Computer laptop HP ProBook4510s won't turn on after draining the battery

Similar Questions

• Computer laptop Windows 7 won't turn off completely

  6 months ago, I bought a new laptop with windows 7 64 bit installed. has worked well until 2 weeks ago. whenever I stopped, she stays on the screen of closing until the battery is flat. When I turn the back says windows has recovered from an unexpected shutdown. any ideas coz im all that?

  Hello

  Try following the s method provided below and see if it helps:

  Method 1:

  It may be that a third-party application is causing this issue. Put the system at boot. Follow the steps mentioned in the article given below to configure the system to boot and check.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135     

  Note: Once you have finished installing, follow step 7 article to start on normal startup.

  Method 2:

  You can't do a computer that runs Windows 7 stops or sleep

  http://support.Microsoft.com/kb/977307

  Also, try to run the troubleshooter of performance and check if it helps.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-performance-Troubleshooter

  Method 3:

  Also check the event viewer

  Event Viewer is a tool that displays detailed information about important events on your computer.

  http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer

  Hope this helps,

• Computer laptop VAIO suddenly won't turn on - SVF15A1C5E

  Salvation;

  I was using my laptop vaio 3 years fine this morning of battery and closed the cover so that he could go to sleep. Open until this afternoon and it won't start at all! When you press the power button that only the power and charge indicator light, and as long as the button is pressed; as soon as you release the power button, the lights go out. Power goes green and cool goes red.

  If the adapter is plugged in the laptop still does not start, but the charging light is on (red) and stays on. I thought it was fresh off so he left for a bit, but it still won't start.

  Back/bottom of the laptop is sealed/screwed closed and I can't remove the battery to do a full discharge and then try to turn it on.

  The product is SVF15A1C5E

  Serial number is 54624391 0000308

  At this point, any help is appreciated!

  SoC

  There is a reset button at the back of the high tower - a small hole. On my model, that is towards the end close usb and HD connections. Unplug all cables and using a small paper clip, press on into the hole and hold down the button for a second or two. The card, meadows and power cord only. AprΦs the dΘmarrage, taken in the other cables. I'm no expert, but read this a year ago, there is and it worked for me

• iPhone 6 has ran out of battery juice, but won't turn on after connecting the power cable.

  Hello.

  I have an iPhone SIMless 6 (iOS v9.3.2) who missed the battery nothing to juice and turn off the power. I plugged the white USB power cable to a Windows laptop, but nothing happened. No power on, sounds, etc. I even tried another power cable and the source (power supply AC adapter and cable for the iPad). I don't even know if it is supported or not.

  Thank you in advance.

  If it is disabled on its own because of lack of power, it will take some time before he can return to the top.

  Plug it in and leave there for at least 10 to 15 minutes.

• Computer laptop HP G6 does not illuminate. Have removed the battery and the power cable - nothing happens

  Tried removing battery and turn on with power cable - no luck.  The ONLY light anywhere, that's where the cable plugs.  The unit is only 3 weeks old.  Bought at OfficeMax.

  Hello

  If you are still in the period of time where you can return the machine and get it replaced, it's definitely what I would suggest - you shouldn't be troubleshooting a whole new machine and it sounds like a hardware problem.

  Kind regards

  DP - K

• Laptop won't turn on after the new battery.

  A few days ago, when I got home, I found that my VAIO VPCF1290x of 3 years was dead. The battery indicator has been telling me to get a new battery, but I thought it would be enough for now.

  Problem: Laptop wouldn't turn on after pressing the power button.

  (1) with the adapter and the battery still in my laptop, by pressing the power button does not turn on my laptop. However when I press the power button, green light battery (the button itself) indicator on for about a second, then dimmed quickly.

  (2) after reading some forums, I decided to fill my laptop into the battery button for a good 30 seconds trying to turn slot WITH the adapter. It turned on my laptop, but it took a good 2-3 seconds for the laptop to make all sounds as if it was about to start.

  I have since then bought a new battery and a reason that my laptop lights at all. When I connected my new battery to condition it green button energy came on again for about one second then disappeared.

  I don't know what's the matter with my computer and would like to help. I KNOW that I should probably get repaired but would like an idea as to why my laptop behaves like a *.

  EDIT *.

  To give more information, when I have the OLD battery placed in the computer of the battery indicator is a constant flashing orange.

  With the NEW battery sony return the same thing occurs when the battery light constantly blinks orange.

  
  

• Won't turn on after "relocation" on same HD Win7.

  Won't turn on after "relocation" on same HD Win7.

  Same HD (with existing work WIN7) has been used in new construction after that old MB crapped out. It wouldn't boot, so I re-installed Win7.
  It was the 2nd PC on a PC 3 family pack update version.
  The last time that I had a problem with the activation I actually had a phone number to talk to a real person, but now I keep running into dead ends... help! (25 days)

  Have you tried to restart by phone?

  How to activate Windows 7 manually (activate by phone)
   
  1) click Start and in the search for box type: slui.exe 4
   
  (2) press the ENTER"" key.
   
  (3) select your "country" in the list.
   
  (4) choose the option "activate phone".
   
  (5) stay on the phone (do not select/press all options) and wait for a person to help you with the activation.
   
  (6) explain your problem clearly to the support person.
   
  http://support.Microsoft.com/kb/950929/en-us

  Direct activation number: (888) 725-1047

  1-800-936-5700

  However, the requirements for the media upgrade is that you have an operating system already eligible such as Windows XP or Vista installed to use it. Since the Windows 7 end user license agreement.

  15 UPDATES. To use upgrade software, you must first be licensed for the software that is eligible for the upgrade. After the upgrade, this agreement takes the place of the agreement for the software that you upgraded. After upgrade, you can no longer use the software that you upgraded.

  So, if you are always denied, you will just have to reinstall Windows XP or Vista and let it do the verification of eligibility.

• Hello, just set up a new computer laptop and wanted to reinstall CS5 on it. The system is El capitan. When I finished the download and try to install I got a message saying the installation file is damage and saying it s better power eject it. I tried to

  Hello, just set up a new computer laptop and wanted to reinstall CS5 on it. The system is El capitan. When I finished the download and try to install I got a message saying the installation file is damage and saying it s better power eject it. I tried to download several times and in different places. That is wrong. Does´NT CS5 run on El Capitan? Or what else? Thank you.

  CS6 and previous programs have not been tested and will not be updated to run on Mac El Capitan

  -which means you are trying to use CS6 and earlier at YOUR risk of having problems

  -You can get CS6 and previous programs to install and run, or you can not (some do, some don't)

  -Java https://helpx.adobe.com/dreamweaver/kb/dreamweaver-java-se-6-runtime.html can help

  Install CS5 on Mac 10.11 https://forums.adobe.com/thread/2003455 can help (also for others than CS5)

  -also a TEMPORARY security change https://forums.adobe.com/thread/2039319

  -http://mac-how-to.wonderhowto.com/how-to/open-third-party-apps-from-unidentified-developer s-mac-os-x-0158095 /

  -the guardian https://support.apple.com/en-au/HT202491

• My computer is stuck in a boot loop indefinitely after downloading the Vista updates.

  original title: I have the same problem posted by Don Gagen on 16 April. My computer is stuck in a boot loop indefinitely after downloading the Vista updates.

  I installed some updates Vista Home Basic important for my laptop on Wednesday, and since then, my computer won't start. I get to the first page of Windows that shows "Configuration updates 0% complete" for about 15 seconds and then restart the machine. This loop continues indefinitely. I spoke to the manufacturer (Dell) who say there have been some recent problems with the update service, and I have to pay (£69) to address this problem. I don't really want to pay for a repair, when the problem does not seem to have been caused by me or my computer. I tried all the options from the start menu, but there seems to be no way to solve this problem, for example, in 'Safe' Mode, the problem persists, and 'Last successful login' does not work either. It will not launch command prompt. I ran Dell diagnostic check before extended initialization and there seems to be nothing wrong with the hardware. I have no disks system of re - install Vista (and that I would lose all my data anyway). I can also access the ID of the license of Vista. The computer is no longer under warranty, and I have no agreement to support hardware or software for it.

  I would be grateful for any suggestion.

  Alan

  Help us help you: start by reading this post 'sticky '...

  What information to post in the Windows Update forum
      http://answers.Microsoft.com/thread/1467f44b-ee27-4F7D-98d7-f1c4b35b3395

• I use my MacBook Air as a desktop computer. Should I leave the charger plugged all the time or should I drain the battery and then recharge? What is the best for the battery?

  I use my MacBook Air as a desktop computer. Should I leave the charger plugged all the time or should I drain the battery and then recharge? What is the best for the battery?

  Keep the computer plugged in whenever possible.

  If you keep the computer always connected, make sure that at least twice a month

  Run it on battery until battery charge level falls to about 40-50%.

  Please don't completely discharge the battery. Discharge the battery completely will reduce wear and tear on the battery.

  For more information:

  Section: To optimize the battery life

  http://support.Apple.com/en-us/HT204054

  Citing at the bottom of the linked article.

  "The question is often asked:" should I disconnect my laptop from the mains when not in service? Under normal circumstances it should not be necessary because as soon as the lithium-ion battery is full, a properly functioning charger will stop the load and load the pad will only engage when the battery voltage drops to a low level. Most of the users do not remove AC power, and this practice is safe. »

  http://BatteryUniversity.com/learn/article/bu_808c_what_the_user_can_do

• Fact ' slide to power on "drain the battery? / How to turn it off.

  Just, I got my W520 and noticed that the fingerprint sensor has failed in this setting (after I turn off the led is lit green). How fast did it drain the battery? It is an interesting possibility, but at least I can connect to the password of the bios is nothing more than a gimick I can say.

  -FDP

  No need to go into bios. Open "Thinkvantage fingerprint software"-> settings-> authentication (first tab), under the "safety walk", uncheck the "footprint user digital instead of the power button

• Error message "the computer restarted unexpectedly or encountered an unexpected error" after starting the system on Windows 7 Recovery.

  While trying to reinstall Windows 7 on my Dell Inspiron 1545 of the reinstall DVD after you have installed a hard drive again, I got this message: error message "the computer restarted unexpectedly or encountered an unexpected error" after starting the system on Windows 7 Recovery. Tried F10, SHIFT F10 and nothing happened. Then I tried a suggestion of virtual Agent to press F8 to get to advance Boot Options, but this option does not appear! Help!

  For Dell cptrs, you will need to press F12 to access the unique Boot Order Menu(= a temporary setting), little after the Dell logo appears on the desktop. U hv only 5 seconds to do, b4 the cptr will automatically initialize to top with the internal HARD disk.

  ....... F12 is usually used to start the cptr since the DVD player or a plugged in USB-flash drive with a Win 7 install or recovery media.

  To permanently change the boot order, you must similarly press F2 to access the full Boot configuration Menu. The default boot device is the internal HARD drive, but this can be changed to DVD player, USB, disk, network drive, etc. F2 is usually used to start the cptr of an external hard drive(= USB HDD) that contains a bootable Linux operating system.

• Computer won't turn on after the mode 'sleep'

  My computer acted funny lately when it goes into mode 'sleep', and I have to reboot it until I can do something new. I know I'm not the only one having this problem, I've read the other posts on this problem. Anyway, my keyboard has a sleep button that I brush occasionally, that causes all this to happen. However, I brushed it today, and instead to go just in a coma, the computer entered into mode 'sleep' (the light was orange, noise died down), then woke up to the top in a way where the fan on, but the light went off. I've forced to close and then turned back on. Now when I turn it on, the light and fan both going on, but the monitor remains off, and none of the lights on the keyboard lights up. Is there a simple solution to this, or it will need repairs?

  Hello

  Were there any changes (hardware or software) to the computer before the show?

  Perform the steps from the link below.

  The problems of wake the computer from sleep mode

  Warning: Be careful when you change the BIOS settings. The BIOS interface is designed for advanced users, and it is possible to change a setting that can prevent your computer from starting properly. BIOS update should be made only if necessary (to solve a compatibility problem, for example). It can be a complicated process, and if an error occurs, your computer could be rendered inoperative. Be sure to observe the instructions of the manufacturer.

  Reference link provided below for more information:

  BIOS: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/BIOS-frequently-asked-questions

  Hope this information helps.

• Computer won't turn on after a Vista update. How can I fix?

  Yesterday, I tried to install a Vista update.  It was wide enough because the message says that I wouldn't be able to use my computer for about an hour.  I started the process and the left.  4hours later I returned and my computer is waiting for permission to restart to continue the update process.  I rebooted and for a while it seemed to make progress.  Again, I have left for another 3 hours or more, and when I got back to my computer was hibernating and wouldn't wake up.  After trying to wake up in vain for 15 minutes, I made a forced stop.  During its restart in safe mode, I got a message saying that the computer failed to start and suggested a system recovery, who did.  He worked on that when I had to go to work.  Throughout this process, he has been connected with a full battery.  4 hours later I went back to work.  Despite being connected, with the lit sheet icon, my computer was off with the battery low light flashing.  I tried to turn it on.  He showed the black and grey, window prompting me to start in SafeMode or start regularly, before I could choose, the low battery alarm when off the coast and off the computer.  Now, I can't turn on my computer with or without the battery then that plugged or unplugged.  I don't know what the exact date was, just that it's an update to Vista.

  Hello

  It sounds like a hardware error which would happen at the next reboot and is
  probably incidental to the update. You need help from a real computer store (one who
  internal service and not of leeks and display a Best Buy or other stores)
  or support from the system manufacturer.

  I hope this helps.

• iPod 5th generation won't turn on after falling in the bathroom and then dry with rice! What should I do?

  Hello

  My iPod touch 5th generation won't turn after being immersed in water bath for about 15 seconds and then dried to rice. I tried pressing both the House and the buttons but nothing happens! My iPod is about a year and a half and it usually works very well.

  It really scares me because it's the only small portable device I have, which means that if I lose, I'm stuck carrying my iPad autour, which is quite heavy. Also, I wrote something about the iPod that I really like, but I didn't sync it to my computer, as I was traveling while I wrote it and then also when the machine broke.

  This is an urgent matter, because I travel by plane in twelve days and there's a pretty long flight. I want it fixed right here - what can I do?

  Thank you

  Stella

  Hello moxie.star,

  Thanks for this info and choosing the communities Support from Apple. I know how important to get your iPod working again is for you! Based on what you said, it seems you can be affected by a hardware problem and get your iPod repaired by a technician to repair Apple. Please click on this link to find the best option for your situation:

  the Service response to iPod

  See you soon!