comments authorization access local network

Similar Questions

• AnyConnect client can not access local network

  Hello

  I have a problem with the Cisco anyconnect. Once clients are connected they cannot access anything whatsoever, including their default gateway.

  Pool of the VPN client is on the same subnet as the LAN (139.16.1.x/24). Local network clients can access DMZ, VPN clients can ping computers on the local network, but they cannot access the DMZ.

  I guess that any rule providing that traffic is absent but I m new with Cisco ASA and I m totally lost. I read as much as I could on this topic, but I do not understand which rule is necessary.

  Thank you very much in advance for your support.

  ASA release 9.4 (1)
  !
  ciscoasa hostname
  activate the encrypted password of WmlxhdtfAnw9XbcA
  TA.qizy4R//ChqQH encrypted passwd
  names of
  mask 139.16.1.50 - 139.16.1.80 255.255.255.0 IP local pool Pool_139
  !
  interface GigabitEthernet1/1
  nameif outside
  security-level 0
  192.168.1.100 IP address 255.255.255.0
  !
  interface GigabitEthernet1/2
  nameif inside
  security-level 100
  IP 139.16.1.1 255.255.255.0
  !
  interface GigabitEthernet1/3
  nameif DMZ
  security-level 50
  IP 172.16.1.1 255.255.255.0
  !
  interface GigabitEthernet1/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet1/5
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet1/6
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet1/7
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet1/8
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  Management1/1 interface
  management only
  nameif management
  security-level 100
  11.11.11.11 IP address 255.255.255.0
  !
  passive FTP mode
  network obj_any object
  subnet 0.0.0.0 0.0.0.0
  internal subnet object-
  139.16.1.0 subnet 255.255.255.0
  network dmz subnet object
  subnet 172.16.1.0 255.255.255.0
  wialon Server external ip network object
  Home 192.168.1.132
  wialon-Server network objects
  Home 172.16.1.69
  Wialon-service-TCP object service
  destination tcp source between 1 65535 21999 20100 service range
  Wialon-service-UDP object service
  destination service udp source between 0 65535 21999 20100 range
  network of the NETWORK_OBJ_139.16.1.0_25 object
  subnet 139.16.1.0 255.255.255.128
  outside_acl list extended access permit tcp any object wialon-Server eq www
  outside_acl list extended access allowed object Wialon-service-TCP any wialon-server object
  outside_acl list extended access allowed object Wialon-service-UDP any wialon-server object
  pager lines 24
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  MTU 1500 DMZ
  management of MTU 1500
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) static source any any static destination NETWORK_OBJ_139.16.1.0_25 NETWORK_OBJ_139.16.1.0_25 non-proxy-arp-search to itinerary
  !
  network obj_any object
  dynamic NAT (all, outside) interface
  internal subnet object-
  NAT dynamic interface (indoor, outdoor)
  wialon-Server network objects
  NAT (DMZ, external) service wialon Server external ip static tcp www www
  Access-group outside_acl in interface outside
  Route outside 0.0.0.0 0.0.0.0 192.168.1.1 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  identity of the user by default-domain LOCAL
  Enable http server
  http 11.11.11.0 255.255.255.0 management
  http 139.16.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  service sw-reset button
  Crypto ipsec ikev2 AES256 ipsec-proposal
  Protocol esp encryption aes-256
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES192
  Protocol esp encryption aes-192
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES
  Esp aes encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 proposal ipsec 3DES
  Esp 3des encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal OF
  encryption protocol esp
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec pmtu aging infinite - the security association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  Crypto ca trustpoint ASDM_TrustPoint0
  registration auto
  domain name full ciscoasa.srdongato.null
  E-mail [email protected] / * /
  name of the object CN = srdongato
  Serial number
  Proxy-loc-transmitter
  Configure CRL
  Crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
  registration auto
  full domain name no
  name of the object CN = 139.16.1.1, CN = ciscoasa
  ASDM_LAUNCHER key pair
  Configure CRL
  trustpool crypto ca policy
  string encryption ca ASDM_TrustPoint0 certificates
  certificate 09836256
  30820381 30820269 a0030201 02020409 83625630 0d06092a 864886f7 0d 010105
  05003050 31123010 06035504 03130973 72646f6e 6761746f 313 has 3012 06035504
  05130b4a a 41443139 32323033 34343024 06092, 86 01090216 17636973 4886f70d
  636f6173 612e7372 646f6e67 61746f2e 6e756c6c 31353132 30353036 301e170d
  5a170d32 33333535 35313230 32303633 3335355a 30503112 30100603 55040313
  09737264 6f6e6761 30120603 55040513 31393232 30333434 0b4a4144 746f313a
  2a 864886 30240609 f70d0109 6973636f 02161763 6173612e 7372646f 6e676174
  6f2e6e75 6c6c3082 0122300d 06092 has 86 01010105 00038201 0f003082 4886f70d
  010a 0282 010100d 2 295e679c 153e8b6a d3f6131d 8ea646e3 aa0a5fa9 20e49259
  ca895563 7e818047 033a4e8f 57f619e9 fa93bfd5 6c44141f b0abf2c0 8b86334e
  bac63f41 99e6d676 c689dcf7 080f2715 038a8e1b 694a00de 7124565e a1948f09
  8dbeffab c7c8a028 741c5b10 d0ede5e9 599f38fe 5b88f678 4decdc4b b 353, 6708
  cfa2fbce f58be06e 18feba56 4b2b04a1 77773ec6 5c58d2ed d7ca4f17 980f0353
  138bfe65 1b1165e6 7b6f94bb ab4d4286 e900178c 147a6dba 2427f38e e225030f
  0a66d1eb 5075c57e 6d77e5bb 247f5bc3 8d3530f0 49dedf2d 21a24b5f daa08d98
  690183cf e82a6b8d 5e489956 c5eecdbc 7fc2365c b629a52b 126b51e2 18590ed5
  c9da8503 a639f102 03010001 a3633061 300f0603 551d 1301 01ff0405 30030101
  ff300e06 03551d0f 0101ff04 86301f06 04030201 23 04183016 80143468 03551d
  dec79103 0a91b530 1ada7e47 7e27b16d 4186301d 0603551d 0e041604 143468de
  c791030a 91b5301a da7e477e 27b16d41 86300d 86f70d01 01050500 06 092 a 8648
  003cdb04 03820101 8ef5ed31 c05c684b ad2b0062 96bfd39a ecb0a3fe 547aebe5
  14b753e7 89f55827 3d4e0aa8 b8674e45 80d4c023 8e99a7b4 0907d 347 060a2fe4
  fa6e0c2f 3b9cd708 a539c09f 7022d2ee fb6e2cf6 82b0e861 a2839a71 1512b3ec
  e28664e9 732270c 9 d1c679d9 1eaf2ad5 31c3ff97 09aae869 88677a3d b 007, 5699
  ecb3032e 2dd0f74f 81f9a8fb 79f30809 723bbdbf dfef4154 5ad6b012 a8f37093
  481fa678 b44b0290 23390036 042828f3 5eefdc43 ebe52d26 78934455 9b4234a9
  4146 166e5adc b431f12f 8d0fbf16 46306228 731c bfeebc43 34 76984 d2e6ebbc
  88ca120a 96838694 d4f32884 963e7385 987ec6b0 dfa28d49 05ba5fa8 641bcfc7
  ff92ac3c 52
  quit smoking
  string encryption ca ASDM_Launcher_Access_TrustPoint_0 certificates
  Certificate 0 is 836256
  308202cc a0030201 0202040a 0d06092a 83625630 864886f7 0d 010105 308201b 4
  05003028 06035504 03130863 61736131 13301106 03550403 6973636f 3111300f
  130a 3133 392e3136 2e312e31 31353132 30353036 35363236 5a170d32 301e170d
  35313230 32303635 3632365a 30283111 55040313 08636973 636f6173 300f0603
  61311330 11060355 0403130 3133392e 31362e31 2e313082 0122300d 06092 has 86
  4886f70d 01010105 00038201 0f003082 010 has 0282 010100e7 a5c16e86 16c15a10
  e018b868 bac7271a 30f1a3f8 ecb9c6b8 3ed4b1ad c9468f5e 287f2a7a 644f1496
  c43a061e da927d09 a755b53e ed7c6a66 f2f1fb1e f944345c 86e08ce0 891c99b3
  13101ab3 04963fad f91f987f 99f22a89 cd1e8c5a 5e4c026d 2cadd7b7 6620bbd1
  b4a5135b 24ec886f fa061a06 dd536e96 1e483730 756c 4101 23f83a8d 944a7fbe
  93c51d56 32ac0d17 ceb75f63 0ae24f07 f2c54e83 5b84ff00 16b0b899 c925c737
  1765b 066 23 b 54645 bc419684 d09dd130 c1479949 68b0a779 df39b078 6fb0deb9
  758b14c3 f0801faf f0ad60e1 a018ffba d769f867 3fe8e5fc 88ccc5b2 2319f5d4
  617a78c4 74e7a64b 5c68276c 06ea57c1 d0ffce4b 358c4d02 03010001 300 d 0609
  2a 864886 05050003 82010100 dff97c9f 4256fd47 8eb661fd d22ecea4 f70d0101
  589eff09 958e01f1 a435a20e 5ed1cf19 af42e54d d61fc0ab cb2ee7ac 7fcb4513
  1a44cc86 1e020d72 3a3f78d2 4 d 225177 857093d 9 f5fcf3c7 6e656d2b 54a0c522
  f636b8cf 33c5ae34 ea340f32 85dff4c1 50165e7a e94de10b ced15752 0b3a76c1
  2a50777b 20291106 a1a8a214 a 8 003716 680c15d4 ac3f7cc7 378f8f5f 38e3403f
  f958c095 e549c8ed 4baf8cc5 bdcd230e 260754ea 953c3a4c eb01fef5 62b97e01
  9f82ce6b f479dbdd 000c45af 8758b35f b4a958ee 32c4db3f 2ddc7385 dc05b0e3
  78b609ba a9280841 2433ae87 5dd7a7c2 d5691068 1dc0eddc c23f99c5 3df8b1a5
  aadbd82a 423f4ba8 563142bf 742771c 3
  quit smoking
  IKEv2 crypto policy 1
  aes-256 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 10
  aes-192 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 20
  aes encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 30
  3des encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 40
  the Encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  Crypto ikev2 activate out of service the customer port 443
  Crypto ikev2 access remote trustpoint ASDM_TrustPoint0
  Telnet 139.16.1.0 255.255.255.0 inside
  Telnet 11.11.11.0 255.255.255.0 management
  Telnet timeout 5
  without ssh stricthostkeycheck
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  dhcpd outside auto_config
  !
  dhcpd address 172.16.1.69 - DMZ 172.16.1.69
  dhcpd dns 87.216.1.65 87.216.1.66 DMZ interface
  dhcpd option 3 ip 172.16.1.1 DMZ interface
  dhcpd enable DMZ
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  SSL-trust outside ASDM_TrustPoint0 point
  SSL-trust ASDM_Launcher_Access_TrustPoint_0 inside point
  Trust ASDM_Launcher_Access_TrustPoint_0 inside the vpnlb-ip SSL-point
  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-win-3.1.12020-k9.pkg 1
  AnyConnect profiles Wialon_client_profile disk0: / Wialon_client_profile.xml
  AnyConnect enable
  tunnel-group-list activate
  Disable error recovery
  internal GroupPolicy_Wialon group strategy
  attributes of Group Policy GroupPolicy_Wialon
  WINS server no
  value of 192.168.1.1 DNS server
  client ssl-VPN-tunnel-Protocol ikev2
  by default no
  WebVPN
  AnyConnect value Wialon_client_profile type user profiles
  dynamic-access-policy-registration DfltAccessPolicy
  wialon_1 Wy2aFpAQTXQavfJD username encrypted password
  wialon_2 4STJ9bvyWxOTxIyH encrypted password username
  remote access to Wialon tunnel-group type
  attributes global-tunnel-group Wialon
  address pool Pool_139
  Group Policy - by default-GroupPolicy_Wialon
  tunnel-group Wialon webvpn-attributes
  enable Wialon group-alias
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:447ec315ae30818a98f705fb1bf3fd75

  Hello

  You don't have NAT exemption the DMZ network to the pool of VPN traffic.

  Please try to add the following statement to run:

  nat (DMZ,outside) 1  source static any any destination static NETWORK_OBJ_139.16.1.0_25 NETWORK_OBJ_139.16.1.0_25 route-lookup

  Also please delete the existing instruction manual nat "non-proxy-arp" statement, because it can cause problems like you the ip subnet address pool is identical to that of the Interior of the network.

  no nat (inside,outside) source static any any destination static NETWORK_OBJ_139.16.1.0_25 NETWORK_OBJ_139.16.1.0_25 no-proxy-arp route-lookup
  
  nat (inside,outside) 1 source static any any destination static NETWORK_OBJ_139.16.1.0_25 NETWORK_OBJ_139.16.1.0_25 route-lookup
  
  

  Cordially Véronique

• I can only access local network with WPA/WPA2-PSK compatible. With out security I can connect without any problems.

  Issue of WPA/WPA2-PSK on Vista with SP2

  Belkin F7D2301 router, version1

  Vista Home Premium, Service Pack 2

  Network card: Atheros AR5007 802. 11a / g WiFi. version of the driver. 7.3.201.25.

  I am running 2-1 Vista, 1 Window7 laptop
  IPhone 2
  1 Wii game system

  When I installed initially the new router today, I installed it with WPA - PSK [TKIP] + security WPA2-PSK [AES] option. When in doing so, the Vista Home Premium (32 bit) would not connect to the internet. He would show local only access.

  But when I disable security it can connect to the internet. Rest of my devices are also able to connect to the internet regardless of WPA - PSK [TKIP] + WPA2-PSK [AES] or security number. I am running Vista with SP2.  That seems known problem Vista on Sp1. see http://support.microsoft.com/kb/935222.

  The network adapter I have is an Atheros AR5007 802. 11a / g WiFi with the version of the driver. 7.3.201.25.

  Any help would be very happy... I'm exhausted now try to solve this problem.

  SOLVED by updating the driver for Atheros. Atheros AR5007 802. 11a / g WiFi. It is not available on the official website. Check out this forum.

  http://forums.techguy.org/networking/981134-solved-NETGEAR-WNDR3700-incompatibilty-w.html

  Mysteryis yet to be sloverd

  • Why stop WPA has collaborated with the old version of Atheros AR5007 802. 11a / g WiFi. version of the driver. 7.3.201.25.
  • Why accpeting Linksys WRNT160 V3 ceased any connection.

  Thanks for the support

• Unable to access local network error message says I must enableiov6

  Original title: network

  Troubleshooting of network cannotaccess localnetwork said I need to enableiov6i need help

  Hello

  1. What is the exact error code or message?

  2. have you made any recent hardware or software made to your calculation before the show?

  3. using a wired or wireless?

  Please follow the links below and check the issue:

  Wi - Fi and in Windows network connection issues:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

   
   
  See the link on how to disable IP V6 below:
   
  How to disable specific components or IP version 6 in Windows
  http://support.Microsoft.com/kb/929852
   

  Warning: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

   
   
  I hope this helps.

• Hi guys. on the macbook in System Preferences > sharing there is a box at the top that says "computers on your local network can access your computer at:" means that other people can access my computer?

  Hi guys. on the macbook in system preferences > sharing there is a box at the top that says "computers on your local network can access your computer at:" means that other people can access my computer?

  "Your local network" is the computers that are on the same router as you. At home, this is your family.

  to: "computer name" is the name of the computer, they will see.

  Access is provided for items you decide to activate, usually file sharing. For sharing of files, ONLY the items that you specify in the file sharing dialog box details panel is accessible and be only users you EXPLICITLY list by username.

• Access to distance running OS x server local network

  I have a 2 person office with a local ethernet network connected to the internet via wifi provided by office building. Is there an easy way to connect to my server from Home Office? I have osx server updated to el capitan running on a mac mini. My colleague is connected using GoToMyPC, but I want to put in place so that I don't have the extra cost of this service if I can.

  To run a public VPN server behind a NAT gateway, you must do the following:

  1 give the bridge either a static external address or a dynamic DNS name. It must be a DNS record a public DNS record, not on the server itself. Also, in the latter case, you must run a background process to keep the DNS record update when your IP address changes.

  2. give the VPN server a static address on the local network and a host name that is not in the 'local' top-level domain (which is reserved for the Hello).

  3 transmit external ports 500 and 4500 1701 (for L2TP) UDP and TCP 1723 (for PPTP) port to the corresponding ports on the VPN server. The app Server can set this up for you if you have a router from Apple.

  If your router is an Apple device, select the AirPort network utility and click Network Options. In the leaf opens, check the box marked

  Allow inbound IPSec authentication

  If this isn't already done and save the change.

  There may be a similar setting on a third-party router.

  4. configure the firewall in use to pass this traffic.

  5. in the sidebar of the application server, select the server name, then select the Access tab. Access to the network for VPN service must be all the networks, if you want customers to be able to connect from anywhere.

  If you have followed all the steps above, the server application must show that the VPN service is accessible from the Internet to the external IP address. Otherwise, something in the network is blocking some of the required traffic. Some residential ISPS block incoming UDP packets redirected. If yours is by doing this, you will not be able to set up a virtual private network.

  6. each client must have an address on a network block that don't overlap one assigned by the VPN endpoint. For example, if endpoint affects addresses in the 10.0.0.0/24 range, and that the client has an address on a local network in the range of 10.0.1.0/24, it's OK, but if the LAN is 10.0.1.0/16, there will be a conflict. To reduce the risk of conflicts of this kind, it is preferable to address assignment to a random subblock of 10.0.0.0./0 with a mask of 24 bits.

  7. "back to my Mac" is incompatible with the VPN service. It should be disabled on the server and on an AirPort base station, if necessary.

  8 Hello won't work on an L2TP or PPTP VPN. To make services accessible through the tunnel, you need a DNS service work.

  If necessary, services such as mail must be configured to listen on the block assigned to the VPN clients network.

  9. If the server is connected directly to the Internet rather than being behind a NAT, see this blog.

• No Internet access, the 'Connect to the Local network' and 'Wireless network connection' are "Local only".

  I'm portable computer maintenance of the customer, a Toshiba Satellite L305-S5885, under Vista Home Premium x 86 SP2, with infections by malicious software and internet connection problems. I have managed to get rid of all of its 251 infections and I am now addressing the connectivity problem. I'm unable to achieve on its ethernet or a wireless connection to Internet. The two network status of connections 'Unidentified network', and also ' access: Local only ' all other machines hooked up to my router via CAT5e and some via 802.11 g/n, have excellent speeds with internet connectivity, so I know that the problem is limited to his machine. I tried the following:

  Deactivation and reactivation of these two connections: FAIL.

  "Diagnose and repair" on the two connections: FAIL.

  Under dynamic I.P. type to static/static to the dynamic: FAIL.

  Uninstalled all network via Device Manager devices, then restart: FAIL.

  Manually uninstalled all the drivers and utility and installed the latest versions: FAIL

  The command ipconfig/all text follows:

  ----------------------------------------------
  Microsoft Windows [Version 6.0.6002]
  Copyright (c) 2006 Microsoft Corporation. All rights reserved.

  C:\Users\Brooklyn's>ipconfig/all

  Windows IP configuration

  Name of the host...: Brooklyns-PC
  Primary Dns suffix...:
  Node... type: broadcast
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Intel (r) Wireless WiFi Link 4965AGN
  Physical address.... : 00-21-5C-31-87-95
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Autoconfiguration IPv4 address. . : 169.254.174.235 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
  Description...: Realtek RTL8102E Family PCI - E Fast Ethern
  and NIC (NDIS 6.0)
  Physical address.... : 00-1E-33-4E-2E-F7
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Autoconfiguration IPv4 address. . : 169.254.74.29 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  NetBIOS over TCP/IP...: enabled

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {C41651CC-0B3D-411D-8187-745214 C 69}
  B4B}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {816357D 3-D 8-494C-AA09-F622AE861 44}
  0FA}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 14:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  C:\Users\Brooklyn's >
  --------------------------------------------------

  Guys, I'm really hitting my head against the wall on this one, and I would be VERY happy for any help through this. Thank you!

  I thought about it, there was a corrupted installation of Norton 360, the origin of the problem. I've used the Norton removal tool and voila! Internet! Thank you.

• I can connect to my network, but with access "local only".

  Access to the "Local" network only
  I can connect to my network, but with access "local only".  Internet became more intermittent (not sure if that is related or if I guess it) and did not work in several weeks.  Desktop computer is plugged into the router, but have the same problem when it is plugged into the DSL modem.  Other computers on the same router (wireless or other) work very well.  Recently, I removed Mcaffee and installed MS security essentials.  I uninstalled mcaffee of programs and settings then used the mcaffee removal tool to lighten the rest.  I uninstalled and reinstalled MS security essentials.  I thought it might be a firewall issue, but I get error 0x6D9 when I try to start it.  I tried all the steps in the following post, nothing helps.  Any other suggestions?

  ______________________

  You can follow the steps below and check if that helps you solve the problem.

  Method 1

  Try to power cycle the router and the computer and check if it helps.

  On the PC:

  1. Save your work and restart the machine.

  On the router or modem (if wireless printing):

  1. Unplug the router and the modem.
  2. Wait 30 seconds.
  3. Plug in the modem and wait for it to come to the ready state.
  4. Plug in the router.

  After you put cycle check the connection between the router and the computer.

  Method 2

  If the steps above do not help, you mayreset TCP/IP stack. To reset access the link below and either click on "Fix it for me" or follow the instructions to fix it yourself:http://support.microsoft.com/kb/299357
   
  Disable the IP helpdesk:
  1 hold the Windows key and type R, type "services.msc" (without the quotes) and press enter
  2. scroll down to the IP assistance service, right-click on it and select Properties
  3. in the drop-down list box that says "Automatic" or "Manual", set it to disabled and then click 'apply '.
  4. then click on "Stop" to stop the service from running in the current session
  5. click on OK to exit the dialog box

  Method 3

  Disable IPv6 and remove IPv6 virtual cards:
   
  Try to uninstall IPv6 on all interfaces, the removal of virtual cards of IPv6 and reset the TCP/IP stack. To remove the IPv6, go to the properties for each network adapter, and deselect the check box next to the Protocol "Internet Protocol version 6 (TCP/IPv6), which will turn off, or select it and click on uninstall, which withdraw power off the computer.» Then go into Device Manager and remove any 4to6 adapters, adapters miniport WUN or tunnel adapters.
  NOTE: You should do this for each network connection, even if they are disabled.

  Method 4

  Disable the DHCP Broadcast Flag:
  Link: http://support.microsoft.com/default.aspx/kb/928233
  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://support.microsoft.com/kb/322756.  How to back up and restore the registry in Windows
   
  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
   
  To resolve this issue, disable the DHCP BROADCAST flag in Windows Vista. To do this, follow these steps:

  
  1. Click Start, type regedit in the search box, and then click regedit in the list programs.
  2. If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
  3. Locate and then click the following registry subkey:
  4 HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\ {GUID}
  5. in this registry path, click the (GUID) subkey that corresponds to the network adapter that is connected to the network.
  6. on the Edit menu, point to new, and then click DWORD (32-bit) value.
  7. in the new area #1, type DhcpConnEnableBcastFlagToggle and press ENTER.
  8. right click on DhcpConnEnableBcastFlagToggle, then click on modify.
  9. in the value data box, type 1 and then click OK.
  10. close the registry editor.
   
  By setting this registry key to 1, Windows Vista's trying to get an IP address using the BROADCAST flag in DHCP Discover packets. If that fails, he will try to obtain an IP address without using the BROADCAST flag in DHCP Discover packets.
  You can also try uninstalling and reinstalling the driver for the wireless card.

  ________________

  Thanks for any help!

  Hello

  All changes to the software or hardware of the computer?

  Method 1:

  Visit the link below and follow the steps.

  Of network connectivity status incorrectly as 'Local' only on a Windows Server 2008 or Windows Vista-based computer that has multiple network cards

  http://support.Microsoft.com/kb/947041

  Method 2:

  Update the NIC drivers and check.

  Network adapter problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

• Cannot view or access my local network of 'my network places '.

  Since the evolution of my router to router ZyWEL I can't diplay or access other computers on my local network. The entire network is invisible from all computers.

  Mallorcan salvation,

  Are a. When you facing this problem?

  B. you get errors?

  C. do you have a cable or a wireless network connection?

  D. the router is not compatible with vista?

  Have e. you checked if a firewall blocks the router?

  First check to see if a firewall is blocking the router then try the procedure below.

  Open Network Diagnostics by right-clicking the network icon in the notification area, and then click diagnose and repair.

  Make sure that all cables are connected (for example, make sure that your modem is connected to a working jack or cable phone connection, either directly or through a router).

  If you try to connect to another computer, make sure that this computer is turned on and that you have enabled file and printer sharing on your network. For more information, see networking of computers running different Windows versions.

  If your computer has a wireless network adapter, Windows automatically detects wireless networks that are located nearby. To see a list of wireless networks that Windows has detected, click the Start button and then click on connection to. If Windows does not detect a network that you think is in range of your computer, open help and Support and search for "Solving problems finding wireless networks."

  Try not the articles below.

  The problems of finding computers on a home network
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-computers-on-a-home-network

  Solve problems with computers not appearing is not in the network map
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-computers-not-appearing-on-the-network-map

  Network connection problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  I hope this helps.

  Bindu S - Microsoft Support

  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• The field for local network IPs access permissions

  Is an error or a restriction of the service if I have added ' * ' to avoid restrictions on access area on my app it works only on public IP addresses and is not with local network IPs?

  (ie. my phone WiFi 192.16.1.116 and trying to access information on a pc with 192.16.1.119, result: timeout)

  If the same request is made to a public IP (pc) IE. 200.31.90.37, then it works as expected.

  NOTE:

  -This request for access is made by a webworks installed on the phone app. the answer is in JSONP format.

  -PC firewall disabled.

  Tests failed

  -Tests on wifi, access to a local IP network with the phone on and off data service

  Successful trial

  -Tests on Internet, access a public IP, same phone, same app.

  As indicated in the following link, there is no indication that this behavior is expected:

  http://docs.BlackBerry.com/en/developers/deliverables/27280/Allowing_access_to_external_resources_an...

  If anyone knows an example where "*" works for LAN IPs please let me know.

  Kind regards

  OK... sit tight for this possible explanation

  A BlackBerry has two different designs to consider:

  (1) physical network connection

  (2) selection of transport

  The physical network connection is pretty self explainatory (wifi, bluetooth, GPRS, CDMA).  The selection of Transport can better be seen as a VPN Tunnel/connection.  Such transport may be BES, BIS, direct TCP, WAP etc gateway.

  Even if you're on WiFi, you can still have your transport (VPN) connected through BIS.  This is configured through your application settings.

  The browser from on the BB6 uses special transportation (no available applications) who did essentially the equivalent of a DNS lookup and follows a logic to see how endpoint can be accessed.  It will then forward through the transport that's going to happen to its endpoint.

  So in the browser, it detects your IP address isn't public and a rebooking via the TCP/IP connection direct to go directly to your local server.

  In a BlackBerry application, you must declare your list of transport order which I will try and failover to the other if it is not reachable on the first transport.

  Stopped default transport is in an application of WebWorks BES, BIS - B, TCP_WIFI, TCP_CELLULAR, WAP2, WAP

  More information on transport in WebWorks here:

  http://docs.BlackBerry.com/en/developers/deliverables/27261/Widget_element_834671_11.jsp#RIM_connect...

  In your case, you would have to change the order of the TCP_WIFI put everything first.  WARNING: Different transport have different failover times.  B BIS and BES are instantly switched if they are not enabled with this service. TCP_WIFI will actually make a connection delay before switching.  So if you don't have a WiFi connection, it will timeout on each request for a resource before it tries then BIS - B.

  So, it boils down to what you want your app to be able to do.  If she wants to access the public IP addresses, then you want to keep the default transport order.  If you want it to be able to discover the local and public IP addresses, then you will have a little more work to do.

• ASA5505 can transfer clients to remote VPN access to the local network

  I have currently ASA 5505 and 2911-router and I am trying to configure the VPN topology.

  Can ASA5505 you transmit to remote VPN access clients LAN operated by another router?

  These two cases are possible? :

  (1) ASA 5505 and 2911-router are separate WAN interfaces, each connected directly to the ISP. But so can I connect an other interfaces LAN of ASA 5505 in a switch managed by 2911 router customers to distance-SSL-VPN to inject into the local network managed by the router?
  (2) ASA 5505 is behind router-2911. May 2911 router address public ip or public ip address VPN-access attempts have directly be sent to ASA 5505 when there is only a single public ip address address available?
  Long put short, ASA 5505 can inject its clients to remote-access-VPN as one of the hosts on the local network managed by 2911-router?
  Thank you.

  I could help you more if you can explain the purpose of this configuration and connectivity between the router and ASA.

  You can activate the reverse route on the dynamic plane on the SAA. The ASA will install a static route to the customer on the routing table. You can use a routing protocol to redistribute static routes to your switch on the side of LAN of the SAA.

• remote VPN and vpn site to site vpn remote users unable to access the local network

  As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config

  The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.

  ASA Version 8.2 (2)
  !
  host name
  domain kunchevrolet
  activate r8xwsBuKsSP7kABz encrypted password
  r8xwsBuKsSP7kABz encrypted passwd
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  PPPoE client vpdn group dataone
  IP address pppoe
  !
  interface Ethernet0/1
  nameif inside
  security-level 50
  IP 192.168.215.2 255.255.255.0
  !
  interface Ethernet0/2
  nameif Internet
  security-level 0
  IP address dhcp setroute
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  management only
  !
  passive FTP mode
  clock timezone IST 5 30
  DNS server-group DefaultDNS
  domain kunchevrolet
  permit same-security-traffic intra-interface
  object-group network GM-DC-VPN-Gateway
  object-group, net-LAN
  access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
  tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  MTU 1500 Internet
  IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
  ICMP unreachable rate-limit 1 burst-size 1
  enable ASDM history
  ARP timeout 14400
  NAT-control
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console
  AAA authentication enable LOCAL console
  LOCAL AAA authentication serial console
  Enable http server
  x.x.x.x 255.255.255.252 out http
  http 192.168.215.0 255.255.255.252 inside
  http 192.168.215.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto-map dynamic dynmap 65500 transform-set RIGHT
  card crypto 10 VPN ipsec-isakmp dynamic dynmap
  card crypto VPN outside interface
  card crypto 10 ASA-01 set peer 221.135.138.130
  card crypto 10 ASA - 01 the transform-set RIGHT value
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 65535
  preshared authentication
  the Encryption
  sha hash
  Group 2
  lifetime 28800
  Telnet 192.168.215.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 5
  Console timeout 0
  management-access inside
  VPDN group dataone request dialout pppoe
  VPDN group dataone localname bb4027654187_scdrid
  VPDN group dataone ppp authentication chap
  VPDN username bb4027654187_scdrid password * local store
  interface for identifying DHCP-client Internet customer
  dhcpd dns 218.248.255.141 218.248.245.1
  !
  dhcpd address 192.168.215.11 - 192.168.215.254 inside
  dhcpd allow inside
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  Des-sha1 encryption SSL
  WebVPN
  allow outside
  tunnel-group-list activate
  internal kun group policy
  kun group policy attributes
  VPN - connections 8
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value split tunnel
  kunchevrolet value by default-field
  test P4ttSyrm33SV8TYp encrypted password username
  username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
  username kunauto attributes
  Strategy Group-VPN-kun
  Protocol-tunnel-VPN IPSec
  tunnel-group vpngroup type remote access
  tunnel-group vpngroup General attributes
  address pool VPN_Users
  Group Policy - by default-kun
  tunnel-group vpngroup webvpn-attributes
  the vpngroup group alias activation
  vpngroup group tunnel ipsec-attributes
  pre-shared key *.
  type tunnel-group test remote access
  tunnel-group x.x.x.x type ipsec-l2l
  tunnel-group ipsec-attributes x.x.x.x
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  Review the ip options
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
  : end
  kunauto #.

  Hello

  Looking at the configuration, there is an access list this nat exemption: -.

  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0

  But it is not applied in the States of nat.

  Send the following command to the nat exemption to apply: -.

  NAT (inside) 0 access-list sheep

  Kind regards

  Dinesh Moudgil

  P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community

• Client remote access VPN gets connected without access to the local network

  : Saved

  :

  ASA 1.0000 Version 2

  !

  hostname COL-ASA-01

  domain dr.test.net

  turn on i/RAo1iZPOnp/BK7 encrypted password

  i/RAo1iZPOnp/BK7 encrypted passwd

  names of

  !

  interface GigabitEthernet0/0

  nameif outside

  security-level 0

  IP 172.32.0.11 255.255.255.0

  !

  interface GigabitEthernet0/1

  nameif inside

  security-level 100

  IP 192.9.200.126 255.255.255.0

  !

  interface GigabitEthernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/4

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/5

  nameif failover

  security-level 0

  192.168.168.1 IP address 255.255.255.0 watch 192.168.168.2

  !

  interface Management0/0

  nameif management

  security-level 0

  192.168.2.11 IP address 255.255.255.0

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain dr.test.net

  network of the RAVPN object

  192.168.0.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.168.200.0_24 object

  192.168.200.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.9.200.0_24 object

  192.9.200.0 subnet 255.255.255.0

  the inside_network object-group network

  object-network 192.9.200.0 255.255.255.0

  external network object-group

  host of the object-Network 172.32.0.25

  Standard access list RAVPN_splitTunnelAcl allow 192.9.200.0 255.255.255.0

  access-list extended test123 permit ip host 192.168.200.1 192.9.200.190

  access-list extended test123 permit ip host 192.9.200.190 192.168.200.1

  access-list extended test123 allowed ip object NETWORK_OBJ_192.168.200.0_24 192.9.200.0 255.255.255.0

  192.9.200.0 IP Access-list extended test123 255.255.255.0 allow object NETWORK_OBJ_192.9.200.0_24

  pager lines 24

  management of MTU 1500

  Outside 1500 MTU

  Within 1500 MTU

  failover of MTU 1500

  local pool RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 IP mask

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 66114.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) source Dynamics one interface

  NAT (it is, inside) static static source NETWORK_OBJ_192.9.200.0_24 destination NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.9.200.0_24

  Route outside 0.0.0.0 0.0.0.0 172.32.0.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  Enable http server

  http 0.0.0.0 0.0.0.0 outdoors

  http 0.0.0.0 0.0.0.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  Terminal registration

  name of the object CN = KWI-COL-ASA - 01.dr.test .net, C = US, O = KWI

  Configure CRL

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  authentication crack

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 20

  authentication rsa - sig

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 40

  authentication crack

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 50

  authentication rsa - sig

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  authentication crack

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 80

  authentication rsa - sig

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 100

  authentication crack

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 110

  authentication rsa - sig

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 120

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 130

  authentication crack

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 140

  authentication rsa - sig

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 150

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet 192.9.200.0 255.255.255.0 inside

  Telnet timeout 30

  SSH 0.0.0.0 0.0.0.0 management

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH 66.35.45.128 255.255.255.192 outside

  SSH 0.0.0.0 0.0.0.0 inside

  SSH timeout 30

  SSH version 2

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow outside

  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

  AnyConnect enable

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  internal RAVPN group policy

  RAVPN group policy attributes

  value of server WINS 192.9.200.164

  value of 66.35.46.84 DNS server 66.35.47.12

  VPN-filter value test123

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value test123

  Dr.kligerweiss.NET value by default-field

  username test encrypted password xxxxxxx

  username admin password encrypted aaaaaaaaaaaa privilege 15

  vpntest Delahaye of encrypted password username

  type tunnel-group RAVPN remote access

  attributes global-tunnel-group RAVPN

  address RAVPN pool

  Group Policy - by default-RAVPN

  IPSec-attributes tunnel-group RAVPN

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory 2

  Subscribe to alert-group configuration periodic monthly 2

  daily periodic subscribe to alert-group telemetry

  aes encryption password

  Cryptochecksum:b001e526a239af2c73fa56f3ca7667ea

  : end

  COL-ASA-01 #.

  Here is a shot made inside interface which can help as well, I've tried pointing the front door inside the interface on the target device, but I think it was a switch without ip route available on this subject I think which is always send package back to Cisco within the interface

  Test of Cape COLLAR-ASA-01 # sho | in 192.168.200

  25: 23:45:55.570618 192.168.200.1 > 192.9.200.190: icmp: echo request

  29: 23:45:56.582794 192.168.200.1.137 > 192.9.200.164.137: udp 68

  38: 23:45:58.081050 192.168.200.1.137 > 192.9.200.164.137: udp 68

  56: 23:45:59.583176 192.168.200.1.137 > 192.9.200.164.137: udp 68

  69: 23:46:00.573517 192.168.200.1 > 192.9.200.190: icmp: echo request

  98: 23:46:05.578110 192.168.200.1 > 192.9.200.190: icmp: echo request

  99: 23:46:05.590057 192.168.200.1.137 > 192.9.200.164.137: udp 68

  108: 23:46:07.092310 192.168.200.1.137 > 192.9.200.164.137: udp 68

  115: 23:46:08.592468 192.168.200.1.137 > 192.9.200.164.137: udp 68

  116: 23:46:10.580795 192.168.200.1 > 192.9.200.190: icmp: echo request

  COL-ASA-01 #.

  Any help or pointers greatly appreciated, I have do this config after a long interval on Cisco of the last time I was working it was all PIX so just need to expert eyes to let me know if I'm missing something.

  And yes I don't have a domestic network host to test against, all I have is a switch that cannot route and bridge default ip helps too...

  Hello

  The first thing you should do to avoid problems is to change the pool VPN to something else than the current LAN they are not really directly connected in the same network segment.

  You can try the following changes

  attributes global-tunnel-group RAVPN

  No address RAVPN pool

  no mask RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 ip local pool

  local pool RAVPN 192.168.201.1 - 192.168.201.254 255.255.255.0 IP mask

  attributes global-tunnel-group RAVPN

  address RAVPN pool

  no nat (it is, inside) static source NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 static destination NETWORK_OBJ_192.9.200.0_24 NETWORK_OBJ_192.9.200.0_24

  In the above you first delete the VPN "tunnel-group" Pool and then delete and re-create the VPN pool with another network and then insert the same "tunnel-group". NEX will remove the current configuration of the NAT.

  the object of the LAN network

  192.168.200.0 subnet 255.255.255.0

  network of the VPN-POOL object

  192.168.201.0 subnet 255.255.255.0

  NAT (inside, outside) 1 static source LAN LAN to static destination VPN-VPN-POOL

  NAT configurations above adds the correct NAT0 configuration for the VPN Pool has changed. It also inserts the NAT rule to the Summit before the dynamic PAT rule you currently have. He is also one of the problems with the configurations that it replaces your current NAT configurations.

  You have your dynamic PAT rule at the top of your NAT rules currently that is not a good idea. If you want to change to something else will not replace other NAT configurations in the future, you can make the following change.

  No source (indoor, outdoor) nat Dynamics one interface

  NAT source auto after (indoor, outdoor) dynamic one interface

  NOTICE! PAT dynamic configuration change above temporarily interrupt all connections for users on the local network as you reconfigure the dynamic State PAT. So if you make this change, make sure you that its ok to still cause little reduced in the current internal users connections

  Hope this helps

  Let me know if it works for you

  -Jouni

• Cannot access our local network Web site

  We have just added a Cisco ASA5510 to protect our network. Everything works except that no one in the local network can access our imail we site. Web site points to one of our public IP address, x.x.x.35 (we have access to the web site of outside and we can just? t do inside even after the addition of the ASA). Is it possible inside computers can access our web site using the public IP address? If not, my another option is to set up a record DNS pointing to the web site, for example 192.168.0.213 = www.chicagotech.net (name of the network domain is chicagotech.local)? I can? t find a way to do it. Any suggestions?

  This is the Cisco ASA configuration.

  ASA Version 7.0 (5)

  !

  ciscoasa hostname

  domain default.domain.invalid

  names of

  DNS-guard

  !

  interface Ethernet0/0

  nameif outside

  security-level 0

  IP address x.x.x.38 255.255.255.248

  !

  interface Ethernet0/1

  nameif inside

  security-level 100

  IP address 192.168.0.250 255.255.255.0

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  nameif management

  security-level 100

  no ip address

  management only

  !

  passive FTP mode

  out_to_inside list extended access permit tcp any host x.x.x.34 eq www

  out_to_inside list extended access permit tcp any host x.x.x.34 eq 8080

  out_to_inside list extended access permit tcp any host x.x.x.34 eq 8383

  out_to_inside list extended access permit tcp any host x.x.x.35 eq www

  out_to_inside list extended access permit tcp any host x.x.x.34 eq smtp

  out_to_inside list extended access permit tcp any host x.x.x.34 eq pop3

  out_to_inside list extended access permit tcp any host x.x.x.34 eq 3389

  out_to_inside list extended access permit tcp any host x.x.x.34 eq 13001

  out_to_inside list extended access permit tcp any host x.x.x.35 eq 13001

  out_to_inside list extended access permit tcp any host x.x.x.35 eq 3389

  out_to_inside list extended access permit tcp any host x.x.x.35 eq pop3

  out_to_inside list extended access permit tcp any host x.x.x.35 eq smtp

  out_to_inside list extended access permit tcp any host x.x.x.35 eq 8383

  pager lines 24

  asdm of logging of information

  management of MTU 1500

  Within 1500 MTU

  Outside 1500 MTU

  ASDM image disk0: / asdm505.bin

  don't allow no asdm history

  ARP timeout 14400

  Global interface (10 outside)

  NAT (management) 10 0.0.0.0 0.0.0.0

  NAT (Inside) 10 0.0.0.0 0.0.0.0

  static (inside, outside) x.x.x.34 192.168.0.213 netmask 255.255.255.255

  static (inside, outside) x.x.x.35 192.168.0.112 netmask 255.255.255.255

  Access-group out_to_inside in interface outside

  Route outside 0.0.0.0 0.0.0.0 x.x.x.33 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00

  Timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  If inside users try to connect to the public IP address then, it won't work. How do fix you this depends on where is your DNS server.

  If inside users use a DNS server on the external interface, and then you can have the ASA change the DNS response during its passage through the ASA. Just add the option "dns" on the end of your static controls so that they resemble the following:

  static (inside, outside) x.x.x.34 192.168.0.213 netmask 255.255.255.255 dns

  static (inside, outside) x.x.x.35 192.168.0.112 netmask 255.255.255.255 dns

  If inside users use a DNS server on the inside, but this server responds with the public IP address, so you'll have to change within a file so that it points to your local IP address 192.168.0.21x. No other way around it, I'm afraid.

• ASA 5505 IPSEC VPN connected but cannot access the local network

  ASA: 8.2.5

  ASDM: 6.4.5

  LAN: 10.1.0.0/22

  Pool VPN: 172.16.10.0/24

  Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.

  I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.

  Here is my setup, wrong set up anything?

  ASA Version 8.2 (5)

  !

  hostname asatest

  domain XXX.com

  activate 8Fw1QFqthX2n4uD3 encrypted password

  g9NiG6oUPjkYrHNt encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 10.1.1.253 255.255.252.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  address IP XXX.XXX.XXX.XXX 255.255.255.240

  !

  passive FTP mode

  clock timezone PST - 8

  clock summer-time recurring PDT

  DNS server-group DefaultDNS

  domain vff.com

  vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0

  access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0

  pager lines 24

  Enable logging

  timestamp of the record

  logging trap warnings

  asdm of logging of information

  logging - the id of the device hostname

  host of logging inside the 10.1.1.230

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA-server protocol nt AD

  AAA-server host 10.1.1.108 AD (inside)

  NT-auth-domain controller 10.1.1.108

  Enable http server

  http 10.1.0.0 255.255.252.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 10.1.0.0 255.255.252.0 inside

  SSH timeout 20

  Console timeout 0

  dhcpd outside auto_config

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal group vpntest strategy

  Group vpntest policy attributes

  value of 10.1.1.108 WINS server

  Server DNS 10.1.1.108 value

  Protocol-tunnel-VPN IPSec l2tp ipsec

  disable the password-storage

  disable the IP-comp

  Re-xauth disable

  disable the PFS

  IPSec-udp disable

  IPSec-udp-port 10000

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list vpntest_splitTunnelAcl

  value by default-domain XXX.com

  disable the split-tunnel-all dns

  Dungeon-client-config backup servers

  the address value vpnpool pools

  admin WeiepwREwT66BhE9 encrypted privilege 15 password username

  username user5 encrypted password privilege 5 yIWniWfceAUz1sUb

  the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username

  tunnel-group vpntest type remote access

  tunnel-group vpntest General attributes

  address vpnpool pool

  authentication-server-group AD

  authentication-server-group (inside) AD

  Group Policy - by default-vpntest

  band-Kingdom

  vpntest group tunnel ipsec-attributes

  pre-shared-key BEKey123456

  NOCHECK Peer-id-validate

  !

  !

  privilege level 3 mode exec cmd command perfmon

  privilege level 3 mode exec cmd ping command

  mode privileged exec command cmd level 3

  logging of the privilege level 3 mode exec cmd commands

  privilege level 3 exec command failover mode cmd

  privilege level 3 mode exec command packet cmd - draw

  privilege show import at the level 5 exec mode command

  privilege level 5 see fashion exec running-config command

  order of privilege show level 3 exec mode reload

  privilege level 3 exec mode control fashion show

  privilege see the level 3 exec firewall command mode

  privilege see the level 3 exec mode command ASP.

  processor mode privileged exec command to see the level 3

  privilege command shell see the level 3 exec mode

  privilege show level 3 exec command clock mode

  privilege exec mode level 3 dns-hosts command show

  privilege see the level 3 exec command access-list mode

  logging of orders privilege see the level 3 exec mode

  privilege, level 3 see the exec command mode vlan

  privilege show level 3 exec command ip mode

  privilege, level 3 see fashion exec command ipv6

  privilege, level 3 see the exec command failover mode

  privilege, level 3 see fashion exec command asdm

  exec mode privilege see the level 3 command arp

  command routing privilege see the level 3 exec mode

  privilege, level 3 see fashion exec command ospf

  privilege, level 3 see the exec command in aaa-server mode

  AAA mode privileged exec command to see the level 3

  privilege, level 3 see fashion exec command eigrp

  privilege see the level 3 exec mode command crypto

  privilege, level 3 see fashion exec command vpn-sessiondb

  privilege level 3 exec mode command ssh show

  privilege, level 3 see fashion exec command dhcpd

  privilege, level 3 see the vpnclient command exec mode

  privilege, level 3 see fashion exec command vpn

  privilege level see the 3 blocks from exec mode command

  privilege, level 3 see fashion exec command wccp

  privilege see the level 3 exec command mode dynamic filters

  privilege, level 3 see the exec command in webvpn mode

  privilege control module see the level 3 exec mode

  privilege, level 3 see fashion exec command uauth

  privilege see the level 3 exec command compression mode

  level 3 for the show privilege mode configure the command interface

  level 3 for the show privilege mode set clock command

  level 3 for the show privilege mode configure the access-list command

  level 3 for the show privilege mode set up the registration of the order

  level 3 for the show privilege mode configure ip command

  level 3 for the show privilege mode configure command failover

  level 5 mode see the privilege set up command asdm

  level 3 for the show privilege mode configure arp command

  level 3 for the show privilege mode configure the command routing

  level 3 for the show privilege mode configure aaa-order server

  level mode 3 privilege see the command configure aaa

  level 3 for the show privilege mode configure command crypto

  level 3 for the show privilege mode configure ssh command

  level 3 for the show privilege mode configure command dhcpd

  level 5 mode see the privilege set privilege to command

  privilege level clear 3 mode exec command dns host

  logging of the privilege clear level 3 exec mode commands

  clear level 3 arp command mode privileged exec

  AAA-server of privilege clear level 3 exec mode command

  privilege clear level 3 exec mode command crypto

  privilege clear level 3 exec command mode dynamic filters

  level 3 for the privilege cmd mode configure command failover

  clear level 3 privilege mode set the logging of command

  privilege mode clear level 3 Configure arp command

  clear level 3 privilege mode configure command crypto

  clear level 3 privilege mode configure aaa-order server

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4

  : end

  Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.

  The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.

  On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.