Communication with a host esxi 4.1 problem

Similar Questions

• Services of files in Microsoft Clustering with failover in ESXi 4.1

  Helllo,

  I have a virtualization environment with 5 hosts ESXi 4.1 on location A and two hosts ESXi 4.1 location B, all with high availability, which is the host 7 ESXi 4.1 are highly available.

  I need to set up a file of Microsoft with Failover Clustering in ESXi 4.1

  I want to create a file from Microsoft with Failover Clustering with 3 VMs that are 2 VM on a location and 1 VM on site B.

  Geographic VM cluster is supported by vmware?

  What is the maximum nodes in the cluster in guest virtual machines?

  Thank you

  jVidalll

  Welcome to the community,

  Only 2-node MSCS is supported in ESX (i)

  Take a look at http://kb.vmware.com/kb/1004617 for links to MSCS documentation.

  André

• Problem with getting communication with old instrument GPIB-ENET/100

  Hello!

  I'm trying to get my program in VB.net to communicate with an older instrument (Infratek 305 A, measure of power) via a GPIB-ENET/100 device.

  The manual of the instrument does not say what GPIB standard, it supports, but the instrument is detected by the measurement and Automation Explorer.

  Detected by that I mean that MAE has detected an instrument located on the right GPIB address, but indicated identification is the output measure instrument string

  instead of the name of instrument (as shown for some more recent instruments of Agilent).

  When I run my application, I followed the communication with NISpy.

  Configuration of the device seems to work and I present only once in the program.

  The problem is reading data from the instrument. Whenever I read the data, I get a correct string of the instrument. But the problem is

  I get the same data in two consecutive and all readings first after that I get new data and also these new data are received in two consecutive readings.

  According to the manual of the instrument the instrument generates the data as follows:

  "A row of data ends with CRLF. The instrument can send multiple rows of data. "When all of the data transfer is complete the EOI (end or identify) is sent.

  My endpoint settings are:

  Send EOI to write complete: YES

  Terminate read on EOS: No.

  EOS byte: 2

  8 bit EOS compare: YES

  Define EOI with EOS on write: No.

  How can I configure the GPIB-ENET/100 to work with my instrument?

  Here are som NISpy logs:

  # Configuration #.

  61 ibwrt(UD3, "C0C2C4C8..", 10 (0xA))
  PID: 0x0000113C Thread ID: 0x000008B4
  Departure time: 13:54:43.671 call duration 00:00:00.079
  ibsta: 0 x 100 iberr: 0 ibcntl: 10 (0xa)

  62 ThreadIbcntl()

  PID: 0x0000113C Thread ID: 0x000008B4
  Departure time: 13:54:43.750 call duration 00:00:00.000
  ibsta: 0 x 100 iberr: 0 ibcntl: 10 (0xa)

  63 ibwrt(UD3, "K0K3K5K9..", 10 (0xA))
  PID: 0x0000113C Thread ID: 0x000008B4
  Departure time: 13:54:43.765 call duration 00:00:00.125
  ibsta: 0 x 100 iberr: 0 ibcntl: 10 (0xa)

  64 ThreadIbcntl()
  PID: 0x0000113C Thread ID: 0x000008B4
  Departure time: 13:54:43.890 call duration 00:00:00.000
  ibsta: 0 x 100 iberr: 0 ibcntl: 10 (0xa)

  65 ibwrt(UD3, "F14F18F24..", 11 (0xB))
  PID: 0x0000113C Thread ID: 0x000008B4
  Departure time: 13:54:43.890 call duration 00:00:09.250
  ibsta: 0 x 100 iberr: 0 ibcntl: 11 (0xb)

  66 ThreadIbcntl()
  PID: 0x0000113C Thread ID: 0x000008B4
  Departure time: 13:54:53.140 call duration 00:00:00.000
  ibsta: 0 x 100 iberr: 0 ibcntl: 11 (0xb)

  ### LU ###

  437 ibrd(UD3, "*AC/1.0A480V/...", 1024 (0x400))
  PID: 0x0000113C Thread ID: 0x000008B4
  Departure time: 13:58:52.484 call duration 00:00:00.094
  ibsta: 0 x 2100 iberr: 0 ibcntl: 225 (0xe1)

  438 ThreadIbcntl()
  PID: 0x0000113C Thread ID: 0x000008B4
  Departure time: 13:58:52.578 call duration 00:00:00.000
  ibsta: 0 x 2100 iberr: 0 ibcntl: 225 (0xe1)

  439 ThreadIbcntl()
  PID: 0x0000113C Thread ID: 0x000008B4
  Departure time: 13:58:52.578 call duration 00:00:00.000
  ibsta: 0 x 2100 iberr: 0 ibcntl: 225 (0xe1)

  Hello!

  I don't have the opportunity to test with other controllers.

  However, I found a solution to my problem.

  The instrument should output 4 lines of data.

  L1 - line with comments

  L2 - line with current values

  L3 - line with the values of voltage

  L4 - line with power values

  The first line of the reading stops the instrument of implementation of additional measures.

  The measurements in the instrument began reading the last line of data (L4)

  The problem was that the instrument for a reason any also released a fifth line, which was empty.

  Read this line 5' th stopped the instrument again.

  By configuring the HW to finish reading on EOS, with EOS PMQS, the value byte, I could read the

  buffer of the instrument with a line output instead. This way I could read just L1 - L4

  and the instrument could work again.

  Next time I should read data from the Instr. first of all, I would like to read the empty line, then

  L1 - L4.

  Why the outputs Instr. an additional empty line will be left not resolved.

  My problem is solved.

• Each time after clicking the icon of user account on windows xp to change a password is crashes with this error message: Microsoft (R) HTML Application host has encountered a problem and needs to close.

  Each time after clicking the icon of user account on windows xp to change a password is crashes with this error message: Microsoft (R) HTML Application host has encountered a problem and needs to close.

  There is a Microsoft Knowledge base article which sets up a few steps to perform in the computer in order to solve the problem you are experiencing, read the article that you find on the link I am mentioning below and see if it helps the measures mentioned:

  http://support.Microsoft.com/kb/919751

• Problem of the printer, I get "the computer is unable to establish two-way communication with the device.

  Original title: printer problem

  "The computer is unable to establish two-way communication with the device. I have pluged a all cables and pluged in that they return.

  Hello
   
  1. What is the brand of your printer?
  2. when the question is is produced?
  3. you remember to make changes to your computer before the problem?
  4. when exactly you get this error?
   
  I would temporarily disable all security software and check if the problem persists.
   
  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off
  
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software
   
  Note: Antivirus software can help protect your computer against viruses and other security threats.  In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.
   
  If you have an HP printer, you can consult the links below.
   
  http://h10025.www1.HP.com/ewfrf/wc/document?LC=en&DLC=&cc=us&DocName=c01868684&product=3737195
   
  http://h10025.www1.HP.com/ewfrf/wc/document?LC=en&DLC=&cc=us&DocName=c00301806&product=407677
  
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Windows has encountered a problem communicating with a device connected to your computer. Status: 0xc00000e9.

  * Original title: 0xc00000e9

  Hi all

  I had a problem - would be great if someone could help me!

  =====

  Windows has encountered a problem communicating with a device connected to your computer.

  This error...

  File: / Boot/bcd

  Status: 0xc00000e9

  Info: An unexpected i/o error has occurred

  ==========

  I press ESC = exit or enter = continue it tries to start, but eventually back to the black screen. So I can't pass this screen. I do not of hava a recovery for Windows disk... And the laptop is a Sony Vaio with Windows 2008. A couple of days, I have connected to my work through the laptop environment and forgot to close - battery went down--and now this...

  Can anyone help?

  Please see the message (response) by Afsal Taher:
  http://answers.Microsoft.com/en-us/Windows/Forum/all/new-computer-running-Windows-7-unexpected-IO-error/46b4fc7a-9a83-4db2-9a00-dca512797e61

• Windows has encountered a problem communicating with a device connected to your computer.

  When you start the computer laptop, windows Boot Manager appears.

  He reads

  Windows has encountered a problem communicating with a device connected to your computer.

  file: \Boot\BCD

  status: 0xc00000e9

  Info: an unexpected i/o error has occurred.

  When I I go through F8, safe mode, last known good configuration, running in debug ect mode.

  running in safe mode past with him, freezes for abit in the past to a black screen with just the cursor and the Center recovery running VAIO, last good configuration, known debug mode. This windows is loading files, then the windows boot screen were it freezes then goes to a black screen with just a cursor.

  Place the cursor, I am unable to do anything else on this screen.

  is it far from getting the laptop to function normally again or is it finally the end of his life?

  the laptop is a sony VAIO E series (VPCEA25FG) running under windows 7.

  Hello

  The error - an unexpected i/o error has occurred, status: (0Xc00000e9) is a material error in the BIOS of your computer.

  Basically, it's to tell you that the computer is not able to communicate effectively with the hard drive.

  Try the Startup Repair.  Startup Repair is designed to prevent a reinstall tedious to diagnose and repair problems that prevent Windows startup.

  To run the Startup Repair tool, see the links below for more details:

  What are the system recovery options in Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  
  

  Startup Repair: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/Startup-Repair-frequently-asked-questions

  I also suggest you to update the BIOS. Update the BIOS, contact the manufacturer of the system!

  Warning of the BIOS:

  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  To ask your question in the Forum of Sony, refer to this link.

  http://community.Sony.com/?XID=M:header:eSupport

• PowerCLI defining politics NTP to "Start and stop with the host" in ESXi 5

  Would appreciate any help in the definition of the strategy NTP on ESXi 5 hosts 'start and stop with the host. My script is currently using the following:

  Get-VMHost MyEsx | Get-VMHostService | where {$_.} Key - eq 'ntpd'} | Game-VMHostService-policy "automatic."

  This sets up the NTP service in "start automatically if all ports are open and stop when all ports are closed.

  "When I cange to 'MyEsx Get-VMHost | Get-VMHostService | where {$_.} Key - eq 'ntpd'} | Game-VMHostService-political ' market / stop with host"" the following is returned:

  «The possible enumeration values are "auto, On, Off«»»»

  Anyone know of a way (in PowerCLI) of the set up for the 'start and stop with host?

  OK, then you should choose politics "on".

  These are the policy values and what they match.

  

  Like this

  Get-VMHost MyEsx | Get-VMHostService | where {$_.Key -eq "ntpd"} | Set-VMHostService -Policy On
  

• Error during communication with the remote host when you create the new virtual machine

  I'm under 7 ESX servers on IBM Blade H22 there is a mistake to invite while I create a new virtual machine

  on the vcenter Server

  At the end of 30-35 minutes, it gives an error

  "Error during communication with the remote host"

  The existing machines are working well... I tried to create virtual machines to other ESX servers as well

  but the same question. I also tried to make the clone of existing machines, but without success

  Can anyone help?

  You rescan the LUNS once?

  You've restarted the management agent?

  You've restarted the vpxa?

  If this isn't the case, please perform the step above and check out them.

• Restart host ESXi 4.0 with vCenter 4.0 as a virtual machine

  I have two hosts ESXi 4.0:

  1. the host 1 has vCenter 4.0 installed as a virtual machine with a VMware data recovery VM and some other virtual machines.

  2 host 2 has a number of virtual machines.

  I want to restart the first host and level to ESXi 4.0 Update 1 - I won't stop VMs on host 2, and I want to improve it yet.

  My plan is to stop all VMs on host 1 letting the vCenter VM until the last. I have then place my host in maintenance mode and run the host update application to install the update which will then require a restart of course. Once restarted, I'll connect to host 1 directly by using the vSphere client and restart the VM vCenter. I will then restart all my other virtual machines.

  Is this sound OK? VCenter will restart Fortunately?

  You can also power off the vCenter, register on the other (ESX) If you have the shared storage and try again.

  Be sure only to say I_moved about the question that appear when you turn on the virtual computer.

  André

• Where to download the file ZIP ESXi 4.0 for inplaceupgrade with vSphere Host Update Utility

  I'm updating my ESXi ESXi 4 3.5U4 with the Host Update Utility vSpheer.

  But where can I find the ZIP file that is required for the upgrade?

  Can this ZIP file created from the ISO?

  There are only ISO in downloads...

  Kind regards

  Daniel

  It is available here:

  https://www.VMware.com/tryvmware/p/activate.php?p=free-ESXi

• IPSec VPN with DynDNS host problems after change of address

  Hi guys,.

  I have a weird problem on an IOS router.

  I need to implement IPSec VPN L2L.

  Because of the security requirements of each site needed a clean pre-shared key. Sites dynamic IP and it's

  why I use dyndns.

  ISAKMP crypto key KEY hostname XXXXXXXXXXX.dyndns.org

  CMAP_1 1 ipsec-isakmp crypto map
  define peer dynamic XXXXXXXXX.dyndns.org

  First of all, it works fine, but after the change of IP address it no longer works.

  Debugging, I discovered that it resolves the new IP address but IPSec attempts to connect to the previous INVESTIGATION period.

  I tried this on two other IOS, 15.0 and 12.4

  This debugging output:

  01:02:39.735 Mar 1: IPSEC: addr of Peer Link70 (70.1.1.3) is out of date, triggering DNS
  * 01:02:39.735 Mar 1: IPSEC: Peer has the address 70.1.1.3 (DNS cache).                 New IP address
  * 1 Mar 01:02:41.731: IPSEC (sa_request):,.
  (Eng. msg key.) Local OUTGOING = 1.1.1.2, distance = 70.1.1.200, OLD IP
  local_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4),
  remote_proxy = 10.254.70.0/255.255.255.0/0/0 (type = 4),
  Protocol = ESP, transform = esp-3des esp-sha-hmac (Tunnel),
  lifedur = 240 s and KB 4608000,
  SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 0
  * 1 Mar 01:02:41.739: ISAKMP: (0): profile of THE request is (NULL)
  * 01:02:41.739 Mar 1: ISAKMP: created a struct peer 70.1.1.200, peer port 500
  * 01:02:41.739 Mar 1: ISAKMP: new created position = 0x673FB268 peer_handle = 0 x 80000008
  * 01:02:41.739 Mar 1: ISAKMP: lock struct 0x673FB268, refcount 1 to peer isakmp_initiator
  * 01:02:41.743 Mar 1: ISAKMP: 500 local port, remote port 500
  * 01:02:41.743 Mar 1: ISAKMP: set new node 0 to QM_IDLE
  * 01:02:41.743 Mar 1: insert his with his 650AE400 = success
  * 01:02:41.747 Mar 1: ISAKMP: (0): cannot start aggressive mode, try the main mode.
  * 01:02:41.747 Mar 1: ISAKMP: (0): no pre-shared with 70.1.1.200!                     PROBLEM!
  * 1 Mar 01:02:41.747: ISAKMP: (0): pre-shared key or Cert No. address.                   PROBLEM!
  * 1 Mar 01:02:41.747: ISAKMP: (0): construct_initial_message: cannot start main mode
  * 01:02:41.751 Mar 1: ISAKMP: Unlocking counterpart struct 0x673FB268 for isadb_unlock_peer_delete_sa(), count 0
  * 01:02:41.751 Mar 1: ISAKMP: delete peer node by peer_reap for 70.1.1.200: 673FB268
  * 01:02:41.751 Mar 1: ISAKMP: (0): serving SA., his is 650AE400, delme is 650AE400
  * 01:02:41.755 Mar 1: ISAKMP: (0): purge the node-267512777
  * 01:02:41.755 Mar 1: ISAKMP: error during the processing of HIS application: failed to initialize SA
  * 01:02:41.755 Mar 1: ISAKMP: error while processing message KMI 0, error 2.
  * 1 Mar 01:02:41.759: IPSEC (key_engine): had an event of the queue with 1 KMI messages...
  Success rate is 0% (0/5)

  I'm building a lab to find a solution for this.

  The other side is a VPN Linksys router, I tried with an IOS router on both sites also, but I got same results.

  I tried with DPD, ISAKMP profiles don't... no help.

  Hi Smailmilak83,

  Configuration of a static encryption with a specific peer card creates a society of surveillance for the peer. Dns lookup he's now only the first time, he tries to connect, after which it's just going to be her generate a new key. If she would ideally use the value peer in the his and not the config or a dns lookup. So, it is wise to use a dynamic encryption card.

  Please try to use a dynamic encryption instead of a static map. Although there are some limitations including crypto being initiated only at the other end, we can work around keeping the tunnel directly.

  Hope that helps.

  Sent by Cisco Support technique iPhone App

  -Please note the solutions.

• Restore directly to a host ESXi with VMware Data Protection (WTP)

  Can I use VMware Data Protection restore directly to a host ESXi, or do I have to have vCenter Server running? (If the virtual machine, I am trying to restore is vCenter Server itself, then it won't work unless I can restore to a host ESXi directly without using vCenter Server...)

  You don't need a vCenter running for the restoration of emergency (directly to the host).

  You can also use this direct restore to restore a vCenter to a host. I think this is the main reason that this feature was developed

  Edit: More on it in vSphere Direct-to-Host Data Protection's emergency recovery. VMware vSphere Blog - VMware Blogs

  Concerning

• The upgrade to vCenter Server 5 with a view Server 4.6 on a host ESXi 4.1

  We have guests ESX and ESXi 4.1 and just got a new host ESXi 5. We must now be upgraded vCetner to version 5 server in order to manage the new host. I know 5 4.1 manage vCenter hosts but do I need to be wary when it comes to the host that maintains the virtual computers view or the view Server 4.6 VM itself?

  According to the comapbility matrix View 4.6 is not supported under vSphere or vCenter 5.

  http://PartnerWeb.VMware.com/comp_guide2/SIM/interop_matrix.php

• Communication between two hosts on the host only

  I have a host ESXi 5.5 with two reviews, a Linux / Centos 6.5 comments and a guest Server R2 2012.

  I've muddled through many questions - time zone, being the biggest problem, but am confused on how to get these guests to see one another, not even sure what to put in Google.

  My goal is to be able to share files between the two guests and access their consoles with putty and RDP, but I can't make them one ping to another. Everyone on the LAN can connect these two guests, but they cannot see.

  A kind soul told me that I forgot?

  Thank you

  Hey katycomputersystems,

  Could you give us a quick screenshot of your vSwitch / Port groups.

  Of the IP information you should be able to ping to each of the systems if they are on the same vSwitch / Portgroup / VLAN.

  Try this

  vSwitch0

  VM Network - Port Group - VLAN 110 - physical Nic don't matter we will keep all the VMS on this port group

  Configure all your VMS on the port network of VM group.  As long as all the VM living on the same port group vlan and vSwitch traffic should never leave this vSwitch and each VM must be able to communicate with each other.  If not you can always ping each other take off the VLAN and try again.  Make sure also that you have no firewall or tables ip enabled on the operating systems that could prevent communication.

  Let us know how it goes