Cisco ISR 861W, RV220W or WRVS4400N

Similar Questions

• Cisco ISR 4400 series SSLVPN Support

  Hello

  New series routers Cisco ISR 4400 support SSLVPN?

  According to the feature for this, but according to the document browser 4451-X Q & A is not.

  Does that mean I can or Canon use the AnyConnect client?

  Thank you.

  Kind regards

  Armand

  According to documents that I looked, new SRI (4300 and 4400) 4000 series doesn't support SSL VPN at all:

  http://www.Cisco.com/c/dam/en/us/products/collateral/routers/4000-series-integrated-services-routers-ISR/enterprise-routing-portfolio-poster.PDF

  http://www.Cisco.com/c/en/us/products/routers/4000-series-integrated-services-routers-ISR/series-comparison.html

  It is possible that the AnyConnect client may be still usable for IKEv2/IPSec VPN connectivity, but SSL seems to be off the table in these units.

  My guess would be that access the VPN feature is moved exclusively to the portfolio of the SAA, but which is slowed down just think.

• Default configuration of the PFS on the Cisco ISR

  Hello

  I want to learn more about the default configuration of PFS on the Cisco ISR router.

  -Introduction to IP Security (IPSec) encryption - create a Crypto map
  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_tech_note09186a0080094203.shtml#cryptomap

  You can also change the configuration of your PFS here. PFS Group1 is the default value in this example. You can change the PFS to group2, or turn off all together, you should not do.

  DT3-45 a (config) #crypto card armadillo 10 ipsec-isakmp
  DT3 - 45's (config-crypto-map) #set counterpart 192.168.10.38
  DT3 - 45 session key has seconds (config-crypto-map) #set 4000
  DT3 - 45's (config-crypto-map) #set transform-set HAAT PapaBear BabyBear
  DT3 - 45's (config-crypto-map) #match address 101
  --------

  This example has no configuration PFS PFS is set to group1.
  However, the following command reference indicates that PFS is not requested.
  Which is the correct description for the PFS setting?

  -the pfs value
  http://www.Cisco.com/en/us/docs/iOS/Security/command/reference/sec_s2.html#wp1063163

  Default values
  By default, it is not required of PFS. If no group is specified with this command, the Group1 keyword is used by default.
  -------

  Thank you for your cooperation in advance.

  Order is correct.

  If pfs set is not configured in the crypto map configuration, pfs will be negotiated not.

  If set pfs is configured without any group, then it uses default group1

  And if you do not want to use the other group, you set the group # in the command set pfs.

  I hope it is clear now.

• Configuration of Cisco's 861W N wireless network

  Hello

  I have a question for you guys. I created my cisco 861w in order to get access to the Internet at home. Everything was good except that I can not tune to work wireless N. can take you a look at my setup attached to make my network works speed N Wireless.

  Thank you in advance.

  Lazar Mihail

  Hello

  The configuration you have posted is WPA Auth and TKIP as the encryption... I have attacted the config updated the... Use this and this will give u N speeds...

  Let me know how this helps...

  Concerning

  Surendra

• Control global NAT in ASA, how on Cisco ISR

  How do I do this in a Cisco Integrated Services Router?

  Global (outside) 2 192.168.96.48 mask 255.255.255.255 subnet
  NAT (inside) 2-list of access nat_vpn

  Try below

  !

  access-list 100 permit ip 192.168.96.48 0.0.0.0 all

  !

  permit LOCAL - route 1
  corresponds to the IP 100
  match interface xx

  !

  IP nat inside source route-map interface LOCAL xx

• SSL VPN on Cisco ISR G2 license 2921?

  Hi, quick question.  We have a CISCO 2921/K9, who has all of the features securityk9 (reflects Permanent under show version)

  I thought including SSL VPN, but make a "show license all" it does not reflect that:

  J:: feature 4: SSL_VPN Version: 1.0

  License type: EvalRightToUse

  The license status: Active, in use

  The total period of assessment: 8 weeks 4 days

  Assessment period left: 8 weeks 2 days

  Used period: 1 day 5 hours

  Transition date: 11 January 2013 23:05:41

  Number of licenses: 100/0 (in-use/Violation)

  License priority: bass

  Can someone please provide some clarification?

  Thank you!

  -rya

  securityK9 does not include the SSL VPN license. This just activate the security features on the ISRG2, and you would need this license to run VPN SSL, and the SSL VPN itself license.

  Here is the URL for your reference:

  http://www.Cisco.com/en/us/docs/routers/access/sw_activation/SA_on_ISR.html#wp1151975

  To run SSL VPN, you must securityK9 and SSL VPN license.

• IPsec VPN with Cisco AnyConnect and 1921 ISR G2 router

  Hello

  Is it possible to establish a remote access VPN IPSec using Cisco Anyconnect client with router Cisco ISR G2 1921.

  If someone does share it please the sample configuration. as I've been on this topic since last week a.

  My Cisco rep recommended I have not try AnyConnect a router ISR or ASR.  So I used an Open Source client.  Don't say that AnyConnect won't work, just the route I took on my project.  I work good known configuration for a 1921 with strongSwan as a Client.  It is with IPSEC and IKEV2 using certificates for authentication.

• WRVS4400N will not route all traffic on IPsec

  All my remote sites use various routers to route all their traffic via IPsec.  However, I have a WRVS4400N w/firmware configured 2.0.2.1 with a tunnel of work.  My problem is that I need to define the Group of remote 0.0.0.0 0.0.0.0 so all traffic is forced through the IPsec tunnel and not on the local gateway.  When I make the mistake, Remote Security Group and Local security group cannot be in the same network. However, it works with Cisco/Linksys RV042.

  Any ideas?  Attached are the screenshots of each.

  Transmission of wildcard ESP isn't a feature support, therefore not documented in the product documentation. If you need a wifi router that supports this feature, you can see the series Cisco ISR, which is base IOS.

• Internal and external customers see certificate of Cisco router, NOT Exchange SSL certificate

  Cisco 876 Integrated Services router (ISR)
  Exchange Server 2010 SP1

  Customer: 2013 Outlook, OWA, ActiveSync WP7/WP8 (?)

  Put us in place a new Cisco ISR. Almost everything works fine, with a few exceptions. Exchange e-mail stopped altogether for several days until I realized that I needed to redirect the ports, SMTP, HTTP, and HTTPS, by external to the Exchange Server. Now, mail flow is fine, but...

  Every time I start Outlook, I get a certificate error. When I look at the certificate in the error popup, it points actually to certificate self-signed Cisco router. When we try to use the Windows phones, they get a "certificate error" and direct the user to the network administrator. Even with OWA: a certificate error, even if it can be "accepted" / overridden.

  Each customer can still work, with the exception of Windows phones. In Outlook and OWA, mail is always be sent and received, but must be accepted manually that the certificate is wrong before the customer takes care, and then it takes a little longer to load.

  Any ideas?

  I did "" port forwarding on the pots of 25, 80 and 443. Again, I did it yesterday and now mail seems to flow, whereas before, even if we could enter the client with Certificate error, message not be received. (There was also a problem with mail however not passed, but that was due to our mail relay provider and was set yesterday as well...)

  Everything worked fine with the previous router (obviously). It was a high-end, the level of consumption Fritz! Box commonly used in Germany. I also had to allow ports through this box is not unlike using the nat ip inside static commands on the 876, but I don't know what he could have let his own or why SRI is the Exchange Server application SSL certificate hijacking.

  Thanks in advance for any help.

  jeremyNLSO
  CCNA Routing & Switching, CCNA security
  MCITP, MCTS
  Berlin, Germany

  If we have actually figured this out today. The internal DHCP Server distributing the a DNS Server public as well as the internal DNS. The internal DNS was time and the customer became the external IP address of the public DNS and it received an unexpected cert of the router. Once we removed the public DNS servers from the DHCP server and used only DNS servers in-house, that the issue went away. Logical after we realized what was going on.

• Cisco VPN bandwidth

  Hi all

  is someone who can help me in the next question?

  We have a VPN S2S with 50Mb internet connection with Cisco no firewalls (unfortunately).
  they see the VPN tunnel doesnot use bandwidth everything.

  my plan is to implement this VPN with Cisco ISR 800Series models (cause we need them also in the future have a FlexVPN)

  based on the quallity of Cisco systems, are we going to have a better performance for the VPN?
  is it possible to manage and configure points of vpn for a better communication bettwen offices?

  Thank you in advance,
  Thomas

  I can 100% assure you series Cisco 890 flat line a circuit of 50 MB/s with crypto using media to the mix of big package and have a free unused unused production capacity.

  If you only use small packages (such as VoIP), then you're going to need a 4000 series router.

• Please ME TELL WHAT Cisco VPN internal Service Module

  I do not know what is the internal service of cisco vpn module, how it words, and where we can use it.

  Hello

  Cisco internal VPN Service Module is a Cisco ISR G2.

  I would say that the main goal is the ability to offload the encryption to a dedicated service module. Dedicated encryption protects performance when CPU utilization for other services.

  You can find the data sheet here:

  http://www.Cisco.com/en/us/prod/collateral/modules/ps2706/ps12202/data_sheet_c78-682436.html

  Also on the card you will find what routers support this module.

  Please evaluate the useful messages

  Best regards

  Eugene

• Backup job Kron uses public WAN IP by defaul

  Hello

  I have a VPN site-to site between ASA (main site) and a Cisco ISR (branch) 861W that works very well; the only problem I have is when I want to save the configuration of SRI using tftp on a station in the main site, I can't because the international search report is trying to use the public IP address as the source.

  How can I fix this, so that I can manually or schedule backups to a destination in the main site?

  Thank you.

  You should be able to define the 'tftp-source interface ip' on your router to specify the appropriate private IP address.

  Reference.

• Licensing of 1001 ASR

  Hello, try as I might I can't find a document that says;

  'How to enable encryption on a 1001 ASR' or "enable advanced ip features" on the 1001 ASR.

  Can anyone help please. My Kit list.

  Cisco ASR1001 system, Crypto, 4 GE built-in, double P/S

  Cisco ASR1001 4 GB of DRAM

  Advanced Services Cisco ASR 1000 IP license

  ASR 1001-Cisco IOS XE - UNIVERSAL ENCRYPTION

  License of IPSEC for ASR1000 series

  Upgrade from 2.5 Gbps to 5Gbps license for ASR 1001

  What is the process to activate the characteristic 2.5gbps to 5gbps or encryption?

  Thank you

  Chris

  Chris,

  All licenses feature Cisco ASR 1000 are focused on the honor; in other words, they are not applied through a product Activation Key (PAK), except for the "technology package licenses" and the license upgrade (2.5 to 5 Gbps) performance on Cisco ASR 1001 models.

  (http://www.cisco.com/en/US/prod/collateral/routers/ps9343/product_bulletin_c07-448862.html)

  Q. what are the key new features with the Cisco ASR 1001 compared to other ASR 1000 Series routers chassis?

  A. The Cisco ASR 1001 series introduced the concept of the integrated daughter (IDC) card, which is an element scalable nonland on the chassis of the ASR 1001 to provide capabilities (e/s). At the time of the first ship (FCS) client, the Cisco ASR 1001 is available in 3 different versions: the ASR 1001 frame base (part number ASR1001), ASR1001-2XOC3POS with a daughter card chassis integrated with 2 ports ASR1001-4XT3 with a daughterboard integrated with 4-port T3 and OC3 POS. The second phase of the ASR 1001 launched a new 3 chassis: ASR1001-hard DRIVE with built in 160 GB hard drive; the ASR1001-4X1GE with an integrated daughter card providing 4ports 1GE. and the ASR1001-8XCHT1E1 with an integrated daughter card providing multiplexed 8-port T1/E1. In addition, the Cisco ASR 1001 is the first chassis of the Cisco ASR 1000 series, which implements the activation of the software which is the same concept of activation of software as seen on other Cisco offerings, for example on the router Cisco ISR G2 Series. 2 different types of licences will be applied to the FCS, via the activation of the software. First of all, the sets of features offered through the basis of intellectual (K9 and non - K9), Advanced IP Services (K9 and non - K9) and Advanced Enterprise Services (K9 and non - K9). Second, the upgrade of the default execution of 2.5 Gbit/s to 5 Gbps is possible via a license to upgrade performance enabled software (part number to use when ordering of three chassis ASR1001 for the upgrade of 5 Gbps performance is FSL-ASR1001 - 5 G). Other features such as firewalls, encryption is expected to be activated on the 1001 ASR in the future software.

  How to activate a license once you have a PAK (product authorization key):

  1. go to www.cisco.com/go/license

  2. tap the PAK you received on the form and submit it;

  3 activate the license on the ASR1000.

  FAQ on https://tools.cisco.com/SWIFT/Licensing/jsp/Cisco%20Licensing%20FAQ%20-%20June%202011.pdf

  For software activation orders, appointments on:

  http://www.Cisco.com/en/us/docs/iOS/CSA/configuration/guide/csa_commands.html

  HTH.

  Cheers, Gustavo

• 2 WAE WCCP l2 only 1 gets traffic

  Hello

  I have 1 router WAN and 2 devices configured in WCCP. The configuration works very well except that only the first WAVE that sees the router and set the WCCP receives traffic. What I mean is that the two waves see the router and vice versa. When I set the WCCP link, the first WAVE to his establishment becomes WAE DRIVING and another doesn't get it packages. If I disconnect the WAE lead or change its configuration WCCP and put again, WCCP switches the other WAE and the other is now exclusevly receiving traffic. No load balancing is reached.

  First of all here is my configuration:

  1 router WAN Cisco ISR G2 2911 IOS 15.2 (1) T

  WAAS in WAVE-274 cisco 2 version 4.3.3 configured in the same way for WCCP.

  Router IP: 10.x.y.1/22

  WAVE IPs: 10.x.y.9 and 10.x.y.7 22 and default gateway is the router 10.x.y.1

  Users are on the same network 10.x.y.0/22 (is that a problem? I read in a WAAS setup guide the WAE cannot be in the same network as the users)

  Second, here is the relevant config:

  Router:
  

  IP cef

  WCCP IP 61

  WCCP IP 62

  interface GigabitEthernet0/0

  Description * LAN connection *.

  61 IP wccp redirect in

  IP addr 10.x.y.1 255.255.252.0

  !

  interface GigabitEthernet0/1

  Description * WAN connection *.

  62 IP wccp redirect in

  addr IP WAN_IP...

  !

  WAAS:
  

  primary-interface GigabitEthernet 1/0

  interface GigabitEthernet 1/0

  IP address 10.x.y.9 255.255.252.0 (et.7 during the second WAVE)

  !

  interface InlineGroup 1/1

  Shutdown

  !

  WCCP router-list 1 10.x.y.1

  WCCP promiscuity of tcp router-list-num 1 redirect l2 l2-back

  WCCP version 2

  When I do the following on the router:

  show ip wccp 61 detail

  or see the ip wccp 62 retail

  I see:

  The WCCP customer information:

  WCCP Client ID: 10.x.y.7

  Protocol Version: 2.0

  Status: usable

  Redirect: L2

  Package return: L2

  Assignment: HASH

  Initial hash Info: 00000000000000000000000000000000

  FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF

  Assigned hash of information: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF

  00000000000000000000000000000000

  Allocation of hash: 128 (50.00%)

  S/w redirected packets: 103912
  

  Connection time: 03:34:05

  GRE has bypassed the packages

  Process: 0

  CEF:                   0

  Errors: 0

  WCCP Client ID: 10.x.y.9

  Protocol Version: 2.0

  Status: usable

  Redirect: L2

  Package return: L2

  Assignment: HASH

  Initial hash of information: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF

  00000000000000000000000000000000

  Assigned to Hash Info: 00000000000000000000000000000000

  FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF

  Allocation of hash: 128 (50.00%)

  S/w redirected packets: 0
  

  Connection time: 01:46:24

  GRE has bypassed the packages

  Process: 0

  CEF:                   0

  Errors: 0

  On the WAAS, settings of assignment of WCCP for load balancing is the default: hash. (Hash on Source IP (Service, 61) :))

  the method of evacuation is IP forwarding

  I have multiple connections from different source IP addresses and somehow they all end up on the same WAE axe:

  ConnID Source IP: IP port: port Dest PeerID Accel RR

  360 10.x.y.3:49463 10.q.w.36:52732 XX TMDL 16.1%

  373 10.x.y.4:55005 10.q.w.36:52732 XX TMDL 24.8%

  I checked several places and read the best practices; support for router platform... and it seems that the config is OK

  http://www.Cisco.com/en/us/prod/collateral/contnetw/ps5680/ps6870/white_paper_c11-608042.html

  Any ideas?

  Thank you

  Patrick

  
  

  That question has been in the session 'ask the expert ':

  https://supportforums.Cisco.com/message/3482826

• Which device to use for the site to site VPN

  Hello

  Can someone recommend some inexpensive VPN devices, which will be set up to connect a few VPN site to site (20-30) (each site should not exceed 5 to 10 computers. The sites will be equipped with different VPN devices (like Linksys regular or any other - just able to site IPsec VPN). What I need is for my main site and hope get some suggestions.

  Thank you

  Ashok

  Hey Ashok

  Well, I'd say the firewall Cisco ASA 5500-x and Cisco ISR / ASR, two supported VPN from Site to Site on several sites.

  You can look into those if they meet your criteria.

  Concerning

  Véronique