Configuration of NIC on ISE 3395

Similar Questions

• Cannot access the ISE-3395-K9 CISCO Web GUI

  Hello

  I can't access the ISE-3395-K9 web gui interface concert 0 with ip address is 192.168.1.10.  I put the ip address of my labtop to 192.168.1.20 and could ping back but am still not able to access them through a direct connection between my labtop to concert interface 0 using one of the supported web browsers.  Any help would be greatly appreciated.

  It is possible that the GUI was configured to restrict access to only certain IPs / subnets. If 192.168.1.x isn't one of them, then you will have access.

  Are you able to connect to the shell via SSH? If so, you should check and confirm that all associated ISE services run by running the following command:

  show the application status ise

  Thank you for evaluating useful messages!

• Can WOL while the port is configured to authenticate through ISE

  Hi all

  I tried setting up WOL

  The L3 switch configuration I have no problem in it

  Configuration of the L2 switch without configuration of ISE

  interface fa0/1

  switchport access vlan 100

  switchport mode access

  spanning tree portfast

  It works well, but after that I put the ISE configuration on the port, WOL is not working.

  so please help can I use ISE + WOL or there will be problems because of that.

  I read a custom ' authentication control direction in "which should enable ISE and WOL.

  then, which will affect on something.

  Thank you.

  Yes, that's correct. If you add the command "authentication control-direction in" on a switchport then he will allow the "Magic Packet" WoL should be sent to the unit of the end and wake him up.

  By default, a switchport configured to dot1x will only allow EAP traffic initially to the switchport (thereby breaking WoL) you don't need to add the command "authentication control-direction in" to allow WoL functionality to continue working while ensuring that the endpoint can still only send EAP frames to the switchport prior authentication of 802. 1 x.

• Configure 2 NICs for a virtual machine

  Hello

  How can I connect two physical network interface cards in a virtual machine?

  Each NIC is configured on a separate network - but on the same machine.

  is it possible...

  Thank you

  Hello

  Just create 2 vSwitches on the host, allocate the host's physical network cards to the separate vSwitches, then create the Group of ports by vSwitch, in the comments adds another nic and assign it to the Group of ports that you need.

• Configuration of NIC in the cloned VM

  With the help of Workstation 8.0.1 build-528992, I created a basic Linux 6.2 CentOS VM guest in network bridge. This setting is configured as my model VM I use to create virtual machines other, specialized.

  I then cloned this virtual machine as a full clone, without link. Before you start the virtual machine, I clicked on the network card. Advanced... button and generated a new MAC address.

  After starting the virtual machine cloned, I ran ifconfig and got this:

  eth2 encap HWaddr 00:50:56:26:0 A Link: 3F
  INET addr:192.168.2.118 Bcast:192.168.2.255 mask: 255.255.255.0
  ADR inet6: fe80::250:56ff:fe26:a3f / 64 Scope: link
  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1
  Fall of RX packets: 423 errors: 0:0 overruns: 0 frame: 0
  Dropped packets: 112 TX errors: 0:0 overruns: 0 carrier: 0
  collisions: 0 txqueuelen:1000
  RX bytes: 54736 (53.4 KiB) TX bytes: 11955 (11,6 KiB)

  Lo encap:Local Loopback link
  INET addr:127.0.0.1 mask: 255.0.0.0
  ADR inet6:: 1/128 Scope: host
  RACE of LOOPING 16436 Metric: 1
  Fall of RX packets: 18 errors: 0:0 overruns: 0 frame: 0
  Dropped TX packets: 18 errors: 0:0 overruns: 0 carrier: 0
  collisions: 0 txqueuelen:1000
  RX bytes: 1548 (1.5 KiB) TX bytes: 1548 (1.5 KiB)

  The eth2 listen to me, so run this: ls/etc/sysconfig/networking/devices. He told me that I have a NETWORK card device, ifcfg-eth0.

  Then, I ran system-config-network and chose the Configuration of the device. Again, it has reported only eth0 was available.

  Recalling that I saw before eth2, I thought that perhaps that eth0 has not been started. So I issued a command ifconfig eth0 up . It reported unknown interface: no such device.

  So my questions are:

  (1) where did he eth2?

  (2) where eth0 is?

  (3) how can I fix this so that the one and only one NIC is eth0?

  Thank you.

  --

  Jack

  It is in fact the re-creation of the MAC address, which is regarded as a new NETWORK card, and therefore a new interface.

  You can either edit the file and remove the external devices, or you should also be able to remove this file completely (to move somewhere else to play it safe) and restart.

  -KjB

• Configuration of NIC for ESXi 4.1

  Happy to wander what others do for their NETWORK card for ESXi 4.1 configuration I want to use the following:

  pNIC0-> vSwitch0-> Portgroup0 (management)

  pNIC1-> vSwitch0-> Portgroup1 (VMotion)

  pNIC2-> vSwitch1-> Portgroup2 (the VM network)

  pNIC3-> vSwitch1-> Portgroup2 (the VM network)

  pNIC4-> vSwitch2-> Portgroup3 (DMZ network)

  pNIC5-> vSwitch2-> Portgroup3 (DMZ network)

  I don't have that much wandering DMZ traffic so if I should use one of the DMZ NIC for VMotion or management.

  Mike

  According to me, it looks good, you have redundancy built in.  The only thing that we do, and maybe you do the same thing is on our vSwitch0 active/standby network interface cards to each other.  The other vSwitches are set to active/active.

• configure multiple NICs

  Hello

  I have ESX server configured with SERVER-based storage.

  I have a card of 1 GB on each server.

  I bought 2:

  NIC HP NC7170 PCI - X Gigabit double

  Now I have an option to add 1 dual port card to each server.

  So I have 3 on each server gigabit ports.

  What will be the right way for the configuration.

  I'd appreciate links or explanation on this topic.

  THX.

  Hello

  Check out my blogs of topology to http://www.astroarch.com/wiki/index.php/Blog_Roll#Cisco_Subnet_-_Blue_Gears_-_Virtual_Networking specifically Blue Gears - 3 with VMware ESX physical NIC.

  Best regards

  Edward L. Haletky

  VMware communities user moderator

  ====

  Author of the book "VMWare ESX Server in the enterprise: planning and securing virtualization servers, Copyright 2008 Pearson Education.»

  Blue gears and SearchVMware Pro Articles: http://www.astroarch.com/wiki/index.php/Blog_Roll

  Security Virtualization top of page links: http://www.astroarch.com/wiki/index.php/Top_Virtualization_Security_Links

• To get on the internet I have to re - configure the NIC or restart the system

  To get on the internet I have to re - configure the network card or restart the system. My os is Vista 32 bit. How can I fix this so I can do things on the internet.

  I use Internet Explorer 9

  Hello

  You may need to update the network card with the latest drivers from the manufacturer's website.

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  See: http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-network-adapter-problems

• NAC agent and configuration of NHPS with ISE 1.1.1

  I try to get all the workstations (OSX and Windows) install the begging native NAC Agent and Assistant during the on-board process.

  I currently use portal default comments to EHT.

  The environment has been implemented using a design of dual SSID.

  For the moment, devices can plug the SSID of provisioning and get the CWA. Recording device works, the portal is running the installer of NHPS that correctly implements the network card.

  The problem is that the portal never tries to install the NAC Agent.

  Has a political client provisioning policies for wired and wireless as well as BONES. Each strategy includes a PSN and Agent NAC configuration. It seems that portal comments only checks the configuration of PSN and not the NAC Agent config.

  Any ideas?

  Just if I understand correctly, you are using both a client provisioning portal and a native Portal begging provisoning related policies separate authz.

  With that road you check to see if the customer is consistent in the political portal provisioning client.

  Let me know if you have following configured (windows OS in the example), this implies that endpoint is statically assigned to RegisteredDevices after native pursueth provisioning.

  Rule 0 (Group of endpoint = RegisteredDevice) AND (AD:Domain user and authentication method: x 509 and posturestatus: COMPATIBLE) = access allowed

  Rule 1 (Group of endpoint = RegisteredDevice) AND (AD:domain user authentication method: x 509 [If you have deployed the certs to the State native supp] AND workstation NOT EQUAL: COMPLIANT) client provisioning RESULT portal.

  Rule 2 (endpoint = Workstation group) AND RESULTS (AD:Domain user AND breed authentication using mschapv2) provisioning windows portal

  Hope that helps,

  Tarik Admani
  * Please note the useful messages *.

• How can I configure my NICs on my 5.1 esxi?

  Hello

  Why my 3 network cards appear as "used by: vswitch" I would like to configure the static Ip address.

  
  

  
  

  Why do you want to configure an IP address for the vmnic? You need an IP address for the Group of ports management network as well as for virtual machines (which is configured in the guest operating system).

  André

• Configure the NIC NAT on linux-vms

  Hello

  If I convert a vSphere ESX from Vmware Workstation linux vm and set the nic to "nat", that it is not changed in the vmx-file destination, he is always satisfied. Desktop virtual windows it works fine.

  Could it be corrected in the final version?

  See you soon

  Lukas

  Hello

  Tried with Solaris 10 64 bit - it returns to NAT.

  What version of ESX (and what if used VC) are your source on?

  You can send me this task logs, there might be some clue in there.

  The conversion of Windows 2003 was fine, right?

  Regarding regular weekly export - you can do this by using Converter SDK to create a script or a program that invokes a separate Scheduler.

  HTH
  Plamen

• How to configure a NIC connection for iSCSI

  I have a few 2950 s PowerEdge with four NICs in them, trying to use the NIC bonding on 3 of them for iSCSI.

  Are there articles or KB links explaining how to do (if it is possible?)

  Or, just point me to the right section in the vSphere client and I can understand... I have just found nothing of poking around, I wonder if it's just not possible?

  Hello

  The best answer here is that consolidation of NICs for iSCSI traffic is not supported and the various guides on the paths where you should look.

• ISE 1.2 SNS - 3415 NIC bonding / grouping

  Hello

  I installed the SNS-3415 with ISE 1.2 and I try to configure the nic redundnacy (team) modes for requests for authentication and not for the purpose of management.

  Tests have shown that when an interface has been disconnected all was lost and nobody of our internal users was authenticated by the node of the ISE.

  However when I unplugged the "second interface" (possibly inactive) nothing has happened which shows which is a useless interface

  My goal is to connect it to my twins basic switches and have a deployment of high availability.

  -J' have enough search the Web but I have not found any clear and precisely the document to say how this could be done.

  http://www.Cisco.com/c/en/us/TD/docs/net_mgmt/cisco_secure_access_contro...

  THEMIS

  ISE 1.2 does not support grouping NETWORK adapters.  Especially on the devices.  There is a solution for the virtual machine using the ESXi host teaming network adapters so that it is transparent for the virtual machine.

  Please rate useful messages and mark this question as answered if, in fact, does that answer your question.  Otherwise, feel free to post additional questions.

  Charles Moreton

• The ISE Cisco switch configuration

  Hi experts,

  I got the following network:

  Devices-> switch access-->--> access switch central office switch-> ISE Server

  All switches are capable IOS for the 802. 1 X and configurations of AAA for ISE to manage network devices. However, I read in the guide on the configuration of the switches in preparation for the deployment of the ISE of CIsco, but I wonder what should I configure switches for access and basic switches or only configure the switches for access to EHT?

  Thanks for your time to read!

  If all clients are non-DHCP clients, then no configuration is based or distribution at all.

  But you may need to search different options of profiling, if the customers are not active DHCP. Access switch supports the function of detection IOS? Would be very useful to have such a that it would send important profiling information at ISE. You may need to use the right options for ISE of profiling to determine the details of the endpoint.

  Concerning

  Vivek

• Problems of configuration of the NIC in ESXi 4.1

  I have a HP DL380 G7

  I loaded ESXi, the server has 6 physical NIC, 4 on board and 2 in a PCI Intel card.

  The system will accommodate 3 VM - all 2008 R2 Enterprise

  2 servers, I want the team to failover and load balancing

  I have configured my NIC this way

  NIC 0 dedicated to managing the virtual computer

  1 NETWORK card dedicated to a single server running as a domain controller

  Map NETWORK 2 and 5 I want the team to failover and a faster flow on a TS

  NIC 3 and 4 I want the team to failover and a faster flow SQL database running

  I segragated 2 NICd dual servers have a NETWORK card on each card, where a map should fail

  Here's where I lose myself-

  How can I add network cards to the actual virtual machines correctly?

  If the network adapters are associated, I see 1 NIC in each virtual computer or will I see 3 NICs in the actual virtual machine?

  If a virtual computer uses a bundled pair of network adapters, I should add the two network adapters, the settings of the virtual machine?

  If a virtual machine uses a pair of network cards grouped and I see 2 network cards in the actual virtual machine, I need to assign an IP address to each NIC?

  Sorry for so many questions, I'm just getting confused by properly installing network cards.

  I've included a screenshot of what I'm trying to accomplish.

  Vmnic0 is 1 Gbit/s and the others are at 100 Mbps.  Using 2 different physical switches?

  If so, I would put all 3 VMs on vSwitch1.  When you create each virtual machine you can assign just a single vmnic to it.  Then bind the vmnic for the VM port to vSwitch1 Group (which is called Terminal Server now).   Virtual machines will not be limited to 100 Mbps when communicating with each other.