code for a battery 9 cells

Similar Questions

• Compatible battery 9 cells for 15.4 "T61

  Can someone please provide a part number for a battery 9 cells compatible with the T61 6463 5BG 15.4 "?

  My 6-cell dies just out of warranty I searched the store from Lenovo and other sites, but I see conflicting information. Some batteries I've seen who are supposed to be compatible with my T61 clearly have a different form factor that does not. So I would really get a reference number that is really sure before buy you.

  Thanks in advance.

  Reference number: 40Y6797 is the battery 9 cells that can be used in the 15.4 inch T61 and R61 and many other Thinkpads.

• NB200 122 - what battery 6 cells is compatible?

  Just a question.

  I bought a NB200 122 because he had 3G and the processor was a little faster than others with 1.66 Ghz.
  The battery that comes with it is a 3 cell which lasts about 3 hours.
  I was envious of the battery 6 cells in the model 10J NB200, I think, which is supposed to last for 9 hours.

  These batteries are both compatible with my netbook, I want to say can I buy a 6 cell and use it without any problems or dangers?

  Thankss a lot in advance.

  Mohamed

  Hello

  I think you can use these battery 6 cells in the two booklets since the 10J NB200 and NB200 122 belong to the same series which is PLL25E.

  So I see no good reason for the battery 6 cells are not compatible with the NB200 122

  See you soon

• Can I get the battery 9-cell for Satellite Pro U400 - 13G?

  Hey

  Can someone tell me if it is possible to get a battery 9 cells for Satellite Pro U400 - 13G.
  And if it is then what is the part number?

  Best regards Anders

  You know the Web from Toshiba website Options & accessories?

  See this page:
  http://EU.computers.Toshiba-Europe.com-> peripheral services & -> PS Options & accessories

  There you will find all the compatible options.

  AFAIK this battery could be compatible with the Satellite Pro U400 series:
  * Battery Pack (Li-ion, 9 cell, 6000mAh) PA3537U-1BRS *.

  Good bye

• Compaq Presario CQ57-451xx: I need model or the manufacturer of the battery 6-cell for Compaq Presario laptop model # CQ57-451xx

  I use Compaq PresarioCQ57, model #CQ57-451xx laptop whose battery replacement is exhausted. I want to buy authentic original battery 6-cell HP or a replacement an as recommended by HP here or abroad for which I need adapted our part/model.

  HP spare parts numbers

  MU06 (6-cell)

  MU09 (9-cell)

  HP battery replacement table

  http://www.shopping.HP.com/shopping/PDF/HP_NB_Battery_Compatibility_Chart.PDF

• Is the KC991AA '/ tx1000 tx2000 laptop battery 8-cell' right for the TX2?

  Is the KC991AA '/ tx1000 tx2000 laptop battery 8-cell' right for the TX2? The descriptions on the website do not mention the TX2 at all even if accessories TX2 page is linked to the page for this battery.

  HP: can update you the web site?

  RQ204AA (6 cells) and KC991AA (8 cells) are compatible with the tx series... Yes, that's correct.

• Re: NB305 - replacement high capacity for original battery

  Hello

  I was wondering if someone could help.

  Can someone suggest a replacement for my original battery high capacity as it is mounted on my NB 305?

  I read blurb contradictory sale about 6 or 8 cell replacements and may not quite reach a definitive answer.

  Any help on the existence or the validity of replacement high capacity would be appreciated.

  TVM

  Hello

  Recommend that you check the NB305 PDF sheet
  http://cdgenp01.CSD.Toshiba.com/content/product/pdf_files/detailed_specs/toshiba_miniNB305-N310.PDF

  Here you will find compatible parts and the battery appears too.
  It seems that you can use the Toshiba primary high capacity Li Ion battery
  (6-cell), number of silver: PA3734U-1BRS

• Satellite A200 - what is the experience of the battery 9 cells?

  Hi im considering getting a battery 9 cells...

  Whats experince of peoples that they are much better?

  Where is a good place to go away and makes the quality varies a lot, or should I shop on price alone?

  How everyone takes care batterys there, you pull them out or off fee if it loads for long periods...

  Hello

  What Satellite notebook you have exactly?
  I m not an owner of the Satellite series but in my opinion with a 9cell battery you can more work on the mode of battery as with a battery 6 cells. So I think it also depends on the use of the laptop. I you use it often with AC/DC adapter I think that this upgrade is not so important.

  However, the Toshiba site, you can search for compatible batteries:
  http://EU.computers.Toshiba-Europe.com-online services & -online Options of PC Accessories devices & -Online Homepage Options & accessories PC

  And last but not least you can buy new batteries to an authorized service provider. On the Toshiba site you can also search for them ;)

  Welcome them

• Satellite A200 - HDD compatibility and more power with battery 9 cells

  I have a Satellite A 200 1 BJ with 4 GB of RAM, 300GB SATA HDD @4200 RPM (with 2 MB L2 Cache?) The warranty period is over. Is it possible to have an internal hard drive of 300 GB @7200 RPM with 8 MB of L2 Cache? Any idea on the cost?

  Also is it possible to get a battery 9 cells for my laptop?

  Hello

  I think that he should t be a problem to upgrade the 300 GB HARD disk. It should work.
  I put t know exactly how much it could be but still depends on the drive and the dealer making ;) simply google for certain offers.

  With regard to the issue of the battery;
  Well, you can check it out yourself. Toshiba Option & Accessories site offers options compatible notebook you;

  + http://eu.computers.toshiba-europe.com/-> peripheral services & -> Option & accessories +.

  Welcome them

• Need help with LabVIEW code for motor control.

  Hello

  My name is Sasi. I'm a grad student BME working on my thesis topic of assessment for back pain spine implants. To do this, I'm building a test machine that would apply pure moments of a specimen of the spinal column. I use LabVIEW 8.5 to implement the control of a brushless AC servo motor. My requirement is

  Step 1: Initialize the engine.
  Step 2: Start moving it to a uniform to the right PLAN (this value of RPM too user can enter).
  Step 3: while doing step 2; at the same time read the couple cell data (acquisition of data using Asst.). DAQ o/p is 0 v to 10 V; 0 v is 10 Nm n
  10 v is + 10 Nm
  Step 4: What torque reached + 10 Nm, i.e. 10 V, the engine stops.
  Step 5: from the position where the motor stopped (IE not need to return to the initial position) start moving in the opposite direction to the same
  Uniform rpm as in step 2 at the reading of data in the cells of the couple.
  Step 6: once more what torque reached-10 Nm, i.e. 0 V, the engine should stop.
  Step 7: Repeat "Step 2" to the "step 6' 3 times.
  Step 8: Reset engine position.

  So far, I managed to get the engine to move backward @ a desired vel, the accl, deceleration for 3 cycles before n n. I enclose my code. I have a problem inserting the code for reading DAQmx amidst all this. Can someone help me.

  Thnks,

  Sasi.

  Hi Sonia,.

  I took a quick glance to your problem and I think I have a solution for you.  I certainly agree with the suggestion of the use of parallel loops Lynn.  This will allow the portion DAQmx run uninhibited by the part of the motion, and vice versa.  In addition, you need only perform an iteration of the loop of the movement whenever the voltage level exceeds a threshold.  Thus, by performing an iteration on the code of movement in the same loop are you iterate over DAQmx code, you essentially waste processor.

  I created a VI that should do what you are wanting.  I tested it on me and it works very well.  You have a tweak a few things to apply to your system (such as motion Council DAQmx and physical channel ID, etc.).  I used two parallel loops and event programming.  Basically, the loop of movement starts the engine turns at the specified speed.  Once the engine is running, he expects the DAQmx loop to tell him that the voltage value has crossed the threshold.  When the voltage value exceeds the maximum threshold (I put a value slightly less than 10 to jitter and saturation), the DAQmx loop indicates the loop of the motion that it may end its iteration.  The motion loop stops the motion, causes a reversal and repeats the motion.  Once the movement has begun, he expects the DAQmx loop once again to tell him that a threshold was held, but this time, it's looking for a minimum threshold.  I used "Occurrences" to implement the event programming in LabVIEW.

  I've commented the code pretty thoroughly, so I hope that comments will answer all remaining questions.  The advantage of using programs that focus on the event for this is that you save time processor, and your movement is more closely synchronized with the DAQmx.  Instead of one iteration of the loop of movement as fast as you can, updates every hour, you just put in pause and wait for the other loop to tell you when to start up again.  Meanwhile, the processor doesn't have to worry about an iteration of this loop over and over again.  In addition, when the accident occurs, you catch him immediately, instead of having to wait until the next iteration.  Thus, you are more closely synchronized with the DAQmx code portion.

  I hope this will help you.  Please report if you have any questions about the code or its implementation.  Good luck!

  
  

• Pavilion dv6t-6100: battery 9-cell HP Pavilion dv6t-6100 dies prematurely

  I have a HP Pavilion dv6t-6100, I'm back (2011). When I set it up, I chose to get two batteries with it: the 6-cell battery that comes standard and the battery 9 cells optional. But I have a problem with the 9-cell: with it connected, the system always stops at 33% staying fresh with no warning, as warnings battery start to appear around 10-15% remaining fresh. I suspect that three of the 9 cells are quite dead. I checked on the website of accessories, but I couldn't find the same battery available and under 'Laptops from 2011 to 2013', the dv6t-6100 is not even mentioned. (The page has the Pavilion dv6t-7000 listed, but it's a different model entirely.) So I don't know where to find a new battery, which one to get, where to find the one that the label on my battery was told to replace it with, or anything of that kind. Can someone help me?

  My laptop runs Windows 10 Pro Insider overview since November 2014 after obtaining its hard drive replaced. The problem with the 9-cell occurred since before that date.

  Part number for battery 9 dv6t-6100:

  9-cell, 100 Wh, 3.00 - Ah Li - ion 636631-001

  New stock sold here:

  http://www.eBay.com/ITM/new-genuine-original-HP-laptop-battery-11-1V-93Wh-9-cell-MU09-636631-001-/171328160957?PT=LH_DefaultDomain_0&hash=item27e3f444bd

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Code product key? had reboot my computer and I need a code for Windows Vista from the bottom of my laptop

  Hi, I'm having a problem with my laptop. I bought my laptop online, a year ago, and I got a virus. Then, I had my computer reset and I need a code for Windows Vista from the bottom of my laptop. After looking through records and information, we found that he had no number. He worked initially but then recently he was asked for a product key or something of the sort code. I was using my laptop but I cannot customise my background etc.

  Can you help me?

  Thank you very much

  The code is located on a label and is a 25-digit alpha-numeric (and very hard to read) code separated into 5 groups of 5 numbers separated by dashes.  If you can't find it on the bottom of your laptop, open the battery housing and remove the battery and look there - I know of cases where this is where it was placed.

  If you can't find the product key, your only choice is to contact the manufacturer and see if they can help.  Sometimes the relocations made with recovery disks don't need to be activated (depends on the manufacturer and their recovery process must ask them and confirm before you spend money on the recovery discs).  A valid product key is required for activation if activation is required - there is no way around this problem.  And in case you are considering on it, you can't switch from one product not enabled - you need to do a clean and complete installation (update disc will not work).

  I hope this helps and that the manufacturer can help you.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• T500 battery 6 cells died after 287 Cycles?

  My battery of 6 cells in my T500 (bought in Nov 2008) is already dead. It holds a charge 14 Minute as of the present moment and holds less than 20% of its initial charge. Lenovo Power Manager says that he has only been cycled 287 times, however. I use the computer quite often, but I was under the impression that these are supposed to last 2-3 years?

  -What can I do to get a free spare battery from Lenovo or I'm on the hook for a new? I'm looking for in getting a battery 9 cells because the 6 cell never really gave me good life even at its peak.

  Ryan

  Hi manunited518!

  Lithium-ion batteries CAN last 300-500 cycles, but if they depend a lot on what happens during their lifetime. More informative description of the technology I know is The University of the battery. There is a nice article on How to prolong lithium-ion batteries. As it's there, 'a lithium-ion battery in use battery usually lasts between 2-3 years' but 'if used on food, inside a laptop battery won't last for 12 to 18 months. There are other factors that can shorten his life, too, like the heat.

  It is never wrong to ask about a replacement, but the basic battery warranty is 1 year, and you went that .

• All ThinkPad T410s come with a battery 6 cells coming out?

  I remember reading somewhere that the battery 6 cells exceeds on the side of the T410s makes clumsy in appearance and handling.  Is this always true?  If so, is there something like a 4 cells which remains flush with the chassis?  I couldn't find this as an option when you set up online, nor is he is listed as an accessory available for the T410s.

  s2kdriver80, I have a T400s, and six-cell battery is flush. Photographs that I saw, the T410s chassis is basically identical to the T400s, six-cell battery should also be built into the chassis. Cheers, RocketDude

• battery 9 cells X 220: Sanyo or LGC?

  Hi all! I tried to search past issues by comparing the battery 9 cells Sanyo and LGC, but were unsuccessful.

  In our office, I made the choice to get a new Sanyo 9 cells (Japan made, completed in China) or LGC (Korea, completed in China) battery.

  Which should I choose?

  Thanks in advance for your answers!

  My Sanyo x 9-cell 2 called leave them after 15 months, and my LGC going still strong after 3 years (although 70% of the original capacity after 220 cycles).