Code error-229771

Similar Questions

• Why do I get error-229771

  Hello

  I recently downloaded labview in order to write a scenario that would take measures of voltage of a battery by using the NI USB 6008 case. My code has worked fine until I extended my trial labview for the period of 45 days. I receive the error 229771 making reference to my DAQ assistant. Is it possible for me to solve this problem?

  Thank you

  You search the forum for the error code? There are a few posts showing solutions.

  For some reason you need to leave the sign less for the search to work.

  This could be a good starting point:

  I get error-229771 to Task.vi DAQmx Start?

  Steve

• DAQmx create virtual channel (VI) error-229771 reports

  Hello

  When in a project that I am working to get error-229771 code whenever I try to run 'DAQmx create Virtual Channel (VI)' this does not happen when I create a vi not in a project.  The problem is that this project is very large and it if poster impossible to recreate. It's several hundred vi. Y at - it something that I missed in the forums and support that could explain this. I created the VI below in the project and outside the project. In the project, the error occurs outside the project, it runs without any problems.

  Message:

  229771 error occurred at .vi:1780003 DAQmx create channel (I-voltage-Basic)

  Possible reasons:

  Internal software error has occurred in the MIG software. Please contact the support of National Instruments.

  Task name: _unnamedTask

  Any help would be appreciated.  Thank you, Matt.

  LabVIEW version: 15.052(32bit)

  OR Max Version: 15.0.f0

  NEITHER DAQmx Verson: 15

  OS: windows 7 service pack 1

  PC: Intel Core i7-2600, 8 GB of ram

  Data Aquistion: NEITHER DAQ USB-6289 calibrated June 2015

  This code snippet returns the name of the first channel of analog input on the device first, and then tries to create a task for her. The bed of the canal, then close the task.

  

  Error message

  

  Hi Matthew,

  Thank you for following up after you fix your problem.  I'm glad to hear that you do not encounter this problem more.

  Here is an article that lists the reasons for this error (although unfortunately, I cannot pin down which is the exact cause in this case).

  http://digital.NI.com/public.nsf/allkb/03123D0E8A36C48E862577A4005B6BAA

  NOTE: This article specifies that the error occurs at startup task VI DAQmx.  You do not use the start task VI, so the task starts automatically in the DAQmx Read function.  The error will occur instead in the DAQmx virtual channel create, that you encounter in your error.

  I hope this gives you an idea about what could have gone wrong, and I'm sorry he is no more details.

  Good programming!

• code error-8072

  I can't empty my trash. The operation cannot be completed because an unexpected error has occurred (code error-8072).

  Does anyone have an idea what this error code means? Or better yet, how to fix this?

  Stop

  Unplug your external devices

  Restart in safe mode

  Try safe mode if your Mac does not end commissioning - Apple Support

  Check your hard drive with disk utility

  Using disk utility to check or repair disks - Apple Support

  then empty the trash

  Stop and reconnect the devices and start normally.

  If the problem persists, check your system with AHT

  Using Apple Hardware Test - Apple Support

• How can I fix the code error 56?

  Two years ago, I bought my iPhone6 (to the US Apple store) and I used iPhone6 in South Korea. So, I can't take refurbish here.

  When I was trying to update iso 9.3, pop up code error 56 at the end of the update process. so, I removed the chip from the usim card and tried again. but the pop-up code error 56 again. How can I fix this error?

  Take a look at these articles:

  Solve the iOS update and restore error in iTunes - Apple Support

  Get help with iOS update or restore errors - Apple Support

• Get a zip code error when your book order

  Getting a zip code error when your book order is exact zip code th for my address.

  In the Canada.

  Help

  You order the Canadian Apple store online? If this isn't the case, then you must change your store site online on the Canadian site. Scroll down to the bottom of the page where you should find an icon of circled on the right corner flag. Click it, and then select the Canadian store in the list and re - buy article. It must now accept Canadian postal codes rather than postcodes American.

• Webloc changed Safari icons: code error-10823

  This morning when I turned on my Mac, I noticed that all my Safari webloc icons turned into another (basically @ sign and HTTP in the icon). When I right click the icon's default implementation "Simulator.app (9.2). By tradition, Simulator.app is part of Xcode. However, I've updated or use Xcode or any application that is part of Xcode in the past 2 weeks (approximately).

  Yes, ok, let's change the default application associated with "webloc" icons for Safari. Right-click. Default app for Safari. I get the error shows: "the element is locked or damaged, or in a folder you have not allowed to edit (code error-10823)."

  After removal of the dialog box, I get another dialog stating: " ""the operation cannot be completed. An unexpected error has occurred (code error-10823). »

  I have restart mode without failure. Same question. I can't find something on the code of error-10823 and on why a land I would get this message that the element is locked or damaged.

  Any ideas? Thank you.

  Mac mini end of 2012

  El Crap 10.11.3

  Although the problem is not the same, please follow the instructions in this article to support to reset the launch Services database. Instead of typing the shell command in the article, I suggest that you copy and paste the web page in the Terminal window. Make sure you only select the entire line. One way to do that is triple - click anywhere in the line.

  If you do not already have a current backup, back up all data before proceeding. You should perhaps log out or restart to see a change.

• My iMac news, sharing and permissions had a name 'wheel' that I didn't put there. When I try to delete it, I get code error-8076. Any thoughts?

  My iMac news, sharing and permissions has a name 'wheel' that I didn't put there. When I try to delete it, I get code error-8076. Any thoughts?

  It is a part of the OS and nothing to worry about.

  https://en.Wikipedia.org/wiki/wheel _ (Unix_term)

• My browser is blocked for security reasons. Code error-QFR5000RT11C. My incoming connections in open State distance. Then I got the call from the United States 1 (866)986-3669, I picked up the phone, but they put the phone down. No matter what? Help, plea

  My browser is blocked for security reasons. Code error-QFR5000RT11C. My incoming connections in open State distance. Then I got the call from the United States 1 (866)986-3669, I picked up the phone, but they put the phone down. No matter what? Help, please.

  It's probably a SCAM.  Do not call these numbers.  Force Quit Safari and reopen it by holding down the SHIFT key.

  Ciao.

• Compaq cq10: need help please code error: CNU0015RN9 on compaq cq10 150ev

  Need help please code error: CNU0015RN9

  Thank you in advance!

  Hello
  
  No problem. Did you do a hard reset and try again?
  
  For the error code, check again a time-
  
  Try:
  
  e9l11f3zv7
  
  all lowercase letters
  
  first letter is a small suitcase E
  second is number Nine
  third letter is small case L
  fourth & fifth is number one
  Sixth letter is small box F
  seventh is number three
  eighth letter is small suitcase Z
  ninth letter is small case V
  the last is number seven
  
  Concerning
  
  Visruth

• message of undefined LabVIEW on custom codes error code

  "I use the VI General error handler to define custom errors, I have inserted all entries for this vi (user-defined descriptions, codes, user-defined error code, source of the error, type dialog and error in) but some I still get the message:"

  This error code is not set. Undefined errors can occur for several reasons. For example, no one has provided a description for the code, or you could have wired a number which is not an admission of error code error code.

  In addition, undefined error codes can occur because the error concerns a third object, such as the operating system or ActiveX. For these mistakes of third parties, you may be able to get a description of the error by searching on the Web for the error code (5501) or to its hexadecimal representation (0x0000157D). "

  Why? someone, anyone, help!... Thank you very much

  How you use the error handler General VI? Do you have examples of code?

  The following code displays the error dialog using my custom error description and the 'message' is also used my custom error description:

  

  The error is not changed - if I go to "explain the error", he then returned to the standard description for this error code (i.e. undefined). Using the Manager general error applies only the descriptions of the user to the call of the VI. You can always create a wrapper for the General error handler that has all your descriptions/error codes defined and then use it instead of the built-in one.

  To change the database from LabVIEWs internal error and/or include with a built application (one of the build specification options), you must use the custom error files.

• Error-229771 after compiling VI in the application builder

  Hello

  I went from LabVIEW 8.2.1 to LabVIEW 12.0f1. Installation is running on a computer clean windows 7, only the 12.0f1 of labview. My request for LabVIEW 8.2.1 works well within the development system. It seems to be 3 times slower than in LabVIEW 8.2.1, but is not the problem at the moment.

  After you create an application with the Builder asks LabVIEW 12.0f1, I get an error:

  Error-229771 to Start Task.vi DAQmx

  I know that several pages on the error 229771 on ni.com. None of the relay worked. The point, the vi runs within the system development, but not as an application, is noticeable.

  Anyone have an idea how to fix the prblem?

  Thank you very much and best regards,

  Michael

  
  

• I get a region code error when I try to play a new DVD

  I just bought a new DVD of the store, and I get a region code error message.  Laptop computer wants me to change the region code before I can read the DVD.

  Regardless of your operating system go to Device Manager, go to the CD/DVD drives, click the sign more or pointer, right click on the line that appears and click Properties, then go to the region of the DVD tab.

  Now, you have the choice to make, you will see changes remaining X, the value must be 4 if it has not been changed before, if you change you will need to change it back - 3-2, if you get to 0, you're stuck in this region!

  If the specified region is yours then I would take the rear DVD, if the region is other than your, you have the choice above then you must indicate other PC users.

• code error-808

  My VI is checked several conditions, when true, a Subvi expected popup and wait for my entry (press one of the four buttons), however this Subvi blocks (IE closed without waiting for my entry), so I checked the error out of this sub - VI and he said: code error-808, source: Timed structure (s): L110126428

  What does that mean?

  You can do either configuration GUI of the loop:

  

  or you can do it on the block schema by adding an entry to the entry node.

  

  Once again, it's all in the documentation.

• my computer turns off, no code error, no blue screen

  my computer restarts auto no code error, no blue screen, it might be the drivers that I have installed or?  What can I do to solve this problem or found out how to solve this problem

  Hello Shelly,

  Drivers could easily be the cause - or it could be quite a few other things.

  I recommend a restore of the system to a restore point before you did what you did (when it was working fine).  If you use Windows 7, seehttp://www.sevenforums.com/tutorials/700-system-restore.html. If you are using Vista, seehttp://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/. If you are using XP, seehttp://support.microsoft.com/kb/306084. Sometimes this simple process made the rounds and sometimes that doesn't help - but it is easy and worth if she has recently begun.

  Good luck!

  Kosh