Cisco SR520 - no outgoing access

Similar Questions

• CISCO RV180 - limited VPN access

  Hello!

  I use CISCO router RV180 to incoming VPN connections. I'm just learning how to do, I did all the settings and it works now. However, I have noticed that users who connect through their VPN Clients can see the entire internal network. Those who may be limited to only certain local IPs?

  For example, my local network is 10.x.x.x. I have CISCO Router Web Interface available to connect to 10.x.x.1 and the Web server I want users to access is on 10.x.x.2. Can I forbid access for VPN users that connect through the IP CISCO address so this 10.x.x.1 address is available for local users only?

  Slava,

  What I meant by my intervention is PPTP give you users access to the entire network. With Port Forwarding, users have access to the server that listens on port 443. Because port 443 using the https protocol, it is a secure connection.

  If your users have Windows 7 or below, you can try QuickVPN. Simply activate the remote port 443 or 60443 management and add users. (No IKE Policy is necessary because the router must listen QuickVPN connections automatically) With QuickVPN end users will have access to everything on the VLAN 1, so you can create another VIRTUAL local network for devices that do not have access to.

  If you use a third-party VPN client as Shrewsoft (Windows) or IPSecuritas (Mac), you should be able to restrict access only to the server. (You will need to create an IKE and VPN policy)

  -Marty

• authentication 802. 1 x on cisco VPN for remote access

  I'm on dial-up VPN (mobile VPN) on cisco ASA5510, now, I want to authenticate remote users via Microsoft IAS (Radius Standard) service. However, I couldn't get through the via protocol PEAP authentication process, and it seems that it only supports PAP that isn't safe.

  Any suggestion on how to implement PEAP over VPN remote access?

  Thank you

  Hello

  Glance atv http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00806de37e.shtml

  It may be useful.

  Best regards.

  Massimiliano.

• Cisco ISE and WLC Access-List Design/scalability

  Hello

  I have a scenario that wireless clients are authenticated by the ISE and different ACL is applied depending on the rules in the ISE. The problem I have seen is due to the limitation on the Cisco WLC that limit only 64 input access list. As the installer has only a few IVR/interfaces and several different access lists are applied to the same base on user groups interface; I was wondering if there may be an evolutionary design / approach according to which the access list entries can evolve next to create a vlan for each group of users and apply the access list on the interface of layer 3 instead? I illustrated the configuration below for reference:

  Group of users 1 - apply ACL 1 - on Vlan 1

  User 2 group - apply ACL 2 - on the Vlan 1

  3 user group - apply ACL 3 - on the Vlan 1

  The problem appears only for wireless users, he does not see on wired users as the ACLs can be applied successfully without restriction as to the switches.

  Any suggestion is appreciated.

  Thank you.

  In fact, you have limitations on the side of the switch as well. Long ACL can deplete resources AAGR of the switch. Take a look at this link:

  http://www.Cisco.com/c/en/us/support/docs/switches/Catalyst-3750-series-switches/68461-high-CPU-utilization-cat3750.html

  The new WLCs based on IOS XE and not the old OS Wireless/Aironet will provide the best experience in these matters.

  Overall, I see three ways to overcome your current number:

  1. reduce the ACL by making them less specific

  2 use L3 interfaces on a switch L3 or FW and the ACL is applied to them

  3. use the SGT/SGA

  I hope this helps!

  Thank you for evaluating useful messages!

• Cisco 1532E standalone (bypass + Access Client)

  Hi all.

  I need to connect two places separated from 300 meters and I also need access to the wireless client.

  My idea is to use two Cisco 1532 (in stand-alone mode) with antennas directional 5 GHz to fill and Omni 2, 4 GHz antennas for wireless in both clients.

  My problem is that the deployment guide does not refer to this implementation (standalone + bridge + wireless clients); the deployment guide is located in the following link http://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/7-6/b_1532_dg/b_1532_dg_chapter_01.html#topic_5C2E00D8A63A462AAC6F0A0DC629FBDF

  Can anyone confirm if this is a supported scenario?

  Thank you

  João Carvalho.

  Each radio is configured separately one from the other, so you re the 5 GHz as bridge and the 2.4 ghz as the root of station, the client access role.  You can refer to any stand-alone for bridge (root and non-root) configuration and client access guide.

  Here's an older doc, you can refer:

  https://supportforums.Cisco.com/document/61936/autonomous-AP-and-bridge-...

  Scott

• How to assign a vlan per port cisco all point of access by wlc 702w 5508

  My environment have WLC 5508 and ap 702w 250 units in my site. I need on port port config example all the ap 702w 2 > Vlan 20 port 3 > vlan 30

  Now I canfig one by one.

  Please everyone tell me best way to config a time 250 units.

  Thank you very much...

  Here is the config CLI involved. If you have a list of your AP names you can config CLI of training for all your AP on Notepad & then configure this CLI

  config ap lan port-id  enable config ap lan enable access vlan   

  See this post for more details https://mrncciew.com/2014/09/26/702w-with-wlc-8-0/ HTH Rasika * Pls note all useful responses *.

• Cisco SGE2010P LAG in access or trunk mode?

  Hello.

  I have a client who has two SGE2010P connected by four LAG ports.

  Switch has all the users, and B a whole server. All used on the vlan 1.

  Now I had to add the point with multiple SSID access.

  Here the port I created trunk port since the AP had to pass several tag/no identified images.

  So now the two trunk vlan is spent. One is the vlan 1 and other native vlan 2 for the wireless of comments.

  If I were to set up access to this port, the AP Gets the ip address of the DHCP server on the other switch.

  When I set up the trunk, the gi0.1, which is part of the vlan native Gets the ip address.

  However, the Gi0.2 interface, which is part of the vlan 2 does not get an ip address.

  When I put the port vlan 2 access mode and got the AP to be in this vlan.

  I was able to get the ip address on the scope of vlan2. It's only when I set up the trunk port.

  the vlan 2 (not native vlan) does not get an ip address.

  So I think it is, maybe the LAG port is in access mode in the vlan 1 and not in trunk mode.

  Is it possible to change the port of OFFSET to be in trunk mode?

  Thank you in advance.

  Hi Thomas, that there should be "M1" in the list of the interface down. Or some channel port that you assigned. As an OFFSET, these ports are more specific. It works exactly the same in a catalyst environment, difference is, it's on a GUI config vs a CLI config.

  -Tom
  Please mark replied messages useful

• Updated standalone Cisco Aironet lightweight mode Access Points

  I'm trying to convert a stand-alone Aironet 1200 in light Mode. I use the tool to upgrade v1.0 proposed by Cisco. But when I put the name of the recovery LWAPP Image (c1200-k9w7 - tar.123 - 7.JA2) in the tool window to update it doesn't work. It is said: c1200-k9w7 - tar.123 - 7.JA2 - LWAPP recovery Image file size is zero. But its size is 4.6 MB!

  Can someone help me?

  Convert the Aironet 1200 of autonomous light mode follow the procedure set out in document http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp23144.

• Cisco ASA Anyconnect LAN access problem

  I have very simple network at home with the WAN IP address, ASA uses DHCP and gateway. plain of network of all no complications.

  X.X.X.X like a WAN

  192.168.1.0/24 as a LAN

  IP Pool 192.168.6.0/24 (VPN Pool)

  I am trying to configure AnyConnect (AC) so that I can connect remotely and get my resources on the LAN while out. I am to connect with AC and when you use split tunnel I'm browsing the web very well, but I have no access to the local network (without ICMP or TCP/UDP)

  Route looks good in customer AC

  unsecured network 0.0.0.0/0
  secure network 192.168.1.0/24

  What I'm missing for LAN access?, nat statement, list of access...?

  _____________________________

  Output of the command: "show run".

  : Saved
  :
  ASA Version 9.1 (5)
  !
  hostname asa01
  domain name asa

  names of
  192.168.6.2 mask - 192.168.6.100 local pool Pool VPN IP 255.255.255.0
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  switchport access vlan 5
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  interface Vlan2
  Outside description
  nameif outside
  security-level 0
  IP address XXXX
  !
  interface Vlan5
  nameif dmz
  security-level 50
  IP 192.168.100.1 address 255.255.255.0
  !
  boot system Disk0: / asa915 - k8.bin
  passive FTP mode
  clock timezone PST - 8
  clock summer-time recurring PDT
  DNS lookup field inside
  DNS domain-lookup outside
  DNS domain-lookup dmz
  DNS server-group DefaultDNS
  domain naisus.local
  permit same-security-traffic intra-interface
  network of the NETWORK_OBJ_192.168.1.0_24 object
  subnet 192.168.1.0 255.255.255.0
  network of the NETWORK_OBJ_192.168.6.0_25 object
  subnet 192.168.6.0 255.255.255.128
  object-group Protocol DM_INLINE_PROTOCOL_1
  icmp protocol object
  icmp6 protocol-object
  outside_access_in list extended access permit icmp any any idle state
  outside_access_in extended access list allow icmp6 all all idle state
  outside_access_in_1 list extended access allow DM_INLINE_PROTOCOL_1 of object-group a
  list of access allowed standard LAN 192.168.1.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  host of logging inside 192.168.1.99
  forest-hostdown operating permits
  Within 1500 MTU
  Outside 1500 MTU
  MTU 1500 dmz
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 741.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) static source NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.6.0_25 NETWORK_OBJ_192.168.6.0_25 non-proxy-arp-search of route static destination
  !
  NAT source auto after (indoor, outdoor) dynamic one interface
  Access-group outside_access_in_1 in interface outside
  Route outside 0.0.0.0 0.0.0.0 X > X > X >
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Crypto ipsec ikev2 ipsec-proposal OF
  encryption protocol esp
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 proposal ipsec 3DES
  Esp 3des encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES
  Esp aes encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES192
  Protocol esp encryption aes-192
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 AES256 ipsec-proposal
  Protocol esp encryption aes-256
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec pmtu aging infinite - the security association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  Crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
  registration auto
  full domain name no
  name of the object CN = asa01, CN = 192.168.1.1
  ASDM_LAUNCHER key pair
  Configure CRL
  trustpool crypto ca policy
  string encryption ca ASDM_Launcher_Access_TrustPoint_0 certificates
  certificate 8b541b55
  308201c 3 c 3082012 a0030201 0202048b 0d06092a 864886f7 0d 010105 541b 5530
  XXXX
  quit smoking
  IKEv2 crypto policy 1
  aes-256 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 10
  aes-192 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 20
  aes encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 30
  3des encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 40
  the Encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  Crypto ikev2 access remote trustpoint ASDM_Launcher_Access_TrustPoint_0
  Telnet 192.168.1.0 255.255.255.0 inside
  Telnet timeout 5
  SSH stricthostkeycheck
  SSH 192.168.1.0 255.255.255.0 inside
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0

  dhcpd outside auto_config
  !
  dhcpd address 192.168.1.100 - 192.168.1.199 inside
  dhcpd dns 8.8.8.8 75.75.75.75 interface inside
  dhcpd naisus.home area inside interface
  dhcpd allow inside
  !
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  NTP server 50.116.56.17 source outdoors
  NTP server 108.61.73.243 source outdoors
  NTP server 208.75.89.4 prefer external source
  SSL-trust outside ASDM_Launcher_Access_TrustPoint_0 point
  Trust ASDM_Launcher_Access_TrustPoint_0 inside the vpnlb-ip SSL-point
  SSL-trust ASDM_Launcher_Access_TrustPoint_0 inside point
  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-win-3.1.07021-k9.pkg 1 regex 'Windows NT'
  AnyConnect image disk0:/anyconnect-macosx-i386-3.1.07021-k9.pkg 2 regex "Intel Mac OS X.
  AnyConnect image disk0:/anyconnect-linux-64-3.1.07021-k9.pkg 3 regex "Linux".
  AnyConnect enable
  tunnel-group-list activate
  attributes of Group Policy DfltGrpPolicy
  VPN - connections 30
  VPN-idle-timeout 5
  internal GroupPolicy_AC_Profile group strategy
  attributes of Group Policy GroupPolicy_AC_Profile
  WINS server no
  4.2.2.2 DNS server value
  client ssl-VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value LAN
  naisus.local value by default-field
  XX XX encrypted privilege 15 password username
  name of user XX attributes
  WebVPN
  chip-tunnel tunnel-policy tunnelall
  type tunnel-group AC_Profile remote access
  attributes global-tunnel-group AC_Profile
  address pool VPN-pool
  Group Policy - by default-GroupPolicy_AC_Profile
  tunnel-group AC_Profile webvpn-attributes
  enable AC_Profile group-alias
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:xxx
  : end

  I'm not positive that's causing the problem, but I noticed that you have defined incoherent poolside VPN as a 24 (in the command name and that name is associated with the tunnel group) and 25 (in the command object on the network that is also referenced in the statement of NAT exempting NAT to that object). True your pool assigns addresses from the lower half of the 24, but still...

  I try to simplify things by using a single object for something like that, which is used in several places. With the help of objects the way they are intended, and which allows to avoid any discrepancies.

• How to configure a Cisco No. 2851 to access customer VPN Cisco router?

  It is my current configuration below, can someone help me see problems with it:

  AAA new-model
  !
  !
  AAA authentication local connection user
  AAA authorization network group local
  AAA accounting update newinfo

  crypto ISAKMP policy 10
  BA 3des
  preshared authentication
  !
  crypto ISAKMP policy 11
  BA 3des
  preshared authentication
  Group 2
  !
  12 crypto isakmp policy
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 15
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 20
  md5 hash
  preshared authentication

  !
  ISAKMP crypto client configuration group vpngroup
  key cisco123
  pool VPN_POOL

  Crypto ipsec transform-set esp-3des esp-sha-hmac vpnc1
  !
  Crypto-map dynamic dynmap 15
  Set transform-set vpnc1
  !
  !

  local IP 10.1.1.1 VPN_POOL pool 10.1.1.20

  list user card crypto Test client authentication
  card crypto isakmp authorization list Group Test
  Crypto map Test address client configuration address
  Discover 15 Test card crypto ipsec-isakmp dynamic dynmap
  !
  !
  !
  !
  interface GigabitEthernet0/0
  Description *.
  IP address
  NAT outside IP
  IP virtual-reassembly
  automatic duplex
  automatic speed
  No cdp enable
  card crypto Test

  Hi Ralema,

  Please see this link:

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00800949ba.shtml

  It will be useful.

  Federico.

• PIX behind Cisco 1841 - need SSH access

  Hello, trying to enable SSH access to PIX for some external host clinets.

  What are the correct Acl I need?

  Exactly correct...

  1 - on the router, you must allow incoming TCP 22 (ssh) to your PIX on the external interface of the router and also allow the flow back of the PIX inside interface of the router.

  2. - to the PIX you must generate rsa keys and save them.

  CA generates the key rsa 1024

  CA save all

  3 - on the pix you will need to allow ssh acccess to you outside of the interface

  SSH outdoors

  Write it down if you find it useful

• Cannot access network resources - Cisco VPN client

  Please see attached the network topology.

  I can connect using the Cisco VPN client and access to all resources of the 192.168.3.0 network

  I can't ping / access to all hosts on the network 192.168.5.0.

  Any ideas?

  Thanks for the help in advance

  AD

  Quite correct.

  Please add has the access list:

  CPA list standard access allowed 192.168.5.0 255.255.255.0

• Remote access VPN Cisco ASA

  Hello!

  I have 9.1 (3) version of Cisco ASA with remote access VPN set UP on the outside interface. When the user connects to the Internet on the outside interface, it works well. My goal is to allow the connection of all other interfaces (inside the dmz and etc.) to the outside interface. Cisco ASA allows to do? Order to packet - trace output is less to:

  MSK-hq-fw1 # packet - trace entry inside tcp 10.10.10.1 14214 1.1.1.2 443

  Phase: 1

  Type:-ROUTE SEARCH

  Subtype: entry

  Result: ALLOW

  Config:

  Additional information:

  developed 1.1.1.2 255.255.255.255 identity

  Phase: 2

  Type:-ROUTE SEARCH

  Subtype: entry

  Result: ALLOW

  Config:

  Additional information:

  developed 1.1.1.2 255.255.255.255 identity

  Result:

  input interface: inside

  entry status: to the top

  entry-line-status: to the top

  the output interface: NP identity Ifc

  the status of the output: to the top

  output-line-status: to the top

  Action: drop

  Drop-reason: (headwall) No. road to host

  Hello

  Well, you can of course turn VPN on other interfaces, but to be honest, I never even tried to set up the VPN it otherwise than of multiple multiple external interfaces in the case of the ISP and in this case only for testing purposes.

  Some things related to the ASA are well known but not well documented.

  The official document that I can remember: this is the following (which only refers to this limitation regarding the ICMP)

  Note 
  For  security purposes the security appliance does not support far-end  interface ping, that is pinging the IP address of the outside interface  from the inside network.
  

  Source (old configuration guide):

  http://www.Cisco.com/c/en/us/TD/docs/security/ASA/asa71/configuration/guide/conf_gd/trouble.html#wp1059645

  -Jouni

• Question of access list for Cisco 1710 performing the 3DES VPN tunnel

  I have a question about the use of access lists in the configuration of a router Cisco 1710 that uses access lists to control traffic through the VPN tunnel.

  For example the following lines in a configuration on the remote router. My question is whether or not the traffic that matches the definition of list access-130 (something other than 192.168.100.0/24), cross the VPN tunnel or go directly to the Ethernet0 interface.

  My understanding is that traffic that matches the access list 120 would be encrypted and sent through the IPSec tunnel. If there was "ban" set out in the statements of 120 access-list, the traffic for those would be sent through the IPSec tunnel but not encrypted (if possible). And finally, given that the definition of crypto card reference only "adapt to 120", any traffic that matches 130 access list would be sent Ethernet0 but not associated with the card encryption and thus not sent through the IPSec tunnel. "

  Any input or assistance would be greatly appreciated.

  Map Test 11 ipsec-isakmp crypto

  ..

  match address 120

  Interface Ethernet0

  ..

  card crypto Test

  IP nat inside source overload map route sheep interface Ethernet0

  access-list 120 allow ip 192.168.100.0 0.0.0.255 10.10.0.0 0.0.255.255

  access-list 130 refuse ip 192.168.100.0 0.0.0.255 10.10.0.0 0.0.255.255

  access-list 130 allow ip 192.168.100.0 0.0.0.255 any

  sheep allowed 10 route map

  corresponds to the IP 130

  He would go through the interface e0 to the Internet in clear text without going above the tunnel

  Jean Marc

• Issue of Cisco AnyConnect VPN access

  We have configured a Cisco ASA 5505 with access AnyConnect.  It works very well.  However, these users can't ping on the private network devices.  We have configured all devices on the network with an address 10.10.10.0/24 space.  The inside interface of the ASA I 10.10.10.1/24 and the VPN return addresses are 10.10.10.50 - 10.10.10.65/24.

  They users can use SSH and Oracle or MySQL calls but can't ping.   Obviously, I'm looking for something.

  Thank you.

  Dwane

  Hi Sylvie,.

  Most likely, your ASA missing no. - nat between inside the interface and remote vpn-pool address range.

  Quick Trobule shooting, thanks for posting your config and do not forget to remove the config security information.

  What version of your ASA?

  Thank you

  Rizwan James