Configure routes static ip on CS ACS - SE

Similar Questions

• Network configuration / routing / two network interface cards / NAT - leased / dedicated Dell R210 running VMware ESXi 5.1.0 build-799733

  Network configuration / routing / two network interface cards / NAT - leased / dedicated Dell R210 running VMware ESXi 5.1.0 build-799733

  Hello

  I'm trying to understand how to configure a dedicated server of Dell R210 rented running VMware ESXi 5.1.0 build-799733

  This dedicated server is rented www.online.net and sits somewhere in France. One of its network adapters have an IP public 62.210.177.20x. The other NIC is here, but I do not understand how it is configured. According to the www.online.net portal, the other NETWORK card has or should have an IP 10.90.116.20x. And I am obviously set up is to have some virtual machines running and be able to access the Internet. I have access to the console of the server Dell through iDRAC and since I could see, one of the network adapters in the IP is 62.210.177.20x defined, and the other has been shown out of service. I managed to make it appear the other interface but I cannot find anywhere how to assign the IP address 10.90.116.20x to this 2^nd network adapter. But then again I don't even know if I should or if I need to assing a IP address to this 2^nd network adapter. What is the cable connected even for this 2^nd NIC? I do not know. Should it be - I'm not either. I don't know French and manuals/instructions on www.online.net are in French. I can try an online translator, but I don't think that what I'm looking for is explained. How do I get this set up? I have to do something about the ESXi on the server console? This interface 2^nd should be in place, or it must be down as if it was originally? Yesterday after watching someone videos on YouTube, I added the second virtual switch and moved the virtual hosts of this switch 2 and he entrusted the 2^nd NIC. But that 2^nd NIC had a red X next to it probably indicating that it was disconnected the 2^nd form virtual switch. Today and now I have managed to access the ESXi console server through iDRAC, I bring the 2^nd NIC, and now both network adapters are assigned to the virtual switch 1^st . But I think that a NIC should be attributed to a single switch and the other card NETWORK on the 2^nd switch. I'm just a desktop guy with enough knowledge to be dangerous J if you / someone put in steps how and where to set them up it... PLEASE

  Thanks in advance

  cweks

  ~ # vmware - v

  VMware ESXi 5.1.0 build-799733

  ~ # esxcfg - road

  VMkernel default gateway is 62.210.177.1

  ~ # esxcfg-vmknic-list

  Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type

  vmk0 management network IPv4 62.210.177.20x 255.255.255.0 62.210.177.255 d4:ae:52:cb:bb:84 1500 65535 true STATIC

  vmk0 networking fe80::d6ae:52ff:xxxx:bb84 64 d4:ae:52:cb:bb:84 1500 65535 true IPv6 STATIC, PREFERRED

  Portal www.online.NET--information

  NORMAL 1 ready 62.210.177.20x xxx.domain.eu.       D4:AE:52:AB:BB:84

  2 PRIVATE loan 10.90.116.20x d4:ae:52:ab:bb:85

  http://wiki.hetzner.de/index.php/VMware_ESXi/en#Network_configuration

  Network configuration

  • VMware vSphere Hypervisor is an "operating system" for pure virtualization and support NAT or routing. Therefore, only a real bridge configuration can be used.
  • To use a subnet additional IP must be configured as a router VM.

  If I understand the above, I need to show some VM and set up as a router? If the virtual machine that will act as a router must have two network interfaces, where it is connected to a switch and the other to the other switch network card. Am I do? The YouTube video that suggested, but I thought that maybe / somehow ESXi can route packets between the two network cards, but from what I read, ESXi can route packets. Do I need to order an additional / extra / 2nd IPv4 address so that it can be assigned to the interface of the router?

• How do I configure a static ip address in windows PE (for windows 7)?

  How do I configure a static ip address with subnet mask and default gateway in windows PE (for windows 7)?

  Probably in the same way as in Windows 7: Control Panel / network connections / network card / properties. If you need a more detailed explanation, it would be best to ask your question in a forum of Windows PE.

• Cannot configure the static IP address for Cisco Touch 8 "

  Hi all

  I found that I can not configure the static IP address for Cisco Touch on TC7.0.1 / 7.0.2 with the procedure described below.

  1. upgrade a codec (e.g. SX20 TC6.3 or less) and a touch paired with the codec for TC7.0.2.

  2. after the upgrade, désapparier (with the help of désapparier Touch button) touch and it reboot.

  3. tap on "IP settings."

  4. Select "Manual IP allocation".

  5. Enter the IP address, subnet mask, default gateway, and then press "Save".

  Even though we have configured the static IP address with the above procedure, IP allocation remains 'Auto' (= DHCP) and the IP address, subnet mask, default gateway is also empty.

  In this situation, the only way to configure the IP address for the Touch is to use the DHCP server.

  I guess many users uses the static IP assignment like us, so please fix it as soon as POSSIBLE.

  Best regards

  Kotaro Hashimoto

  Hi Kotaro,

  It is a known problem in TC7.0.1 and TC7.0.2. The id of the bug is CSCum82147.

  To work around the problem, set IP address you want the button before moving on to TC7.0.x.

  The bug has been fixed and will be included in the next version of the TC software.

  Kind regards

  Jonas Tysso

• SE "There are problems with the configuration of static files in your environment" after the APEX 5 install using Oracle HTTP Server

  There is not much information in the doc around the new configuration of static file.  Someone at - it an example of this dads.conf he file should look similar to static files?  Everything else seems to work fine - it's my only hang up now.

  Thank you!

  Exact pop-up message:

  There are problems with the configuration of static files in your environment.  Please see the section "Configuration static file Support" in the Guide of the Installation Application Express

  I figured it out on my own - the doc has a section "6.5.4 configuration Support for static file" which basically said yes, it is now supported for static files, then a "see also:" link to the dads.conf section, that I'm not good enough to see there are now 2 new parameters in your dads config file...  All is ready!  It works!  YAY!

• vSphere 5.5 kickstart to configure the static IP address

  Hello people,

  I spent some time trying an involuntary installation works correctly and adding features I want.

  Right now I'm trying to run a command after installation and reset to configure a static ip address for the host.

  I can say that the configuration file is the application, but does not have the IP address.  Value DHCP when you are finished.

  My KS.cfg file, can someone tell what I do wrong?

  Thank you, romatlo

  # Example scripted installation file

  #

  # Accept the VMWare end user license agreement

  vmaccepteula

  # Set the root for the mode DCUI and Technical Support password

  rootpw tet_password1

  # The installation media is in the CD drive

  install firstdisk - overwritevmfs

  # Define the DHCP network on the first network adapter

  network - bootproto = dhcp - device = vmnic0 - addvmportgroup = 0

  reset

  firstboot % - interpreter = busybox

  # Assign an IP address to the first VMkernel, used for the management

  esxcli ip network interface ipv4 set - name = vmk0-= ipv4 interface 192.168.32.15 - mask = 255.255.255.0 - Gateway = 192.168.32.1 - type static = subnet

  Memory, don't you must first create a VMkernel interface?

  -name of the interface:-i The name of the VMkernel network interface to the IPv4 settings. This name must be an interface in the interface list command.

  VSphere Documentation Centre

  Ensure that vmk0 is listed when you run

  list of network ip interface

  In addition, what happens if you install ESXi manually and run this?

  # Assign an IP address to the first VMkernel, used for the management

  esxcli ip network interface ipv4 set - name = vmk0-= ipv4 interface 192.168.32.15 - mask = 255.255.255.0 - Gateway = 192.168.32.1 - type static = subnet

  FYI in my KS.cfg I have this

  network - bootproto = - 192.168.250.21 = static ip - gateway = 192.168.250.1 - nameserver = 192.168.250.6 - subnet mask = 255.255.255.0 - hostname = esxi5---.lab.local head = vmnic0 - addvmportgroup = 0

  Instead of

  network - bootproto = dhcp - device = vmnic0 - addvmportgroup = 0

  and

  esxcli ip network interface ipv4 set - name = vmk0-= ipv4 interface 192.168.32.15 - mask = 255.255.255.0 - Gateway = 192.168.32.1 - type static = subnet

• configuration error static equivalent e3200

  My ISP requires static configuration.  I plugged in the numbers and trying to save get a message from the 192.168.1.1 page "value cannot be equal.  What does that mean?  The ip address of my router is the same as the default gateway.  I'm naïve, any help?

  Thanks for the reply.  I changed the ip of the router 192.168.2.1 and he accepted after a full reboot of the pc, modem, router.  Now configure the network.

• WRT120N - ip Routing Static-> connection drops

  Hello

  I'm having a problem with a WRT120N router to work. I'm trying to use this router to serve as a way for employees to connect to the domain of society everywhere in the company of their laptop.

  My problem: as soon as I set up a static ip address in the Web interface, the connection drops. I can't connect to the router more. Everything seems fine for a few seconds, but my internet connection in XP then says "limited or no connectivity."

  I used the correct data from our DHCP server and I put "DHCP server" on the WRT120N-Web interface to 'off '. My CARD is an Intel Pro Wireless 3945abg. I'm also using Intel's WiFi connection utility.

  Anyone know what could be the cause of the connection drops?

  I have already updated the firmware on the router to the latest version, but it did not solve my problem.

  The router is right next to me, so it is no more a problem.

  I also changed the Router 1 channel, but nothing has changed.

  Do not disable the DHCP server. Computers do not get an IP address and therefore indicates "limited connectivity".

  DHCP does not work through a router.

  Each IP subnet needs its own DHCP server. Otherwise, the value of the WRT automatic/DHCP back on the Internet. Unplug it from your network.

  Then change the address LAN IP of the router from 192.168.1.1 to 172.16.1.49 (free address). You will not be able to select the subnet mask 255.255.0.0 well (it is a limitation on all consumer of Linksys routers).

  In addition, disable the DHCP server and save settings now. Unplug your computer.

  Now one of the LAN ports numbered from your phone to your existing LAN WRT.

  Now that you have configured the WRT as access point for your network. Wireless computers get their IP address of your DHCP server.

  The incorrect subnet mask 255.255.255.0 on the WRT means that you will only be able to access the web interface of the WRT from a computer with IP 172.16.1. *. But it's the only issue here...

• How can I configure a static IP address in Windows Server 2008?

  original title: set static IP of Server 2008

  I have a Server 2008 R2 from a CD of demo loaded on a Dell computer.
  When I start my Poweredge 1950 server, I get these messages:
  ' F/W initialization devices 0% '.
  info on the RAID drivers
  "(HA-0 9Bus 2 Dev 14) PERC 5 / i integrated 5.0.1 - 0030"
  "The battery material is missing...". »
  "Source 1 or logical drives on the adapter to the host.
  Logic of 1 drive (s) handled by BIOS
  some information about the remote access configuration utility
  and then he told me that the IP subnet, gateway, are all 0.0.0.0

  I have to hit F1 to continue the boot or F2 to run the Setup utility.

  In the configuration under embedded devices utility, two network cards have TOE activated ability
  I don't seem to be able to assign the NETWORK adapter a static address, and he poses problem when I try to put in place AD DS services
  Server 2003, I read that the TOE function on the NETWORK card is loaded.  I can't disable in the BIOS screen.  I see solutions for
  This manipulation for Server 2003, but nothing for 2008.

  When I try to use installation of AD DS services in advanced mode and get to the screen to select additional options for this domain controller, and I check the DNS of the server, a warning is displayed saying that one or more physical network adapters don't have a static IP address.

  Any suggestions on how to set the static NIC card?

  Thank you

  Post in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• Cisco ASA Cisco 831 routing static. help with ACL, maybe?

  Hi all

  What should be a simple task turns out to be difficult and I really need help.

  The Cisco ASA obviously isn't a strong point on mine and could do with a point in the right direction. I hope that this will allow me to learn more about the ASA 5505.

  OK so I have an ASA 5505. VLAN 1 is 192.168.254.1 and VLAN 2 DHCP of my cable modem.

  I have a cisco 831 Ethernet router that will sit between my main LAN and my LAN test I want to implement for multicasting. the Cisco 831 has 1 Ethernet as 192.168.254.254 and Ethernet 0 is 10.1.1.1.

  The ASA I have an interior route 10.0.0.0 255.0.0.0 192.168.254.254.

  On the Cisco 831, there is a route 0.0.0.0 0.0.0.0 192.168.254.1. I can pass traffic via Cisco 831 to the ASA 5505 and internet, for example I can ping 8.8.8.8 and access everything on my main local network, but the other wan of any host inside the ASA 5505 is unable to ping anything on 10.1.1.x.

  Where I'm going wrong? I did all my access to my a whole ASA, but it is still unable to do anything.

  I will attached my configs with deleted passwords here and would like a good kick in the right direction. Without a doubt, it's something simple I'm missing and I'm sure it's with the ACL on the ASA 5505 like the packet tracer said that the package is abandoned due to the ACL

  Thank you. :)

  Thus, all traffic between these two LANs will travel on ASA, on the same interface.
  Then please add this command in the global configuration of the ASA:
  permit same-security-traffic intra-interface

• It is possible to configure router CISCO1921/K9 from site to Site vpn behind a firewall?

  I am looking to buy CISCO1921/K9 to configure vpn site to site with Amazon VPN. We are behind a firewall. I try to install the new CISCO1921/K9 router according to the scheme of quick text below. My setup work? and what are the ports will it transfer to my firewall?

  INTERNET--> Modem to ISP---> firewall - CISCO1921/K9

  Hi Paul,.

  (192.168.1.0/24) - router (10.1.1.1)-(10.1.1.2) firewall(81.92.61.x/27)---Internet

  The configuration is very simple...

  1. There will be no modifications on the configuration of the VPN router with the exception that the interface of the router (turning to the firewall) will be to have private IP 10.1.1.1

  2. you will need to take a public IP of your range of public (e.g. 81.92.61.2) and will share the same to your remote location which they set up as peers IP to their end.

  3. now you have to configure 2 NAT type on your firewall.

  NAT source:-when your router will initiate VPN

  Before NAT: Destination - Source 10.1.1.1-(homologous remote IP)

  After NAT: Destination - Source 81.92.61.2-(homologous remote IP)

  Destination NAT:-when the remote location will launch the VPN

  before NAT: Destination - Source (remote peer IP)-(81.92.61.2)

  After NAT: Destination - Source (remote peer IP)-(10.1.1.1)

  I hope this is clear :)

• Configuration of static translation "inverted".

  I am trying to configure a PIX with static translation "inverted".

  If I understand correctly, with conventional static translation if I want my host (10.10.10.10) inside to be 'visible' on the external interface like 192.168.5.5), would be my config: -.

  public static 192.168.5.5 (Interior, exterior) 10.10.10.10 netmask 255.255.255.255

  However, I have an external host (203.203.203.203) I want to be 'visible' inside interface as 10.10.11.11. I would have thought the config would be: -.

  public static 10.10.11.11 (exterior, Interior) 203.203.203.203...

  but it does not work. Is this possible and if so, how?

  Thanks to advnance.

  Jon

  FYI, here is a good URL.

  http://www.Cisco.com/warp/public/707/28.html#topic12

• How to configure routing in vSphere Client

  Hi all

  Could someone provide an explanation or a tutorial on how you are connecting routers using vSphere client? I used VyOS / Vyatta as a router in a VM and I'd like to send between networks. I heard you need to add a relay (between networks) router with an interface in each port group.

  Thanks for your help!

  I'm not a dedicated network guy, but I think that the roads should be slightly modified:

  ROUTER1:

  address 192.168.10.0 static route next hop 192.168.40.2 distance '1'

  address static road 192.168. 30192.168.40.2.0 next-hop distance '1'

  ROUTER2:

  address 192.168.0.0 static route next hop 192.168.40.1 distance '1'

  address the static road 192.168.10.2 192.168.30.0 next hop distance '1'

  Router3:

  address 192.168.40.0 static route next hop 192.168.10.1 distance '1'

  address static road 192.168. 0,.0 next hop 192.168.10.1 distance '1'

  André

• Article number: 28840 Smart wifi configuration router Linksys by using the Smart installer - missing a step?

  I guess that something is missing here?

  The tutorial goes from:

  Check if you are able to access the Internet by connecting the modem to the computer via an Ethernet cable

  TO:

  Step 1 - Connect your computer to the router by an Ethernet cable.

  No mention of the connection of the modem to the router first?

  Hmm. It seems you are right. If you have not connected the router to the modem, there are 4 step to the rescue.

  I hope someone from Linksys will see this and have fixed.

• Configuring router user name and password for Linksys WRT120N router?

  Im trying to forward my ports for games, but I can't access my router. I put the usernam admin and leave the password empty vice versa and user name password and username password vice versa. This is a new router and this is my first time trying to access.

  Thank you

  Well, it was an old password for quite awhile ago. I didn't know that he will use an old previous routers. ??? Weird. Well, I want to change the password and the user. where should I do all here?