you got it working! When you perform the actual configuration with vSwitch Hash IP and physical switch LAG config, it might be a little difficult to do things in the correct order to not lose connection to the ESXi host.
You can select this message if you wish.
-
Cisco CX - Active Directory groups
Hello
I'm starting a Cisco CX deployment. Our company has more than 1 k users. I create access policies, but I'm a little stuck on a problem. I can creat policies using the username but not the ad groups, I see that there is the option, but it does not work (it does not retrieve ad groups).
The interface wonder what follows:
Groups
Users
Identity objects
Anyone got it to work?
Make sure that your ads of research base is fairly low in the tree to display groups.
By example, if your basic search are Corp./City/users, but your groups report directly to Corp, she probably won't find and shoot groups.
-
Between Cisco ASA VPN tunnels with VLAN + hairpin.
I have two Cisco ASA (5520 and 5505) both with version 9.1 (7) with Over VPN and Security Plus licenses. I try to understand all the internet a traffic tunnel strategy VLAN especially on the 5520 above the 5505 for further routing to the internet (such as a hair/u-turn hairpin). A few warnings:
- The 5505 has a dynamically assigned internet address.
- The 5505 has sometimes no device turned on behind her, bringing interfaces down to the inside (which can cause problems from site to site).
- The 5520 cannot be a client of ezvpn due to its current role as a server of webvpn (anyconnect).
Let me know if I need to post my current config. Basically, I'm starting from scratch after several attempts.
Thank you!
- The 5505 has a dynamically assigned internet address.
You can use the following doc to set up the VPN and then this document to configure Hairping/U tuning
2. the 5505 has sometimes no device turned on behind her, bringing interfaces down to the inside (which can cause problems from site to site).
Make sure that the interface is connected to a switch so that it remains all the TIME.
3. 5520 the may not be a ezvpn customer due to she has current as one role anyconnect webvpn ()) server.
You can use dynamic VPN with normal static rather EZVPN tunnel.
Kind regards
Dinesh MoudgilPS Please rate helpful messages.
-
All Cisco ASA 5510 have the IPS modules
I am new to the use of Cisco Networking products. I gave me a mission to determine if our company 5510 and 5505 IPS/IDS. In doing my research I discoververed 5505 have no IPS/IDS, but you can buy a card and 5510 have modules IPS/IDS. How can I determine whether my 5510 modue (s) IPS/IDS
only the new x (but not the 5585) ASAs have software modules. There on the 5505 and 5510 hw modules. But first, you must bring your ASA-access in the order. You can try different browsers, but also make sure that your Java is up to date.
Sent by Cisco Support technique iPad App
-
Hello!!
We are working on a mapping between a promoter Cisco ISE group and a user group in Active Directory, but the customer wants the mapping through a RADIUS SERVER, to avoid the ISE by querying directly activate Directory.
I know it is possible to use a RADIUS SERVER as source of external identity for ISE... but, is possible to use this RADIUS SERVER for this sponsor group manages?
Thank you and best regards!
Hi Rodrigo,
The answer is no. There is no way to integrate the portal Sponsor config with a RADIUS server. Your DB for authentication Portal Sponsor options;
AD
LDAP
User internal ISE DBSent by Cisco Support technique iPhone App
-
Cisco Layer 3, singing and VLAN
I have a 5.5 vSphere install and am currently an upgrade of the network for implementation of VOIP. Switching equipment that I use is a stack of switches Cisco 3850 layer 3 and I go round and round on getting traffic vlan to work properly. I hope someone can point me in the right direction.
I have a NETWORK adapter that is connected to the switch (10GB fiber) which handles all the traffic for the esxi host (with the exception of management). VLAN ID is set to zero (0) and the load balancing is set to the original function of virtual port route.
I have 2 subnets, 10.1.0.0/16 (management, VLAN 1 and data) and 10.10.1.0/24 (voice, VLAN 10)
On the host, I Win 2012 R2 server which will host a VOIP PBX. It must be able to communicate with (VLAN 10) IP phones and other servers (vlan1).
The switches will be intervlan routing.
Finally can my question - anyone give me some advice on how to configure the interface on the Cisco for connecting fiber 10GB of my host? The actual port settings would be extremely useful. Everything I do at the end of vmware I should do differently?
In case someone falls on this in a search, here's what I ended up with, 1 Cisco switch:
switchport trunk allowed vlan 1.10
switchport mode trunk
switchport nonegotiate
switchport voice vlan 10
Cisco-switch macro description
spanning tree portfast
point to point spanning tree-type of link
The virtual switch, I set all the vlan id and route from the originating virtual port.
-
Need a script to create standard vSwitch with virtual and several computer port group VLAN
I want to create standard vSwitch for all hosts in the cluster for virtual machine port group and add one or more groups of ports VLAN for the same standard vswitch.
Kind regards
Shan
Try something like this
$clusterName = "mycluster.
$nics = "vmnic0", "vmnic1.
$vlans = 123456789
foreach ($esx in (Get-Cluster-name $clusterName |)) Get - VMHost)) {}
$sw = New - VirtualSwitch - name swX - VMHost $esx - Nic $nics - confirm: $false
$vlans | %{
New-VirtualPortGroup-name "PG $($_)" - VLanId $_ - VirtualSwitch $sw - confirm: $false
}
}
-
Port - group VLAN ID Questions
Hi guys
Can I change change the running virtual machine port group?
in the case where the virtual machine was in a group of Port named test - VLAN ID 100 and I need to change the Port Group deployment VLAN ID 105 which now means my VM will not have access to traffic on vlan 100? It's automatically or I need to change my IP or something?
and this comes from the frequently asked questions
Q: a configurable virtual machine on several VLANs?
A: you can set up a single VLAN ID for each virtual network adapter on a virtual machine. However, since you can config -.
ERUS up to four virtual cards per virtual machine, you can configure a virtual machine that spans four different VLAN.
I think I'll need to set up several virtual LANs for some virtual machines. What do mean by "set up a virtual machine that spans four different VLAN".
Thank you guys
Yes, you can certainly change the portgroup. But, remember, your new VLAN is configured properly in order to maintain the networking of virtual machine after the change.
Max on max. position 2-3 drops of ping may occur depending on your use of the network and ESX utlization of resource for the change task.
Simply go to the settings-> virtual adapter - > select new vlan-> OK
If you want your traffic to be moved to a different VLAN dynamically, it must be done at the level of the physical switch. Think of the vswitch as a "dummy" switch layer 2, it will follow policies of networking of the physical switch only, sound rather a passage only. Everything depends on the new port (nic) configured to take the new vlan correctly or not.
NUTZ
VCP 3.5
(Preparation for VCP 4)
-
I'm setting up a cisco 6509 switch with FWSM, but it a little confusing to implement. I'm following the next of the http://www.cisco.com/en/US/products/hw/modules/ps2706/products_configuration_example09186a00808b4d9f.shtmldocumentation, however, depending on the following configuration has failed. I would check if my interpretation is correct. The FWSM firewall is like a part doesn't work don't not with switch, from what I've seen on the configuration of the conversation of FWSM example with the switch through a VLAN specific and am not together, correct? If so, created because the configuration is incorrect? The next option below.
6500 switch
interface vlan 10
IP 192.168.10.1 255.255.255.0
FWSM
interface vlan 10
nameif outside
security-level 0
address 192.168.10.2 255.255.255.0
interface vlan 20
nameif inside
security-level 100
address 172.16.10.1 IP 255.255.255.0
interface vlan 30
nameif dmz
security-level 60
address 172.16.20.1 255.255.255.224
No VLAN 10,20 and 30 create 6500 switch.
Concerning
Ricardo
"not create VLAN 10,20 and 30 on the 6500 switch."
All VLANS have exist to L2 on the 6500. So, if you do a ' sh vlan "on the 6500, you should see VLAN 10,20,30. If you have not your configuration will not work.
In addition, you must have L3 vlan interface to the external interface, you have your config, IE. -
6500 switch
interface vlan 10
IP 192.168.10.1 255.255.255.0
But you must not have an interface vlan to VLAN 10 & 20 L3.
Jon
Maybe you are looking for
-
Turn by turn navigation in iOS 9.2 does not
When I try to use Google Maps or Apple maps for navigation, directions turn-by-turn only leave the first direction as I drive down the road. It is not also follow my position as I drive down the road, continually pointing to the same place to start
-
HP Deskjet 1000cse C2670A: Windows 7 64 bit driver for HP Deskjet 1000cse model C2670A
My Windows 7 PC crashed a few weeks ago and I had to do a clean reinstall Win 7 Pro. That wiped out all my programs and drivers. Everything is back now, except the driver for my printer HP Deskjet 1000cse model C2670A. Successfully, I installed a
-
KERNELBASE.dll error opening Excel under Windows 7 32 bit
Signature of the problem: Problem event name: APPCRASH Name of the application: EXCEL. EXE Application version: 12.0.6514.5000 Application timestamp: 4a89db07 Fault Module name: KERNELBASE.dll Fault Module Version: 6.1.7600.16385 Timestamp of Module
-
I couldn't find the link for the download or purchase of Adobe Dreamweaver CS3 for Windows and Mac
HelloI'm looking for Adobe Dreamweaver CS3, but I couldn't find in any Web site. If someone could provide with the download link.Thank you
-
Hi all I try to write the result of the query in a file with the code below I get incorrect argument Type: cannot convert object to string element type error to the mentioned threshold import java.io.*; import java.sql.*; import java.util.*; public c