Cisco's VPN IPSec help please

Similar Questions

• Cisco's VPN IPSec client for LAN connectivity

  I've looked through further discussions and were not able to find a clear answer on this, so I apologize if this is a duplicate question.

  I have the client setup Cisco VPN on an ASA 5505 with tunneling split. I can connect to the VPN very well. I can access the internet fine. I can't get the LAN, however. I try to do a ping, telnet, rdp, etc devices on the side LAN of the firewall without a bit of luck. I have torn down and configure the VPN several times via the CLI and I even used various configurations by using the wizard, all this without a bit of luck. Any help would be appreciated.

  ASA Version 8.2 (2)

  !

  hostname spp-provo-001-fwl-001

  domain servpro.local

  activate the F7n9M1BQr1HPy/zu encrypted password

  F7n9M1BQr1HPy/zu encrypted passwd

  no names

  name 10.0.0.11 Exch-Srv

  name 10.0.0.12 DRAC

  name 10.0.0.10 DVR

  !

  interface Vlan1

  nameif inside

  security-level 100

  the IP 10.0.0.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  ServPro PPPoE client vpdn group

  IP address pppoe setroute

  !

  interface Vlan12

  nameif Guest_Wireless

  security-level 90

  IP 10.10.0.1 address 255.255.255.0

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  switchport access vlan 12

  !

  exec banner * only authorized access *.

  exec banner * this system is the property of ServPro. Unplug IMMEDIATELY that you are not an authorized user. *

  connection of the banner * only authorized access *.

  connection of the banner * this system is the property of ServPro. Unplug IMMEDIATELY that you are not an authorized user. *

  banner asdm * only authorized access *.

  banner asdm * this system is the property of ServPro. Unplug IMMEDIATELY that you are not an authorized user. *

  boot system Disk0: / asa822 - k8.bin

  passive FTP mode

  clock timezone STD - 7

  clock to summer time recurring MDT

  DNS lookup field inside

  DNS server-group DefaultDNS

  10.0.0.11 server name

  Name-Server 8.8.8.8

  domain servpro.local

  DRACServices tcp service object-group

  EQ port 5900 object

  EQ object of the https port

  EQ object Port 5901

  object-group service Exch-SrvServices tcp

  EQ port 587 object

  port-object eq 993

  port-object eq www

  EQ object of the https port

  port-object eq imap4

  EQ Port pop3 object

  EQ smtp port object

  SBS1Services tcp service object-group

  EQ port 3389 object

  port-object eq www

  EQ object of the https port

  EQ smtp port object

  outside_access_in list extended access permit tcp any host *. *. *. * object-group SrvServices Exch

  outside_access_in list permits all icmp access *. *. *. * 255.255.255.248

  capture a whole list of access allowed icmp

  Servpro_splitTunnelAcl list standard access allowed 10.0.0.0 255.255.255.0

  inside_nat0_outbound to access ip 10.0.0.0 scope list allow 255.255.255.0 172.16.10.0 255.255.255.240

  inside_nat0_outbound list of allowed ip extended access any 172.16.10.0 255.255.255.240

  guest_wireless_in list extended access permitted tcp a whole

  guest_wireless_in of access allowed any ip an extended list

  NO_NAT to access ip 10.0.0.0 scope list allow 255.255.255.0 10.10.0.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  MTU 1500 Guest_Wireless

  mask 172.16.10.1 - 172.16.10.14 255.255.255.240 IP local pool ServProDHCPVPN

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 625.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT-control

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  NAT (Guest_Wireless) 1 0.0.0.0 0.0.0.0

  static (inside, outside) *. *. *. * 10.0.0.11 netmask 255.255.255.255

  Access-group outside_access_in in interface outside

  Access-group guest_wireless_in in the Guest_Wireless interface

  Route outside 0.0.0.0 0.0.0.0 *. *. *. * 2 track 2

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA-server Exch-Srv Protocol nt

  AAA-server Exch-Srv (inside) host 10.0.0.11

  Timeout 5

  auth-NT-PDC SRV EXCH

  the ssh LOCAL console AAA authentication

  AAA authentication LOCAL telnet console

  AAA authentication http LOCAL console

  LOCAL AAA authentication serial console

  Enable http server

  http server idle-timeout 10

  http 10.0.0.0 255.255.255.0 inside

  http 0.0.0.0 0.0.0.0 outdoors

  redirect http outside 80

  redirect http inside 80

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  monitor SLA 124

  type echo protocol ipIcmpEcho 4.2.2.2 outside interface

  NUM-package of 3

  frequency 10

  Annex monitor SLA 124 life never start-time now

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  registration auto

  name of the object CN = cisco.spprovo.com

  ServPro key pair

  Configure CRL

  string encryption ca ASDM_TrustPoint0 certificates

  certificate f642be4b

  308202fc 308201e4 a0030201 020204f6 42be4b30 0d06092a 864886f7 0d 010105

  311a 3018 05003040 06035504 03131163 6973636f 2e737070 726f766f 2e636f6d

  31223020 06092 has 86 01090216 13636973 636f2e73 726f2e6c 65727670 4886f70d

  6f63616c 31303034 30383230 35363232 30303430 35323035 5a170d32 301e170d

  3632325a 3040311a 30180603 55040313 and 11636973 636f2e73 7070726f 766f2e63

  6f6d3122 30200609 2a 864886 f70d0109 02161363 6973636f 2e736572 7670726f

  2e6c6f63 616c 3082 0122300d 06092 has 86 01010105 00038201 0f003082 4886f70d

  010a 0282 010100 has 5 b4646cde f981f048 efa54c8a 4ba4f51c 25471e01 459ea905

  313ef490 72b4d853 4e95ab7d a8c1350e 5728dca6 a98c439e 2c12d219 06ee7209

  9f2584d1 b2abf71c 31c0890f 3098533b 6bc3ad4b 3bcd8986 e70ca78e 07a749d6

  ee4e0892 4fcb79b6 724f7012 9f42fc2f b80c17ed adb5d36b 67590061 453d9ae6

  16583d 36 5a22b7c2 737fd705 94656f3f 578fb67f 79bd2a59 17522be3 d2386e22

  2c62352f cda317b0 be805a04 76f19989 34031cbd a5fc62a7 1d9f52f3 00cf60b6

  bbbdc4f0 fb651b82 b3e22a0a 718ff0b4 e213f4ac cdeb413b 9c4a47c3 9134d7a9

  e8dcf2c5 c1cd4075 61d75e3a 475a17f1 2f955741 9ed2a8d6 c381eba3 247134e1

  b5c33fac 7ae03d02 03010001 300 d 0609 2a 864886 05050003 82010100 f70d0101

  156 5fde62c5 b4cbb0f4 0c61fab7 fae04399 27457ab7 9790c 3fac914d 70595db9

  e69d3f19 3476dc51 32c885de b5904030 05624fe0 e8983e0a ab5527f3 8c5dd64a

  1e1a6082 b6091657 8704c 539 a3c6be47 da2a871f 4fafe668 70db2c2b 573d47b2

  7f3df02f c9d53a92 bcf5f518 9953e14c f957a6ca 279f9e9f ddbd2561 6e0503c2

  ba59a165 055d697f dd028d00 5cc288c4 83ced827 9c82ef3e 7e67f2d2 6de573e3

  42a0b6bf ef8d06ed cb9805f2 c38011d3 5263bc3f 5b68df7a bef36c40 8c5e33f3

  26b02c27 63a9848c 8461738f cd19ae95 f059ee34 afe4bdbc 8d8d2335 751b 0621

  65464b2c 4649779d 3ba01b69 8977 has 790 73815f8b 3c483f93 a5ca9685 04b6e18a

  quit smoking

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  No encryption isakmp nat-traversal

  !

  Track 2 rtr 124 accessibility

  Telnet 10.0.0.0 255.255.255.0 inside

  Telnet timeout 10

  SSH 10.0.0.0 255.255.255.0 inside

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH timeout 10

  SSH version 2

  Console timeout 10

  VPDN group ServPro request dialout pppoe

  VPDN group ServPro localname *

  VPDN group ServPro ppp authentication pap

  password username * VPDN * local store

  dhcpd outside auto_config

  !

  dhcpd address 10.10.0.100 - 10.10.0.227 Guest_Wireless

  dhcpd dns 8.8.8.8 4.2.2.2 interface Guest_Wireless

  enable Guest_Wireless dhcpd

  !

  a basic threat threat detection

  threat detection statistics

  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200

  NTP server 38.117.195.101 source outdoors

  NTP server 72.18.205.157 prefer external source

  SSL-trust outside ASDM_TrustPoint0 point

  WebVPN

  allow outside

  SVC disk0:/anyconnect-win-2.3.0254-k9.pkg 1 image

  enable SVC

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

  Servpro internal group policy

  Group Policy attributes Servpro

  Server DNS 10.0.0.11 value

  Protocol-tunnel-VPN IPSec svc webvpn

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list Servpro_splitTunnelAcl

  SERVPRO.local value by default-field

  servpro encrypted NtdaWcySmet6H6T0 privilege 15 password username

  servpro username attributes

  type of service admin

  username, encrypted bHGJDrPmHaAZY/78 Integratechs password

  tunnel-group Servpro type remote access

  attributes global-tunnel-group Servpro

  address pool ServProDHCPVPN

  authentication-server-group LOCAL Exch-Srv

  strategy-group-by default Servpro

  tunnel-group Servpro webvpn-attributes

  enable ServPro group-alias

  IPSec-attributes tunnel-group Servpro

  pre-shared key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:52bca254012b1b05cca7dfaa30d1c42a

  : end

  Most likely you are behind a router PAT when you are connected to the VPN, so please allow the following:

  Crypto isakmp nat-traversal 30

• Setup for use with Cisco Anyconnect VPN IPsec

  So, I had trouble setting up VPN on our ASA 5510. I would use IPsec VPN so that we don't have to worry about licensing issues, but what I have read you can do with and always use Cisco Anyconnect. My knowledge on how to set up VPN especially in iOS version 8.4 is limited, so I've been using a combination of command line and ASDM.

  I am finally able to connect from a remote location, but once I log in, nothing else works. What I've read, you can use IPsec for client-to-lan connections. I use a pre-shared for this. Documentation is limited on what should happen after have connected you? Shouldn't be able to local access on the vpn connection computers? I'm trying to implement work. If I have VPN from home, should not be able to access all of the resources at work? According to me, because I used the command-line as ASDM I confused some of the configuration. In addition, I think that some of the default policies are confused me too. So I probably need a lot of help. Here is my current setup with the changed IP address and other things that are not related to deleted VPN.

  NOTE: We are still testing this ASA and is not in production.

  Any help you can give me is greatly appreciated.

  ASA Version 8.4 (2)

  !

  ASA host name

  domain.com domain name

  !

  interface Ethernet0/0

  nameif inside

  security-level 100

  the IP 192.168.0.1 255.255.255.0

  !

  interface Ethernet0/1

  nameif outside

  security-level 0

  IP 50.1.1.225 255.255.255.0

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  No nameif

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  boot system Disk0: / asa842 - k8.bin

  passive FTP mode

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  !

  permit same-security-traffic intra-interface

  !

  network of the NETWORK_OBJ_192.168.0.224_27 object

  subnet 192.168.0.224 255.255.255.224

  !

  object-group service VPN

  ESP service object

  the purpose of the tcp destination eq ssh service

  the purpose of the tcp destination eq https service

  the purpose of the service udp destination eq 443

  the destination eq isakmp udp service object

  !

  allowed IP extended ip access list a whole

  !

  mask 192.168.0.225 - 192.168.0.250 255.255.255.0 IP local pool VPNPool

  no failover

  failover time-out period - 1

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 645.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.0.224_27 NETWORK_OBJ_192.168.0.224_27 non-proxy-arp-search to itinerary

  !

  the object of the LAN network

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_in in external interface

  Route outside 0.0.0.0 0.0.0.0 50.1.1.250 1

  Sysopt noproxyarp inside

  Sysopt noproxyarp outdoors

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec ikev2 ipsec-proposal OF

  encryption protocol esp

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 proposal ipsec 3DES

  Esp 3des encryption protocol

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal AES

  Esp aes encryption protocol

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal AES192

  Protocol esp encryption aes-192

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 AES256 ipsec-proposal

  Protocol esp encryption aes-256

  Esp integrity sha - 1, md5 Protocol

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  registration auto

  name of the object CN = ASA

  Configure CRL

  crypto ca server

  Shutdown

  string encryption ca ASDM_TrustPoint0 certificates

  certificate d2c18c4e

  864886f7 0d06092a c18c4e30 308201f3 3082015c a0030201 d 020204 2 0d 010105

  0500303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609

  02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109

  3131 31303036 31393133 31365a 17 323131 30303331 39313331 0d 170d 6f6d301e

  365a303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609

  02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109

  6f6d3081 9f300d06 092 has 8648 86f70d01 01010500 03818d b 30818902-00-818100-2

  8acbe1f4 5aa19dc5 d3379bf0 f0e1177d 79b2b7cf cc6b4623 d1d97d4c 53c9643b

  37f32caf b13b5205 d24457f2 b5d674cb 399f86d0 e6c3335f 031d54f4 d6ca246c

  234b32b2 b3ad2bf6 e3f824c0 95bada06 f5173ad2 329c28f8 20daaccf 04c 51782

  3ca319d0 d5d415ca 36a9eaff f9a7cf9c f7d5e6cc 5f7a3412 98e71de8 37150f02

  03010001 300 d 0609 2a 864886 f70d0101 05050003 8181009d d2d4228d 381112a 1

  cfd05ec1 0f51a828 0748172e 3ff7b480 26c197f5 fd07dd49 01cd9db6 9152c4dc

  18d0f452 50f5d0f5 4a8279c4 4c1505f9 f5e691cc 59173dd1 7b86de4f 4e804ac6

  beb342d1 f2db1d1f 878bb086 981536cf f4094dbf 36c5371f e1a0db0a 75685bef

  af72e31f a1c4a892 d0acc618 888b53d1 9b 888669 70e398

  quit smoking

  IKEv2 crypto policy 1

  aes-256 encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 10

  aes-192 encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 20

  aes encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 30

  3des encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 40

  the Encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  Crypto ikev2 activate out of service the customer port 443

  Crypto ikev2 access remote trustpoint ASDM_TrustPoint0

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 10

  Console timeout 0

  management-access inside

  SSL-trust outside ASDM_TrustPoint0 point

  WebVPN

  allow outside

  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

  AnyConnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 2

  AnyConnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 3

  profiles of AnyConnect VPN disk0: / devpn.xml

  AnyConnect enable

  tunnel-group-list activate

  internal VPN group policy

  attributes of VPN group policy

  value of server WINS 50.1.1.17 50.1.1.18

  value of 50.1.1.17 DNS server 50.1.1.18

  Ikev1 VPN-tunnel-Protocol, l2tp ipsec ikev2 ssl-client

  digitalextremes.com value by default-field

  WebVPN

  value of AnyConnect VPN type user profiles

  always-on-vpn-profile setting

  privilege of xxxxxxxxx encrypted password username administrator 15

  VPN1 xxxxxxxxx encrypted password username

  VPN Tunnel-group type remote access

  General-attributes of VPN Tunnel-group

  address (inside) VPNPool pool

  address pool VPNPool

  LOCAL authority-server-group

  Group Policy - by default-VPN

  VPN Tunnel-group webvpn-attributes

  enable VPN group-alias

  Group-tunnel VPN ipsec-attributes

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  class-map ips

  corresponds to the IP access list

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  inspect the http

  class ips

  IPS inline help

  class class by default

  Statistical accounting of user

  I would recommend buy AnyConnect Essentials. The cost of the license is nominal - list of US $150 for the 5510. (piece number L-ASA-AC-E-5510 =)

  Meawwhile you can use the Cisco VPN client inherited with IKEv1 IPSec remote access VPN using profiles *.pcf.

  I believe you can also use the client Anyconnect client SSL or DTLS transport access remotely (non-IPsec) without having to buy the license Anyconnect Essentials for your ASA focus.

  As an aside, note that if you want to use AnyConnect Mobile (e.g. for iPhone, iPad, Android, Blackberry etc.clients) you will also get the additional license for it (L-ASA-AC-M-5510 =, also price US $150)

• double authentication with Cisco's VPN IPSEC client

  Cisco VPN client (the legacy IPSEC client) does support dual authentication with RSA token AND ActiveDirectory credentials?

  I know that AnyConnect supports it and the commandsecondary- authentication -Server- group' is only for ssl connections, but must be confirmed.

  Kind regards

  Mohammad

  Hi Mohammad,.

  What is double authentication support for Cisco VPN Client?

  A. No. Double authentication only is not supported on the Cisco VPN Client.

  You can find more information on the customer Cisco VPN here.

  As you said the only client that supports dual authentication is the Cisco AnyConnect secure mobility Client.

  Please note and mark it as correct this Post!

  Let me know if there are still questions about it!

  David Castro,

• License of Cisco 2821 VPN IpSEC

  Hello

  I have a small problem, a do give me a Cisco 2821 for installing a VPN client to a small local network.

  I don't have problem to the router connection, but when I try to set up an ipsec i cant.

  We have need of a license or a module installation IpSe VPN?

  When I run this command, the router does not include:

  vpnbog1 (config) #crypto isakmp policy 1

  ^

  Invalid entry % detected at ' ^' marker.

  vpnbog1 (config) #.

  the show version is:

  January 3, 21:12:49.219: % SYS-5-CONFIG_I: configured from console by admin on consoleversion

  Software (fc2) SOFTWARE VERSION, Cisco IOS, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4 (3i)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 1986-2007 by Cisco Systems, Inc.

  Updated Thursday 28 November 07 21:09 by stshen

  ROM: System Bootstrap, Version 12.4 (13r) T, RELEASE SOFTWARE (fc1)

  vpnbog1 uptime is 1 hour, 32 minutes

  System to regain the power ROM

  System restarted at 14:40:43 PCTime Friday January 3, 2014

  System image file is "flash: c2800nm-spservicesk9 - mz.124 - 3i.bin".

  This product contains cryptographic features and is under the United States

  States and local laws governing the import, export, transfer and

  use. Delivery of Cisco cryptographic products does not imply

  third party approval to import, export, distribute or use encryption.

  Importers, exporters, distributors and users are responsible for

  compliance with U.S. laws and local countries. By using this product you

  agree to comply with the regulations and laws in force. If you are unable

  to satisfy the United States and local laws, return the product.

  A summary of U.S. laws governing Cisco cryptographic products to:

  http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html

  If you need assistance please contact us by mail at

  [email protected] / * /.

  Cisco 2821 (revision 53.51) with 251904 K/K 10240 bytes of memory.

  Card processor ID FTX1213A06Y

  2 gigabit Ethernet interfaces

  2 FXS voice interfaces

  Configuration of DRAM is wide with parity 64-bit capable.

  239K bytes of non-volatile configuration memory.

  62720K bytes of ATA CompactFlash (read/write)

  You are tuning a "spservices" image that has no crypto code compiled (AFAIR, feel free to doublecheck).

  You would need advanced security or advanced IP services have together.

  http://www.Cisco.com/en/us/prod/collateral/routers/ps5853/images/0900aecd80524a07_null_null_null_07_19_05-1.jpg

  M.

• need help with VPN IPSEC with RV042

  https://supportforums.Cisco.com/docs/doc-30883

  I enjoy any support for a trial with RV042 VPN IPSec game please.

  Thanks in advance.

  Hi Bay, if you use a Windows computer, you can use QuickVPN. The only thing to note is the router that you have as the gateway to the RV042. You must define a port forward for all IPsec services be able to overcome the problems with the NAT device.

  RV042 configuration is easy, create a name of user and password and that's it. The problem/challenge will get your NAT connection to allow VPN pass.

  -Tom
  Please mark replied messages useful

• Help, please! Microsoft Vs Cisco VPN Client VPN

  Could someone please indicate if the Cisco VPN Client is safer than the VPN integrated Microsoft on windows XP? If the Cisco client is more secure than why? Microsoft it does not use IPSEC and PPTP right?

  Please advise - very urgent!

  I don't know a customer Cisco Cisco VPN concentrator is safer, but I'm not sure exactly why.

  Carlton,

  Take a deeper look at the same time, all your questions will be answered once you look at these links.

  IPSec is a Cisco VPN standard, open customer or any customer VPN IPSec based should meet these standards. You'll learn more by reading these few bellow of links at the end of the reading you will be to have a better

  perspective on the customer you would gear more to use as a professional network.

  Personally, I've been away little by little PPTP and substituting Cisco VPN clients. Don't get me wrong, PPTP is still widely used there, but it is more vulnerable.

  With Ipsec VPN, you have a wider choice of authentication algorithms, to base

  granularity of ciphers as a way to implement a secure VPN extreamely for RA architecture

  Introduction to IPsec

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_tech_note09186a0080094203.shtml

  Introduction to PPTP/L2TP

  http://www.Clavister.com/manuals/ver8.6x/manual/VPN/pptp_basics.htm

  Analysis of vulnerabilities and implementation MS PPTP

  http://www.Schneier.com/paper-PPTP.html

  http://www.Schneier.com/paper-PPTP.PDF

  Alternative workaround to use client MS using L2TP over Ipsec

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00807213a7.shtml

  In addition, you can do a google search on "hacking PPTP" or "Ipsec" to preview more vulnerabilities.

  Rgds

  Jorge

• Cisco Anyconnect VPN vs IPSec AnyConnect SSL

  Hello

  Can someone tell me what is the difference between the Anyconnect SSL VPN and Anyconnect VPN IPSec.

  When we use one and not the other?

  Thank you very much.

  Best regards.

  Hello Abdollah,

  AnyConnect based on the SSL protocol is called Anyconnect SSL VPN and if you deploy Anyconnect with the IPSec protocol, it is called IKev2.

  AnyConnect (via IKEv2 or SSLVPN) does not use a pre shared key to authenticate the user.  A certificate will be used to authenticate the user and the ASA of + pass and the certificate used to authenticate the user.  The XML profile is necessary just to use the Anyconnect IKEv2 client rather than the default of SSL when connecting to the ASA.

  Here is the doc announced some of the benefits of using Anyconnect with Ikev2 rather than SSL VPN.
  http://www.Cisco.com/en/us/docs/iOS-XML/iOS/sec_conn_ike2vpn/configuration/15-2mt/sec-cfg-IKEv2-Flex.html#GUID-6548042E-1E4C-416A-8347-00DCF96F04DF

  In essence, if you have a simple deployment, then you can go with the installation of SSL VPN and if you want to take advantage of additional features, you can use Anyconnect with IPSec.

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• Help, please! Connected to the VPN, but cannot access internal servers.

  Hi friends,

  I'm a newbie on vpn stuff, I set up a base on a Cisco ASA 5505 vpn by using ASDM, and I was able to connect to it.  However, I can't ssh or RDP to one of the servers in the House after that I connected to the vpn.  Here is the configuration.  Help, please!

  ASA Version 8.2 (5)

  !

  hostname sc - asa

  domain abc.com

  enable the encrypted password xxxxxxxxx

  xxxxxxxxx encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain OpenDNS.com

  sc-pool_splitTunnelAcl-list of allowed access standard 192.168.1.0 255.255.255.0

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.1.96 255.255.255.240

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool sc-192.168.1.100 - 192.168.1.110 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  interface ID client DHCP-client to the outside

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.5 - 192.168.1.36 inside

  dhcpd dns 208.67.222.222 208.67.220.220 interface inside

  rental contract interface 86400 dhcpd inside

  dhcpd abc.com domain inside interface

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  SSL encryption rc4 - md5, rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1

  WebVPN

  abc group policy - sc internal

  attributes of the strategy of group abc - sc

  value of server DNS 208.67.222.222 192.168.1.3

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value abc-sc_splitTunnelAcl

  field default value abc.com

  a001 xxxxxxxxxxx encrypted password username

  a002 xxxxxxxxxxx encrypted password username

  username a003 encrypted password privilege 0 xxxxxxxxxxx

  a003 username attributes

  Strategy Group-VPN-abc-sc

  a004 xxxxxxxxxxx encrypted password privilege 0 username

  a004 username attributes

  Strategy Group-VPN-abc-sc

  a005 xxxxxxxxxxx encrypted password username

  a006 xxxxxxxxxxx encrypted password username

  username privilege 15 encrypted password xxxxxxxxxxx a007

  remote access to tunnel-group abc - sc type

  attributes global-tunnel-group-abc - sc

  address sc-pool pool

  Group Policy - by default-abc-sc

  tunnel-group abc - sc ipsec-attributes

  pre-shared key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:e7df4fa4b60a252d806ca5222d48883b

  : end

  Hello

  I would suggest you start by changing the pool VPN to something else than the current LAN network and see if that helps

  These should be the configuration required to achieve this goal

  • First remove us pool setup VPN VPN
  • Then we delete the VPN Pool and create again with an another address space
  • When then attach this new Pool of VPN again to the VPN configuration
  • In the last step, we add a NAT0 / exempt for this new pool VPN NAT configuration and remove the old ACL line for the former group of VPN

  attributes global-tunnel-group-abc - sc

  no address-sc-swimming pool

  no ip local pool sc 192.168.1.100 - 192.168.1.110 mask 255.255.255.0

  IP local pool sc-192.168.100.100 - 192.168.100.110 mask 255.255.255.0

  attributes global-tunnel-group-abc - sc

  address sc-pool pool

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.100.0 255.255.255.0

  No inside_nat0_outbound access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.1.96 255.255.255.240

  -Jouni

• Help, please! Cannot access the web after connected to the VPN

  Hello

  I'm a newbie on Cisco products.  I configured a Cisco ASA 5505 with VPN firewall.  However, I can't access the web after I connected to the remote IPSec VPN.  I also cannot connect to the bands using the intellectual property.  But I can connect to the internal servers in the office with no problems.

  Here is my setup, can someone help please?  Thank you very much

  ASA Version 8.2 (5)

  !

  host name asa

  xxxxxxxxx.com domain name

  enable the encrypted password xxxxxxxxxxx

  xxxxxxxxxxx encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  passive FTP mode

  area of zone clock - 8 schedule

  clock summer-time recurring PDT 1 Sun Apr 02:00 last Sun Oct 02:00

  DNS lookup field inside

  DNS server-group DefaultDNS

  Server name 107.204.233.222

  name-server 192.168.1.3

  xxxxxxxxx.com domain name

  inside_nat0_outbound list of allowed ip extended access all 192.168.1.96 255.255.255.240

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool sc-192.168.1.100 - 192.168.1.110 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 192.168.1.0 255.255.255.0

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint _SmartCallHome_ServerCA

  Configure CRL

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 192.168.1.0 255.255.255.0 inside

  SSH timeout 5

  Console timeout 0

  interface ID client DHCP-client to the outside

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.5 - 192.168.1.36 inside

  dhcpd dns 107.204.233.222 inside the 192.168.1.3 interface

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal strategy group xxxxxxxx-sc

  attributes of xxxxxxxx-sc group policy

  value of 107.204.233.222 DNS server 192.168.1.3

  Protocol-tunnel-VPN IPSec

  XXXXXXXXXX.com value by default-field

  xxxxx xxxxxxxxxxx encrypted password username

  Strategy Group-VPN-xxxxxxxx-sc

  remote access to tunnel-group xxxxxxxx-sc type

  attributes global-tunnel-group xxxxxxxx-sc

  address sc-pool pool

  Group Policy - by default-xxxxxxxx-sc

  tunnel-group xxxxxxxx-sc ipsec-attributes

  pre-shared key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  call-home service

  anonymous reporting remote call

  call-home

  contact-email-addr [email protected] / * /

  Profile of CiscoTAC-1

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:5c1c99b09fb26fcc36a8bf7206af8e02

  : end

  Hello

  Try adding the following commands

  permit same-security-traffic intra-interface

  NAT (outside) 1 192.168.1.96 255.255.255.240

  Is there are always problems with VPN then I would maybe change VPN pool to anything other than something that comes into conflict with the LAN.

  In this case, these configurations should do the trick

  In order from top to bottom, they would do the following things

  • First remove the pool VPN and VPN configurations
  • Then remove the VPN pool
  • Remake of the VPN Pool with different network
  • Reattach the VPN pool for VPN configurations
  • Configure NAT0 to the new cluster of VPN
  • Remove the old line of the ACL of the configuration of NAT0

  attributes global-tunnel-group xxxxxxxx-sc

  no address-sc-swimming pool

  no ip local pool sc 192.168.1.100 - 192.168.1.110 mask 255.255.255.0

  IP local pool sc-192.168.2.10 - 192.168.2.254 mask 255.255.255.0

  attributes global-tunnel-group xxxxxxxx-sc

  address sc-pool pool

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0

  no access list inside_nat0_outbound extended permits all ip 192.168.1.96 255.255.255.240

  Of course you also have the NAT configuration for VPN pools new Internet traffic

  NAT (outside) 1 192.168.2.0 255.255.255.0

  Please rate if the information has been useful if this resolved the issue as mark responded.

  -Jouni

• Cisco ASA 5510, ipsec vpn. What address to connect the client to

  Hello

  It's maybe a stupid question, but I can't find the answer anywhere.

  I used the ipsec vpn configuration wizard, I activated the external interface to access ipsec and went through SCW pools of addresses etc. When I try to connect with the cisco vpn client to my address of the external interface (of a remote host) I'm unable to connect. I scanned the interface for open ports, but there is not, I have to allow traffic to ipsec at this interface?

  Best regards

  Andreas

  No, once you have configured the access remote vpn ipsec, it will be automatically activated, and you should be able to connect to the ASA outside the ip address of the interface.

  Can you please share the configuration? and also which group name you are trying to access the vpn client?

• Cisco ASA Site to Site VPN IPSEC and NAT question

  Hi people,

  I have a question about the two Site to Site VPN IPSEC and NAT. basically what I want to achieve is to do the following:

  ASA2 is at HQ and ASA1 is a remote site. I have no problem setting a static static is a Site to IPSEC VPN between sites. Guests residing in 10.1.0.0/16 are able to communicate with hosts in 192.168.1.0/24, but what I want is to configure the NAT with IPSEC VPN for this host to 10.1.0.0/16 will communicate with hosts in 192.168.1.0/24 with translated addresses

  Just an example:

  N2 host (10.1.0.1/16) contacted N1 192.168.1.5 with destination host say 10.23.1.5 No 192.168.1.5 (notice the last byte is the same in the present case,.5)

  The translation still for the rest of the communication (host pings ip destination host 10.23.1.6 N3 N2 not 192.168.1.6 new last byte is the same)

  It sounds a bit confusing to me, but I've seen this type of configuration before when I worked for the supplier of managed services where we have given our customers (Ipsec Site to Site VPN with NAT, don't know how it was setup)

  Basically we contact the customer via site-to-site VPN hosts but their real address were hidden and we used as translated address more high 10.23.1.0/24 instead of (real) 192.168.1.0/24, last byte must be the same.

  Grateful if someone can shed some light on this subject.

  Hello

  OK so went with the old format of NAT configuration

  It seems to me that you could do the following:

  • Configure the ASA1 with static NAT strategy
    • access-list L2LVPN-POLICYNAT allowed ip 192.168.1.0 255.255.255.0 10.1.0.0 255.255.0.0
    • public static 10.23.1.0 (inside, outside) access-list L2LVPN-POLICYNAT
  • Because the above is a static NAT of the policy, this means that the translation will be made only when the destination network is 10.1.0.0/16
  • If you have for example a PAT basic configuration to inside-> external traffic, the above NAT configuration and the custom of the actual configuration of PAT interfere with eachother
  • ASA2 side, you can normally configure NAT0 / NAT Exemption for the 10.1.0.0/16 network
    • Note of the INTERIOR-SHEEP access-list SHEEP L2LVPN
    • the permitted INSIDE SHEEP 10.1.0.0 ip access list 255.255.0.0 10.23.1.0 255.255.255.0
    • NAT (inside) 0-list of access to the INTERIOR-SHEEP
  • You will need to consider that your access-list defining the VPN encrypted L2L traffic must reflect the new NAT network
    • ASA1: allowed to access-list L2LVPN-ENCRYPTIONDOMAIN ip 10.23.1.0 255.255.255.0 10.1.0.0 255.255.0.0
    • ASA2: list L2LVPN-ENCRYPTIONDOMAIN allowed ip 10.1.0.0 access 255.255.0.0 10.23.1.0 255.255.255.0

  I could test this configuration to work tomorrow but I would like to know if it works.

  Please rate if this was helpful

  -Jouni

• Unable to connect to the Internet, the error message "Cisco AnyConnect VPN agent service is not responding. Please restart this application after a minute"

  Original title: unable to connect to the internet

  Whenever I connect to my computer and get it on my desk, it goes on to say that Cisco AnyConnect VPN Service not available. How can I fix? I am not connected to the internet and I can't connect to the internet as well. He said also Cisco AnyConnect VPN service agent is not an answer. Please restart this application after a minute. Also, I can't use my firewall for some reason, if I try to allow its loading and the greenbar's going that far - then stops and says that there is an error. I forgot where I tried to activate.

  Oh thanks for the help but I fix it myself. I just did a system restore to a month before

• VPN ipsec Cisco 877 <>- iphone

  Hi, I'm trying implement the vpn ipsec between my cisco 877 and his iphone/cisco vpn client. First of all, what is the difference between remote access vpn and vpn installation easy? The phase 1 and the phase2 are completed but I don't have much traffic between peers.

  Maybe I missed something conf? Should I add the roadmap with acl 101?

  Here is the configuration of isakmp/ipsec.

  ISAKMP crypto enable
  session of crypto consignment

  crypto ISAKMP policy 10
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  life 3600
  ISAKMP crypto keepalive 10
  ISAKMP crypto nat keepalive 20
  ISAKMP xauth timeout 90 crypto

  ISAKMP crypto client configuration group to distance-vpn
  key to past
  DNS 212.216.112.112
  cisco877.local field
  10 Max-users
  Max-connections 10
  pool remotely
  ACL 150
  Save-password

  Crypto ipsec transform-set VPN-CLI-SET esp-3des esp-md5-hmac
  Crypto ipsec security association idle time 3600

  distance from dyn-crypto-dynamic-map 10
  transformation-VPN-CLI-SET game

  card crypto remotemap local-address dialer0
  card crypto client remotemap of authentication list userauthen
  card crypto isakmp authorization list groupauthor remotemap
  client configuration address card crypto remotemap answer
  remotemap 65535 ipsec-isakmp crypto map distance Dynamics-dyn

  interface dialer0
  remotemap card crypto

  IP local pool remote control-pool 192.168.69.0 192.168.69.20

  IP route 192.168.69.0 255.255.255.0 dialer0

  no access list 150
  REM list 150 * ACL split tunnel access *.
  access-list 150 permit ip 10.0.77.0 0.0.0.255 192.168.69.0 0.0.0.255

  no access list 101
  Note access-list 101 * ACL sheep *.
  access-list 101 deny ip 10.0.77.0 0.0.0.255 192.168.69.0 0.0.0.255
  access-list 101 permit ip 10.0.77.0 0.0.0.255 any

  Should I apply this acl 101 loopback?  Ex:

  overload of IP nat inside source list 101 interface Loopback0

  Should I apply an acl to permit as access-list 169 allow ip 192.168.69.0 0.0.0.255 any in my Dialer interface 0?

  Other tips? Best regards.

  Hi Alessandro,.

  The access tunnel split list is great!

  If you are NAT on public and private interface that is ip nat inside and ip nat outside etc.

  You must add the command ip nat inside source list 101 interface Dialer0 overload

  +++++++++++++++++++++++++++++++++++++++

  Or you can create a new roadmap

  new route map permit 10

  ACL #match 101

  command: ip nat inside the interface Dialer0 overload route map

  Thank you

  Adama

• Cisco Anyconnect VPN and IPSEC coexist on ASA 5520?

  Can a Cisco ASA 5520 which has been configured as IPSEC VPN gateway and also be configured as a gateway ANYCONNECT VPN and vpn IPSEC service anyconnect vpn clients clients maintenance at the same time? Any negative impact on the performance or any other problem that everyone knows?

  I guess that by 2 connection limit, you are referring to the 2 licenses for anyconnect?  You should consider using the anyconnect essentials license, which is relatively cheap (100-200 dollars I think) and will take you to the edge of the platform with anyocnnect.

  You shouldn't have any problem using IPSEC with LDAP client.  It is quite common - my company is IPSEC as Anyconnect off the coast of the same interface using authentication ldap (even same-group policy) for the two.

  -Jason