Computer shows as connected... but we can not access the internet.

Similar Questions

• My laptop connects is more to the internet, either hard wired or wireless. When it is hard wired, the laptop displays connection but I can't access the internet, and I've done it before.

  My laptop connects is more to the internet, either hard wired or wireless.  When it is hard wired, the laptop displays connection but I can't access the internet, and I've done it before.  My other computer has service very well (or I wouldn't send this message) I checked everything, what to do?

  original title: internet connection.

  Hi vonhatten,

  1. Did you the latest changes on the computer?
  2. You receive an error message when you try to connect to the internet?
  3. You have security software installed on the computer?

  Refer to the article below and try the steps mentioned, check if it helps.

  In Windows network connection issues

  http://support.Microsoft.com/kb/313242

• I have a laptop with Windows XP that show an icon connected to the internet, but I can't access the internet.

  Hello

  I have recently setup a wireless connection from my laptop on Windows 7 works very well. but I have a laptop with windows xp that show an icon connected to the internet, but I can't access the internet can you please help me.
  Thank you
  original title: wireless internet

  Do you receive kb from the internet source or is it local only, and when trying to access the page host does upward with the site not found or 404 error, have you tried to repair the connection, it could be your antivirus protection is blocking the signal.

• When a user logs off Windows 7 x 64 session, the rest can not access the internet until the restart network card

  Hello! I found a problem with my system: when a user logs off Windows 7 x 64 session, the rest can not access the internet, until restarted network card. Reinstall NIC driver did not help. Problem appears on a built-in adapter, in the motherboard and a separate PCI card too.  Same router via its web interface is not accessible. Windows cannot automatically fix this problem after trying to diagnose a problem with his problem Diagnostic tool. After the diagnosis in the DETAILS window, MORE tests, it displays a message like this "computer remote can not receive a connection via the Internet (HTTP) Service Port". "Unplugging" a corresponding Local network connection and then reconnect solves the problem immediately. Switching between users, when two of them are connected do not cause this problem. Important: the problem occurs in the account of the user who was logged on the system FIRST after the PC was on, when the user disconnected on newspapers of a SECOND. If the SECOND user is logged in and the FIRST user disconnects, SECOND can still access the internet. It depends only on the sequence of the user's record, not on the particular user name. And one more interesting fact: after each user registered on and outside just for once, the problem seems to disappear until the PC is turned off and turn it back on!

  System details:

  Motherboard: ASUS P8Z77-VLK
  CPU: Intel Core i7 3770 K
  RAM: 8 GB
  OS: Windows 7 x 64

  Hi, Mahesh,

  and thank you very much for your help! Update firmware driver and router LAN did not help me get rid of my problem, but greatly improved my experience of networking in general. Anti-virus software was not guilty, also, but! I found the "iControl" network software, installed as part of Sogiciel 'AI Suite II' (that came on the CD of motherboard ASUS driverssoftware), runnning and causing not only the problem mentioned above, but would also decrease upload speed up to 0.3 MB/s, when download passes to nearly 100 Mbps! Moreover, searching the Internet, I have found a lot of complaints about the behavior of this software, so that people watch you the occasional installation of this piece... sweet ;) As "iControl network" has been uninstalled (not only turned off in the settings of 'Ai Suite II'!), I'm totally happy with my system performance.

  Best regards
  Greg

• Satellite A110-277: can not access the internet wireless

  Hello
  I have a Toshiba Satellite A110-277. We have wireless internet access in our House and it was workin fine, but since a few days I can not access the internet. My laptop is certainly recognizing internet connection wireless, but through IE or Firefox it just does not connect.

  For some reason, he worked briefly through Firefox, but then that stopped. I don't see what anyone, I have done differently, other than (finally) updated Windows Media Player, but why would that cause problems, I don't know!

  I would really appreciate help as soon as POSSIBLE, that the internet is my lifeline to work!
  Thank you
  GcDh

  Hello

  You said
  > My laptop is no doubt recognize the wireless internet, but does not connect via IE or Firefox, it's just
  Hmm, I guess that you can connect to the WLan router and can insert the WiFi encryption key successfully right I'm right?

  How does LAN connection? Can connect you to the internet using the LAN cable?

  Feedback would be appreciated

• I installed Windows XP but I can't access the internet. I checked the IPconfig and it is empty. The indicator light on the adapter is on green.

  I installed Windows XP but I can't access the internet. I checked the IPconfig and it is empty. The indicator light on the adapter is on green. Of course, the drivers are missing but whom?

  original title: IPConfig and lack of internet access

  Go to your computer manufacturer's support web site
  and search for the Windows XP drivers for your specific computer or motherboard model number.

  If there are Windows XP drivers, then download to a folder on your hard drive and burn it to a CD/DVD.
  Then, after installing XP install all device drivers, starting with the card mother/chipset drivers.
  LAN, Audio, USB, SATA, etc, and so on.

  Note: If there is no XP driver listed, then your computer is not compatible Windows XP.

  List of computer manufacturer support sites:
  http://Windows.Microsoft.com/en-us/Windows/help/contact-support/computer-manufacturers

  If you have an Intel motherboard, you can try the Intel driver update utility: http://www.intel.com/support/detect.htm?iid=dc_iduu

  Graphics/video drivers:
  Check the download site of the manufacture of the graphics card for the newer Windows XP drivers for your card.
  ATI: http://support.amd.com/us/gpudownload/Pages/index.aspx
  NVIDIA: http://www.nvidia.com/Download/index5.aspx?lang=en-us

  =========================  IpConfig ===========================

  Open a command prompt window and type these two commands in the following
  order:
  (1) ipconfig/release
  (2) ipconfig / renew

  J W Stuart: http://www.pagestart.com

• Tecra M5: Can not access the internet pages, but can ping in cmd.exe

  Hi all, this is confusing to me.

  I've been happily connected to my WLAN for more than a year without any problems. I recently updated my drivers for the following on my Tecra M5:

  -Intel Pro Wireless adapt
  -Drivers audio Sigmatel
  -nVidia graphics card

  Now, after facilities, everything was fine. However, a few days later, I turned on the laptop and went to IE7 and it cannot display the web page (my homepage is www.google.co.uk). I called my ISP to help and they reported problems on the service, and they gave me the www.google.co.uk ip address I got a response of in cmd.exe. It seems that I can get out on the internet but I can't access the Web pages - it could be a DNS issue?

  I have disabled my A - V and firewall and tried but get the same question. I also tried to restore the PC back more than a month and it did not help either. I'd appreciate any help that anyone can give.

  I also plugged the laptop directly into the router using an ethernet cable, so it's not only a wireless issue either.

  I have installed any other software at all at the moment and the only other thing that got my attention, it's that, in the field of restoration, there a lot of system restore points, which I wasn't expecting to see in the last month. But it could be a Kipper.

  Thank you very much

  MARC

  Hello

  According to your message, you are not able to connect to internet via LAN and WLan. Is this good?

  Well, in your case I would first check the router settings and re still.
  In addition, you must reset the router.

  Usually, the router assigns the IP address, and therefore you would just plug the laptop LAN cable and then should be able to connect to the internet.
  Please note that the TCP/IP protocol settings must be set to automatic.

  Check everything first!

• Can not access the Internet following couldn't reinstall Vodafone dongle software

  I am running Vista Business Edition. I have a Vodafone dongle for mobile Internet access with my HP laptop. The associated software wouldn't load yesterday. I uninstalled and tried to reinstall it. Impossible to reinstall. Since then I can't access the Internet. I can get on my network wireless but no Internet. I tried to get Vista to fix the problem but the joy. I tried system Restore to four different restore points and none have worked. Suggestions, please?

  Falco,

  'No Mo' is just that this issue could be better addressed by Vodafone. Please check with them to see if they have a solution to your problem:
  http://www.business.Vodafone.com/site/bus/public/enuk/home/p_home.jsp

• VAIO w / Vista connect wireless but I can't access the internet on my router

  Help.  I have a SONY VAIO with Vista.  Just totally reformatted.  I can access my router (NETGEAR WNR 2000v2) locally, but cannot access the internet.  Curiously, I can connect to unsecured networks and access to the internet.  How can I solve the problem with my router/computer? I removed the 3rd party (Norton) security and made a few other commands nothing done. (BTW - I have 3 other devices that work fine on my wireless router.)

  Hi barry909,

  ·         You get the error message?

  Follow the steps in the article.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Reference: http://windows.microsoft.com/en-US/windows-vista/Wireless-networking-frequently-asked-questions

• VPN established but the customer can not access the internet... Need help.

  Hi all

  I'm trying to get a functional ASA 5505 appliance but does not always succeed. I managed to get connected to the ASA VPN client, but once connected, vpn client cannot access the internet. I am trying to route traffic from the client to the VPN server so I don't want to split tunneling. Here is the sketch of the testbed of the network:

  DNS:210.193.2.66
  |
  |
  Inside   ---------  Outside                         ---------          -------------------
  192.168.1.1 |         | 202 *. *. 84 202.*. *. 1.         |          [                  ]
  ---------------------- ASA |-------------------------------------  GW  |----------[ INTERNET ]
  |                   | 5505.                    |                |         |          [                  ]
  |                   | --------|                    |                 ---------           -------------------
  Host_A                                          | 202.*. *. 83
  192.168.1.5                                -------------
  | NetGear |
  | Router |
  --------------
  | 192.168.2.1.
  |
  |
  HOST_B |
  Physical addr:192.168.2.2
  Addr:192.168.3.1 VPN

  The ASA 5505 config is as shown below:

  Output from the command: 'show running-config '.

  : Saved
  :
  ASA Version 8.2 (1)
  !
  ciscoasa hostname
  activate 0cMYKRmmOdVhcSr4 encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP 202.*. *. 84 255.255.255.128
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  passive FTP mode
  inside_nat0_outbound list of allowed ip extended access any 192.168.3.0 255.255.255.224
  pager lines 24
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  IP local pool vpnpool 192.168.3.1 - 192.168.3.20 mask 255.255.255.0
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 202.128.171.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  http 192.168.1.0 255.255.255.128 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  enable client-implementation to date
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  dhcpd outside auto_config
  !
  dhcpd address 192.168.1.5 - 192.168.1.20 inside
  dhcpd dns 210.193.2.66 210.193.2.34 interface inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  Group Policy Reveal internal
  Group Policy attributes Reveal
  Protocol-tunnel-VPN IPSec
  username password alice tnbrh7ICan8mnq/Y encrypted privilege 0
  alice username attributes
  Strategy Group-VPN-Reveal
  tunnel-group Reveal type remote access
  tunnel-group reveal General attributes
  address vpnpool pool
  Group Policy - by default-Reveal
  tunnel-group show ipsec-attributes
  pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:bfb0083a8eb2416e9cc27befe3b224d9
  : end

  a few thoughts

  permit same-security-traffic intra-interface

  NAT (outside) 1 your pool of vpn client

  ASA sysopt connection permit VPN

  ASA sysopt connection permit-ipsec

• can not access the internet even if my wifi connection status is "enabled", I go to another user and am connected, get updates and others and have the ability to nav.

  Windows 32-bit Vista on a HP laptop, wifi is on State is enabled and still on the past of the main user unrelated real, even when the State is supposed to be activated, I went my way, any other user and get the updates to download and other connect ability.  Can someone help me change it's for a 76 year old mother, who gets very nervous sometimes with the laptop that I gave him, help me please... Stevielee

  Hi Stevielee,
   
  1 you get an error message when trying to go online?
  2. what web browser do you use to go online?

  You are able to go online to a different user account. There must be a problem with the settings of the web browser. Try these steps and check the result.

  Step 1: Reset the Internet Explorer settings.
  1. Click Start, type inetcpl.cpl and press to enter.
  2. click on the tab advanced and then click Reset.
  3. click on reset.
  4. When you are finished, click Close, and then click OK.
  5. close Internet Explorer and reopen it before the changes take effect.
  6. check internet connectivity.
   
  NOTE: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.
   
  For more information on "Tips for solving problems with Internet Explorer", visit this link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-Internet-Explorer

  Step 2: If the problem persists after you follow step 1, try to correct the user account.
  Difficulty of a corrupt user profile: http://windows.microsoft.com/en-US/windows-vista/Fix-a-corrupted-user-profile
   
  Try the steps and post back with the results, so that we can help you further.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Internet security problem - I got a security alert was attacking my computer or filtered in and I could not access the internet

  Yes, all of a sudden, I got a security alert was attacking my computer or filtered in and I could not access Internet, I advocate for window / malware scanning and also, mcafee for extra security, but it happens still., why? Then a few days later, I was able to get on the internet again, only about 2 days, now I can no longer access the internet, Iget, open with file, message, so I guess I have to reinstall internet explore, some of my applications are not running, but I think that their always there.  I have scan Windows / Defender and mcafee installed and running on my computer, so what's the problem here?

  Hello

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

• WEBVPN (IOS) can not access the internet

  Hello

  I am to evaluate WEBVPN (SSL VPN) functionality on the router CISCO 1921.

  I can establish a VPN connection with anyconnect and access the intranet local, but I can't access internet.

  I don't know what happened with the packets intended for internet.

  Below, I'll send webvpn configuration:

  GigabitEthernet0/0 is LAN interface

  IP nat inside source static tcp 192.168.100.1 5443 94.140.xx.yy extensible 5443

  WebVPN gateway GATEWAY WEBSSL
  interface IP port GigabitEthernet0/0 5443
  SSL trustpoint TP-self-signed-4050442324
  development
  !
  WebVPN context ASCAL SSLVPN
  secondary-color #990000
  title-color black
  list of authentication SSL - VPN from AAA.
  Gateway GATEWAY WEBSSL
  10 Max-users
  !
  SSL authentication check all
  development
  !
  Group Policy SSLVPN_POLICY
  functions compatible svc
  SVC address pool "vpn_pool" netmask 255.255.255.0
  generate a new key SVC new-tunnel method
  mask-URL
  Group Policy - by default-SSLVPN_POLICY
  !

  Thank you in advance.

  Kind regards,

  Herman

  Hello

  Make sure that you have the list of nat source configured to allow the VPN pool, if you want to use internet from the router or you can use split tunnel to allow only internal traffic on VPN

  example:

  SVC split Router (config-WebVPN-Group) # include 198.168.100.0 255.255.255.0

  SVC split Router (config-WebVPN-Group) # include 192.168.200.0 255.255.255.0

  Kind regards

  Averroès.

• Comments (Ubuntu) can not access the internet through host (XP)

  I used Google to find a solution as to why guest (Ubuntu) cannot access the internet. Host system is Windows XP. None of the solution has not worked for me. Solutions that worked for others: 1 activation NAT 2. Allowing the shared internet connection

  I think the problem is that my host and guest use different subnet masks default (respectively 255.255.0.0 255.255.255.0 vs) assigned by DHCP. The host's configuration manually to use the same subnet mask doesn't help either. I guess that I have it configured incorrectly.

  Welcome to the community,

  I think the problem is that my host and guest use different subnet masks default...

  Your configuration looks like, it has been changed manually! Default vmnet8 (NAT) on the host computer has an IP address like 192.168.x.1/24, comparable to vmnet1 (Host-Only). I suggest that restore you the configuration to its default settings that should work as expected.

  André

• BlackBerry smartphones can not access the Internet using the browser

  Problems tonite to access the Internet using the browser button... get several different messages, the first was:

  ERROR HTTP 500 internal server error... An unexpected condition has occurred...

  then ERROR HTTP 503... server overload

  I can't access using Menu.then by clicking on the bookmarks saved... any ideas anyone?

  Hi and welcome to the forums!

  Open the browser, options, cache operations, delete all categories.

  The go to the configuration of the browser, scroll to the identification of the browser, change Internet explore!

  Battery pull. See how it works.

  KB11266 HTTP 500 error when you use the browser

  Thank you

  Bifocals