Cisco PIX 501 to Cisco 3005 concentrator via remote access

Similar Questions

• ODA IP ASA when you browse the web via remote access vpn

  Hi all

  I was wondering if it is possible to configure an ASA5510 in a way to allow users remote access VPN use external IP of the ASA when browsing the web. So what I'm looking for is a solution to hide my IP address and use the IP address of the ASA, when browsing.

  The firmware version of the ASA is 9.1 (6)

  Thanks in advance

  Hello

  What you want to achieve is calles u-turn.

  You must enable the feature allowed same-security-traffic intra-interface

  For the configuration of the asa, here's the Cisco documentation (I don't copy paste on the post):

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...

  Thank you

  PS: Please do not forget to rate and score as good response if this solves your problem

• 1841 as Concentrator VPN remote access with manual keying

  Hi there and happy new year 2011 with best wishes!

  I would use a router 1841 as VPN hub for up to 20 remote connections.

  My remote (third party) clients have IPsec capacity supported by IKE and the Manual Keying, but I have not found information about simple configuration of Cisco VPN remote access (only on the easy VPN server).

  I'd like to configure the VPN entry Server Manual (I think it's an easy way to start), no problem to do?

  files:

  -topology

  -third party router Ethernet / 3G GUI IPsec with choice of algorithm auth

  -third party router Ethernet / 3G GUI IPsec with choice of encryption algorithm

  I feel so much better that someone help me!

  Kind regards

  Amaury

  As the remote end is third-party routers, the only option you have will be LAN-to-LAN IPSec VPN. You can not run VPN easy because that is only supported on Cisco devices.

  If your remote end has a static external ip address that ends the VPN, you can configure card crypto static LAN-to-LAN on the 1841 router, however, if your remote end has dynamic external ip address, you must configure card crypto dynamic LAN-to-LAN on the 1841 router. All remote LAN subnets must be unique.

• How to configure VPN 3000 Concentrator for remote access

  I have inherited a VPN concentrator and want to configure it to provide remote access to my internal laboratory network when I'm traveling.  Private interface is configured as 192.168.1.240/24.  Public interface is configured as one of my public IP addresses.  I have a public IP pool on the back side of a cable modem Roadrunner.  I created a pool of addresses for clients such as 192.168.1.200 by 192.168.1.205.  I created all group configurations, group and user base.

  In the IP Routing tab, I see a default route pointing to my IP address of public gateway - the IP address of my box of roadrunner cable modem gateway.

  Since my VPN client, I am able to connect to the VPN concentrator.  I get an address from the pool and check the details of the tunnel under the statistics section shows IP address correct pool for the customer and the correct public IP address of my VPN reorga

  Jeff,

  According to statistics, it seems that the client sends traffic to the hub, but his answer not get back.

  We need check the hub settings itself.

  I need check the hub settings and that it is a GUI based device so I can't even ask to see the technology and the only option available is to WebEx.

  You're ok with webex, pls lemme session comfortable time id and e-mail to send the invitation, it takes no more time and we will carry it out

  Thank you

  Ankur

• PIX 501 to allow access to the ftp server

  Hello

  We have a public ip address of the pix 501 and the other, I want to access the ftp server on the internal network from the outside. I tried to configure the PDM by a static nat, which translate to the address of the FTP to the public address, but then none of the stations networks could out - how can I configure it?

  I would also like to know what ports should I open on the acl for access to the ftp server.

  Thank you, daguech

  Yes, sorry... You must use the unique host for addresses command. The access list is applied to your external interface?

  for example, the command would be:

  Access-group acl_out in interface outside

  Also, can you connect to the local ftp server behind a firewall?

• Connectivity random Cisco Pix 501

  Hello. I'm having some trouble with my CISCO PIX 501 Setup.

  A few months I started having random disconnects on my network (from inside to outside). The machines can ping the DC or the Pix, but impossible to surf the internet. The only way to make them go outside is a reboot of Pix.

  My configuration is:

  -----------

  See the ACE - pix config (config) #.
  : Saved
  : Written by enable_15 at 09:23:07.033 UTC Tuesday, June 3, 2014
  6.3 (3) version PIX
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 8Ry34retyt7RR564 encrypted password
  2fvbbfgdI.2KUOU encrypted passwd
  hostname as pix
  domain as.local
  fixup protocol dns-length maximum 512
  fixup protocol esp-ike
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol pptp 1723
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list acl_out permit icmp any one
  ip access list acl_out permit a whole
  access-list acl_out permit tcp any one
  Allow Access-list outside_access_in esp a whole
  outside_access_in list access permit udp any eq isakmp everything
  outside_access_in list of access permit udp any eq 1701 all
  outside_access_in list of access permit udp any eq 4500 all
  outside_access_in ip access list allow a whole
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  outside 10.10.10.2 IP address 255.255.255.0
  IP address inside 192.168.100.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  history of PDM activate
  ARP timeout 14400
  Global 1 10.10.10.8 - 10.10.10.254 (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Access-group outside_access_in in interface outside
  access to the interface inside group acl_out
  Route outside 0.0.0.0 0.0.0.0 10.10.10.1 0
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  RADIUS Protocol RADIUS AAA server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.10.2 255.255.255.255 inside
  http 192.168.10.101 255.255.255.255 inside
  http 192.168.100.2 255.255.255.255 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  ISAKMP nat-traversal 20
  Telnet timeout 5
  SSH 192.168.10.101 255.255.255.255 inside
  SSH timeout 60
  Console timeout 0
  dhcpd dns 8.8.8.8 8.8.4.4
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  Terminal width 80
  Cryptochecksum:7f9bda5e534eaeb1328ab08a3c4d28a
  ------------

  Do you have any advice? I don't get what's wrong with my setup.

  My DC is 192.168.100.2 and the network mask is 255.255.255.0

  The network configuration is configured to set the IP of the gateway to 192.168.100.1 (i.e. the PIX 501).

  I have about 50 + peers on the internal network.

  Any help is apprecciate.

  Hello

  You have a license for 50 users +?

  After the release of - Show version

  RES

  Paul

• Microsoft secondary authority w / Cisco router / PIX 501

  I'm trying to get digital certificates to work on my 2621XM router. I have also

  need to put in place on the three firewalls PIX 501 but who have not obtained until now still. I have

  don't have no access to the CA root, but it could bring in line if I had to. I have

  have a stand-alone Microsoft subordinate CA that I want to use to publish all

  certificates.

  Is it possible, as well with the router and the firewall? If so, what version

  the IOS do I need? I installed the add-on CEP at HQ. I can't

  It works and I'm starting to wonder if it is still possible. If this doesn't

  work, how can I make it work? I have all the documents that Cisco has combed

  on the subject and have gotten nowhere.

  Any help would be greatly appreciated. Thank you.

  Jennnette,

  I sent this document, let me know how it goes or if you have any questions.

  Kurtis Durrett

• Cisco 3640 to the PIX 501 site 2 site VPN performance specifications.

  I intend on creating a site-2-site VPN in Star configuration with a Cisco 3640 as the hub and PIX 501 at the remote sites. My question is around the plug that I read.

  .

  The specifications for a PIX-501-BUN-K9 tell PIX 501 3DES Bundle (chassis, SW, 10 users, 3DES).

  .

  A question is what really "10 users. Which is the limit of the number of concurrent sessions, I have on the VPN at a given time, or that it means something else?

  .

  I also read the specs say that the Maximum number of VPN tunnels that can support a PIX 501 is 5. Because I'm not going to make a tunnel between the PIX 501 at the remote site and the 3640 on the central site, I think I would be OK. Is that correct or is the max value talk the maximum number of concurrent sessions on the tunnel tunnels?

  .

  Thank you.

  UDP traffic always creates a session in the PIX so that the return traffic will be allowed in. The UDP timeout is 2 minutes but IIRC. If you go around NAT with a statement of "nat 0" should not create an xlate I think.

  The real time is hard to say really, probably around 2 minutes for a UDP-only user, you would probably make a few 'local sho' orders on the PIX to really see for sure however.

• PIX 501 for Cisco 3640 VPN router

  -Start ciscomoderator note - the following message has been changed to remove potentially sensitive information. Please refrain from publishing confidential information about the site to reduce the risk to the security of your network. -end of the note ciscomoderator-

  Have a 501 PIX and Cisco 3640 router. The 3640 is configured for dynamic map for VPN. The PIX 501 is set to pointing to the 3640 router static map. I can establish a tunnel linking the PIX to the router and telnet to a machine AIX on the inside network to the router. When I try to print on the network of the PIX 501 inside it fails.

  What Miss me? I added the configuration for the PIX and the router.

  Here are the PIX config:

  PIX Version 6.1 (1)

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable encrypted password xxxxxxxxxxxxxxxx

  xxxxxxxxxxxxx encrypted passwd

  pixfirewall hostname

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 1720

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  names of

  pager lines 24

  interface ethernet0 10baset

  interface ethernet1 10full

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside dhcp setroute

  IP address inside 192.168.1.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  No sysopt route dnat

  Telnet timeout 5

  SSH timeout 5

  dhcpd address 192.168.1.2 - 192.168.1.33 inside

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:XXXXXXXXXXXXXXXXXXX

  : end

  Here is the router config

  Router #sh runn

  Building configuration...

  Current configuration: 6500 bytes

  !

  version 12.2

  no service button

  tcp KeepAlive-component snap-in service

  a tcp-KeepAlive-quick service

  horodateurs service debug datetime localtime

  Log service timestamps datetime localtime

  no password encryption service

  !

  router host name

  !

  start the flash slot1:c3640 - ik9o3s - mz.122 - 16.bin system

  queue logging limit 100

  activate the password xxxxxxxxxxxxxxxxx

  !

  clock TimeZone Central - 6

  clock summer-time recurring CENTRAL

  IP subnet zero

  no ip source route

  !

  !

  no ip domain-lookup

  !

  no ip bootp Server

  inspect the name smtp Internet IP

  inspect the name Internet ftp IP

  inspect the name Internet tftp IP

  inspect the IP udp Internet name

  inspect the tcp IP Internet name

  inspect the name DMZ smtp IP

  inspect the name ftp DMZ IP

  inspect the name DMZ tftp IP

  inspect the name DMZ udp IP

  inspect the name DMZ tcp IP

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 20

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key address x.x.180.133 xxxxxxxxxxx

  ISAKMP crypto keys xxxxxxxxxxx address 0.0.0.0 0.0.0.0

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac vpn test

  Crypto ipsec transform-set esp-3des esp-sha-hmac PIXRMT

  !

  dynamic-map crypto dny - Sai 25

  game of transformation-PIXRMT

  match static address PIX1

  !

  !

  static-card 10 map ipsec-isakmp crypto

  the value of x.x.180.133 peer

  the transform-set vpn-test value

  match static address of Hunt

  !

  map ISCMAP 15-isakmp ipsec crypto dynamic dny - isc

  !

  call the rsvp-sync

  !

  !

  !

  controller T1 0/0

  framing ESF

  linecode b8zs

  Slots 1-12 channels-group 0 64 speed

  Description controller to the remote frame relay

  !

  controller T1 0/1

  framing ESF

  linecode b8zs

  Timeslots 1-24 of channel-group 0 64 speed

  Description controller for internet link SBIS

  !

  interface Serial0/0:0

  Description CKT ID 14.HXGK.785129 Frame Relay to Remote Sites

  bandwidth 768

  no ip address

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  encapsulation frame-relay

  frame-relay lmi-type ansi

  !

  interface Serial0 / point to point 0:0.17

  Description Frame Relay to xxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 17 frame relay interface

  !

  interface Serial0 / point to point 0:0.18

  Description Frame Relay to xxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 18 frame relay interface

  !

  interface Serial0 / point to point 0:0.19

  Description Frame Relay to xxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 19 frame relay interface

  !

  interface Serial0 / point to point 0:0.20

  Description Frame Relay to xxxxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 20 frame relay interface

  !

  interface Serial0 / point to point 0:0.21

  Description Frame Relay to xxxxxxxxxxxx

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 21 frame relay interface

  !

  interface Serial0 / point to point 0:0.101

  Description Frame Relay to xxxxxxxxxxx

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 101 frame relay interface

  !

  interface Serial0/1:0

  CKT ID 14.HCGS.785383 T1 to ITT description

  bandwidth 1536

  IP address x.x.76.14 255.255.255.252

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  NAT outside IP

  inspect the Internet IP on

  no ip route cache

  card crypto ISCMAP

  !

  interface Ethernet1/0

  IP 10.1.1.1 255.255.0.0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  no ip route cache

  no ip mroute-cache

  Half duplex

  !

  interface Ethernet2/0

  IP 10.100.1.1 255.255.0.0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  no ip route cache

  no ip mroute-cache

  Half duplex

  !

  router RIP

  10.0.0.0 network

  network 192.168.1.0

  !

  IP nat inside source list 112 interface Serial0/1: 0 overload

  IP nat inside source static tcp 10.1.3.4 443 209.184.71.138 443 extensible

  IP nat inside source static tcp 10.1.3.4 9869 209.184.71.138 9869 extensible

  IP nat inside source 10.1.3.2 static 209.184.71.140

  IP nat inside source static 10.1.3.6 209.184.71.139

  IP nat inside source static 10.1.3.8 209.184.71.136

  IP nat inside source static tcp 10.1.3.10 80 209.184.71.137 80 extensible

  IP classless

  IP route 0.0.0.0 0.0.0.0 x.x.76.13

  IP route 10.2.0.0 255.255.0.0 Serial0 / 0:0.19

  IP route 10.3.0.0 255.255.0.0 Serial0 / 0:0.18

  IP route 10.4.0.0 255.255.0.0 Serial0 / 0:0.17

  IP route 10.5.0.0 255.255.0.0 Serial0 / 0:0.20

  IP route 10.6.0.0 255.255.0.0 Serial0 / 0:0.21

  IP route 10.7.0.0 255.255.0.0 Serial0 / 0:0.101

  no ip address of the http server

  !

  !

  PIX1 static extended IP access list

  IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255

  IP access-list extended hunting-static

  IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255

  extended IP access vpn-static list

  ip permit 192.168.1.0 0.0.0.255 10.1.0.0 0.0.255.255

  IP 192.0.0.0 allow 0.255.255.255 10.1.0.0 0.0.255.255

  access-list 1 refuse 10.0.0.0 0.255.255.255

  access-list 1 permit one

  access-list 12 refuse 10.1.3.2

  access-list 12 allow 10.1.0.0 0.0.255.255

  access-list 12 allow 10.2.0.0 0.0.255.255

  access-list 12 allow 10.3.0.0 0.0.255.255

  access-list 12 allow 10.4.0.0 0.0.255.255

  access-list 12 allow 10.5.0.0 0.0.255.255

  access-list 12 allow 10.6.0.0 0.0.255.255

  access-list 12 allow 10.7.0.0 0.0.255.255

  access-list 112 deny ip host 10.1.3.2 everything

  access-list 112 refuse ip 10.1.0.0 0.0.255.255 192.168.1.0 0.0.0.255

  access-list 112 allow ip 10.1.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.2.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.3.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.4.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.5.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.6.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.7.0.0 0.0.255.255 everything

  access-list 120 allow ip host 10.100.1.10 10.1.3.7

  not run cdp

  !

  Dial-peer cor custom

  !

  !

  !

  !

  connection of the banner ^ CCC

  ******************************************************************

  WARNING - Unauthorized USE strictly PROHIBITED!

  ******************************************************************

  ^ C

  !

  Line con 0

  line to 0

  password xxxxxxxxxxxx

  local connection

  Modem InOut

  StopBits 1

  FlowControl hardware

  line vty 0 4

  exec-timeout 15 0

  password xxxxxxxxxxxxxx

  opening of session

  !

  end

  Router #.

  Add the following to the PIX:

  > permitted connection ipsec sysopt

  This indicates the PIX around all ACLs for IPsec traffic. Now that your IPSec traffic is still subject to the standard rules of PIX, so launched inside the traffic is allowed to go in, but off-initiated traffic is not.

• VPN between cisco unified customer 3.6.3 and Pix 501 6.2 (1) with the MS CA server

  Hello

  I have Microsoft CA server with the latest support CEP and pix 501 that gets the digital certificate. I also have the client certificate of Cisco, but VPN doesn't work

  In the IPSec Log Viewer, I constantly "CM_IKE_ESTABLISH_FAIL."

  It worked well prior to Win2k server has been completely updated with the latest patches.

  The pix configuration is identical to that of article http://www.cisco.com/warp/public/471/configipsecsmart.html

  I reinstall the stand-alone CA and support CEP server but not had any luck.

  What could be wrong?

  It looks like IKE implementation problem. Make DH group 2 policy ISAKMP.

  Visit this link:

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_v53/IPSec/exvpncl.htm

• QoS is supported on the Cisco PIX 501 or 506th?

  Hello

  There is no mention of QoS in technical for the PIX 501 and 506 records but nothing for the 515. PIX OS 7.x configuration guides do not mention specific material support.

  Does anyone know if QoS is taken care of in the 501 or 506th - I need support lines expectations for VoIP over IPSec.

  Thank you

  Chris

  QoS is supported in 7.x code, you would have to level 501/506 to 7.x code, but this is not supported on these two models, the next logical solution would be to upgrade your PIX 501/506 to asa5505s.

  Rgds

  Jorge

• Customer Cisco PIX 501 VPN connects but no connection to the local network

  Hi all:

  I am able to make a VPN connection to a PIX 501. The remote client is assigned an IP (192.168.2.1) also, but not able to access all the machines in the local network connected to the PIX.

  I have attached the PIX configuration.

  Advice will be greatly appreciated.

  ********************

  6.3 (5) PIX version

  interface ethernet0 car

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable password xxxx

  passwd xxxxx

  pixfirewall hostname

  domain ciscopix.com

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  access-list 102 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside dhcp setroute

  IP address inside 192.168.1.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool ippool 192.168.2.1 - 192.168.2.5

  location of PDM 192.168.2.0 255.255.255.0 outside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) - 0 102 access list

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  ISAKMP allows outside

  ISAKMP identity address

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup vpn3000 ippool address pool

  vpngroup vpn3000 Server dns 68.87.72.130

  vpngroup vpn3000-wins 192.168.1.100 Server

  vpngroup vpn3000 split tunnel 101

  vpngroup vpn3000 downtime 1800

  password vpngroup vpn3000 *.

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd address 192.168.1.2 - 192.168.1.33 inside

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:xxxx

  ****************

  The DNS server is the one assigned to me by my ISP.

  My internal network connected to the PIX is 192.168.1.1 - 192.168.1.33 and the VPN ip pool is 192.168.2.1 - 192.168.2.5

  "isakmp nat-traversal 20" can do the trick.

• PIX 501, 1 static IP, IP address dynamic 2. Mesh full possible?

  I have 3 sites. All sites have PIX 501. Central site has a static IP, 2 remote sites a dynamic IP.

  I have no problem with the connection to the central site by using their dynamic IP address in a remote star connection.

  Is it possible for 2 remote sites communicate? There is data that must be transferred between remote sites. I read somewhere in cisco site web which its possible via mesh on request.

  Does anyone have an example of configuration on a VPN Site to Site where the Central site has static IP and remote sites with a dynamic IP? Remote locations teaches a dynamic IP from remote sites to the central server.

  Thank you.

  With IOS as your hub and then the Yes rays, the rays can learn dynamically address other departments using the PNDH. This type of configuration is called Dynamic Multipoint VPN (DMVPN), you can read everything you need to know about this here:

  http://www.Cisco.com/warp/public/105/DMVPN.html

  Even with EzVPN (not DMVPN) the rays will not learn the address of other rays, all communication is always via the hub. Call another talks would work, but as I said, the packages will talk-star.

• L2l IPSec VPN 3000 and PIX 501

  Hello

  I have a remote site that has a broadband internet connection and uses a PIX 501.  We wanted to connect them with our main office using our VPN 3000 via VPN site-to-site.

  I followed the following documentation:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml#tshoot

  However the L2L session does not appear on the hub when I check the active sessions.

  The network diagram, as well as the PIX config and the screenshots of the VPN configuration for the IPSec-L2L tunnel is attached.

  Any help or advice are appreciated.

  I just noticed that the PIX firewall, the phase 1 paramateres are not configured. You must configure the same PASE 1 and phase 2 settings on both ends of the tunnel.

  For example, on CVPN 3000, you have configured settings Phase 1 as 3DES, pre-shared key etc... We have the same configuration on the PIX firewall too.

  Here is an example of sample config

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml

  I hope this helps!

• Pix 501 connection problems

  I am very new to cisco equipment and I was wondering if someone could help me with this (probably very simple question).

  When connecting to my pix via the browser (https://192.168.1.1/startup.html), the browser never took the start screen with the message that says "loading, please wait." This leads me to believe that the firewall is rejecting connections from my machine (which uses dhcp to get an ip address of the pix).

  To work around this problem, I tried to connect to the CLI using hyperterminal. I can connect and run a few basic commands as 'show version', but cannot log on as a user with permissions.

  If the web interface has a default connection of void & empty, surely the cli should be the same?

  Is anyone able to tell me what is the default login, so that I can start confguring the pix via the cli?

  Thanks in advance.

  Justin Spencer.

  Please see below for info pix:

  Cisco PIX Firewall Version 6.3 (3)

  Cisco PIX Device Manager Version 3.0 (1)

  Updated Thursday, August 13 03 13:55 by Manu

  pixfirewall until 12 minutes 18 seconds

  Material: PIX - 501, 16 MB RAM, 133 MHz Am5x86 CPU

  Flash E28F640J3 @ 0 x 3000000, 8 MB

  BIOS Flash E28F640J3 @ 0xfffd8000, 128KB

  0: ethernet0: the address is 0011.937e.0486, irq 9

  1: ethernet1: the address is 0011.937e.0487, irq 10

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  The maximum physical Interfaces: 2

  Maximum Interfaces: 2

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal guests: 10

  Throughput: unlimited

  Peer IKE: 10

  This PIX has a restricted license (R).

  Serial number: 808301473 (0x302db3a1)

  Activation key running: 0xb53be54d 0x26da18f9 0xb2b78cef 0x8fe1abb6

  Configuration changed from enable_1 to 15:36:42.554 UTC, Monday, November 8, 2004

  pixfirewall >

  long live java.

  Please this mark as resolved, others won't waste time.

  Thank you