Configuration of static translation "inverted".

Similar Questions

• Static translation PIX

  Just a quick question I have if I'd put on the table. I have a Pix 515, with a total of four DMZ. I had to configure static mappings in the DMZ for some servers. Here's my question. There are three types of static translations:

  High and low note see security levels.

  1. static (high, low) high low

  2. static (high, low) high high

  3. ????

  What is the third static confgiuration and that it would be used for.

  Thanks in advance

  Like this?

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_63/cmdref/s.htm#1026694

  Happy, we could help.

  Scott

• Maximum static translations

  Hi all

  I have a 520 PIX with 16 MB of flash and 128 MB of ram. No one knows what the maximum number of static translations, you can have in the configuration. I would like to translate staticly class B around just for outgoing traffic.

  Thank you

  Steve

  Hello

  The amount of static translation depends on the size of the RAM that you encounter. each translation to 128 bytes of memeory... maybe it is useful for your

  calculating...

  Concerning

  Pauline

• How do I configure a static ip address in windows PE (for windows 7)?

  How do I configure a static ip address with subnet mask and default gateway in windows PE (for windows 7)?

  Probably in the same way as in Windows 7: Control Panel / network connections / network card / properties. If you need a more detailed explanation, it would be best to ask your question in a forum of Windows PE.

• Cannot configure the static IP address for Cisco Touch 8 "

  Hi all

  I found that I can not configure the static IP address for Cisco Touch on TC7.0.1 / 7.0.2 with the procedure described below.

  1. upgrade a codec (e.g. SX20 TC6.3 or less) and a touch paired with the codec for TC7.0.2.

  2. after the upgrade, désapparier (with the help of désapparier Touch button) touch and it reboot.

  3. tap on "IP settings."

  4. Select "Manual IP allocation".

  5. Enter the IP address, subnet mask, default gateway, and then press "Save".

  Even though we have configured the static IP address with the above procedure, IP allocation remains 'Auto' (= DHCP) and the IP address, subnet mask, default gateway is also empty.

  In this situation, the only way to configure the IP address for the Touch is to use the DHCP server.

  I guess many users uses the static IP assignment like us, so please fix it as soon as POSSIBLE.

  Best regards

  Kotaro Hashimoto

  Hi Kotaro,

  It is a known problem in TC7.0.1 and TC7.0.2. The id of the bug is CSCum82147.

  To work around the problem, set IP address you want the button before moving on to TC7.0.x.

  The bug has been fixed and will be included in the next version of the TC software.

  Kind regards

  Jonas Tysso

• Static translation with Port forwarding

  Hello

  I have a scenario in which two public ip address (the one with HTTP requests & other with query SMTP/SSL for OWA) must be translated on a single inside the ip of the ISA Server in the DMZ. Please suggest which is the best practice. I know that we cannot do a NAT because the two addresses ip cannot translate into one. Use the static translation with forwarding Port of best practice to access the ISA server for OWA? What is the best security that can be applied at the moment? I'm going to redirect only requests to port 80,8080,25,443,110. I'll also create access list to only allow as these ports.

  I need to recommend this to a client. Please advice.

  Thank you

  Kevin

  Port forwarding is the best way to go here. As you already know, you can enter a static for two outside IP pointing to an inside (or vice versa), but statically mapping ports just will be fine. Similarly, simply allow these ports in your incoming ACL and you'll be good to go.

  You want something like the following:

  static (inside, outside) tcp XXX1 80 a.a.a.1 80

  static (inside, outside) XXX1 8080 a.a.a.1 8080 tcp

  static (inside, outside) tcp x.x.x.2 25 a.a.a.1 25

  static (inside, outside) tcp x.x.x.2 110 a.a.a.1 110

  public static x.x.x.2 a.a.a.1 443 tcp (indoor, outdoor) 443

  list of allowed inbound tcp access any host XXX1 eq 80

  list of allowed inbound tcp access any host XXX1 eq 8080

  list of allowed inbound tcp access any eq 25 x.x.x.2 host

  list of allowed inbound tcp access any host x.x.x.2 eq 110

  list of allowed inbound tcp access any host x.x.x.2 eq 443

  Access-group interface incoming outside

  where x.x.x. [1 | 2] is your public IP address and a.a.a.1 your home server.

• SE "There are problems with the configuration of static files in your environment" after the APEX 5 install using Oracle HTTP Server

  There is not much information in the doc around the new configuration of static file.  Someone at - it an example of this dads.conf he file should look similar to static files?  Everything else seems to work fine - it's my only hang up now.

  Thank you!

  Exact pop-up message:

  There are problems with the configuration of static files in your environment.  Please see the section "Configuration static file Support" in the Guide of the Installation Application Express

  I figured it out on my own - the doc has a section "6.5.4 configuration Support for static file" which basically said yes, it is now supported for static files, then a "see also:" link to the dads.conf section, that I'm not good enough to see there are now 2 new parameters in your dads config file...  All is ready!  It works!  YAY!

• vSphere 5.5 kickstart to configure the static IP address

  Hello people,

  I spent some time trying an involuntary installation works correctly and adding features I want.

  Right now I'm trying to run a command after installation and reset to configure a static ip address for the host.

  I can say that the configuration file is the application, but does not have the IP address.  Value DHCP when you are finished.

  My KS.cfg file, can someone tell what I do wrong?

  Thank you, romatlo

  # Example scripted installation file

  #

  # Accept the VMWare end user license agreement

  vmaccepteula

  # Set the root for the mode DCUI and Technical Support password

  rootpw tet_password1

  # The installation media is in the CD drive

  install firstdisk - overwritevmfs

  # Define the DHCP network on the first network adapter

  network - bootproto = dhcp - device = vmnic0 - addvmportgroup = 0

  reset

  firstboot % - interpreter = busybox

  # Assign an IP address to the first VMkernel, used for the management

  esxcli ip network interface ipv4 set - name = vmk0-= ipv4 interface 192.168.32.15 - mask = 255.255.255.0 - Gateway = 192.168.32.1 - type static = subnet

  Memory, don't you must first create a VMkernel interface?

  -name of the interface:-i The name of the VMkernel network interface to the IPv4 settings. This name must be an interface in the interface list command.

  VSphere Documentation Centre

  Ensure that vmk0 is listed when you run

  list of network ip interface

  In addition, what happens if you install ESXi manually and run this?

  # Assign an IP address to the first VMkernel, used for the management

  esxcli ip network interface ipv4 set - name = vmk0-= ipv4 interface 192.168.32.15 - mask = 255.255.255.0 - Gateway = 192.168.32.1 - type static = subnet

  FYI in my KS.cfg I have this

  network - bootproto = - 192.168.250.21 = static ip - gateway = 192.168.250.1 - nameserver = 192.168.250.6 - subnet mask = 255.255.255.0 - hostname = esxi5---.lab.local head = vmnic0 - addvmportgroup = 0

  Instead of

  network - bootproto = dhcp - device = vmnic0 - addvmportgroup = 0

  and

  esxcli ip network interface ipv4 set - name = vmk0-= ipv4 interface 192.168.32.15 - mask = 255.255.255.0 - Gateway = 192.168.32.1 - type static = subnet

• How can I configure a static IP address in Windows Server 2008?

  original title: set static IP of Server 2008

  I have a Server 2008 R2 from a CD of demo loaded on a Dell computer.
  When I start my Poweredge 1950 server, I get these messages:
  ' F/W initialization devices 0% '.
  info on the RAID drivers
  "(HA-0 9Bus 2 Dev 14) PERC 5 / i integrated 5.0.1 - 0030"
  "The battery material is missing...". »
  "Source 1 or logical drives on the adapter to the host.
  Logic of 1 drive (s) handled by BIOS
  some information about the remote access configuration utility
  and then he told me that the IP subnet, gateway, are all 0.0.0.0

  I have to hit F1 to continue the boot or F2 to run the Setup utility.

  In the configuration under embedded devices utility, two network cards have TOE activated ability
  I don't seem to be able to assign the NETWORK adapter a static address, and he poses problem when I try to put in place AD DS services
  Server 2003, I read that the TOE function on the NETWORK card is loaded.  I can't disable in the BIOS screen.  I see solutions for
  This manipulation for Server 2003, but nothing for 2008.

  When I try to use installation of AD DS services in advanced mode and get to the screen to select additional options for this domain controller, and I check the DNS of the server, a warning is displayed saying that one or more physical network adapters don't have a static IP address.

  Any suggestions on how to set the static NIC card?

  Thank you

  Post in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• configuration error static equivalent e3200

  My ISP requires static configuration.  I plugged in the numbers and trying to save get a message from the 192.168.1.1 page "value cannot be equal.  What does that mean?  The ip address of my router is the same as the default gateway.  I'm naïve, any help?

  Thanks for the reply.  I changed the ip of the router 192.168.2.1 and he accepted after a full reboot of the pc, modem, router.  Now configure the network.

• Configure routes static ip on CS ACS - SE

  Hello!

  We use a Cisco Secure ACS Solution engine turns V4.2.0.124.3.

  The device have two Ethernet Ports.

  -We need to know how to configure an IP address on the second port. But more:

  -We need to know how to configure static IP routes on this unit.

  Everyone is here to tell us how to do it?

  Regards, Markus

  Markus,

  GBA, you can only use a NETWORK card, and there is no way you can define static routes on it.

  Your system of 1113 Cisco integrated 10/100/1000 megabits - per second (Mbps) Ethernet connectors. ACS SE takes care of the operation of an Ethernet connector, but not the two connectors. Each Ethernet connector provides all the features of a network expansion card and supports 10BASE-T, 100BASE-TX and 1000BASE-TX Ethernet standards.

  Each NETWORK adapter is configured to automatically detect the speed and duplex mode of the network.

  Kind regards

  ~ JG

  Note the useful messages

• DNS and static translations

  I have a web server on my dmz. On the demilitarized zone, the computers cannot be accessed by name. The problem is that DNS returns the ip (real) outside. I need the demilitarized zone to translate it into a local ip address. I use the MDP so I'm not using aliases. Any help would be appreciated.

  You can do this with the [static] commands and the "dns" option

  static (dmz, outside) 123.123.123.123 192.168.1.1 dns netmask 255.255.255.255 [keyword dns tells the pix to DNS doctoring for this translation because DNS resolves the public IP address]

  static (dmz, inside) 123.123.123.123 192.168.1.1 subnet 255.255.255.255 mask [allows the internal hosts to connect to the public IP found in DNS and it translates the private IP on the way to the demilitarized zone]

  Make sure you do a [clear xlate] after the changes.

  If you are running under 6.2, you will have to make any [alias] on the Pix.

• RVS4000 - translation of static hosts

  When you configure a static host translation?  Let's say (for example) the public address is 64.233.169.147 and I need to map to 192.168.1.150 where I put it?  I can then set the firewall rules to allow specific inbound traffic?  Help, please!

  1-to-1 NAT is not supported on RVS4000. Other small business RVL200 and RV042 routers are supported 1-to-1 NAT.

• Configuration of the devices on the same subnet to have a static IP address

  Hello. First of all, I'm new here, so Hello to everyone. I'm pretty much a newbie on everything about routers and I would like an answer to a problem that has been bothering me for a while.

  I have a Linksys WAG120N Wireless - N ADSL2 + Modem Router. The firmware version is V1.00.12.

  I run a Windows machine that is attached to the router which has a certain subnet address. On this same machine, I run a Virtual Machine on Linux, which has its own address, 192.168.1.102.

  I noticed that whenever I have shut down the computer and then reactivate them later, they gain another address, which makes it annoying for me to communicate with each other (by, for example, try to load a Web page hosted on the physical machine virtual computer) without knowing the real address, which, as I said earlier, seems to change every time.

  I would like to know if there is a way (with my model of router) to configure so that address subnet of these two machines remains the same, regardless of whether or not they have been stopped and restarted.

  Is this possible? If Yes, could you please tell me where to find this option in the control panel?

  Have you set the DNS server? You must configure at least one DNS server. Configure as DNS server 192.168.1.1 on your computer.

  Otherwise, with DHCP enabled, open a command prompt window and type "ipconfig/all". Copy the full output in your next post.

  Then configure the static IP address, check if you have the internet, otherwise, run "ipconfig/all" again and also after the full release. Which should show the problem.

• PIX 515 (7.02) and the translation of static port

  Just try to transfer a foreign port int-> device sitting on 'inside' Interface, but do what following in the logs:

  % 106006-2-PIX: Deny UDP incoming from 66.21.215.238/50507 to client_routable_address/6881 on the interface outside

  % 106006-2-PIX: Deny UDP incoming from 62.141.54.206/6881 to client_routable_address/6881 on the interface outside

  % 106006-2-PIX: Deny UDP incoming from 84.217.31.157/6881 to client_routable_address/6881 on the interface outside

  The Config:

  access-list 101 extended permit icmp any any echo response

  access-list 101 extended permit icmp any any source-quench

  access-list 101 extended allow all unreachable icmp

  access-list 101 extended permit icmp any one time exceed

  access-list 101 extended permit tcp any host client_routable_address eq 6881

  access-list 101 extended permit udp any host client_routable_address eq 6881

  Global (outside) 3 client_routable_address

  NAT (BCM) 3 0.0.0.0 0.0.0.0

  static (BCM, outside) 192.168.20.10 tcp 6881 6881 netmask 255.255.255.255 client_routable_address

  static (BCM, outside) udp 192.168.20.10 6881 6881 netmask 255.255.255.255 client_routable_address

  Access-group 101 in external interface

  Static translations are there at the "show xlate:

  # sh xlate

  50 in use, most used 957

  Client_routable_address (6881) Local 192.168.20.10 (6881) Global PAT

  Client_routable_address (6881) Local 192.168.20.10 (6881) Global PAT

  ACL 101 "6881" entries are not to get hit if:

  # See the access list 101

  access list 101; 7 elements

  allowed for line 101 1 extended icmp access list any entire echo response (hitcnt = 0)

  line of the access list 101 permit extended 2 icmp any any source-quench (hitcnt = 10)

  extended all licences for line 101 3 access list all unreachable icmp (hitcnt = 10279)

  line 4 extended access list 101 allow icmp all a time exceeded (hitcnt = 265)

  allowed for line of the access list 101 5 scope tcp any host client_routable_address eq 6881 (hitcnt = 0)

  allowed for line in the list of 101 6 extended access udp any host client_routable_address eq 6881 (hitcnt = 0)

  Am I missing something obvious?

  Hello

  I think you've got your STATIC reversed lines, they must be:

  static (BCM, external) client_routable_address tcp 6881 192.168.20.10 6881 netmask 255.255.255.255

  Assuming that 'client_routable_address' is your public IP and the BMC is your 'inside' or the 'DMZ' interface

  Salem.