Cisco vpn Mac

Similar Questions

• Comments Win XP cannot connect to the network when Cisco VPN works on Mac

  Guest OS (Win XP) on the merger connects to the network, no problem. However, when I start a Cisco VPN on my Mac (not in the guest operating system) and then start Fusion/guest OS, the guest cannot connect to the network.

  I was able to use this configuration for a year on an old MacBook Pro (unibody). Last month, I got a new MacBook Pro and flying over my virtual machine image. I don't check for a few weeks. I'm sure I fly over the image correctly because everything else seems OK or if the IT guys doing something to block my traffic over the VPN.

  Config

  -Fusion - Version 3.1.0 (261 058)

  -Mac - 10.6.4

  So far, I have tried the following

  -started to merge and XP without VPN on Mac - OK (bridge autodetect)

  -launched VPN to work, and then launched Fusion - no network

  -tried ipconfig/release, ipconfig / renew - not always no network

  -tried NAT - do always no network

  Thanks in advance. For any help or suggestion will be greatly appreciated.

  Bernie

  The NAT value and then restart the virtual machine.  Works for me with the VPN client built into a cisco router.

  Do not work the real on 10.6.4 cisco software unless you really need to.

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• Cisco VPN

  User using laptop with + 10.4 of Mac OS X (intel) is unable to connect to the Cisco VPN.

  Well, then there is probably something wrong. But with this little information, it is impossible to help.

• Cisco VPN client put in place

  Hi guru of cisco

  Help me please to configure VPN access on ASA 5505 for Cisco VPN Client. I want to let the customers gateway, but access remote 192.168.17.0/24 and 192.168.10.0/24 (connected through site-to-site) networks.

  Will be much appreciated for your help.

  My config:

  Output from the command: 'display conf '.

  !
  ASA Version 8.2 (2)
  !
  name of host host1
  domain domain name
  activate the encrypted password password
  encrypted passwd password
  names of
  !
  interface Vlan1
  Description INTERNET
  0000.0000.0001 Mac address
  nameif WAN
  security-level 0
  IP address a.a.a.a 255.255.255.248 watch a1.a1.a1.a1
  OSPF cost 10
  !
  interface Vlan2
  OLD-PRIVATE description
  0000.0000.0102 Mac address
  nameif OLD-private
  security-level 100
  IP 192.168.17.2 255.255.255.0 watch 192.168.17.3
  OSPF cost 10
  !
  interface Vlan6
  Description MANAGEMENT
  0000.0000.0106 Mac address
  nameif management
  security-level 100
  IP 192.168.1.2 255.255.255.0 ensures 192.168.1.3
  OSPF cost 10
  !
  interface Vlan100
  Failover LAN Interface Description
  !
  interface Ethernet0/0
  !
  interface Ethernet0/1
  Shutdown
  !
  interface Ethernet0/2
  Shutdown
  !
  interface Ethernet0/3
  Shutdown
  !
  interface Ethernet0/4
  Shutdown
  !
  interface Ethernet0/5
  switchport access vlan 100
  !
  interface Ethernet0/6
  switchport trunk allowed vlan 2.6
  switchport mode trunk
  !
  interface Ethernet0/7
  Shutdown
  !
  boot system Disk0: / asa822 - k8.bin
  passive FTP mode
  DNS domain-lookup WAN
  DNS server-group DefaultDNS
  Server name dns.dns.dns.dns
  domain domain name
  permit same-security-traffic intra-interface
  object-group Protocol TCPUDP
  object-protocol udp
  object-tcp protocol
  object-group service RDP - tcp
  RDP description
  EQ port 3389 object
  object-group Protocol DM_INLINE_PROTOCOL_1
  ip protocol object
  icmp protocol object
  object-protocol udp
  object-tcp protocol
  Access extensive list ip 192.168.17.0 LAN_nat0_outbound allow 255.255.255.0 192.168.10.0 255.255.255.0
  Standard access list LAN_IP allow 192.168.17.0 255.255.255.0
  WAN_access_in list of allowed ip extended access all any debug log
  WAN_access_in list extended access allowed icmp a.a.a.a 255.255.255.248 192.168.10.0 255.255.255.0 inactive debug log
  WAN_access_in list extended access permit tcp any object-group RDP any RDP log debugging object-group
  WAN_access_in list extended access allowed icmp a.a.a.a 255.255.255.248 a.a.a.a 255.255.255.248 debug log
  MANAGEMENT_access_in list of allowed ip extended access all any debug log
  access-list extended OLD-PRIVATE_access_in any allowed ip no matter what debug log
  access-list OLD-PRIVATE_access_in allowed extended object-group DM_INLINE_PROTOCOL_1 interface OLD-private 192.168.10.0 255.255.255.0 inactive debug log
  access-list OLD-PRIVATE_access_in allowed extended object-group TCPUDP interface OLD-private no matter what inactive debug log
  access-list OLD-PRIVATE_access_in allowed extended icmp host 192.168.10.254 interface private OLD newspaper inactive debugging
  access-list OLD-PRIVATE_access_in allowed extended icmp host 192.168.17.155 interface private OLD newspaper debugging
  access-list 101 extended allow host tcp 192.168.10.7 any eq 3389 debug log
  Access extensive list ip 192.168.17.0 WAN_1_cryptomap allow 255.255.255.0 192.168.10.0 255.255.255.0
  WAN_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0
  WAN_cryptomap_2 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0
  Capin list extended access permit ip host 192.18.17.155 192.168.10.7
  Capin list extended access permit ip host 192.168.10.7 192.168.17.155
  LAN_access_in list of allowed ip extended access all any debug log
  Access extensive list ip 192.168.17.0 WAN_nat0_outbound allow 255.255.255.0 192.168.10.0 255.255.255.0
  WAN_nat0_outbound list of allowed ip extended access all 192.168.17.240 255.255.255.252
  WAN_nat0_outbound to access extended list ip 192.168.2.0 allow 255.255.255.0 192.168.2.0 255.255.255.248
  Access extensive list ip 192.168.17.0 WAN_2_cryptomap allow 255.255.255.0 192.168.10.0 255.255.255.0
  permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.17.0 255.255.255.0
  LAN_IP_inbound list standard access allowed 192.168.10.0 255.255.255.0
  Standard access list IPSec_VPN_splitTunnelAcl allow a
  access extensive list ip 192.168.17.0 vpnusers_splitTunnelAcl allow 255.255.255.0 any
  sheep - in extended Access-list allow IP 192.168.17.0 255.255.255.0 192.168.2.0 255.255.255.0
  vpn_ipsec_splitTunnelAcl list standard access allowed 192.168.2.0 255.255.255.0
  pager lines 24
  Enable logging
  logging trap information
  asdm of logging of information
  Debugging trace record
  MTU 1500 WAN
  MTU 1500 OLD-private
  MTU 1500 management
  mask 192.168.1.150 - 192.168.1.199 255.255.255.0 IP local pool VPN_Admin_IP
  IP local pool vpnclient 192.168.2.1 - 192.168.2.5 mask 255.255.255.0
  failover
  primary failover lan unit
  failover lan interface failover Vlan100
  15 75 holdtime interface failover pollTime
  key changeover *.
  failover interface ip failover 192.168.100.1 255.255.255.0 ensures 192.168.100.2
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP permitted host b.b.b.b WAN
  ICMP allow 192.168.10.0 255.255.255.0 WAN
  ICMP permitted host c.c.c.c WAN
  ICMP allow 192.168.17.0 255.255.255.0 WAN
  ICMP deny any WAN
  ICMP permitted host OLD-private b.b.b.b
  ICMP allow 192.168.10.0 255.255.255.0 OLD-private
  ICMP allow 192.168.17.0 255.255.255.0 OLD-private
  ICMP permitted host c.c.c.c OLD-private
  ICMP permitted host b.b.b.b management
  ICMP permitted host 192.168.10.0 management
  ICMP permitted host 192.168.17.138 management
  ICMP permit 192.168.1.0 255.255.255.0 management
  ICMP permitted host 192.168.1.26 management
  ASDM image disk0: / asdm - 631.bin
  don't allow no asdm history
  ARP timeout 14400
  Global (WAN) 1 interface
  Global (OLD-private) 1 interface
  Global interface (management) 1
  NAT (OLD-private) 0-list of access WAN_nat0_outbound
  NAT (OLD-private) 1 0.0.0.0 0.0.0.0
  WAN_access_in access to the WAN interface group
  Access-group interface private-OLD OLD-PRIVATE_access_in
  Access-group MANAGEMENT_access_in in the management interface
  Route WAN 0.0.0.0 0.0.0.0 a.a.a.185 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  local AAA authentication attempts 10 max in case of failure
  Enable http server
  http 192.168.1.0 255.255.255.0 WAN
  http 0.0.0.0 0.0.0.0 WAN
  http a.a.a.a 255.255.255.255 WAN
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Service resetoutside
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  card crypto WAN_map 1 corresponds to the address WAN_1_cryptomap
  card crypto WAN_map 1 set peer b.b.b.b
  WAN_map 1 transform-set ESP-DES-SHA crypto card game
  card crypto WAN_map WAN interface
  ISAKMP crypto enable WAN
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 30
  preshared authentication
  the Encryption
  sha hash
  Group 1
  life 86400
  Telnet timeout 5
  SSH b.b.b.b 255.255.255.255 WAN
  SSH timeout 30
  SSH version 2
  Console timeout 0
  dhcpd auto_config OLD-private
  !

  a basic threat threat detection
  host of statistical threat detection
  Statistics-list of access threat detection
  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
  NTP server 129.6.15.28 source WAN prefer
  WebVPN
  attributes of Group Policy DfltGrpPolicy
  Protocol-tunnel-VPN IPSec svc webvpn
  internal admin group strategy
  group admin policy attributes
  DNS.DNS.DNS.DNS value of DNS server
  Protocol-tunnel-VPN IPSec
  internal vpn_ipsec group policy
  attributes of the strategy of group vpn_ipsec
  value 192.168.17.80 DNS server dns.dns.dns.dns
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list vpn_ipsec_splitTunnelAcl
  the address value vpnclient pools
  username admin password encrypted password privilege 15
  n1ck encrypted password privilege 15 password username
  type tunnel-group admin remote access
  tunnel-group admin general attributes
  address pool IPSec_VPN_pool
  vpnclient address pool
  LOCAL authority-server-group
  strategy-group-by default admin
  tunnel-group admin ipsec-attributes
  pre-shared-key *.
  tunnel-group b.b.b.b type ipsec-l2l
  tunnel-group b.b.b.b General-attributes
  strategy-group-by default admin
  b.b.b.b tunnel ipsec-attributes group
  pre-shared-key *.
  NOCHECK Peer-id-validate
  type tunnel-group vpn_ipsec remote access
  tunnel-group vpn_ipsec General-attributes
  vpnclient address pool
  Group Policy - by default-vpn_ipsec
  vpn_ipsec group of tunnel ipsec-attributes
  pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp

  Thanks a lot for the confirmation. There is some lack of configurations and also some configuration errors.

  They are here:

  (1) Split tunnel-access list is incorrect:

  vpn_ipsec_splitTunnelAcl list standard access allowed 192.168.2.0 255.255.255.0

  It should be allowed in your internal network. Please, add and remove the following:

  standard access list vpn_ipsec_splitTunnelAcl allow 192.168.17.0 255.255.255.0

  No vpn_ipsec_splitTunnelAcl of the standard access list only allowed 192.168.2.0 255.255.255.0

  (2) NAT 0-list of access should also include the traffic between the local subnet to the Pool of IP VPN:

  Access extensive list ip 192.168.17.0 WAN_nat0_outbound allow 255.255.255.0 192.168.2.0 255.255.255.0

  (3) dynamic-map has not been created and assigned to crypto card:

  Crypto-map dynamic dynmap 10 game of transformation-ESP-3DES-SHA

  card crypto ipsec WAN_map 65000-isakmp dynamic dynmap
  

  (4) Finally, you have not enabled protocol IPSec in your group strategy:

  attributes of the strategy of group vpn_ipsec

  Protocol-tunnel-VPN IPSec

  Hope that helps.

  If it still does not after the changes described above, please kindly share the latest config and also the output of the following debugs when you try to connect:

  debugging cry isa

  debugging ipsec cry

• Kernel panic reproducible when using VMWare Fusion and Cisco VPN

  I can reliable reproduce a kernel panic when I use VMWare Fusion and Cisco VPN set.

  Using either done alone causes no problem.

  I'm on a mac book pro using the latest updates from Apple for Leopard.

  My question is: How can I report this to VMWare without having to pay for support?

  When I go to the VMWare fusion support page he wants me to pay for an incident.

  I really do not want to pay them to help solve a kernel panic.  (They pay me .)

  Announcing the details here (don't forget to join the panic.log as in HOWTO: ask (and answer) Questions) will work.

• Cisco VPN does not work in the Sierra

  I just upgraded to OS Sierra and the Cisco VPN, I had the installer does connect more.  The Setup looks right into network preferences. When I click it looks like it is trying but stops without asking for a password.

  Cisco VPN client may need to update or re-installed. If she uses the PPTP Protocol, it will not work. Support for PPTP was ignored, because it is no longer considered as secure.

• Cisco VPN and TOSHIBA 3G cards

  Hello

  Since the introduction of WIN7 there was a big problem with the Cisco VPN client and 3G cards.
  See the next on the Cisco support forum thread: https://supportforums.cisco.com/thread/2017102

  The interesting part is this post:
  https://supportforums.Cisco.com/message/3166246#3166246
  It seems that Cisco uses what is called Citrix DNE.

  So I Googled it and came up with this link:
  http://www.Citrix.com/lang/English/LP/lp_1680845.asp

  On this page it says:
  DNE now supports the WWAN devices in Win7. Before you download the latest version of DNEUpdate from the links below, make sure you have the latest drivers for your network card by downloading from the websites of sellers.

  It might be a long shot, but someone can it there with a card 3 G TOSHIBA, win7, and cisco VPN access, try this new version of Citrix DNE?

  You have Toshiba laptop with 3G card?
  Can you test for us and post the result?

  I n t have Win7 on my machine.

• Unable to connect to the Cisco VPN you use native client: El Capitan

  I'm unable to connect to the Cisco VPN using native client server Cisco OSX via IPSec. Before the upgrade for connections VPN El Capitan has worked without any problems. VPN uses the shared secret of group. It seems, I get the error "raccoon [2580] ': could not send message vpn_control: Broken pipe ' during the connection."

  When I upgraded to El Capitan, VPN connection has stopped working. I tried to do the following:

  * connect using the old work VPN connection: without success

  Config: Hand [server address, account name],

  AUTH settings [shared secret, the Group name].

  Advanced [mode to use the passive FTP = TRUE]

  errors:

  "authd [124]: copy_rights: _server_authorize failed.

  "raccoon [2580]: could not send message vpn_control: Broken pipe"

  ...

  * Add new VPN connection using L2TP over IPSec: without success

  Config: Hand [server address, account name],

  Authentication settings [user authentication: password, identification of the Machine: Shared Secret].

  Advanced [send all traffic on the VPN = TRUE]

  errsors:

  "pppd [2616]: password not found in the system keychain.

  "authd [124]: copy_rights: _server_authorize failed.

  ...

  
  

  * Add new connection using Cisco via IPSec VPN: without success

  Main config: [server address, account name].

  AUTH settings [shared secret, the Group name].

  Advanced [mode to use the passive FTP = TRUE]

  errors:

  "authd [124]: copy_rights: _server_authorize failed.

  "raccoon [2580]: could not send message vpn_control: Broken pipe"

  VPN server is high and does not work and accepts connections, this problem is entirely on the client side.

  I. Journal of Console app existing/Legacy VPN connection:

  26/03/16 10:24:01, 000 syslogd [40]: sender ASL statistics

  26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: received an order to start SystemUIServer [2346]

  26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: changed to connecting status

  26/03/16 10:24:01, nesessionmanager 313 [2112]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, 316 nesessionmanager [2112]: phase 1 of the IPSec from.

  26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.

  26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.

  26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 339 [2580]: connection.

  26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:24:01, racoon 349 [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

  26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status

  26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status

  26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0

  26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2

  26/03/16 10:24:01, nesessionmanager 404 [2112]: phase 1 of the IPSec from.

  26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 405 [2580]: connection.

  26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:24:01, 407 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

  26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0

  26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0

  26/03/16 10:24:01, 463 raccoon [2580]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).

  26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer

  26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer

  26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).

  26/03/16 10:24:01, 463 raccoon [2580]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).

  26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).

  26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).

  26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).

  26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.

  26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.

  26/03/16 10:24:01, nesessionmanager 485 [2112]: IPSec asking extended authentication.

  [26/03/16 10:24:01, 494 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed by disconnecting

  26/03/16 10:24:01, 495 nesessionmanager [2112]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 495 [2580]: IKE Packet: forward the success. (Information message).

  26/03/16 10:24:01, racoon 495 [2580]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).

  26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe

  26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe

  [26/03/16 10:24:01, 496 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed to offline, last stop reason no

  26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".

  26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".

  26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

  $VPN_SERVER_IP

  II. new VPN connection using L2TP over IPSec Console app log:

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetFillColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetStrokeColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextFillRects: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextClipToRect: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontAntialiasingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveTrackingHandler:-1856

  26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveReceiveHandler:-1856

  26/03/16 10:37:28, com.apple.xpc.launchd [1 393]: (com.apple.SystemUIServer.agent [2346]) Service was released due to the signal: Broken pipe: 13

  26/03/16 10:37:28, Spotlight 461 [459]: spot: logging agent

  26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}

  26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}

  26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: received an order to start com.apple.preference.network.re [2539]

  26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: changed to connecting status

  26/03/16 10:37:28, com.apple.SecurityServer [75 536]: rules of problem opening the file "/ etc/authorization ': no such file or directory

  26/03/16 10:37:28, com.apple.SecurityServer [75 536]: sandbox has denied authorizing the right "system.keychain.modify" customer "/ usr/libexec/nehelper" [184]

  26/03/16 10:37:28, 536 pppd [2616]: NetworkExtension is the controller

  26/03/16 10:37:28, 538 pppd [2616]: NetworkExtension is the controller

  26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: cannot copy content, returned SecKeychainItemCopyContent user interaction is not allowed.

  26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: SecKeychainItemFreeContent returned the user interaction is not allowed.

  26/03/16 10:37:28, 570 pppd [2616]: password not found in the system keychain

  26/03/16 10:37:28, 572 pppd [2616]: publish_entry SCDSet() failed: success!

  26/03/16 10:37:28, 573 pppd [2616]: publish_entry SCDSet() failed: success!

  26/03/16 10:37:28, 573 pppd [2616]: pppd 2.4.2 (Apple version 809.40.5) started by $VPN_SERVER_USER, uid 501

  26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceConnectedCallback

  26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceDisconnectedCallback

  26/03/16 10:37:28, authd 720 [124]: copy_rights: _server_authorize failed

  26/03/16 10:37:28, sandboxd 748 [120]: nehelper (184) ([184]) refuse the authorization-right-get system.keychain.modify

  III. New connection of Cisco VPN through IPSec Console app log:

  26/03/16 10:18:26, 917 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f

  26/03/16 10:19:43, 975 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f

  [26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: received an order to start SystemUIServer [2346]

  [26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: changed to connecting status

  26/03/16 10:19:56, nesessionmanager 267 [2112]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, nesessionmanager 270 [2112]: phase 1 of the IPSec from.

  26/03/16 10:19:56, authd 284 [124]: copy_rights: _server_authorize failed

  26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.

  26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.

  26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, racoon 296 [2576]: connection.

  26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:19:56, racoon 308 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

  26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status

  26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status

  26/03/16 10:19:56, nesessionmanager 352 [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0

  26/03/16 10:19:56, nesessionmanager 353 [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2

  26/03/16 10:19:56, nesessionmanager 373 [2112]: phase 1 of the IPSec from.

  26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, 374 raccoon [2576]: connection.

  26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:19:56, racoon 376 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

  26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0

  26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0

  26/03/16 10:19:56, racoon 432 [2576]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).

  26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer

  26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer

  26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).

  26/03/16 10:19:56, racoon 432 [2576]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).

  26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).

  26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).

  26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).

  26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.

  26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.

  26/03/16 10:19:56, 454 nesessionmanager [2112]: IPSec asking extended authentication.

  [26/03/16 10:19:56, nesessionmanager 464 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed by disconnecting

  26/03/16 10:19:56, nesessionmanager 464 [2112]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:19:56, racoon 465 [2576]: IKE Packet: forward the success. (Information message).

  26/03/16 10:19:56, racoon 465 [2576]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).

  26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe

  26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe

  [26/03/16 10:19:56, nesessionmanager 465 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed to offline, last stop reason no

  26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".

  26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".

  26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP

  It seems that I solved the problem, but I'm not sure it helped.

  After restart of the operating system, the two connections: old and new Cisco via IPSec connection, began to work.

• Cisco VPN Client causes a blue screen crash on Windows XP Pro (Satellite M30)

  Hello

  I have a Satellite Pro M30 running Windows XP Professional.

  After you start a vpn Tunnel via a customer of Cisco VPN (Version 4.6 and 4.7), the system crashes with a blue screen.

  I see that the key exchange is successful, but immediately after the vpn connection is established Windows XP crashes with a blue screen.

  Someone has any idea how to solve this problem?

  Perhaps by the updated device driver? And if so, which driver should be updated?

  Kind regards

  Thorsten

  Hello

  Well, it seems that the Cisco client is a problem.
  I m unaware of this product because it of not designed by Toshiba.
  I think that the drivers are not compatible with the Windows operating system.
  However, I found this site troubleshooting cisco vpn client:
  Please check this:
  http://www.CITES.uiuc.edu/wireless/trouble-index.html

• No Cisco VPN?

  I see no application Cisco VPN, no option under settings VPN Cisco VPN, free VPN Cisco mentioned in the manual, no Cisco VPN ANYWHERE!

  Is anyone else able to find a way to use Cisco VPN? It was an advertised feature which seems to be lacking!

  
  

• Receive message "Validation of C:\WINDOWS\System32\VSINIT.dll failure" error message when trying to run Cisco VPN Client.

  windows\system32\vsinit.dll

  I try to run CISCO "VPN Client" connect from my PC at home for my work PC.

  Then, I get a message:

  Validation failed for C:\WINDOWS\System32\VSINIT.dll

  Any ideas?

  Martin

  Hello

  Run the checker system files on the computer. Link, we can see: Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe): http://support.microsoft.com/kb/310747

  Note that: if he asks you the service pack CD, follow these steps from the link: you are prompted to insert a Windows XP SP2 CD when you try to run the tool on a Windows XP SP2 computer system File Checker: http://support.microsoft.com/kb/900910 (valid for Service pack 3)

  If the steps above is not enough of it please post your request in the TechNet forum for assistance: http://social.technet.microsoft.com/Forums/en/category/windowsxpitpro

• error 28000 removing the cisco vpn

  When I try to remove the software vpn cisco to my windows xp pro, I get error 28000 say failed to install before the removal of the existing version.it is the only vpn on my pc. I tried several times but to no avail.
  I went to the window registry local machine, then soft and deleted the cisco vpn software. but it does not work.
  any help will be grateful?

  Hello alsky95,

  I do not know what records you remove to uninstall the software, I suggest you to follow the article which you will give information on how to uninstall manually below and upgrade the Cisco VPN Client I found on Cisco's Web site:

  http://www.Cisco.com/en/us/products/sw/secursw/ps2308/products_tech_note09186a0080094b7f.shtml

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756 ) how to back up and restore the registry in Windows

  Thank you
  Irfan H, Engineer Support Microsoft Answers

• Cisco VPN problem with security update KB3057839 for Vista

  Someone had problems with any connection Cisco VPN works after the installation of update of security KB3057839 for Vista? When this update is installed, the pop-up to enter the password and user id not come, need to use the Task Manager to close the program. The first time I went back to the restore point to get my VPN to work, this time I tried to reinstall the VPN but that doesn't work anymore. I started to uninstall updates (had 7 of them), when I got to it, KB3057839, the VPN began working again.

  Mike

  See this on the real issue:

  http://www.chiark.greenend.org.uk/~sgtatham/PuTTY/wishlist/Vista-update-breaks-config.html

  It turns out that the logon dialog box is invisible, but still, it agrees to enter you your password and LOG you!

• Professional Windows Vista crashes when you use Cisco VPN Client 5.05.0290

  I have a Dell Latitude E6400 Windows Vista Business (32 bit) operating system. When I go to turn on the VPN client, I get invited to my username / password and once entered, the system just hangs. The only way to answer, it's a re-start. I took action:

  1 disabled UAC in Windows
  2 tried an earlier version of the VPN client
  3. by the representative of Cisco, I put the application runs as an administrator

  If there are any suggestions or similar stories, I would be grateful any offereings.

  It IS the COMODO Firewall with the 5.0.x CISCO VPN client that causes the gel. The last update of COMODO has caused some incompatibility. I tried to install COMODO without the built in Zonealerm, but it is still frozen. The only way to solve it is to uninstall COMODOD. Since then, my CISCO VPN client works again...