Cisco's VPN IPSec client for LAN connectivity

Similar Questions

• double authentication with Cisco's VPN IPSEC client

  Cisco VPN client (the legacy IPSEC client) does support dual authentication with RSA token AND ActiveDirectory credentials?

  I know that AnyConnect supports it and the commandsecondary- authentication -Server- group' is only for ssl connections, but must be confirmed.

  Kind regards

  Mohammad

  Hi Mohammad,.

  What is double authentication support for Cisco VPN Client?

  A. No. Double authentication only is not supported on the Cisco VPN Client.

  You can find more information on the customer Cisco VPN here.

  As you said the only client that supports dual authentication is the Cisco AnyConnect secure mobility Client.

  Please note and mark it as correct this Post!

  Let me know if there are still questions about it!

  David Castro,

• Setup for use with Cisco Anyconnect VPN IPsec

  So, I had trouble setting up VPN on our ASA 5510. I would use IPsec VPN so that we don't have to worry about licensing issues, but what I have read you can do with and always use Cisco Anyconnect. My knowledge on how to set up VPN especially in iOS version 8.4 is limited, so I've been using a combination of command line and ASDM.

  I am finally able to connect from a remote location, but once I log in, nothing else works. What I've read, you can use IPsec for client-to-lan connections. I use a pre-shared for this. Documentation is limited on what should happen after have connected you? Shouldn't be able to local access on the vpn connection computers? I'm trying to implement work. If I have VPN from home, should not be able to access all of the resources at work? According to me, because I used the command-line as ASDM I confused some of the configuration. In addition, I think that some of the default policies are confused me too. So I probably need a lot of help. Here is my current setup with the changed IP address and other things that are not related to deleted VPN.

  NOTE: We are still testing this ASA and is not in production.

  Any help you can give me is greatly appreciated.

  ASA Version 8.4 (2)

  !

  ASA host name

  domain.com domain name

  !

  interface Ethernet0/0

  nameif inside

  security-level 100

  the IP 192.168.0.1 255.255.255.0

  !

  interface Ethernet0/1

  nameif outside

  security-level 0

  IP 50.1.1.225 255.255.255.0

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  No nameif

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  boot system Disk0: / asa842 - k8.bin

  passive FTP mode

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  !

  permit same-security-traffic intra-interface

  !

  network of the NETWORK_OBJ_192.168.0.224_27 object

  subnet 192.168.0.224 255.255.255.224

  !

  object-group service VPN

  ESP service object

  the purpose of the tcp destination eq ssh service

  the purpose of the tcp destination eq https service

  the purpose of the service udp destination eq 443

  the destination eq isakmp udp service object

  !

  allowed IP extended ip access list a whole

  !

  mask 192.168.0.225 - 192.168.0.250 255.255.255.0 IP local pool VPNPool

  no failover

  failover time-out period - 1

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 645.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.0.224_27 NETWORK_OBJ_192.168.0.224_27 non-proxy-arp-search to itinerary

  !

  the object of the LAN network

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_in in external interface

  Route outside 0.0.0.0 0.0.0.0 50.1.1.250 1

  Sysopt noproxyarp inside

  Sysopt noproxyarp outdoors

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec ikev2 ipsec-proposal OF

  encryption protocol esp

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 proposal ipsec 3DES

  Esp 3des encryption protocol

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal AES

  Esp aes encryption protocol

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal AES192

  Protocol esp encryption aes-192

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 AES256 ipsec-proposal

  Protocol esp encryption aes-256

  Esp integrity sha - 1, md5 Protocol

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  registration auto

  name of the object CN = ASA

  Configure CRL

  crypto ca server

  Shutdown

  string encryption ca ASDM_TrustPoint0 certificates

  certificate d2c18c4e

  864886f7 0d06092a c18c4e30 308201f3 3082015c a0030201 d 020204 2 0d 010105

  0500303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609

  02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109

  3131 31303036 31393133 31365a 17 323131 30303331 39313331 0d 170d 6f6d301e

  365a303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609

  02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109

  6f6d3081 9f300d06 092 has 8648 86f70d01 01010500 03818d b 30818902-00-818100-2

  8acbe1f4 5aa19dc5 d3379bf0 f0e1177d 79b2b7cf cc6b4623 d1d97d4c 53c9643b

  37f32caf b13b5205 d24457f2 b5d674cb 399f86d0 e6c3335f 031d54f4 d6ca246c

  234b32b2 b3ad2bf6 e3f824c0 95bada06 f5173ad2 329c28f8 20daaccf 04c 51782

  3ca319d0 d5d415ca 36a9eaff f9a7cf9c f7d5e6cc 5f7a3412 98e71de8 37150f02

  03010001 300 d 0609 2a 864886 f70d0101 05050003 8181009d d2d4228d 381112a 1

  cfd05ec1 0f51a828 0748172e 3ff7b480 26c197f5 fd07dd49 01cd9db6 9152c4dc

  18d0f452 50f5d0f5 4a8279c4 4c1505f9 f5e691cc 59173dd1 7b86de4f 4e804ac6

  beb342d1 f2db1d1f 878bb086 981536cf f4094dbf 36c5371f e1a0db0a 75685bef

  af72e31f a1c4a892 d0acc618 888b53d1 9b 888669 70e398

  quit smoking

  IKEv2 crypto policy 1

  aes-256 encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 10

  aes-192 encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 20

  aes encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 30

  3des encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 40

  the Encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  Crypto ikev2 activate out of service the customer port 443

  Crypto ikev2 access remote trustpoint ASDM_TrustPoint0

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 10

  Console timeout 0

  management-access inside

  SSL-trust outside ASDM_TrustPoint0 point

  WebVPN

  allow outside

  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

  AnyConnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 2

  AnyConnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 3

  profiles of AnyConnect VPN disk0: / devpn.xml

  AnyConnect enable

  tunnel-group-list activate

  internal VPN group policy

  attributes of VPN group policy

  value of server WINS 50.1.1.17 50.1.1.18

  value of 50.1.1.17 DNS server 50.1.1.18

  Ikev1 VPN-tunnel-Protocol, l2tp ipsec ikev2 ssl-client

  digitalextremes.com value by default-field

  WebVPN

  value of AnyConnect VPN type user profiles

  always-on-vpn-profile setting

  privilege of xxxxxxxxx encrypted password username administrator 15

  VPN1 xxxxxxxxx encrypted password username

  VPN Tunnel-group type remote access

  General-attributes of VPN Tunnel-group

  address (inside) VPNPool pool

  address pool VPNPool

  LOCAL authority-server-group

  Group Policy - by default-VPN

  VPN Tunnel-group webvpn-attributes

  enable VPN group-alias

  Group-tunnel VPN ipsec-attributes

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  class-map ips

  corresponds to the IP access list

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  inspect the http

  class ips

  IPS inline help

  class class by default

  Statistical accounting of user

  I would recommend buy AnyConnect Essentials. The cost of the license is nominal - list of US $150 for the 5510. (piece number L-ASA-AC-E-5510 =)

  Meawwhile you can use the Cisco VPN client inherited with IKEv1 IPSec remote access VPN using profiles *.pcf.

  I believe you can also use the client Anyconnect client SSL or DTLS transport access remotely (non-IPsec) without having to buy the license Anyconnect Essentials for your ASA focus.

  As an aside, note that if you want to use AnyConnect Mobile (e.g. for iPhone, iPad, Android, Blackberry etc.clients) you will also get the additional license for it (L-ASA-AC-M-5510 =, also price US $150)

• IPsec client for s2s NAT problem

  Hello

  We have a remote site (Paris) with a 5512 with some s2s and RA light customer vpn (anyconnect IPsec) tunnels.  AnyConnect has no problem, but the ipsec client can not pass traffic on the LAN.  The subnet behind the fw is 10.176.0.0/16 and the RA 10.172.28.0/24 customer pool.  However, we have a s2s than nat 10.0.0.0/8 tunnel and it appears that customers vpn IPSEC RA being bound traffic matches this rule and prevents connectivity to local resources via vpn ipsec client.

  ......

  hits = 485017, user_data = 0x7fffa5d1aa10, cs_id = 0 x 0, use_real_addr, flags = 0 x 0 = 0 protocol

  IP/ID=10.176.0.0 SRC, mask is 255.255.0.0, port = 0

  IP/ID=10.0.0.0 DST, mask is 255.0.0.0, port = 0, dscp = 0 x 0

  input_ifc = inside, outside = output_ifc

  ...

  Manual NAT policies (Section 1)

  1 (outdoor) static source Paris_Network Paris_Network static destination Remote2_LAN_Networks Remote2_LAN_Networks non-proxy-arp-search to itinerary (inside)

  translate_hits = 58987, untranslate_hits = 807600

  2 (inside) (outside) static source Paris_Network Paris_Network static destination DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2-route search

  translate_hits = 465384, untranslate_hits = 405850

  3 (inside) (outside) static source Paris_Network Paris_Network static destination Remote1_Networks Remote1_Networks-route search

  translate_hits = 3102307, untranslate_hits = 3380754

  4 (outside) (inside) static source Paris_RA_VPN Paris_RA_VPN static destination Paris_Network Paris_Network-route search

  translate_hits = 0, untranslate_hits = 3

  This method works on other sites with almost identical configuration, but for some reason, it doesn't work here.  I can't specify different subnets for the s2s tunnel because there is too much of.  Can someone help me and tell me why I can't get this to work?

  Hello

  So you're saying that the AnyConnect is working but not IPsec? What is the the AnyConnect VPN? It is outside the 10.0.0.0/8 network?

  You should be able to substitute the NAT VPN L2L configuration by simply configuring a separate NAT for the local network for VPN pool traffic at the top of your NAT configurations

  For example

  being PARIS-LAN network

  10.176.0.0 subnet 255.255.0.0

  object netwok PARIS-VPN-POOL

  10.172.28.0 subnet 255.255.255.0

  NAT (inside, outside) 1 static source PARIS PARIS - LAN LAN destination PARIS-VPN-POOL PARIS-VPN-POOL static

  This should ensure that the first rule on the SAA is the NAT rule that matches the VPN Client for LAN traffic. Other aircraft in the L2L VPN should still hit the original NAT rule to the VPN L2L

  If this does not work then we must look closer, the configuration.

  Hope this helps

  Remember to mark a reply as the answer if it answered your question.

  Feel free to ask more if necessary

  -Jouni

• Press L2L VPN, IPSEC, and L2TP PIX connections

  Hi all

  I'm trying to implement a solution on my FW PIX (pix804 - 24.bin) to be able to support a VPN L2L session with VPN dynamic user sessions where clients will use a mix of IPSEC(Nat detection) and L2TP. We have always supported things IPSEC and that worked great for many years. I'm now trying to Add L2TP support, so that I can support Android phones/ipads, etc. as well as Windows with built in VPN l2tp clients clients. Everything works well except for the new features of L2TP. Allows you to complete one phase but then tries to use the card encryption that is used for the VPN L2L. It seems to fail because IP addresses are not in the configured ACL to the crypto-map L2L. Does anyone know if there are any questions all these configurations support both. And if not can you see what I have wrong here, which would make it not work. Here are the relevant training:

  C515 - A # sh run crypto
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set of society-ras-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set esp-3des esp-sha-hmac company-l2tp
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Dynamic crypto map company-ras 1 correspondence address company-dynamic
  company Dynamics-card crypto-ras 1 set pfs
  Dynamic crypto map company-ras 1 transform-set ESP-SHA-3DES ESP-3DES-MD5 company-ras
  Dynamic crypto map company-ras 1 lifetime of security association set seconds 28800
  company Dynamics-card crypto-ras 1 kilobytes of life together - the association of safety 4608000
  crypto dynamic-map-ras company 2 address company-dynamic game
  crypto dynamic-map company-ras 2 transform-set of society-l2tp
  crypto dynamic-map company-ras 2 set security association lifetime seconds 28800
  company Dynamics-card crypto-ras 2 kilobytes of life together - the association of safety 4608000
  card crypto company-map 1 correspondence address company-colo
  card crypto company-card 1 set pfs
  card crypto company-card 1 set counterpart colo-pix-ext
  card crypto card company 1 value transform-set ESP-3DES-MD5 SHA-ESP-3DES
  company-map 1 lifetime of security association set seconds 28800 crypto
  card company-card 1 set security-association life crypto kilobytes 4608000
  company-card 1 set nat-t-disable crypto card
  company-card 2 card crypto ipsec-isakmp dynamic company-ras
  business-card interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside

  Crypto isakmp nat-traversal 3600

  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 2
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400
  C515 - A # sh run tunnel-group
  attributes global-tunnel-group DefaultRAGroup
  company-ras address pool
  Group-LOCAL radius authentication server
  Group Policy - by default-l2tp
  IPSec-attributes tunnel-group DefaultRAGroup
  pre-shared-key *.
  tunnel-group DefaultRAGroup ppp-attributes
  PAP Authentication
  No chap authentication
  ms-chap-v2 authentication
  eap-proxy authentication
  type tunnel-group company-ras remote access
  tunnel-group global company-ras-attributes
  company-ras address pool
  Group-LOCAL radius authentication server
  tunnel-group company-ras ipsec-attributes
  pre-shared-key *.
  type tunnel-group company-admin remote access
  attributes global-tunnel-group company-admin
  company-admin address pool
  Group-LOCAL radius authentication server
  company strategy-group-by default-admin
  IPSec-attributes of tunnel-group company-admin
  pre-shared-key *.
  PPP-attributes of tunnel-group company-admin
  No chap authentication
  ms-chap-v2 authentication
  tunnel-group x.x.x.x type ipsec-l2l
  tunnel-group ipsec-attributes x.x.x.x
  pre-shared-key *.
  ISAKMP keepalive retry threshold 15 10
  C515 - A # sh run Group Policy
  attributes of Group Policy DfltGrpPolicy
  Server DNS 10.10.10.20 value 10.10.10.21
  Protocol-tunnel-VPN IPSec
  enable PFS
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value company-SPLIT-TUNNEL-ACL
  company.int value by default-field
  NAC-parameters DfltGrpPolicy-NAC-framework-create value
  internal strategy of company-admin group
  attributes of the strategy of company-admin group
  WINS server no
  DHCP-network-scope no
  VPN-access-hour no
  VPN - 20 simultaneous connections
  VPN-idle-timeout 30
  VPN-session-timeout no
  Protocol-tunnel-VPN IPSec l2tp ipsec
  disable the IP-comp
  Re-xauth disable
  Group-lock no
  enable PFS
  Split-tunnel-network-list value company-ADMIN-SPLIT-TUNNEL-ACL
  L2TP strategy of Group internal
  Group l2tp policy attributes
  Server DNS 10.10.10.20 value 10.10.10.21
  Protocol-tunnel-VPN l2tp ipsec
  disable the PFS
  Split-tunnel-policy tunnelall
  company.int value by default-field
  NAC-parameters DfltGrpPolicy-NAC-framework-create value

  Relevant debug output

  C515 - Has # Sep 03 02:09:33 [IKEv1 DEBUG]: IP = 66.25.14.195, Oakley proposal is acceptable
  Sep 03 02:09:33 [IKEv1 DEBUG]: IP = 66.25.14.195, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
  Sep 03 02:09:33 [IKEv1 DEBUG]: IP = 66.25.14.195, IKE SA proposal # 1, turn # 1 entry IKE acceptable Matches # 3 overall
  Sep 03 02:09:33 [IKEv1]: IP = 66.25.14.195, connection landed on tunnel_group DefaultRAGroup
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, status of automatic NAT detection: remote endpoint IS behind a NAT device this end is NOT behind a NAT device
  Sep 03 02:09:33 [IKEv1]: IP = 66.25.14.195, connection landed on tunnel_group DefaultRAGroup
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, previously allocated memory of liberation for permission-dn-attributes
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, PHASE 1 COMPLETED
  Sep 03 02:09:33 [IKEv1]: IP = 66.25.14.195, for this connection Keep-alive type: None
  Sep 03 02:09:33 [IKEv1]: IP = 66.25.14.195, Keep-alives configured on, but the peer does not support persistent (type = None)
  Sep 03 02:09:33 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 66.25.14.195, timer to generate a new key to start P1: 21600 seconds.
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID remote Proxy Host: address 172.16.0.104 17 of the Protocol, Port 0
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID local Proxy Host: address x.x.x.x, 17 of the Protocol, Port 1701
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, detected L2TP/IPSec session.
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, QM IsRekeyed its not found old addr
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto, check card company card, seq = 1 =...
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto card = company-map, seq = 1, ACL does not proxy IDs src:66.25.14.195 dst: x.x.x.x
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, tunnel IPSec rejecting: no entry for crypto for proxy card proxy remote 66.25.14.195/255.255.255.255/17/0 local x.x.x.x/255.255.255.255/17/1701 on the outside interface
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, error QM WSF (P2 struct & 0x501c1f0, mess id 0xa181b866).
  Sep 03 02:09:33 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 66.25.14.195, case of mistaken IKE responder QM WSF (struct & 0x501c1f0) , : QM_DONE EV_ERROR--> QM_BLD_MSG2 EV_NEGO_SA--> QM_BLD_MSG2, EV_IS_REKEY--> QM_BLD_MSG2, EV_CONFIRM_SA--> QM_BLD_MSG2, EV_PROC_MSG--> QM_BLD_MSG2, EV_HASH_OK--> QM_BLD_MSG2, NullEvent--> QM_BLD_MSG2, EV_COMP_HASH
  Sep 03 02:09:33 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, peer table correlator Removing failed, no match!
  Sep 03 02:09:33 [IKEv1]: ignoring msg SA brand with Iddm 204910592 dead because ITS removal
  Sep 03 02:10:05 [IKEv1 DEBUG]: IP = 66.25.14.195, Oakley proposal is acceptable
  Sep 03 02:10:05 [IKEv1 DEBUG]: IP = 66.25.14.195, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
  Sep 03 02:10:05 [IKEv1 DEBUG]: IP = 66.25.14.195, IKE SA proposal # 1, turn # 1 entry IKE acceptable Matches # 3 overall
  Sep 03 02:10:05 [IKEv1]: IP = 66.25.14.195, connection landed on tunnel_group DefaultRAGroup
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, status of automatic NAT detection: remote endpoint IS behind a NAT device this end is NOT behind a NAT device
  Sep 03 02:10:05 [IKEv1]: IP = 66.25.14.195, connection landed on tunnel_group DefaultRAGroup
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, previously allocated memory of liberation for permission-dn-attributes
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, PHASE 1 COMPLETED
  Sep 03 02:10:05 [IKEv1]: IP = 66.25.14.195, for this connection Keep-alive type: None
  Sep 03 02:10:05 [IKEv1]: IP = 66.25.14.195, Keep-alives configured on, but the peer does not support persistent (type = None)
  Sep 03 02:10:05 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 66.25.14.195, timer to generate a new key to start P1: 21600 seconds.
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID remote Proxy Host: address 172.16.0.104 17 of the Protocol, Port 0
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID local Proxy Host: address x.x.x.x, 17 of the Protocol, Port 1701
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, detected L2TP/IPSec session.
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, QM IsRekeyed its not found old addr
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto, check card company card, seq = 1 =...
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto card = company-map, seq = 1, ACL does not proxy IDs src:66.25.14.195 dst: x.x.x.x
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, tunnel IPSec rejecting: no entry for crypto for proxy card proxy remote 66.25.14.195/255.255.255.255/17/0 local x.x.x.x/255.255.255.255/17/1701 on the outside interface
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, error QM WSF (P2 struct & 0x501c1f0, mess id 0xa5db9562).
  Sep 03 02:10:05 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 66.25.14.195, case of mistaken IKE responder QM WSF (struct & 0x501c1f0) , : QM_DONE EV_ERROR--> QM_BLD_MSG2 EV_NEGO_SA--> QM_BLD_MSG2, EV_IS_REKEY--> QM_BLD_MSG2, EV_CONFIRM_SA--> QM_BLD_MSG2, EV_PROC_MSG--> QM_BLD_MSG2, EV_HASH_OK--> QM_BLD_MSG2, NullEvent--> QM_BLD_MSG2, EV_COMP_HASH
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, peer table correlator Removing failed, no match!
  Sep 03 02:10:05 [IKEv1]: ignoring msg SA brand with Iddm 204914688 dead because ITS removal

  The outputs of two debugging who worry are the following:

  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID remote Proxy Host: address 172.16.0.104 17 of the Protocol, Port 0
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, data received in payload ID local Proxy Host: address x.x.x.x, 17 of the Protocol, Port 1701

  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto, check card company card, seq = 1 =...
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, static check card Crypto card = company-map, seq = 1, ACL does not proxy IDs src:66.25.14.195 dst: x.x.x.x
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, tunnel IPSec rejecting: no entry for crypto for proxy card proxy remote 66.25.14.195/255.255.255.255/17/0 local x.x.x.x/255.255.255.255/17/1701 on the outside interface
  Sep 03 02:10:05 [IKEv1]: Group = DefaultRAGroup, IP = 66.25.14.195, error QM WSF (P2 struct & 0x501c1f0, mess id 0xa5db9562).

  This seems to indicate that his NAT detection but then do not assign to the entry card cryptography because networks are encrypted are not in the configured ACL that is true. He needs to use dynamic input and it doesn't seem to be.

  I need to create another dynamic map entry to make it work instead of add lines to the same dynamic with a lower (higher) priority map entry?

  Thanks in advance for any help here.

  Hello

  That won't do the trick, l2tp clients are picky kindda, so you know if they do not hit the correct strategy first they just stop trying. Follow these steps:

  correspondence from the company of dynamic-map crypto-ras 1 address company-dynamic

  No crypto-card set pfs dynamic company-ras 1

  No crypto dynamic-map company-ras-1 transform-set ESP-SHA-3DES ESP-3DES-MD5 company-ras

  Dynamic crypto map company-ras 1 transform-set company-l2tp SHA-ESP-3DES ESP-3DES-MD5 company-ras

  The foregoing will not affect existing customers of IPsec at all, these clients will not use the statement of pfs and will link even if the correspondence address is not configured (it is optional), besides Cisco IPsec clients will be affected first the mode of transport policy and fail however they will continue to try and hit another police PH2.

  Regarding your last question, I was referring specifically to the support of l2tp for android, and Yes, you will need to run one of these versions.

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/release/notes/asarn82.html#wp431562

  Tavo-

• Cisco's VPN IPSec help please

  Hi all

  I have 3 sites, the main site has a cisco firewall mikrotik router.

  There is a vpn ipsec existing between the cisco router and another router cisco on the site of the 2nd and it works well.

  Now, I've added an another vpn between a 3rd site and main site. The router on the 3rd site is a mikrotik firewall.

  I had the vpn on the main site and the 3rd site where the mikrotik firewall is and it worked well.

  then for some reason, the vpn with the 3rd site has failed and I could not get it working again.

  When looking for answers, I see that the vpn for the 3rd site States the following:

  #pkts program: 46, #pkts encrypt: 46, #pkts digest: 46
  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0

  It seems that no traffic is coming back to the cisco

  I also found the following output below to diagnose the problem.

  It seems that there is communication, but if I read this right, it looks like the cisco established a new number but the other end is not the new number

  new node-1868419487

  node-1868419487 error suppression FALSE "Information (in) condition 1" pattern

  Any help would be appreciated.

  * 02:49:51.911 Jul 22: ISAKMP: (2060): purge the node-1140469772

  * 02:49:59.723 Jul 22: ISAKMP: DPD received message KMI.

  * 02:49:59.723 Jul 22: ISAKMP: node set 1053074288 to QM_IDLE

  * 02:49:59.723 Jul 22: ISAKMP: (2060): Protocol for sending INFORMER DPD/R_U_THERE 1

  SPI 2273844328, message ID = 1053074288

  * 02:49:59.723 Jul 22: ISAKMP: (2060): seq. no 0x645EC368

  * 02:49:59.723 Jul 22: ISAKMP: (2060): my_port of x.x.x.127 package sending 5

  peer_port 00 500 (R) QM_IDLE

  * 02:49:59.723 Jul 22: ISAKMP: (2060): sending a packet IPv4 IKE.

  * 02:49:59.723 Jul 22: ISAKMP: (2060): purge the node 1053074288

  * 02:49:59.767 Jul 22: ISAKMP (2060): packet received dport x.x.x.127

  500 sport Global 500 (R) QM_IDLE

  * 02:49:59.767 Jul 22: ISAKMP: node set-1868419487 to QM_IDLE

  * 02:49:59.771 Jul 22: ISAKMP: (2060): HASH payload processing. Message ID = 24265

  47809

  * 02:49:59.771 Jul 22: ISAKMP: (2060): treatment of the NOTIFY DPD/R_U_THERE_ACK protoco

  l 1

  0, message ID SPI = 2426547809, a = 0x8705F854

  * 02:49:59.771 Jul 22: ISAKMP: (2060): DPO/R_U_THERE_ACK received from the peer 125,23

  6.211.127, sequence 0x645EC368

  * 02:49:59.771 Jul 22: ISAKMP: (2060): node-1868419487 FALSE reason for deletion error

  "Information (in) condition 1"

  * 02:49:59.771 Jul 22: ISAKMP: (2060): entry = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY

  * 02:49:59.771 Jul 22: ISAKMP: (2060): former State = new State IKE_P1_COMPLETE = IKE

  _P1_COMPLETE

  * 02:50:01.111 Jul 22: ISAKMP: (2060): purge the node-1201068805

  Comparing encrypt of 46 to 47436 counters, it seems that router is ecncrypting the traffic, but we do not get any interesting traffic on the remote side.

  Most likely, you might want to check on the remote site, if you see counters increment in parallel decryption and encryption of the counters are incrementing or not.

  On the router IOS, if are incrementing counters encrypt, and confirm that you have not any tunnel existing before the router can be seen same proxy IDs, which is already negotiated with other peer.

  Finally, please make sure that the ESP, 50 protocol traffic is not blocked in transit.
  I hope this helps.

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• Connectivity VPN IPSec Client to ASA5510

  I have an ASA5510 at a remote site. I used the IPSec VPN Wizard to configure remote access for developers in the portion of the DMZ network 192.168.100.0/24.

  I can connect using two the last customer Cisco Windows and using VPNC on my Linux machine. A tunnel is created, I get a valid IP within the 192.168.100.0 subnet and everything is great.

  But when I try to ssh to one of the servers, the SYN package times out. I can see the connection tries to establish by looking at the logs on the firewall.

  There is no problem with Linux servers themselves to who I am trying to connect. I've ridden iptables and even tried to connect without any firewall rule. Still no dice.

  I can post my running-config here if necessary.

  Thank you.

  Well just ensure that ISAKMP desired on your firewall policy is at the top. This will reduce the time for negotiation for Phase 1. Also, make sure that there is no fragmentation (MTU issues).

  Concerning

  Farrukh

• License of Cisco 2821 VPN IpSEC

  Hello

  I have a small problem, a do give me a Cisco 2821 for installing a VPN client to a small local network.

  I don't have problem to the router connection, but when I try to set up an ipsec i cant.

  We have need of a license or a module installation IpSe VPN?

  When I run this command, the router does not include:

  vpnbog1 (config) #crypto isakmp policy 1

  ^

  Invalid entry % detected at ' ^' marker.

  vpnbog1 (config) #.

  the show version is:

  January 3, 21:12:49.219: % SYS-5-CONFIG_I: configured from console by admin on consoleversion

  Software (fc2) SOFTWARE VERSION, Cisco IOS, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4 (3i)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 1986-2007 by Cisco Systems, Inc.

  Updated Thursday 28 November 07 21:09 by stshen

  ROM: System Bootstrap, Version 12.4 (13r) T, RELEASE SOFTWARE (fc1)

  vpnbog1 uptime is 1 hour, 32 minutes

  System to regain the power ROM

  System restarted at 14:40:43 PCTime Friday January 3, 2014

  System image file is "flash: c2800nm-spservicesk9 - mz.124 - 3i.bin".

  This product contains cryptographic features and is under the United States

  States and local laws governing the import, export, transfer and

  use. Delivery of Cisco cryptographic products does not imply

  third party approval to import, export, distribute or use encryption.

  Importers, exporters, distributors and users are responsible for

  compliance with U.S. laws and local countries. By using this product you

  agree to comply with the regulations and laws in force. If you are unable

  to satisfy the United States and local laws, return the product.

  A summary of U.S. laws governing Cisco cryptographic products to:

  http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html

  If you need assistance please contact us by mail at

  [email protected] / * /.

  Cisco 2821 (revision 53.51) with 251904 K/K 10240 bytes of memory.

  Card processor ID FTX1213A06Y

  2 gigabit Ethernet interfaces

  2 FXS voice interfaces

  Configuration of DRAM is wide with parity 64-bit capable.

  239K bytes of non-volatile configuration memory.

  62720K bytes of ATA CompactFlash (read/write)

  You are tuning a "spservices" image that has no crypto code compiled (AFAIR, feel free to doublecheck).

  You would need advanced security or advanced IP services have together.

  http://www.Cisco.com/en/us/prod/collateral/routers/ps5853/images/0900aecd80524a07_null_null_null_07_19_05-1.jpg

  M.

• Cisco AnyConnect Secure mobility Client cannot initialize connection subsystem after updates Windows (Feb 10, 2015)

  Hello

  The customer Cisco Anyconnect Secure mobility gives me an error when I try to use it. It started after the latest updates for Windows (10 Feb. 2015).

  The error it causes is "could not initialize the subsystem of connection".

  I looked at another machine with the updates installed with same issue.

  On my machine - I back before restore point windows updates be done, and the Cisco Anyconnect Client's worked well.

  After you install the updates, it stopped working again.

  Help, please

  Michael

  I assume you are using Windows 8.1. The workaround is to set the AnyConnect Client to use Windows 8 Compatibility Mode. He has worked on several machines. After the change, you will need to log off the coast and turn it on for Windows.

  Cumulative update 11 IE KB3021952 includes KB3023607.  Apparently, it's the latest patch that causes the problem, according to what I said. (I do not even 3023607 in the history of WU, but if I type "wmic qfe" is here). However, I suggest updating leaving in place and using workaround.

• You still need to download the SQL client for ODBC connection?

  I plan to install vCenter on windows 2008 R2 and the connection to a SQL 2008 database.   I remember having to download SQL client, to establish the ODBC connection, is this always the case?

  Yes, you need SQL Native Client.  You can download below

  http://www.Microsoft.com/download/en/details.aspx?ID=16978

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• 506th PIX IPSEC VPN allow authentication for local users?

  We have a 6.3 (5) running PIX 506th, configured for Cisco's VPN IPSEC clients. Cisco VPN clients authenticate with the credentials of group fine, but is it possible to use local users to authenicate plu? We use local users to our existing PPTP VPN clients, but we want to migrate these users to IPSEC. Any info would be greatly appreicated.

  Of course, you can... you need to include the command on your card crypto below

  map LOCAL crypto client authentication

  I hope this helps... Please, write it down if she does!

• Routing VPN Ipsec

  Morning,

  I have an ASA 5520 of Cisco running 8.4 (5). When to use a VPN ipsec client and it connects to the local network, how the connection interprets her return flights. Currently, I have all my servers pointing to the front door on our old firewall. I have a different gateway on the new Cisco firewall. It is a transitional phase we are permanently than one Cisco ASA 5520 firewall. For testing purposes, we want to test the configuration of the VPN client with our front Radius Server cut us above. Test users must connect to resources on the corporate network. Should I put a route on the old firewall so when packets hit VPN servers they will know how to return to the VPN tunnel or the source and destination address will already be taken into account when the tunnel VPN hits the server, packages will return to the tunnel. The Cisco VPN client does not NAT configuration. Once we feel that the test is passed, we will change the gateway from the Cisco ASA 5520 to match the existing bridge for all resources on the network.

  Information or advice would be greatly appreciated?

  Thank you

  Carlos

  On the SAA, you set up a pool of IP addresses for the client. This pool should be aligned on the subnet boundaries. On your infrastructure (L3 switch or your old firewall), you tricky staric asa for this pool-network. Thereby the packages of answer-VPN-will flow to the ASA.

  Sent by Cisco Support technique iPad App

• Misconfigured remote VPN server by using IPSEC client

  I'm trying to figure out what I did wrong in my setup.  The environment is:

  ASA 5505 running 8.2 with 6.2 ASDM.

  Version of the VPN Client 5.0.05.0290

  I installed VPN ipsec clients both anyconnect and connected successfully to the remote access VPN server. However, the client doesn't show any returned package.  Thinking that I have badly configured, I have reset to the default value of the factory and began again.  Now I only have the configured ipsec vpn and I have exactly the same symptoms.  I followed the instructions to configure the ipsec vpn in Document 68795 and double-checked my setup and I don't know what I did wrong.  Because I can connect to the internet from inside network and I can connect to the VPN from outside of the network (and the ASDM Watch monitor an active connection with nothing sent to the client) I believe this is a road or an access rule preventing communication but I can't quite figure out where (and I tried the static routes to the ISP and a wide variety of access rules before rinsing to start) above).

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  internal group vogon strategy
  attributes of vogon group policy
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list vogon_splitTunnelAcl
  username password privilege encrypted 0987654321 zaphod 15
  username password encrypted AaBbCcDdEeFf privilege 0 arthur
  username arthur attributes
  VPN-group-policy vogon
  tunnel-group vogon type remote access
  tunnel-group vogon General attributes
  address pool VPN_Pool
  strategy-group-by default vogon
  tunnel-group vogon ipsec-attributes
  pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:xxxxxxxxxxxxxxxxxxxxxx
  

  Looks like a typo for the Pool of IP subnet mask.

  You currently have:

  mask 10.92.66.10 - 10.92.66.24 255.255.0.0 IP local pool VPN_Pool

  It should be:

  mask 10.92.66.10 - 10.92.66.24 255.255.255.0 IP local pool VPN_Pool

  Please kindly change the foregoing and test, if it still does not work, please please add the following:

  management-access inside

  Policy-map global_policy
  class inspection_default

  inspect the icmp

  Then try to VPN in and see if you can ping 10.92.65.1 and let us know if this ping works.

  Please also share the output of: "cry ipsec to show his" after the trial, if it does not work.

• Delete the profile of AnyConnect secure mobility Client for Windows

  Hello

  My Cisco AnyConnect Secure Mobility Client for Windows (Version 3.1.04063 in fact) has stored some Clientprofiles. How can I remove one of these profiles if I do not need more?

  I already searched the registry and the file system but without success. I don't know where this information is stored.

  Any suggestions?

  Thank you

  They are individual xml files in a hidden directory. The location on Windows 7 is:

  C:\ProgramData\Cisco\Cisco AnyConnect secure mobility Client\Profile

  The complete inventory of their storage location for various operating systems can be found in the Guide of Administration AnyConnect.