Compaq presario f600 video dissbled in cmos

Laptop Compaq presario f600 I set the video memory to none in the cmos an option and now get 3 beeps and no startup just stops any correction or is - this toast?

Thank you very much for your help. It worked! F.Y.I: on the f600 the cmos batter is not removable, and it is in the compartment of the memory with a lead wire to the motherboard. However, due to the knowledge of ypur and suggestion, I searched and found. I unplugged, waited a few minutes, reconnected, put everything in place, have pulled up and went directly to the display of the cmos. Once again, thanks a lot for your knowledge.

Tags: Notebooks

Similar Questions

  • Compaq presario m2000: video controller for win 7 [bit]

    I have compaq presario m2000 laptop I upgraded from win xp to win 7 (32 bit) I miss the video controller.

    Hello:

    You must manually install the driver Windows XP to get the graphics to work.

    You will not have Windows Aero because the Intel graphics card that has your laptop does not support Aero.

    Download and run this driver.  Conclusion of any windows error that can occur.

    This contains the Windows XP driver for the Intel 82852/82855 GM/GME Graphics controllers in the listed notebook models.

    File name: sp28484.exe

    Go to Device Manager and click on the video controller needing drivers.  Click the driver tab.  Click on set to update driver.

    Select travel it my computer for the software driver and then at the bottom of this list option, click Let me pick from a list of drivers for devices on my computer.

    Click on disk, then go to: C:\SWSetup\sp28484\ialmnt5 and select the Intel (r) 82852/82855 GM/GME Graphics Controller in the list and see if the pilot goes like this.

    Then reboot and you should be able to change the screen resolution.

  • Compaq Presario C700 video card

    I have a Compaq Presario C700 computer laptop (C769US) and I was wondering if I would be able to upgrade the video card to play Fallout 3, that I bought yesterday. The card that is here right now is 'Intel 965 Chipset family' or something of the kind.

    I would like to put this here: http://www.bestbuy.com/site/olspage.jsp?skuId=8761878&type=product&id=1202650704648

    It will go? My father said something about PCI and AGP, I don't know how to find out if mine is PCI.

    Any help would be appreciated, thanks.

    -Chris

    If you put beside the video card laptop I think that you see that there is no way to put it there. The video card is almost as large as the laptop. We receive a few tons of these posts here these days. But the answer has not changed. There is no upgrade for your video that is remotely possible in this life on this planet. Cannot be done, no cases in any way. The video is a chip that is soldered to the motherboard with the set traces to work only with this specific chip. Even the best ubertech with mad fine welding skills could not do anything else's work. When you buy a laptop get the graph and the processor you want and need for now and the future. If you need something better it means a new laptop not a level 98% of the time. When you buy a game controls the minimum requirements and see if your computer can meet.

    Sorry if I sound a little harsh but as I said we get 2 or 3 of these questions every day and I blame the computer manufacturers (HP, for example) and retailers such as Best Buy for not educating the public about what they are buying.

  • HP Compaq Presario SR5350F - video card with S video output

    Hello my name is Ken

    Please could you recommend the best video card with a S-video port so that I can connect my computer to my

    50SBX70B HITACHI UTRAVISION PROJECTION TV. I want to connect the computer to this TV because it has two video ports S, thank you for your time and your advice. Bravo sincerely, Ken

    Hello

    Please try:

    http://www.eBay.com/ITM/new-ATI-Radeon-9200-128MB-desktop-VGA-TV-out-Vista-XP-PCI-video-card-/390730212270

    or PCIe (better):

    http://shopper.CNET.com/graphics-cards/NVIDIA-GeForce-8400GS-graphics/4014-8902_9-32610077.HTML?tag=mncol; LST

    Your computer has two PCI ports free and a PCIe x 16 location. The card uses a slot. And should be ok for 250W power supply

    Kind regards.

  • Compaq presario cq5320f video card update

    Can someone tell me what are the choices that I have to update my video card on this machine without changing the power supply? Enter the game on PC more. Thank you!

    There is really no quality maps of game on the market for your computer's power supply. 250 watt power supply is too low for this kind of maps and will need to be replaced if you want use more add-in PCIe x 16 graphics cards.

    Frank

  • Compaq Presario SR5214x: Replacing the CMOS battery for Compaq Presario SR5214x desktop computer

    How to replace the CMOS battery on a Compaq Presario SR5214x desktop computer. What type of battery? Where is the battery? Thank you (deleted content)

    @ernier

    You will find how to do here.

    http://h10032.www1.HP.com/CTG/manual/c00840496

    REO

  • computer Compaq Presario SR1950NX is compatible with the Radeon 9250 128 MB DDR (64-bit) video card

    I was just curious to know if I could install this 'Radeon 9250 128 MB DDR (64-bit) video card"who collects dust for a long time in my old computer Compaq Presario SR1950NX I bought in 2006.

    I know that the video card is still older than the computer, but it was almost 200$ 7 years and it would be nice to see it put to use again. I heard that the motherboard on this computer is not terrible, and there may be not enough power to run this video card.

    I am running windows XP if it means something.

    Thank you.

    Yes. Your PC does not have an AGP slot. No place to put it.

  • Compaq presario video card driver?

    Anyone know what graphics card for compaq presario sr1717cl manufacturing is?

    Hello:

    If you do not add a video card, the standard video card came with the PC is the integrated ATI Radeon Xpress 200 graphics.

    Paul

  • Compaq Presario 2034NX. N power supply video card update

    I have a Compaq Presario 2034NX and want to get an upgrade of the installed video card (for a HDMI output, etc.).  I know that I have to spend my diet as well, for new power requirements.

    I am interested in (after-sales) part 3 parts, not "genuine HP/Compaq", to save costs on this box of 7 year and longer.

    (A) what version of PCI-Express is the slot on the MBoard?

    (B) what form of power factor should be purchased for?  ATX?  12V?

    (C) is there a special condition of type MOE for video work in Compaq Presario PCI-Express slot card, or will more 3rd party (after-sales) cards work?

    Thank you!

    Hello

    Is the Compaq Presario PC?  If Yes, then put a standard size ATX power supply will work as well as several video cards PCI-E x 16.

    Most of NVIDIA video cards require a minimum of a 300 Watt power supply.  Most of ATI video cards require a power supply of + 400 watt mimium.

    1 HP didn't post the version of PCI-E slot, but I suspect 1.x. It should support most of the cards PCI-E 2.0 with a few exceptions.

    2. a stand size ATX power supply will fit (5.5x3.4x5.9).

    3. the video card chosen must be associated with a power supply to support its power requirements.

    How much budget do you see for the video card and the power suppy.  You have special requirements of video connection? (HDMI, DVI, VGA)  What applications are you planning to use with the new video card?

    Open your PC and a few measurement in parallel with the PCI-E x 16 slot to see how long of a video card will fit. The adjacent slot on the PCI-E x 16 slot must be vacant if a larger video card is being considered. Look at the motherboard, and ensures that the components on the motherboard will not interfere with the installation of the video card.

  • Presario CQ60: Reset CMOS password for compaq presario CQ60

    Son compaq presario CQ60 will not feed goes right at the request of password cmos don't care about data on PC I change OS to LINUX. Password entry I tried three times bleached with 13708 code can help you me reset so I can get my sons PC up and running again thanks in advance, you send all help to address and email please

    Hello

    Enter: nkhtrc

    or

    xjpfgn

    Kind regards

    DP - K

  • laptop Compaq presario 2701T: battery cmos

    I need to replace the CMOS battery on my laptop Compaq Presario 2701 T and would like to know if the battery is located on the laptop and how to get it out.  In addition, if you may know where I can buy this point.

    Thank you.

    I finally found where the CMOS battery on my laptop Presario 2701.  I tired going road to tech support but I was told that my laptop was out of warranty so that they could not help.  Then I noticed that you can send the President of HP if you have a problem, so I did it, said my question and the next day I received a call for technical support and I was told the battery was under the rear cover of the laptop.  So after unscrewing which seemed to be a dozen screws on the bottom of the laptop I tried to remove the cover, but there do not seem to come off.  I then handed the laptop and pried off the keyboard, carefully removed the keyboard Ribbon that has two small tabs on each side that you just have to push back on.  Then you will see a square on the left side cover, remove the four screws, remove the cover and there is your CMOS battery in the upper right corner.  It is a flat regular silver oxide, number 2032 battery.  Replace the battery and put that together and it started right.  Changed the date and time and the computer is running back to normal.

  • Compaq Presario SG2-210UK: Compaq Presario SG2-210UK change cmos battery

    Clock will not keep time. How can I change the cmos battery in my all in a Compaq Presario SG2 210UK.

    You will need to unplug and open the AIO PC. Do you need instructions on how to do it?

    Go to the following URL. Login with the same username and password you can access the HP forum.

    http://h20574.www2.HP.com/results.htm?SID=4269843&MEID=76630F1A-89A3-41C5-A04C-BFD1E24D24A5

  • Compaq Presario S5000T P8656Q - ABA NA310 motherboard? The information that is required for the replacement of the video card.

    My best friend has an ATI Radeon 9200 SE (Shader 1.0 / DX 8.0) and wants to run a program that requires the Shader 2.0 / DX 9 .0c

    I'll try to find a compatible video card; I don't know if the motherboard for the NA310 of P8656Q-ABA S5000T Presario is AGP 2 x or 4 x.  I tried to find on the ' net, but no luck. Graphics (Radeon 9550 for $24 again), I found is AGP 4 x / 8 x, so I don't want to buy this if the MB is only AGP 2 x.

    Also, I guess the 200/250w PSU would be sufficient for a 9550? It only uses the pc for MS Word, a bit of Youtube and 1 or 2 older games.  If not, anyone know a cheap video card which is AGP or PCI that is capable of Shader 2.0? It is for the sake of compatibility of XNA Framework.

    Thank you!

    It seems that the Compaq Presario S5000T desktop computer specifications are no longer available. With this information we can only guess what this thing has AGP connector. Based on HP and Driver Downloads page software, this model uses a 'P4SD - LA motherboard". The only problem is that the 'P4SD - LA"is available in different version at least four over time... Oxford, Cobra, Stingray, Yale, etc.. The good news is that it seems all support at least an AGP 4 x connector and most support a 4 x / 8 x slot.

    Please send BRAVO

  • I have a Compaq Presario V6000 Widescreen and I can't find the video driver just for this computer

    I can find the video driver for my Compaq Presario V6000 Widescreen

    Serial number: {Private Information Removed}

    There are 4 computer V6000 but I don't know which one should I use.

    I use my serial number and the model name and the PIN code and still cannot very well the video driver.  can someone tell me were fined the pilot to be used on window XP

  • Compaq Presario S4500UK won't start after disconnecting from the wall outlet. What is a CMOS battery problem?

    Reconstruction of recent software with HARD drive internal extra (March 2011) under Windows XP/Linux dual-boot installation worked fine.  CD/DVD RW drive, started giving errors so replaced cyclic redundancy check drive a week ago.  All still OK.  Change of electricity supplied and increases energy use conciousness off the machine to the outlet of the overnight after normal shut down.  Machine will not re-start not in the morning.  Not load BIOS; all lights came briefly and then die after 3-4 seconds with power still led on.  You can get a similar effect by plugging the keyboard into the PS2 Mouse Jack I did once!

    After 20 minutes or so try all kinds of things managed to boot from the CD of Linux.  Shut down/restarted and everything is fine so I don't switch off at the wall.  Also seems to be OK after brief power off for 5-10 seconds but the problem persists with any long disconnection.  It seems that after 10 to 15 minutes from power-on and 2-3 attempts to restart, BIOS comes up and all is well, but he stopped in the middle of a start of Windows or Linux on a couple of occasions.

    Am I right in thinking the problem might be the result of a dead CMOS battery?  The reason that I ask is that the clock seems to keep time OK and there is no apparent problem with the BIOS once it loads.

    Any help/advice would be much appreciated.  New config info below.

    Dual boot Windows XP Pro SP3 of Compaq Presario Bios v3.03 S4500UK / Linux Ubuntu 10.04 Lucid (2.6.32 - 33)

    Drive HARD 120 GB (original Seagate Barracuda 7200) Master Boot Record, Partition Table, Windows XP, Linux, Swapfile etc.

    500 GB Western Digital Caviar Blue (encrypted)

    CD/DVD-ROM (original JLMS XJ-HD166S)

    Recently installed HL-DT-ST DVD - RAM GH22NP21 replacement NEC ND - 1100

    +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

    I don't have all the answers so I went forward with replacing the CMOS battery, but that did not help.  The problem is also obvious if I turn it off and leave it for an hour or more before trying to restart even if I do not unplug the wall plug.  It seems to take about 15-20 will start again before it fires.  I would be really grateful for any clues as to what is wrong.

    TKS

    JG1

    OK, guys.  I finally solved the problem.

    After you have calculated the power needed for the config curent, I discovered that, using various ways to estimate, he walked between 321W - 383W.  It was pretty weird that the only thing I added was a HARD drive and a memory stick and the wisdom of the other guys on this forum, it's that there is a lot of capacity within the factory installed power of 250W.  Yes and here's the rub: the modern replacement devices usually have upgraded capabilities and use more power.  And so when I replaced the drive CD/DVD RW added a few watts, as the sectoral approach of the floppy drive.  It appears also that the optical USB mouse needs more juice than the good old PS2.

    I just installed a new 450W PSU Powercool and Bingo!  The processor is faster, too.

    Hope that my pain and trauma saves someone else having to suffer the same.

    JG1

Maybe you are looking for

  • Scrolling problem

    I have the scrolling problem in netbeans IDE in my macBook pro early 2015 (retina 13 inches), somewhere that is extremely fast cannot see what is happening and in a place more slowly scrolling and not able to fix by increase or decrease scrolling spe

  • I can use it on Microsoft 8.1

    When I upgraded my computer from Microsoft 8.0 to 8.1. I had some problems with my e-mail (outlook) feature that was part of Word 2003 that put on my computer. AutoFill shows me the addresses when I type the first or the second letter of an address,

  • How can I keep my awesome bar list of sites

    This morning, something has changed. When I opened firefox, all sites previously listed in the bar of the so-called great disappeared. I have re-registered, but when I open the browser again, they disappeared again. what I did that could have changed

  • build error 7.1

    When I Isaiah to compile an application in version 7.1 I get the following error.  We saw it before, and if so, what was the fix?  I think to compile mass...

  • Error "requested attribute is not valid.

    I'm looking to get a program (and ultimately define) attributes camera with CVI. I can get the values attribute, such as ROI_WIDTH to the imgGetAttribute function, but not all and not that I really need access, which are 'Exposure time' and 'Gain val