Cisco WAPP551 cannot reset and timeout error

Similar Questions

• slow and timeout error

  Hello forum members

  I wrote a program in LV2010 and works very well except for one last question.

  The program works very slowly and sometimes shows error timeout. In the program, I send a voltage to Keithley 2400 and simultaneously measure the current Keithley 2400 and 2000. I sweep the voltage using a while loop. I have not used buffer.

  Your help would be very appreciated.

  Thank you.

  Pradeep

  A few things I noticed:

  1. You should not mix GPIB and VISA to speak to the same instrument.  You should just use the entry VISA to send your order.  But if there is a VI later in driver for the 2400 set the voltage from the source, you should use that.
  2. If you insist on the construction of your own SCPI command to set the voltage of the source, make sure that the command structure is correct.  You may need to add a semicolon or an end of line at the end of the command character.  That's what I suspect causes the header not defined error.
  3. Really, you should add a delay between voltage and then perform readings.
  4. I don't like the idea of allowing the two different screws communicates on the same bus at the same time.  I've seen some strange things with GPIB.  You should sequence a little more so that you adjust the tension, wait 500ms (round number to allow things to sort out and the bus to talk to nice), read the voltage of the 2400, read the current 2000.
  5. Your back measures seem to me.  I usually use the 2400 (source meter) at a voltage of the source and read the current, then read the voltage to the unit under test with the 2000 (DMM).

• r7000 router cannot reset and unable to connect more.

  Hello

  I just bought this router for capacities of bridges in my student apartment.

  I connected by wire and the first disappointment, I discovered that you can not use safety in bridge mode? It seems insane to me because that way no matter who can connect to it or the hack.

  I changed the connectivity in AP mode, after which I lost the connection to the router. I'm trying to reset the router to its factory settings by pressing the reset button. This does not seem to do something good. I can still see the SSID name which I changed and I can't connect to the screen routerlogin. Is this broken thing already? I have a great experience with the netgear switches, but this seems to * beep *. What is going on.

  Determined to RMA it to the store. They played sort of an update of the firmware (no idea how because I couldn't access interface).

  It works perfectly now.

  Pretty weird, but it does not work out of the box.

  Thnx all.

• Equium A100 - 306 PSAABE - cannot start and the error of the BIOS

  I have a Toshiba Equium A100-306, which does not go beyond the BIOS screen. Last thing I did was delete the second partition on the hard drive and the boot configuration Winodws via DVD. Then he stopped display

  If I hit ESC on the post screen, I get a screen that says this: http://i57.photobucket.com/albums/g232/Medabot_Metabee/BIOS_ERR.jpg

  Ive read that theres a method of emergency crisis of flashing, is possible to run it on this laptop?

  Thank you

  Hello

  This looks like a malfunction of the motherboard, you can enter in the setup of the BIOS for example? If Yes, load default settings then save & exit it.

  If you can t get into BIOS try remove the battery and the AC adapter at least an hour. Then connect the two again and try to start your laptop.

  He starts correctly now?

• Cannot reset and be recognized. I m stupid

  I ve just got the chip as a gift and I feel bad and stupid instead of good.

  Try to connect to my galaxy tab 3, android 4.4.2 and bluetooth 4.0, it appears as swr10, in the list displays a mac address and its impossible to connect. I started thinking it was defective

  So I try with my phone of the boss, an xperia, and voila, swr10 appears and connected to the phone, therefore seems not to be defective, and I have it not matched.

  but

  I m desperatrly because I can't get it back, I ve try a million times

  a long heartbeat, lights, a - c then b, same secuence appears twice

  a long pulse once again, light sources on to a, b and c

  a long pulses, light up, a to c, then b secuence, twice

  If I short pulse, on, a to c, then b twice

  If I do an extra long first pulse lights, has to c, then b secuence, twice and then secuence c-b-a.

  and if before this secuence, I press to vibrations, light on secuence a-b-c

  I don't know what I m doing, but I can't put a light flashing to start trying to pair it with my Tablet

  I reed all the information but are not for Dummies, I do not understand when turned on, when turns off, when is day and night

  Please need help

  

  Hello!

  After you install an application on the device, I discovered that same samsung galaxy tab 3 7 "with 4.4.2 and bluetooth 4.0 android is not, that is why smartband is appeas on the list of bluetooth devices.

  On the recovery mode, I try more than 3 hours and he was unable to put the band on this mode. It appears suddenly on the bluetooth list from another phone I tested, but easy to connect not connect to it because it was not in recovery mode.

  A half hour ago, matching and matching smartband and phone but without connection and all doing the same thing to put the group into recovery mode I get there! and 'A' flahsing light crush, I have paired with smart conection, install apps and smartband work

  Thanks for all your help and I hope that happens to me help other people too

• Error of Winsock2? Am online, ping OK, cannot navigate. Winsock Reset and the PC just restarts

  I was unable to sail for some time now.  have reset TCP/IP Stack and when I stay winsock for active administrator CMD prompt - PC comes from the reboot.  problem still exists.

  Checked in MSINFO32 | Components | Network | Protocol - and only listed 7 (not 10)

  have tried several times to reset the WINSOCK2, whenever he freaks out PC and it kicks to a reboot, no resolution.

  Skype, update, etc all work OK - just cannot browse and E-mail

  Any ideas?

  See you soon

  Paul

  Hello

  Make sure that the computer is clean of malware, before we do Winsock TCP/IP update.

  WinSock and TCP/IP update.
  
  Type Cmd in the search text box.

  Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type netsh winsock reset at the command prompt and press the Enter key.

  The same processes to refresh the TCP/IP replaces the command typed with.
  
  netsh int reset press Enter
  
  ipconfig/flushdns press enter

  Restart your computer.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Good method to reset the tcp connection after timeout error

  I have an application that I build that communicates with a Modbus TCP device.  If a communication occurs error I wish I could reset it TCP communication.  What I have is a control that raises an event when pushed.  In this case, I have a sequence that closes first the tcp connection and then opens a new connection.  My application starts and works very well.  To test the reset function, I removed the ethernet cable from the camera and waited until a timeout occurs.  I plugged the cable reset back to and pushed my control. Sometimes the reset will take place, but most of the time I'll get a timeout in the TCP vi open error.  After that, the only way I can establish communications must leave my application, disable and then enable the network device.  Then, when I restart my application I have communication with my camera.

  Any help would be appreciated on how I should be reset my TCP connection.

  Thank you

  Terry

  Terry S of a. in writing:

  I've attached an example vi (LV10) that shows just the connection TCP and Reset.  An error occurs when you try to run the open in the event of reset tcp protocol.

  As writing that your code should be fine. There is nothing inherently wrong with it. However, depending on the device, you communicate with you can try to restore the connection too quickly once you have closed the connection. The device allows multiple connections to it and may require some time to clean up the things on his end after you close a connection. An experimental basis try wait little time between TCP and the TCP Open shut it down. If possible you can try using Wireshark to see what is happening on the network. It may be useful to diagnose what is happening.

• "Cannot install update and the error occurred ' iOS 9.3.2

  Try to upgrade to 9.3.2 but get "cannot install update and the error has occurred" if I am on WIFI or via iTunes. Someone else?

  Go to settings > general > storage & use iCloud > manage storage (the first) > and if there is an update, delete it. Then go to settings > general > Software Update and try again.

• Cannot access Pathname you have the appropriate permissions. Cannot download updates gives error code 643 and error code 5. Always gives access denied.

  Cannot access Pathname you have the appropriate permissions. Cannot download updates gives error code 643 and error code 5. Always gives access denied. You do not have the appropriate permissions. I am the administrator. Change all the complete control. Any other suggestions? Possible virus?

  Hello

  You are unable to download the updates?

  Try the following steps to resolve the problem:

  Method 1: Temporarily disable any security (including firewalls) software and check if the problem persists.

  Check out these links:
  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  If disabling the security software solves the problem, then contact the manufacturer of the specific security software to fix the problem.

  Important: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable
  your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are
  connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2:
  See the article mentioned below and run the Fixit diagnostic tool to fix the error 643.

  You receive error code 80070643 0 x or 0 x 643, code error when you use the Windows Update or Microsoft Update Web sites to install updates:
  http://support.Microsoft.com/kb/958052

  
  Kind regards
  Afzal Taher-Microsoft Support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I forgot the password of hotmail and cannot reset it

  I forgot the password of hotmail and cannot reset the password. What can I do? I made another account on live.com. I want my old account.

  Hello

  Answers is a peer group supported and unfortunately has no real influence on Hotmail.

  HotMail has its own Forums, so you can ask your questions there.

  Windows Live Solution Center - HotMail - HotMail Forums Solutions
  http://windowslivehelp.com/

  Hotmail - Forums
  http://windowslivehelp.com/forums.aspx?ProductID=1

  Hotmail - Solutions
  http://windowslivehelp.com/solutions.aspx?ProductID=1

  How to contact Windows Live Hotmail Support
  http://email.about.com/od/hotmailtips/Qt/et_hotmail_supp.htm

  Windows Live Hotmail Top issues and Support information
  http://support.Microsoft.com/kb/316659/en-us

  Compromised account - access unauthorized account - how to recover your account
  http://windowslivehelp.com/solution.aspx?SolutionID=6ea0c7b3-1473-4176-b03f-145b951dcb41

  Hotmail hacked? Take these steps
  http://blogs.msdn.com/b/securitytipstalk/archive/2010/07/07/Hotmail-hacked-take-these-steps.aspx

  I hope this helps.

• When I import pictures from my iPhone 4s in the Windows Photo Gallery, some come head down and cannot be rotated. Error code 0 x 80070057

  original title: Error Code 0 x 80070057

  When I import pictures from my iPhone 4s in the Windows Photo Gallery, some come head down and cannot be rotated.  Error code 0 x 80070057

  I use Windows Vista.  Help, please.

  Paint has definitely worked for me!  I tried to in WLPG (open with paint) then shot and recorded in the paint.  It is automatically changed in WLPG.  Thanks for the suggestion.

• Cannot access windows 0x800CCC90 and 0x800CCC92 errors messages

  Suddenly, I was unable to access my emails after you have entered the user name and password (normally done automatically) and get error 0x800CCC90 and 0x800CCC92 codes.  My ISP (TalkTalk) do not offer support on Windows Mail.    If I confused with my password can I reset it... or can I rload Windows Mail without losing my data?

  Completely remove the account. Compact and repair the database, and then restart. Add the account back.
   
  WMUtil
  http://www.oehelp.com/WMUtil/default.aspx
   
   

• Cannot send and received the error windows live mail 3219

  Cannot send and received the message of error windows live mail 3219 how remedy

  You use a hosted Microsoft e-mail address.

  Microsoft doesn't want you using a program like WLM.  I know, they created it, but they changed their minds.  They want to be able to use their webmail system so that they can put ads in your face and you profile by reading your emails.  They try to get you migrated to Windows 10 and the e-mail program integrated here.

  Most of my clients with addresses hosted Microsoft migrated far by pulling on the other non-Microsoft like Gmail or Yahoo mail addresses.

  WLM will work perfectly with these addresses.  Well more than half of my computer 150 customer use WLM 2011 version and it works very well.

• Windows Live Photo Gallery. error: Windows Live Photo Gallery encountered an error loading WLXPhotoviewer.dll and cannot start. 0x8007007e error code

  Windows Live Photo Gallery. error: Windows Live Photo Gallery encountered an error loading WLXPhotoviewer.dll and cannot start. 0x8007007e error code

  Hello

   
  There seems to be a problem with the Windows Live Photo Gallery, it's better to post the same question to the Windows Live Photo Gallery site for assistance. We have a dedicated team to help you with such questions.
  Windows Live Gallery Portal: http://windowslivehelp.com/product.aspx?ProductID=20
   
  Hope the information is useful.

• Impossible to install World of Warcraft and the error message "Windows cannot access the specified device, path or file. May not permissions to access you the item.

  Original title: Need help ASAP please

  Hi all

  I am currently running windows 7 and recently I met a problem that has been giving me the error code: 0 x 80070043 and the Error Message: Windows cannot access the specified device, path or file. You can't have appropriate permission to access the item'. When you try to run a Setup.exe for world of warcraft. But the thing is I am the administrator of the computer and have not had this problem in the neck, it is their all settings or something I can do to fix this? any help would be greatly appreicated thanks and God Bless.

  Hello Jay,
  Thanks for posting your question in the Microsoft Community forum.
  The description of the problem, I see that you are unable to install World of Warcraft and error message "Windows cannot access the specified device, path or file. You can not have appropriate permission to access the item".»

  This problem may occur if you do not have permissions for the file or the location of the file, if the file is located on a site that is not accessible at the moment as a network location or an external drive that is not currently connected to the computer or your antivirus software may block the file.

  Don't worry; Let's try a few steps that will help you solve the problem.

  Method 1:
  I suggest you run the fix it and check if it helps.

  Solve problems with programs that cannot be installed or uninstalled
  http://support.Microsoft.com/mats/program_install_and_uninstall

  Method 2:
  If the problem persists, I suggest you try the procedure described in the article and see if it helps.

  Error "Windows cannot access the specified device, path or file" when you try to install, update or launch a program or file
  http://support.Microsoft.com/kb/2669244
  You can check the links for more information:

  Install a program
  http://Windows.Microsoft.com/en-us/Windows7/install-a-program

  Install programs: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/installing-programs-frequently-asked-questions

  Get back to us and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence.