Classic question: SSL VPN Client and Vista 64 - bit OS

Similar Questions

• Question about Satellite L40 and Vista 32 bit

  Hey all, I have the following problem.
  I have Satellite L40 series 2 PC and tried to install vista ultimate 32 bit, and they freeze only on the process of "complete installation."
  I read in some other forums and found it is not only my problem. I tried with 64 bit ultimate, it's all OK. It may be, the main problem is that it is not possible to install VISTA 32 bit.
  I only ultimate now, so my question is if anyone knows or installed to another type of Vista 32 bit on these series?

  Thanks before

  As far as I know that all new models of Toshiba laptops come with Vista 32 bit. Satellite L40 is offered in three different models, and each one also comes with 32-bit operating system. If you have the recovery DVDs with your laptop is Vista 32 - bit OS. I assume it must be the Home Premium version.

  I don't have a model L, but my model works well on Vista Ultimate.

• Windows IPSEC and SSL VPN client on the same machine

  Matches (coexistence) installation of IPSEC and SSL vpn clients that are supported on the same computer, windows (XP and Win7)?

  As mentioned by Patricia and Jennifer (5 stars), you can install two clients on the same machine without any problem.

  The tricky part comes when you are trying to connect two clients at the same time, that's when you may encounter unexpected problems.

  However, if your intention is to install both clients and connect them individually and not at the same time, you'll be fine.

  If you have any other questions, please mark this question as answered and note all messages that you have found useful.

  Thank you.

  Portu.

  Post edited by: Javier Portuguez

• SSL VPN Client username and passwords save

  Hello

  We use SSL VPN with ASA, we want to save the user name and password to connect to the customers in the SSL VPN client, if user only has not to type again to connect to the enterprise resources, employees normally use iPhone IOS and Android for VPN access.

  Is their a way, we can save the credentials username and password for iphone and android?

  I googled for it and found a way using URIS to pre-fill the name of user and password but I'm not sure how it works, and it will be beneficial.

  http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...

  Hello

  You can use the URIs, if your method of methods must use WBS for the password pre-population.

  I would recommed you use certificate authentication, so they don't have to use the user name and password, and the process will be done automatically.

  You can take a look at this Document that created one of my peers:

  - https://supportforums.cisco.com/blog/152941/anyconnect-certificate-based...

  He has the details you will need.

  Don t forget to rate and score as correct the helpful post!

  David Castro,

  Kind regards

• THE SSL VPN CLIENT ERROR!

  VPN concentrator running 4.7. I have to connect to the web vpn session. The SSL VPN Client installs. Message that says: "so that the SSL VPN connection is pending" and later another message appears that says "HTTP RESPONSE received from gateway SSL VPN is not valid" appears.

  What is strange is that the VPN concentrator lists me as it is connected with an IP address assigned to the ACS, but I can't access anything whatsoever. BTW, no ACLs WEB or IP filters are configured for this group that would not allow me access to the network. In addition, with the same information identification and the same group, I have no problem to access the network when the client SSL VPN is not configured to be used. IE web vpn before 4.7.

  Any ideas?

  The "VPN SSL HTTP RESPONSE received from gateway is incorrect" message may appear if the configuration of the client of the concentrator contains over split tunneling 26 entries.

• SSL VPN Client - version 4.7 WebVPN session is over; Port error.

  Hi, I just upgraded to 4.7 and trying of the SSL VPN Client.

  He seems to spend the largest part of the installation on client machines. I tried more than one, ut I get this error from port.

  Any ideas?

  Try asigning the user, an ip address on the hub

• SSLVPN package SSL-VPN-Client (seq:1): installed error: others

  "Try to install the package anyconnect-victory - 2.5.2019 - k9.pkg on a Cisco 1811 running c181x-advipservicesk9 - mz.124 - 22.T5.bin router, when I run the command in config mode" webvpn install flash: anyconnect svc - win - 2.5.2019 - k9.pkg ' I get "

  "SSLVPN package SSL-VPN-Client (seq:1): installed error: others" some proposed to reformat the flash drive, does anyone know a workaround or a way to do it without losing the configuration running?  I think that there is a problem with the structure of files on the router, the installation package is capable of "webvpn" installation directory.  All ideas are welcome, thanks!

  hostname #sh flash
  -# - length - time - path
  1 23472512 February 23, 2012 21:10:34 c181x-advipservicesk9 - mz.124 - 22.T5.bin
  2 0 23 February 2012 21:37:50 webvpn
  3 4686889 23 February 2012 21:18:46 anyconnect-victory - 2.5.2019 - k9.pkg

  3772416 bytes available (28168192 bytes used)

  Processor of 1811 (MPC8500) Cisco (revision 0 x 400) with 118784K / 12288K bytes of memory.
  10 FastEthernet interfaces
  Serial 1 interface
  1 line of terminal
  31360K bytes of ATA CompactFlash (read/write)

  Configuration register is 0 x 2102

  Host name #.

  I think it's because you have not enough space - he's trying to copy the file to the directory of webvpn.

  Make sure that the install webvpn command isn't in your configuration.

  Move the anyconnect package in the directory of webvpn

  run

  WebVPN install svc flash:/webvpn/anyconnect-win-2.5.2019-k9.pkg

  And see if that helps.

• Cisco VPN Client and Windows XP VPN Client IPSec to ASA

  I configured ASA for IPSec VPN via Cisco VPN Client and XP VPN client communications. I can connect successfully with Cisco VPN Client, but I get an error when connecting with the XP client. Debugging said "misconfigured groups and transport/tunneling mode" I know, they use different methods of transport and tunneling, and I think that I have configured both. Take a look at the config.

  PS a funny thing - when I connect with client VPN in Windows Server 2003, I have no error. The only difference is that client XP is behind an ADSL router and client server is directly connected to the Internet on one of its public IP of interfaces. NAT in the case of XP can cause problems?

  Config is:

  !

  interface GigabitEthernet0/2.30

  Description remote access

  VLAN 30

  nameif remote access

  security-level 0

  IP 85.*. *. 1 255.255.255.0

  !

  access-list 110 scope ip allow a whole

  NAT list extended access permit tcp any host 10.254.17.10 eq ssh

  NAT list extended access permit tcp any host 10.254.17.26 eq ssh

  access-list extended ip allowed any one sheep

  access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh

  sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0

  tunnel of splitting allowed access list standard 192.168.121.0 255.255.255.0

  flow-export destination inside-Bct 192.168.1.27 9996

  IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0

  ARP timeout 14400

  global (outside-Baku) 1 interface

  global (outside-Ganja) interface 2

  NAT (inside-Bct) 0 access-list sheep-vpn

  NAT (inside-Bct) 1 access list nat

  NAT (inside-Bct) 2-nat-ganja access list

  Access-group rdp on interface outside-Ganja

  !

  Access remote 0.0.0.0 0.0.0.0 85.*. *. 1 2

  Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1

  Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1

  Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1

  Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1

  Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1

  Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1

  Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1

  Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1

  dynamic-access-policy-registration DfltAccessPolicy

  Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT

  Crypto ipsec transform-set newset aes - esp esp-md5-hmac

  Crypto ipsec transform-set esp-3des esp-md5-hmac vpnclienttrans

  Crypto ipsec transform-set vpnclienttrans transport mode

  Crypto ipsec transform-set esp-3des esp-md5-hmac raccess

  life crypto ipsec security association seconds 214748364

  Crypto ipsec kilobytes of life security-association 214748364

  raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

  vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1

  card crypto interface for remote access vpnclientmap

  crypto isakmp identity address

  ISAKMP crypto enable vpntest

  ISAKMP crypto enable outside-Baku

  ISAKMP crypto enable outside-Ganja

  crypto ISAKMP enable remote access

  ISAKMP crypto enable Interior-Bct

  crypto ISAKMP policy 30

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  No encryption isakmp nat-traversal

  No vpn-addr-assign aaa

  Telnet timeout 5

  SSH 192.168.1.0 255.255.255.192 outside Baku

  SSH 10.254.17.26 255.255.255.255 outside Baku

  SSH 10.254.17.18 255.255.255.255 outside Baku

  SSH 10.254.17.10 255.255.255.255 outside Baku

  SSH 10.254.17.26 255.255.255.255 outside-Ganja

  SSH 10.254.17.18 255.255.255.255 outside-Ganja

  SSH 10.254.17.10 255.255.255.255 outside-Ganja

  SSH 192.168.1.0 255.255.255.192 Interior-Bct

  internal vpn group policy

  attributes of vpn group policy

  value of DNS-server 192.168.1.3

  Protocol-tunnel-VPN IPSec l2tp ipsec

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value split tunnel

  BCT.AZ value by default-field

  attributes global-tunnel-group DefaultRAGroup

  raccess address pool

  Group-RADIUS authentication server

  Group Policy - by default-vpn

  IPSec-attributes tunnel-group DefaultRAGroup

  pre-shared-key *.

  Hello

  For the Cisco VPN client, you would need a tunnel-group name configured on the ASA with a pre-shared key.

  Please see configuration below:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  or

  http://tinyurl.com/5t67hd

  Please see the section of tunnel-group config of the SAA.

  There is a tunnel-group called "rtptacvpn" and a pre-shared key associated with it. This group name is used by the VPN Client Group name.

  So, you would need a specific tunnel-group name configured with a pre-shared key and use it on the Cisco VPN Client.

  Secondly, because you are behind a router ADSL, I'm sure that's configured for NAT. can you please activate NAT - T on your ASA.

  "crypto isakmp nat-traversal.

  Thirdly, change the transformation of the value

  raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

  Let me know the result.

  Thank you

  Gilbert

• VPN client and contradictory static NAT entries

  Hello, we have a VPN IPSEC implemented on a router for remote access. It works very well, for the most part. We have also a few PAT static entries to allow access to a web server, etc. from the outside. We deny NATting from the range of IP addresses for the range of VPN client and it works except for entries that also have PAT configurations.

  So, for example, we have web server 10.0.0.1 and a PAT redirection port 10.0.0.1: 80 to the IP WAN port 80. If a VPN client tries to connect to 10.0.0.1: 80, the syn - ack packet back to the customer WAN IP VPN on the router! If the VPN client connects to the RDP server 10.0.0.2:3389, it works very well that this server is not a static entry PAT.

  Is there a way to get around this?

  Thank you!

  There is a way to get around, use the same settings you have for your dynamic nat in your nat staitc entries, something like this:

  Currently, it should show as:

  IP nat inside source static XXXXX XXXX 80 80

  you need to take it

  IP nat inside source static 80 XXXX XXXX 80 map route AAAA

  When your itinerary map YYY refers to something with an acl that you refuse traffic from inside your router for the pool of vpn

  IP Access-list ext nonat

  deny ip 10.0.0.0 0.0.0.255

  Licensing ip 10.0.0.0 0.0.0.255 any

  route allowed AAAA 10 map

  match ip address sheep

  You even need all the static PAT

  HTH

  Ivan

• Install Windows 7 64 bit and Vista 32 bit on the same drive

  I have Vista 32 bit installed on my laptop. Media recovery is on a recovery partition, I have no recovery DVD such as $85 for something that should be included with my expensive laptop anyway, it is a bit much

  I have a drive to upgrade Windows 7 from my laptop manufacturer that allows me to each upgrade or to start from scratch.

  I want to install Windows 7 64 bit on a separate partition for the installation of my 32-bit Vista, but when I boot on the DVD there is no option to select the 32 or 64 bit, it only allows me to install the 32-bit version. I have partitions installed correctly then they arnt the problem. If I try to boot from the recovery partition to install Vista 64 bit on a separate partition, to upgreade can leave, he simply don't say so, it doesn't allow the recovery or replacement of my existing Vista installation. Also, often when I boot to recovery mode, by organizing 0 start up, he simply waits some time and the Vista of boots in any case.

  How should I do to dual boot Windows 7 64 bit and Vista 32-bit, as all possible ways I have tried do not work, and I can't afford to buy the madmen of... Toshiba recovery media ?

  The 'disc Windows 7 from the manufacturer of your laptop upgrade' can be used to improve the qualification system of operating from 32-bit of Windows Vista that was originally installed on the laptop.  It cannot be used for any other configuration or purpose. Carey Frisch

  Actually, this isn't just a "upgrade drive" it's a full disc of Windows 7, I know that I can install full Windows 7 32 bit in a separate partition for Vista.

  The problem is solved in any case, I managed to hide my Vista (C) install with Acronis and boot to the WIndows 7 DVD. It then allowed me to install Windows 7 64 bit on the other Partition, because he did not think that 32-bit Windows Vista has been installed on the HARD drive. I managed to deceive it by showing the menu options of 32 bits or 64 bits in this way... I assumed it was a protection system put in place by Microsoft to stop upgrade problems if soemone tried upgrade Vista 32, Windows 7 64

  Now under Vista 32 and Widnws 7 64 on the same computer.

• Synchronization and Vista 64-bit

  I have a Palm TX and Vista 64-bit and having synchronization problems (do not recognize the device when I try to synchronize).  I couldn't install the original/old version of the software (v 4.1.2 I think) and downloaded v 6.2.  Installed, it cannot synchronize.  I tried what you said worked for you by opening the Palm as an administrator, but that made no difference to me.  If anyone knows other alternatives, it would be appreciated.

  How you try to synchronize?  Via USB?  It can be done this way, as mentioned in dozens of discussions here...

  You have a wireless network set up in your home?  I wrote a file "how to sync a Tx via Wifi with Vista64" above it "sticky" gray display at the top of this section of the forum.   I use this method with my Vista 64 bit laptop easily!

  WyreNut

• Issue of SSL Vpn client'

  you are not sure if it's possible/Device asa 5550 - but a customer can establish SSL VPN to the remote network and devices on the local network to access remote network printers?

  so you have a network client that creates an SSL VPN to network B network B configurable so that the automatic work met the same vpn ssl to a different IP address?

  I don't know if its just me, but I don't understand what you mean with that:

  so you have a network client that creates an SSL VPN to network B network B configurable so that the automatic work met the same vpn ssl to a different IP address?

  You can try to explain once more?

  Now I think tell you the following, please look at this:

  HQ - ASA - INTERNET - office2

  Now the office2 will a clientless vpn SSL to the ASA and subsequently, you want HQ in order to communicate with certain printers or servers to Desktop 2 via SSL vpn without customer... If that's the question the answer is no. clientless vpn SSL will only allow traffic to go from office2 at HQ and not all traffic , this will depend on which allows you to configure the clientless ssl (Smart tunnels, Port-forwarding, Plugins).

  Yet once I don't know if that is the question.

  Kind regards

  Julio

  Note all useful posts

• Routing problem between the VPN Client and the router's Ethernet device

  Hello

  I have a Cisco 1721 in a test environment.

  A net 172.16.0.0/19 simulates the Internet and a net 192.168.1.0/24 simulates the net, the VPN tunnel must go to (intranet).

  The net 172.16.0.0 depends on the router 0 FastEthernet, Intranet (VPN) hangs on Ethernet 0.

  The configuration was inspired form the sample Configuration

  "Configuring the Client VPN Cisco 3.x for Windows to IOS using Local extended authentication"

  and the output of the ConfigMaker configuration.

  Authentication and logon works. Client receives an IP address from the pool. But there's a routing problem

  side of routers. Ping client-side - do not work (the VPN client statistics that count encrypt them packets, but not to decrypt).

  Ping the router works too, but decrypt and encrypt customer statistics in VPN packets count progressive

  (customer has a correct route and return ICMP packets to the router).

  The question now is:

  How to route packets between the Tunnel and an Ethernet device (Ethernet 0)?

  conf of the router is attached - hope that's not too...

  Thanks & cordially

  Thomas Schmidt

  -.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- snipp .-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.

  !

  version 12.2

  horodateurs service debug uptime

  Log service timestamps uptime

  encryption password service

  !

  !

  host name * moderator edit *.

  !

  enable secret 5 * moderator edit *.

  !

  !

  AAA new-model

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  !

  ! only for the test...

  !

  username cisco password 0 * moderator edit *.

  !

  IP subnet zero

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  crypto ISAKMP policy 3

  3des encryption

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group 3000client

  key cisco123

  pool ippool

  !

  ! We do not want to divide the tunnel

  ! ACL 108

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  interface Ethernet0

  no downtime

  Description connected to VPN

  IP 192.168.1.1 255.255.255.0

  full-duplex

  IP access-group 101 in

  IP access-group 101 out

  KeepAlive 10

  No cdp enable

  !

  interface Ethernet1

  no downtime

  address 192.168.3.1 IP 255.255.255.0

  IP access-group 101 in

  IP access-group 101 out

  full-duplex

  KeepAlive 10

  No cdp enable

  !

  interface FastEthernet0

  no downtime

  Description connected to the Internet

  IP 172.16.12.20 255.255.224.0

  automatic speed

  KeepAlive 10

  No cdp enable

  !

  ! This access group is also only for test cases!

  !

  no access list 101

  access list 101 ip allow a whole

  !

  local pool IP 192.168.10.1 ippool 192.168.10.10

  IP classless

  IP route 0.0.0.0 0.0.0.0 172.16.12.20

  enable IP pim Bennett

  !

  Line con 0

  exec-timeout 0 0

  password 7 * edit from moderator *.

  line to 0

  line vty 0 4

  !

  end

  ^-^-^-^-^-^-^-^-^-^-^-^-^- snapp ^-^-^-^-^-^-^-^-^-^-^-^-^-^-

  Thomas,

  Can't wait to show something that might be there, but I don't see here. You do not have the card encryption applied to one of the interfaces, perhaps it was not copied. Assuming your description you do it, or should it be, applied to the fa0 and you are connected. Try how you ping? Since the router or a device located on E0? If you ping the router, you will need to do an extended ping of E0 to the ip address of the client has been assigned. If your just ping the router without the extension, you will get sales and decrypts that you declare on the client. Have you tried to ping from the client to interface E0? Your default route on the router is pointing to fa0? You have a next hop to affect? You have several NIC on the client pc? Turn off your other network cards to check that you don't have a problem with routing on the client if you have more than one.

  Kurtis Durrett

• Remote VPN client and Telnet to ASA

  Hi guys

  I have an ASA connected to the Cisco 2821 router firewall.

  I have the router ADSL and lease line connected.

  All my traffic for web ports etc. of ADSL ftp and smtp pop3, telnet etc is going to rental online.

  My questions as follows:

  I am unable to telnet to ASA outside Interface although its configuered.

  Unable to connect my remote VPN Client, there is no package debug crypto isakmp, I know that I have a nat that is my before router device my asa, I owe not nat port 4500 and esp more there, but how his confusion.

  I'm ataching configuration.

  Concerning

  It looks like a config issue. Possibly need debug output "debug crypto isa 127".

  You may need remove the command «LOCAL authority-server-group»

  NAT-traversal is enabled by default on the ASA 8.x version. So you don't have to worry about NAT device in the middle.

• Where can I get a SSL VPN client?

  I don't know much about vpn technology, but used the cisco 5.x client software and the software vpn client that ships with windows xp. Now a customer asks me to connect using an ssl vpn. I don't think I can do it with either of the vpn client packages I've used before? So what am I supposed to use? I looked openvpn and couldn't make much sense out of it. I registered on this site, but apparently this is not enough for me to access the software vpn ssl client.

  Michael,

  If you are the client establishing the connection to the server RA via SSL the way that it works is using regular internet OS web browser as Internet Exprorer, as it supports SSL as webvpn SSL, and the user credentials to open a session in WEBVPN leads, that's all that you need to connect to the server of your customer RA.

  exmple to connect to the RA through webvpn would be like:

  https://

  There are two things you need as to the requirements, and I quote from the link below.

  Requirements

  Before this configuration, make sure that you follow the conditions for remote client stations:

  SSL compatible Web browser

  SUN Java JRE version 1.4 or newer

  Cookies enabled

  Blockers disabled popups

  Local administrator privileges (only not mandatory but highly recommended)

  Note: The latest version of SUN Java JRE is available as a free download from the Java Web site.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a008072462a.shtml#PREREQ

  PLS note any useful message

  Rgds

  Jorge