Common ground for a precise measurement and analysis

Similar Questions

• Recommended structure for separation of measurement and control

  Hi everyone, I m going to write a labview program for a test bench that requires to control external devices via the outputs of the NOR-DAQ modules in a chassis usb DAQ and also various measures of tasks via DAQ modules in the same chassis. The output should work for a long time, lets say for about a hour and shouldn´t be interrupted by (i.e. errors in labview code). Measures will be done sometimes but require the variation of some parameters of output. For this type of installation, rather would you recommend to separate the control - and parts of the measure in two screws and allow them to communicate through global variables or rather put in a VI with refined error handling to avoid failure of the output? Or, of course, are there other, better tailored approaches for this friendly task? Thank you for your ideas!

  You should consider master - slave with 1 master architecture and 2 slaves.  A slave can perform control and other measures.

  Intercommunication between the loops: you can use globals or queues. Queues are recommended that globals (freedom of race )

  See rear queries if any.

• Patch for Hyperion Reporting and analysis framework Release 11.1.2.3.000

  Hello world!

  I spend my EMP and other components to 11.1.2.3.500 11.1.2.3 hyperion.

  but could not find patch for Hyperion Reporting and Analysis Framework version 11.1.2.3.000,

  found alone 20029854 Patch: Patch Update: 11.1.2.3.506 for Oracle Hyperion Reporting and Analysis Framework version 11.1.2.3.500

  PSU said he could apply to RA framework 11.1.2.3.500 (my current frame of AR is 11.1.2.3.0)

  1. where can I get patch from 11.1.2.3.0 to 11.1.2.3.500 (any patch number or direct link)

  2. could I ask Patch 20029854 to 11.1.2.3.0?

  Thank you!

  Unfortunately the version of RAF not updated after the patch, have a read of more to life than that...: include the versions of the product in the workspace

  Dear

  John

• I use a Mac.  I "upgraded" to of LR4 LR5.  I don't want to be a member of the "creative cloud."  I just want to use the software that I bought, more precisely to load on my SmugMug account.  Is it possible to use an add-on for this?  Opening and L

  I use a Mac.  I "upgraded" to of LR4 LR5.  I don't want to be a member of the "creative cloud."  I just want to use the software that I bought, more precisely to load on my SmugMug account.  Is it possible to use an add-on for this?  Opening and LR4 were easy, but I think it's impossible without subscribing to CC.

  do you mean that you get a page Adobe Adobe ID, wondering like that? If you have followed my second just method?

  

  If this is the case, this isn't an obligation to subscribe to the CC, but just a completely - a free Adobe ID, email and a password which can identify you.

  In fact, it is the same name of username/password used to log-in on this forum.

• Acrobat 9 Std - Comments-> "enable for commenting and analysis in Reader" option missing

  Hello

  We bought a copy of Adobe Acrobat 9 Standard and must enable the comments in the reader for the PDF files that we create in Acrobat.  The option "enable for commenting and analysis in Reader" seems to be missing in the menu 'comments', even if all the videos/tutorials insist it's there.

  I have not yet found any discussions about this and google search for the lack of option + 'lack' with other things.  Nothing not associated with came.

  Any ideas on what we could try?  Or why it is happening?

  Thank you!

  I don't think that Standard has this option. Acrobat Pro does.

  This page confirms: http://www.adobe.com/products/acrobat/matrix.html

• How to limit the voltage common mode for the switch

  The user manual mentions a maximum of ±12V ground for my switch (pxi-2536) but I do not see an entry in the field on the pinout of the connector. If I have a floating supply, should I connect the ground to the chassis on the ground on the back of the PXI? Is there a better way to limit the common mode voltage?

  Thank you specify, it makes much more sense!  The best way to go about this that seems will be grounded to the negative terminal of your power supply to ground the chassis security, as I think you suggested at the beginning.  I don't know what frame you have, but you should be able to find a "Reason for connection security" section in the manual. For example, here are the 1044 chassis manual, with the present article is on page 2-4. http://www.NI.com/PDF/manuals/371360a.PDF

  This should take care of it and avoid Earth loops!

• I want to allocate more disk space for my c drive and remove the drive d

  I want to allocate more disk space for my c drive and remove the drive d. I 26 gig on the d drive and only using less than 1% of it, and I have the same amount on c, but only 39% c left. How to do this.

  LEM explained the problems that you tried to resize partitions on the same drive.

  You can create more free space in C in carrying one of the measures suggested below.

  The default allocation for the restoration of the system is 12% on your C partition is more generous. I have them would be reduced by 700 MB. Make my computer right click on your icon, and select System Restore. Place the cursor on your C drive select settings but this time find the slider and drag it to the left until it shows 700 MB and output. When you get to the settings screen, click on apply and OK and leave.

  A flaw that might be useless which is for temporary internet files, especially if you keep no copies on the disk offline. Setting the default value is 3% of the walk. Depending on your attitude to copies offline, you could bring it to 1% or 2%. In Internet Explorer, select Tools, Internet Options, general, temporary Internet files, settings to make the change. At the same time, look at the number of days, the story stands.

  The default allocation for the basket is 10% of the disk. Change to 5%, which should be enough. In Windows Explorer hover over your Recycle Bin, right click and select Properties, Global and move the slider from 10% to 5%. However, try to let you become so complete that if it is complete and you delete a file by mistake it will bypass the Recycle Bin and have gone forever.

  You can generate more space in the system (usually C) the folder move partition.

  For temporary Internet files, select Start, Control Panel, Internet Options, temporary Internet files. Settings and move back.

  To move the storage folder Outlook Express select from Outlook Express Tools, Options, maintenance, store folder and change.  http://www.tomsterdam.com/insideoe/files/store.htm.

  How to change the default location of the My Documents folder: http://support.microsoft.com/?id=310147

  You may also change the default locations of the files in Microsoft Office programs when you choose to move the My Documents folder. For Word, go to tools, Options, file locations, highlight the Documents, click on edit and change the path. For Excel, go to tools, Options, general, and change the default path.

  My Documents is one of the many the created system of special folders, which include my pictures, and my music. It can be more easily modified using TweakUi. Download TweakUI, one of MS powertoys, here: http://www.microsoft.com/windowsxp/pro/downloads/powertoys.asp.

  In TweakUi, select workstation, special folders. You can scroll down to see the full list of special folders to the left of the button to change the location.

  You can move programs, but to do this, you must uninstall and reinstall the program. With Word and Excel, the existing data files are not affected by reinstalling. Most of the work in question is going to be reinstall all updates issued after those that are included with the original Microsoft CD / DVD.

  If your drive is formatted as NTFS another potential gain arises with your operating system on your C drive. In the Windows directory of your C partition you will some uninstall files in your Windows folder in general: $NtServicePackUninstall$ and $NtUninstallKB282010$ etc. These files can be compressed or not compressed. If compressed text the name of the folder appears in blue. If these files are not compressed you can compress. Right-click on each folder and select Properties, general, advanced, and check the box before you compress contents to save disk space. On the general tab, you can see the winning amount by deducting the size on disk size. File compression is only an option on an NTFS formatted disk partition / partition.

  I'd be interested to see a report of Disk Defragmenter. Open Disk Defragmenter and click analysis. Select view report, and then click Save as and save. Now find VolumeC.txt in your My Documents folder. Open the file, place the cursor anywhere in the file, select Edition, select all to select all the text and copy and paste into the body of your message. To do this, before you run Disk Defragmenter because it is more informative.

  Select Start, all programs, accessories, System Tools, cleaning disk to emptying your trash, delete temporary Internet files and other selected options. I recommend also you click Other Options, System Restore and delete all but the last system restore point. Run Disk Defragmenter

  Using the system restore option is most appropriate when your system is slow and you need to increase the free disk space on your C partition. If you have errors that could be solved by using the system restore to your system settings back to before that the error occurred initially, do not use this option.

  Select Start, Control Panel, Folder Options, view, advanced settings and check the box in front of "show files and folders" and 'Hide protected operating system files' are unchecked. You may need to scroll down to see the second element. You should also make sure that the box before "Hide extensions of known file types" is not checked. Notwithstanding, there are some files that are hidden. Again, you will not see the System Volume Information folder.

• Initial (and probably more common) question of Dr on SRM and private networks

  Hello

  Can anyone share best practices on the ground with regard to my question archiecture of network:

  According to the guide of the SRM administrator: Mrs. in protected sites and recovery must have access to the same private network (logic).

  We will have protected sites and located on the same ground but both recovery are far from each other on separate parts of the campus and there is network connectivity between sites.

  What are the different ways we can get two separate sites to share a private network?  What is the best practice?

  (1) fiber optic cables directly between sites using Layer 2 switches?  Any potential problem with switching over a distance?

  (2) with Layer 2 VPN MPLS? Enough to handle the traffic scenarios and failover/failback mature?

  (3) should work around SRM to allow a routed 3-layer solution?

  I'm from VMware

  As I said more simple solution is scalable layer 2 making available of VLANS / subnets in two sites in order to avoid the re-ip address of the recovered virtual machine. MPLS and direct DC of interconnection on fiber/xWDM were popular alternatives for the extension of the L2. As with anything there are advantages/disadvantages for things like network and mobile IP service (for example, routing, load balancing, etc.) of persistence or rigidity. The Cisco & VMware following white paper might be of interest that it focuses on a new DCI solution that introduces new options for VM environments. The paper is mainly centered around the Cisco Nexus product range and the ability to now support active/active balancing on various, redundant DC links:

  http://www.Cisco.com/en/us/solutions/collateral/ns340/ns517/ns224/ns836/white_paper_c11-557822.PDF

  You will notice the support of max distance of 200KM that is referenced in the document comes from the limits of support for the underlying storage replication (200KM for most synchronous suites), but there is also the effect of the reactivity of latency and VMotion application considerations. Site Selector Global (Cisco GSS) can be used for the traffic of a smart-balancing the load on the front-end server application as well as for unloading DNS service, DHCP and other common services - it would be more of a supplement to the core DC interconnect solutions mentioned above and not necessarily an exclusive alternative.

  Not sure what you mean by a workaround for Layer 3. SRM has the ability to re - ip of the VM during recovery, allowing you to change all THE info from the network stack inside the VM (network/gateway/dns servers ip/mask) and even generate scripts of ddns, but according to my post previous changing network info is in almost all cases, I worked with a customer "2nd choice".

• SSD for the Scratch, Cache and swap file?

  Certainly, startup disk and RAID3 9-drive (7K 3000) the map of Areca-16. HDDs but... I was wondering, as I refine my construction, on the use of SSDS Strath, Cache and the pagefile.

  It seems to me that constant random access to these files (small for most), could be somewhat competing for overall throughput (they have been configured on the RAID3 alongside media and project). In an ideal configuration, it would be a practical or advantageous to have 2 x SATA3 SSDs RAID0 for Cache, the Scratch and the pagefile? (and whatever else reconstructible temporary structures). In addition, in order to move the traffic far form the Areaca PCIe lanes, would it be more effective to RAID0 on SATA3s to the mobo? What would be the ideal size for these disks (min and max)?  2 x 60GB would do? Or 2x120GB? More?

  I have also heard that, because of the nature of the scratch and cache, it would be better to have them on two separate drives? Or is it just an urban legend?

  Frederic,

  Bays of drive and the system configuration questions are good, but if I or someone had to answer us would be influenced by our own test files, projects, we have worked on, controller CPU, RAM, the card (or the lack of) and much more.

  Given that what you're building has several similarities to mine, I'll share some of my own conclusions. To the topic specific answers like "how many disks in a RAID before it's inconsequential", it depends on so many things you should probably stop asking questions like this, because it may depend on certain things - CODEC, number of layers, transitions, filters, etc..

  Things I'll comment based on similarities between the system you are creating and mine (X 58, 6-core CPU, 24 GB of RAM, controller Areca w / large cache (2 GB or more)):

  1 move the pagefile seems really make a big difference on my system. So therefore, I keep in my table of OS/programs.

  2. faster I ran used two large paintings with the projects, the media and all the files "scratch" on a table and "hide media" and released on the second. While the difference was not huge, the fastest result for PPBM5 comparative analysis was achieved but put 'media cache DB' on my OS/programs, which use SSDS.

  So, how do proceed you?

  1. load your operating system and programs on your disk boot or start table.

  2. set up your Areca and drives in RAID 0, load some concrete projects similar to what you'll be using this system for, and test. Run PPBM5 too, it's a very useful common denominator that can be used to modify your own system and do it before / after comparison of the changes you are trying. IMO, a drive of 9 or 10 RAID 3 or 5 (or 6 besides) works well enough for everything. [Readers here who have a big RAID 0 out of their motherboard, I don't know if this is true for you or not, my test was done with all the great paintings hanging on a controller from Areca]

  3. for answering your question about "Hard drives how much you" on your own system and with your own projects, simply repeat step #2 using a small RAID 0 array. Latest Areca SAS RAID controllers so fast, that I would say that you can count on very similar performance with a RAID 0 array with one less than road when you build the dos system to desired PARITY RAID; with the exception of RAID 6, of course, who would actually perform '2 disks' more small.

  4 configure your final bar selected with parity, load your projects and you're done!

  Another way, you can go forward? (Less time, less optimized, version case potentially filled with several discs, heat and energy than the 'optimal' generation) Note that I tested with a few large RAID 0 arrays that will be in my final build, and I use these disks for the storage of off-site backup.

  1 build your big array with PARITY from the outset.

  2. start to use the system and if it works well for you, you are finished.

  As for RAID 3, 5, 30 and more, I use my table of data for editing more video, so go with RAID 5 was a simple choice for me. That being said, it seems to me that in my system (using a large cache ARECA controller and drives of 1 TB 7200 32 MB cache) a player "a less" RAID 0 seems to work only about the same as a RAID 5, so I don't think that the ineffectiveness of the RAID 5 or RAID 3 for large files (aka video editing) may be noticeable.

  Kind regards

  Jim

• No need for common Modules for A60

  I have an A60 - 180 (PSA60E) satellite. Samewone know where I can find common Modules for Toshiba ACPI (TVALD), because I've lost everythink of them and now I try to get back, but I don't know how.
  Be patient with my English.
  Thanks everywone can help me!

  Hello Viorel

  You can install the original Microsoft OS on your device. All Toshiba drivers you need, you can find the Toshiba site.
  Visit this link: http://eu.computers.toshiba-europe.com

  I m not 100% sure, but I think that you don t need the common Modules of your module, as there is not on the Web site.
  In addition if you want to buy an original recovery CD utility, contact the service partner.

  Good bye

• No need for common modules for Satellite U400 with Win XP

  Hi everibody!

  I'm looking for Toshiba common Modules for Windows XP for Satellite U400-218 PSU44E. Spent a lot of time without results.
  In seeking, fell on wire 55356.

  In his post (July 31, 2010) * Xardas * gave the order of installation for Windows XP and one of the items on the list was "TOSHIBA common Modules.
  This makes me think that everyone (at least * Xardas *) can point to the source of prorper to download the desired file or, if it is already impossible, directly this file send me.

  Thanks in advance!

  Check section driver Toshiba on the European driver page and there is no common Modules available for one of the U400 series.

  Question; Why do you need this tool?

• Satellite A300D - where can I find common modules for XP?

  I got my 300 d satellite with no model no PSAK4E for Windows XP earlier. The only problem is that I can't install the energy saver. The message error «a fatal error has occutred, code 0 x 2» I discovered that this has something to do with the common modules, which I do not think that I have installed.

  However, the problem is that I can't find the common Modules on drivers Toshiba's Web site. Is there another name for the common modules, or are they simply not there?

  I want to reinstall Windows in order to install the common modules first. However, it is a little difficult without this having the installation package. I already tried to do some research on the subject but can't find the right information on my model. I found a few 3rd party software but I don't know if it's a good idea.

  Could someone help me, or indicate where I can find the common modules for my model?

  Hello

  The common Modules are not available for models A300D.
  Person not A300D series needs this module.

  But I found some other Power Saver for Satellite A300D series.
  I chose to ve on the Toshiba European pilot page this:
  -> Satellite A satellite-> Satellite A300D-> all-> Win XP.

  Now, I see two energy saving; 7.04.02.Q and v 7.04.02 v

  Check both

  Before install you it, delete the old version, clean the operating system using the CCleaner, reboot the laptop and try to install once again.

• Calibration Toolkit with 3rd party ECU measurement and CAN interface

  I would use the NI ECU Measurement and Calibration Toolkit with an NI CAN interface.  The interface devices supporting J2534 are very common.  The NI ECU Meas and Cal Toolkit allow this? If so, how does one time on another interface CAN interface to the Toolbox?

  The NI ECU Measurement and Calibration Toolkit National Instruments Hardware only supports.

  If you want to discuss the possibility of using any 3rd party hardware, please contact your representative local.

• measurement and automation

  I'm just starting using the measurement and Automation Explorer.   Half an hour ago, I performed a calibration of temperature to get familiar with the process.  It seemed to work.

  I tried calibrate again.  It says my current calibration is 31/12/1903 - Question 1) why is this?

  I pressed the button , then came the name of my Stallion, then

  I left the characteristics of calibration because it was one of the screen: 1000 samples at a frequency of 1000 hz, then I pressed

  I received the following message is displayed:

  Error 50103 the DAQ Assistant.  -Question 2) what is this error code for

  Question 3) where can I find a list of error code numbers and their meaning?

  Thank you

  jdsnyder

  OK, now the problem is finally solved!  I re - adjust the device.

  At work the first time, he then had to be reset.

  Thank you

  Jon SNyder

• How to measure and mark the value of real-time data?

  Hello

  I need to measure and trace in time real RMS value of EMG power. I did a VI. But I don't know why it didn't work. Can someone help me please? My VI is set in 2013 and 2011 both version. An example of data is also attached. Thanks in advance.

  Taslim. Reza says:

  I tried RMS PtByPt VI. But it has not been wired because the source was table 1 d of double and double sink.

  Well, ptbypt tools affect only one value at a time, so you must place them in a loop FOR. Here's how.