Citrix UDP broadcast through PIX525

Similar Questions

• PSC disconnected in MAX but meets the UDP broadcasts

  Hey guys,.

  I have 4 controllers of PCP in the control of a whole bunch of sensors on the ground. Each sensor has its own calibration, and so I built an OO hierarchy based on dynamic distribution to cope. Now, there is a piece of generic software and 4 controllers use to perform their tasks (acquisition and newspaper). The first large work three controllers and run everyday, the fourth died within an hour of running. It's the exact same architecture and the code on the controllers.

  I have a thread separate from the network that sends data to the device via a UDP port health - it it broadcasts to the network (CPU utilization, Uptime, HARD disk space). For the fourth controller, I will notice you after an hour it is disconnected to the MAX, I can't FTP in there, I can't connect through the LabVIEW project, BUT this wireless network is still alive and broadcast on the network.

  Can someone answer the following two questions?

  (1) in regard to being active - broadcast signal why is this exactly? I can't move on through MAX or the FTP server...
  (2) regarding the crash of the fourth controller-> the fourth controller has some complex calculations where he tries to determine the root of a polynomial. The NI_AALPro of the Toolkit OR serves that and is quite heavy. There's even a call to the DLL. I have a suspicion that these VI is originally the RT controller to plant. I'll check tomorrow by turning off in the code, but someone at - it does this kind of thing before and are having problems?

  Thank you!

  Hey guys,.

• Impossible to receive packets from UDP broadcast on a PPP connection

  I'm fighting for two days now with no success. I have two modems (don't ask, some special stuff), which uses the dial-up access (PPP). I tried on windows XP and it works like a charm. I'll send unicast and broadcast UPD packets. If I repeat that on Windows 7, I can send only the data of unicast, broadcast packets seems to be lost somewhere, I tried to use the Microsoft network monitor, and I can see that broadcast packets are received on my PPP connection. But after that, they are gone. Somewhere in the kernel. I don't really understand why. I've disabled the firewall, antivirus, motor base, tried to open a session of abandoned filtering packed in the Windows Filtering Platform, clean the WIN7 machine I tried all without success.

  Here is an example of a packet received on the interface, but there most recent scope of my application:

  No.     Time               Source                Destination           Protocol Length Info
        1 13:20:56.093380000 192.168.1.50          192.168.1.255         UDP      49     Source port: x11  Destination port: x11
  
  Frame 1: 49 bytes on wire (392 bits), 49 bytes captured (392 bits)
      Encapsulation type: Ethernet (1)
      Arrival Time: May  7, 2014 13:20:56.093380000 Central Europe Daylight Time
      [Time shift for this packet: 0.000000000 seconds]
      Epoch Time: 1399461656.093380000 seconds
      [Time delta from previous captured frame: 0.000000000 seconds]
      [Time delta from previous displayed frame: 0.000000000 seconds]
      [Time since reference or first frame: 0.000000000 seconds]
      Frame Number: 1
      Frame Length: 49 bytes (392 bits)
      Capture Length: 49 bytes (392 bits)
      [Frame is marked: False]
      [Frame is ignored: False]
      [Protocols in frame: eth:ip:udp:data:vssmonitoring]
      [Coloring Rule Name: UDP]
      [Coloring Rule String: udp]
  Ethernet II, Src: ae:4e:20:00:01:00 (ae:4e:20:00:01:00), Dst: Xerox_00:00:00 (01:00:01:00:00:00)
      Destination: Xerox_00:00:00 (01:00:01:00:00:00)
          Address: Xerox_00:00:00 (01:00:01:00:00:00)
          .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default)
          .... ...1 .... .... .... .... = IG bit: Group address (multicast/broadcast)
      Source: ae:4e:20:00:01:00 (ae:4e:20:00:01:00)
          Address: ae:4e:20:00:01:00 (ae:4e:20:00:01:00)
          .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default)
          .... ...0 .... .... .... .... = IG bit: Individual address (unicast)
      Type: IP (0x0800)
  Internet Protocol Version 4, Src: 192.168.1.50 (192.168.1.50), Dst: 192.168.1.255 (192.168.1.255)
      Version: 4
      Header length: 20 bytes
      Differentiated Services Field: 0x00 (DSCP 0x00: Default; ECN: 0x00: Not-ECT (Not ECN-Capable Transport))
          0000 00.. = Differentiated Services Codepoint: Default (0x00)
          .... ..00 = Explicit Congestion Notification: Not-ECT (Not ECN-Capable Transport) (0x00)
      Total Length: 34
      Identification: 0x0032 (50)
      Flags: 0x00
          0... .... = Reserved bit: Not set
          .0.. .... = Don't fragment: Not set
          ..0. .... = More fragments: Not set
      Fragment offset: 0
      Time to live: 126
      Protocol: UDP (17)
      Header checksum: 0xb817 [correct]
          [Good: True]
          [Bad: False]
      Source: 192.168.1.50 (192.168.1.50)
      Destination: 192.168.1.255 (192.168.1.255)
      [Source GeoIP: Unknown]
      [Destination GeoIP: Unknown]
  User Datagram Protocol, Src Port: x11 (6001), Dst Port: x11 (6001)
      Source port: x11 (6001)
      Destination port: x11 (6001)
      Length: 14
      Checksum: 0xafd1 [validation disabled]
          [Good Checksum: False]
          [Bad Checksum: False]
  Data (6 bytes)
  
  0000  34 34 34 34 34 34                                 444444
      Data: 343434343434
      [Length: 6]
  VSS-Monitoring ethernet trailer, Source Port: 127
      Src Port: 127
  

  I'm out of my ideas, if anyone could help with any idea, please do. I don't know if this possibility is removed on win7 or not.

  Hello

  I suggest you to report your query in the TechNet forums to improve assistance in this regard.

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

  Hope this information helps.

• Check the connections TCP & UDP host through ACL

  Hello!

  I use ACL to control TCP UDP & connections pass through my router (C805 & C2500). I plan to control of the host, but after I have created a new ACL that and add it on IP Access-Group of my Serial interface, the acl that I add before who is used to control the connections TCP & UDP is removed because of an ACL. How can I handle this?

  What you have is a standard access list, which would block anything with the source 127.0.0.1 address and an access list more extended negates several types of traffic.

  To combine I would rewrite the access list standard as a broader access list:

  access-list 100 deny ip 127.0.0.1 host everything

  who deny packets whose source 127.0.0.1 address.

  I would put rewriting stated as first statement in the new list access followed by others which would give you this:

  Note 100 access list refuse the specific host

  access-list 100 deny ip 127.0.0.1 host everything

  Access-list 100 remark block number TCP and UDP ports

  access list 100 permit tcp any any eq www

  access-list 100 permit tcp a whole Workbench

  access-list 100 tcp refuse any any eq 135

  access-list 100 tcp refuse any any eq 445

  access-list 100 tcp refuse any any eq 593

  access-list 100 deny udp any any eq 135

  access-list 100 deny udp any any eq tftp

  access-list 100 deny udp any any eq netbios-ns

  access ip-list 100 permit a whole

  That should do it.

  HTH

  Rick

• Create a broadcast UDP socket and wait to receive a message.

  I am developing a Playbook application using Adobe Air SDK.

  I want to create an application that opens a UDP broadcast socket and wait to receive a message.

  Is it possible to do it with Adobe Air SDK?

  By Adobe documents, it appears profile still not mobile support (I put the filter on the reference of the API for 'AIR earlier 3.1 and runtime').  Note the class property available to test you support when running.

  http://help.Adobe.com/en_US/FlashPlatform/reference/ActionScript/3/Flash/NET/DatagramSocket.html

  "AIR profile support: this feature is supported on all systems of desktop operating, but is not supported on mobile devices or AIR to TV sets." You can test the support at run time by using the DatagramSocket.isSupported property. See AIR profile taken in charge for more information regarding the API across multiple profiles support. »

• Citrix GoToWebinar: Register participating new field?

  Hello

  "We regularly use the Citrix GoToWebinar: connector of participating register Cloud, but when I went to set up a Friday he gave me an additional option of field Citrix,"Joined Key", in the mappings of" article that was never there before. Someone knows what this field is or does? Normally, map us the field of Webinar meeting URL Citrix through a field of Eloqua Contact and use it on the registration confirmation email we send to registrants. If the key of the registered person is just a unique identifier in Citrix us map through because we don't need, but I'm worried in case it is something which the registrant must then be able to connect to the Webinar on the day.

  Does anyone have answers or ideas on this? I raised with Eloqua and Citrix support on this requests, but thought if someone has a first-hand experience that would be really helpful!

  Thank you

  Karine

  Hi Mika,

  It is a new field that has been added, and it is simply the unique ID of the registrant in the Citrix system.  It is completely optional, but was something that was requested by some customers.

  See the discussions at the bottom of the second page here install the GoToWebinar App of the AppCloud

• Tool to watch how an application interacts with the OS network stack?

  I have a third-party commercial application that sends a UDP broadcast and waits for a response from machines on the same network.  It works fine when only one card NETWORK interface (we'll call it "primary") is enabled but if I enable the 'secondary' adapters fails.  It seems that the problem is in how the application is to determine what NETWORK card to use.  Y at - it a tool that would let me ask questions or look at what made the app to determine what NETWORK card to send traffic on?  I took the Wireshark traces and that showed me the traffic but I need something that will give me more information at an earlier stage of the process.  I also watched some of the Sysinternal tools and wasn't sure if one of those who do the trick.  Looks like I need to look at the app launch and watch it somehow to go through the process of selecting an interface to use.  Is this possible?

  OS is WinXP and/or Win2008 32 or 64-bit.

  Hello

  I recommend you post the question in the Windows Server Forums.

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer

  Thanks and greetings
  Umesh P - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• Problems with SmsDemo

  Hello

  I try to run SmsDemo.

  I imported the sample SmsDemo and I have the server, account component. I run the server component, but the messages that I send to the application of SmsDemo have no effect - I don't see anything happen to the account application. I have disabled the Windows Firewall without effect.

  I also tried connecting two instances of the emulator, different work, with the source and destination directories through ports mapped as suggested. I can see the ports UDP listen when I netstat but no message never reaches the other emulator so I try and send the application SMSDemo.

  There is no documentation actually describing what you need to do to get this sample running - I am at a loss trying to understand how to remedy this situation.

  1. do I need to define the arguments for the sms source port and destination on the emulator?

  2 should I configure anything in the account application to compare the port information in the client application?

  3 must run the MDS Simulator to make this work?

  4. can I simulate a device for sending SMS to the emulator running a normal application and J2SE using datagrams, as does the application of account?

  Any help would be greatly appreciated.

  Will be

  I finally found a solution for the problem. Here it is:

  Using Wireshark to sniff the UDP broadcast from the emulator, I noticed that the destination address is incorrect - his "1.0.0.127. This address is not routable, so the datagram sent from an emulator will never reach the other emulator.

  I might have missed, but I don't see any command line argument to set when you launch the emulator to specify the destination address.

  I changed my development laptop to use a hardcoded instead of DHCP IP address. I then added 1.0.0.127 under another IP address my TCP/IP settings. Now, the address is routable.

  Restarted the two emulators without changing the port settings (/ sms-source-port and/sms-destination-port still a mapping croiseent correctly) and it worked fine. I don't have to use the SMSDemo application. I used the Blackberry normal mail app.

  I hope this helps others who face this same problem.

• iTunes library to external hard drive works on pc and mac

  Hello world

  I have 1 pc and mac 2. I also use the music library to icloud. However, it depends on the internet connection.

  so, I was wondering if I can put the "itunes library" file on each laptop, the "itunes media" while on the external hard drive?

  My idea is to use an external hard drive whenever I want to use the laptop. so I don't need to broadcast through library icloud music. Moreover, I need an external hard drive and itunes library to work on pc and mac.

  Cheers!

  See make a library of portable split. You will need either a for OS X NTFS driver or driver for HFS + for Windows in order to use the drive with an operating system. Also note that there is a delay when you first launch after passage of one BONE to the other.

  TT2

• Pavilion 27xw & Envy 15 laptop: how to keep sound when connected to the laptop

  Have a laptop 15.6-inch Envy running on Windows 10 and rose just a monitor 27 xw Pavilion, they are connected by a HDMI cable included with monitor
  
  If there is sound broadcast when I connect the HDMI cable it continues to broadcast through the speakers on the laptop, but if it stops then it don't re - start not to broadcast while connected.  If I disconnect the monitor then the sounds spread through the laptop.

  How to work around this problem?

  Jimmy, welcome to the forum.

  You must connect the monitor to the laptop and go to control panel / sound.  You must make sure that the speakers to the monitor are set by default.  If you do not use the monitor all the time, you may need to do this every time you connect it.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• 5660 want: Fast/Economical printing want 5660

  We wanted the 5660 only about three months and were broadcast through extremely fast ink while printing very little.  We tried to change the print preference settings, but the preference for economy printing is locked and unavailable.  I tried to create a new shortcut to preference impression with the draft definition, however he continued to print with the same resolution as the normal setting.  Is there a way to change this?

  Hello!
  Welcome to the HP community @dentistom,

  I saw your post on trying to change the print settings for book on ink and wanted to tender hand. My best advice would be to check the image/link below and select the steps to "change the default for all printing print settings', allowing that each work is printed in draft mode without returning to print in 'normal' after each use. If you have already tried to do as a result, of course the printer is directly connected to socket, avoiding bars power and surge protectors. If you think there may be a hardware defect, contact HP to inquire about a replacement unit.

  Changing the settings to print in Windows 7

  
  
  If you have trouble, let me know and I'll do my best to help.
  
  Click on the "accept as Solution" If the issue has reached a resolution! Hit thumbs up below like my post or show thanks to me to lend a hand!
  
  We wish you a wonderful day

  Contact HP:
  
  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on: contact HP options - click Get phone number
  File number and phone number appear

• How to change the default preset list of radio stations IP Journe air 1000

  I just bought a Journe air 1000.
  I bought this product in order to listen to radio IP in addition to visualize the sideshows.

  In the manual it says that there is no Mode for Radio IP (access to the SHOUTcast Protocol, with the default channels 30-50)

  Although these default channels 30 to 50 is not bud, I was wondering how to set other radio stations that are broadcast through SHOUTcast radio in the pre-defined list and delete some of the existing presets.
  I think that this should be possible, otherwise support toshiba would not give a range of channels, but rather a fixed number of presets. Unless they expect that 40% of the presets will cease broadcasting in the future.

  I tried to use the search function, but it seems to look among the preset radio stations. In addition, this search operation is not very practical. I can't imagine doing this whenever I want to hear my favorite stations.

  To this end, I would like to save my own presets from 2-3 and clear the rest.

  There someone now how to set its own presets?

  Another question would be:
  Anyone know what operating system uses this framework. I am interested in tweaking, and this information would help me look in the appropriate bodies on how to do it.

  Hello amosxo,

  to set your favorite radio stations, you must do the following:
  1 make a Wifi connection to the Air1000
  2. choose 'Radio '.
  3. Press 'OK'--> the keyboard is displayed
  4 type the name of the radio channel you want to record
  5. choose the right channel in the list by going down with the cursor
  6. press on the symbol of the heart - set the radio channel in the folder 'My Favorites '.

  I think that it is not possible to remove the default radio channels.

  I Don t know what operating system is used in the Air1000.

  hope this helps you

  Best regards

• iPod touch 4th generation does not not with xcarlink

  Can anyone help. I have recently purchased an iPod touch 4th generation for use with the xcarlink iPod interface. I can't seem to make it work either comes up with is not compatible for loading! Can I get nt music broadcast through your car stereo speakers, but an older iPod worked fine and my iPod 2. Y at - it something I am doing wrong? Y at - it connectors adapter that I can buy to fix this very annoying? Can anyone help?

  Sometimes it works:

  -Reset the device iOS. Nothing will be lost

  Device iOS Reset: Hold down the On / Off button and the Home button at the same time for to

  less than ten seconds, until the Apple logo appears

  -Reset all settings

  Go to settings > general > Reset and tap reset all settings.

  All your preferences and settings are reset. Information (such as your contacts and calendars) and media (such as songs and videos) are not affected.

  -Restore from backup. See:

  Restore your device from an iCloud or iTunes backup - Apple Support

  -Restore factory settings/new iOS device.

  However, xcarlink is old and not infrequently an iOS update/new model iPod case compatibility.     All I can find on the site of xcarlink is:

  (6) support iPod 3, iPod 4, Nano, Nano 3, video, Mini, Classic, Touch, iPhone

• The CPU usage rises, more than a few hours until the application crashes

  I wrote an application to control the antennas of the ship. I met all the requirements of the customer. However, when I run my application the CPU starts around 13% (depending on the mode) and slip about 5% every 30 minutes, until finally the use reached 100% and not surprisingly the application stops responding.

  My application communicates with the antenna via the serial connection. I have an interface for a remote connection via the local area network that uses the TCP protocol and I broadcast UDP packets on the local network for use by other ship systems (sharing data such as ships Cap etc.). The 3rd party who wrote the remote application used my UDP broadcast as a way to receive data from my application.

  My application has several vi. Should I these zip and attach?

  Any help or pointer as to why its use goosebumps would be welcome. My initial feeling is that a buffer is full to bursting, but where and who? I use tax filers to communicate between the loops and have a few global variables that communicate my menu selection.

  Thank you

  Steve

  Steve S of a. in writing:

  It is certainly my application.

  I noticed that I got from reporters that contain groups inside a loop and have not released. If the Notifier is created each iteration and not released, this would cause the problem?

  WELL YES!

  Resources should be allocated (created declarant) before the loops, then a ref use din the loop. Only when the loop is complete must it be closed.

  Your zip code if you want us to look more closely.

  Ben

• cannot change the process unique network released (cleared)

  I have software running on a fieldpoint which normally runs standalone but I need to run a simulator to debugging on a windows computer. The RT software uses several shared single process variables that are deployed to the target. In order to launch the simulator that accesses screw has also deployed to the target, I also access these variables on the windows machine (but only during the simulation).

  I thought I could do this simply by changing the shared variables 'unique process', "network broadcast" through their properties dialog. However, when I access those variables, the network published option is grayed out. Does anyone know why this is? I prefer not having to recreate these variables from scratch, they are connected in several places in the application.

  I have included the library file that contains these variables, in case anyone knows anything I put in it that prevents the change to the published network.

  Hi Kgolden

  The reason that you are not able to select the network has published is because the refnum of queue is not a data type that can be sent via a published network shared variable.