Configuration of voltage and resistance 34970

Similar Questions

• Variables for voltage and current on each component (for use in graphically the diagram)

  Hello

  I have a very simple circuit containing only a source of AC voltage and resistance of two series.

  I want to draw the voltage of the source and each resistance. I can't find any variable involves pre right now, I know I und came to the value of the resistance.

  for example

  UR1 = I * r1

  USource = I *(r1+r2)

  It's pretty boring... especially because that put in square brackets does not work.

  probably the cause variables containing itselfes media.

  hope you have an idea

  THX

  Hello

  The way that you have set in place now of things is correct. Multisim, as well as most of other circuit simulators, monitors the node voltages, no voltage drops. When you draw your diagram, Multisim assigns numeric node names to each node. That's why you see v(1) and v(2) and not something like V (R2). To find the voltage drop in R2, you will need to calculate V (2) v (1). To know the name of each of your nodes (also called threads), simply do the following:

  1. Click Options > properties sheet
  2. For option Net names, select Show all
  3. Click OK

  To make it easier for you, you can name a few nets to something that is easier to read. You can do this:

  1. Double-click on the net you want to rename (the net is the wire you drew connecting elements)
  2. Enter your name, preferred net in the space provided
  3. Click OK

  Hope that answered some of your questions.

• How to display the voltage and current of synchronously

  Recently, doing a project on the acquizeing voltage and current synchronouly, then display. the design is welding a resistor(1%) 0.5 ohm in NI 6251 entered analog of her HAVE differential, then acquired the differential voltage at the input to convert current. At the same time, I hope to recover the path of analog input voltage. My problem is that the current profile data. Please help me .the program screenshot is show below. ---1. Perhaps you ask why not use no. - a way to get voltage at all port of AI, then in the use of the software less to get a voltage inputs HAVE. in this way, my problem is solved. I try, but the current accuracy is failure. because my current range expect is 1uA ~ 100mA. precision current samll won't be promised if you use simple ways for granted NOR 6251 voltage. NEITHER 6251 device spec (HAVE an absolute precision) (v) nominal range sensitivity absolute Accuracy (uV) 10 1920 112 5 1010 56 2 410 22.8 74 0.2 6.4 0.1 52 6.0 (I want to use this range to measure current samll) - cordially Shawnh.Chen

  shawn1 wrote:
  1. how show the waveform by accumulating 1 d data table, rather than showing all 100 acquisition

  Use a waveform graph.  Graphics keep history, you do not have to accumulate the data.  He does it for you on the screen.

  shawn1 wrote:
  2. What is the minimum unit of identification of the TSC103IPT amplifier? I doubt that the 0.5uA can be identified? (0.5uV = 0.5 ohm * 1uA) Because I can't find anything on the auccary in TSC101IPT datasheet.

  The amplifier is analog.  Thus, he can win anything.  But you should really think about a higher resistance if you really want to measure this small of a current.

• silent install Firefox 27.1 and configuration (homepage, proxies and bookmark)

  Hello
  I am trying to perform a silent installation and configuration for 27.1 Firefox but I'm not able to get the same results I got with the 26 versions and below. For these versions, I used the method described in this link:
  http://www.mockbox.NET/ConfigMgr-SCCM/174-install-and-configure-Firefox-silently
  But for Firefox 27 creating the Mozilla.cfg and other files doesn't seem to work. Could you please tell me how silently configure the proxies and the homepage on Firefox 27.1 during installation. I also need to add a bookmark while installing. Could you please tell me how to do the same? I found a few methods saying that I had to change a bookmark.html file, but I don't think that this file is present on firefox 26 on.
  Thank you in advance.
  Kind regards.

  Learn more about this add-on.
  
  https://addons.Mozilla.org/en-us/Firefox/addon/cck2wizard/

• I format the machine. How to back up the configuration of Firefox and bookmarks for re-installing later?

  I need to reinstall my operating system to windows 7. Firefox works fine. All I need is a procedure to save the configuration of Firefox and bookmarks to facilitate the configuration process when I re - install Firefox later. Thank you

  Firefox stores all your information in a folder called "account profile". If you back up to the top (on a USB key, for example), you can copy it back later after you have reinstalled your computer (including Firefox, of course) and all your settings, passwords, bookmarks, etc. will be present again. Take a look at: back up and restore the information contained in the profiles of Firefox.

• Measure the voltage and the temperature simultaneously with PCI-6281

  Measure the voltage and the temperature at the same time at the same time. However, when I put the voltage and temperature in a loop, the acquisition of voltage is significantly delayed. When I put the voltage and temperature in two different loop, none of them works.  There is an example in aid of Labview as shown. This structure works fairly quickly? In addition, how a volgate get and temperature Analog DBL 1Chan 1Samp? I check the exported excel, the first column is 0, 1 the second column contains the value of the voltage, temperature value. I wonder how can I get these two values for each scan.

  ,

  Assuming that the DAQ cards can handle it, you can set an analog trigger for the channel of the tension.  Then you just X samples to get your 100us data value.  Keep the last sample.

• 6218 USB voltage and pulse acquisition

  I use the USB-6218 to run 2 OR task at the same time in my vi. A task is to acquire a pressure transducer voltage and scaling it. The other task is the counting of pulse frequency with a flow meter and scale. Both tasks will work perfectly when I run them in Max, or run individually in my vi as a sub - vi. But when I try to run at the same time as I get wrong the meter reading of. It seems that the meter is losing his job after its first reading. Each task is written in its own subvi who takes a sample, and I'm sure that the task has stopped before that starts the other task. I don't get any errors, but I have to stop and restart the computer to clear the task of counter before he can start to read correctly.

  Hello joe_n1,

  It seems that this question is because of the way you use your tasks in subVIs.  If you create a task and then delete it each time, then every time that the task starts off fees.  As you say, he will lose his job after the first reading.

  To avoid this problem, make sure that you are only to create the task (usually at the beginning of your VI) once and then once compensation (usually at the end of your VI).  Really, the only thing you have to repeat is the actual readings DAQmx.  For this reason, I would not recommend putting your tasks in subVIs.  You shouldn't have to stop each task before the other begins - rather, you should be able to run them simultaneously.

• At the start, my phone freezes on the configuration of updates and restarts

  At startup, my phone freezes on the configuration of updates and restarts. It won't let me even put my password. Automatically, it restarts and continues to do the same thing over and over again... I need help!

  What were the results of the test of the hard drive?

  It seems that things go too far and you need to perform a factory restore and reinstall the files on your system.

  Repeatedly press the F11 key at startup to enter the Recovery Manager, and then follow the instructions.  I hope that the recovery partition is not damaged.

• Why can't acquire data from strain and resistance at the same time with a NI 9219 module?

  Hello

  I use a chassis with a NI9219 module 9172 cDAQ to try to acquire the strain and resistance at the same time, with the Labview SignalExpress software.  Is this possible?  When I try to display two values of signal at the same time, I get an error of assistant DAQ 50103 'the specified resource is reserved.  The operation could not be performed as indicated.  I used to be able to acquire the strain and tension at the same time, but now even that gives me error 50103.  I have hours trying to figure this out.  Any help would be greatly appreciated.

  Thank you

  Justin

  That's all!  Thank you very much, now I can sleep tonight - seriously!

  Thanks again,

  Justin

• Measure the voltage and the temperature at the same time with a single card PCI 6014 DAQ?

  Hello guys,.

  I'm doing a charger measuring the voltage of the battery, the charge current and the temperature of the battery using a 6014 cardboard...

  I want to use my PCI6014 DAQ card to measure 2-channel analog voltage input and 1 temperature Channel Analog input using thermocouple type k measurement of voltage or temperature isolation is OK, but I can't understand how to measure the voltage and the temperature at the same time... I want to use input differential...

  Thank you in advance, all the tips

  YSL

  Create a task and add channels to the task, as follows:

  

  Christian

• scanning voltage and current measurement for Keithley 2400

  Dear all

  Hello

  can someone help me?

  Despite days nearlly10 I am option to find any program LabVIEW 2010 for sweeping the voltage and measure current who works with RS-232, I have a end not have nothing exept examples read single and multiple data. I tried to SmartData labview and changed a few prorgram gpib to RS - 232, but I couldn't.

  In another attempt to find a good VI "votltage scanning and current measurement" that work with RS-232 in labview 5.1.1. I have converted in 2008, but it takes old driver (ke24xx.dll) and do not work in my labview 2010 and I could ' t find older driver.

  My thesis project was halted in those 10 days, and I couldn't do anything for our keithley.

  Please helpe...

  in the following, I have attached these files:

  1.-first, what voltage scan that works with GPIB

  2 - Vi that I change the gpib for visa (rs232) port that I don't know why it doesn't work.

  3. it is Vi related to the "sweeping and current measurement votltage" that works with the RS-232, but it takes old dirver so I can't use it.

  4-slot-VI necessary for the implementation of program 3 (but there is no driver for these subVIs) was attached to the reply message of this post

  If any body has this program ("scan votltage and current measurement" running rs - 232) please send to me

  Thanks in advance.

  None of you attached the screws are the driver OR you spoke. There is no conversion required for this driver.

• calculate the symmetrical components of voltage and current

  Hi all. I work on the calculation of symmetrical components of voltage and current in Labview. I have included the relationship between the symmetrical components and sequence as photo 1 voltage. I'm going to use this calculation for several times, so I wonder if anyone has some ideas far better bc I wired just so much together to realize the expression. It seems aweful. Any suggestion? as built-in function to achieve this function? Thank you

  Let's take a look on your form (you don't say what is complex, etc, so modify as needed)

  

  For example, here is how you create the matrix A to an alpha given.

  

  Similarly, you can create A ^(-1) matrix (your definition of A and A ^(-1) seem incompatible, otherwise you could just pick matrix inverse of A). After that, you can multiply with you V123 vector using AxB.

• Chroma DC power supply RS232 communication (read problem of over-voltage and current)

  Dear all.

  I chroma programmable DC power. Based on the programming of the Instrument manual I develop using RS232 communication. Based on the program I can set the voltage, current, over-current protection, protection against overvoltages and make IT / OFF out put supply perfectly.

  But I have to read the measured values of the output power as current and voltage. Measured applications are the voltage and current of the output of the power supply. My problem is two of them read at the same time. Currently, the reading is only voaltge or current (if the first request is v? it is voltage read out but no reading for the current) and if the first request is CURR? the reading for the current, but not for VOLT? The status message is OK, even if it is to read values.

  Thanks in advance

  What I see in your program, it's that you do not use the stop for reading character. For your writing, you do the hard with all these concantanate string functions. You can set the stop character for all entries with a node unique propert - "ASRL end Out.

• the API system configuration error 1097 and freezes

  I used successfully the API system configuration to detect and read information on a PXI chassis.

  But now, when I try to initialize and collated all information using a simple VI, the system returns error 1097 and crashes before the end of the VI.  Based on that the stop button does not work and I have to either soft or hard reboot the machine.

  I have attached a screenshot of it in a frozen state and error, like a report of what is installed on my system.

  The only thing I can think has changed since this last worked has been upgraded my MAX and other pilots from 5.5 to 14.0 and then the latest version as of today.

  It is usually the generic error, which means that some external code access violated the integrity of the system and the memory is likely to have been corrupted in the process. Since it is a NI API system AND it seems to have worked before, I guess it's not a bad disigned call library node, but a form of bribery in external code library itself which implements the API of the System Configuration.

  Reinstalling may solve the problem.

• How can I put the Windows XP firewall in a port configuration 'allow all' and only block some ports?

  Without going into the details of why I need to do this, I'm putting the firewall of Windows XP in one allow all the configuration of ports and only refuse some ports I have in a list.

  I train this script via the command-line batch with the netsh firewall add portopening command.  From what I've read, if enabled the firewall denies all traffic and only allows ports with exceptions, so through batch scripts, I opened all the 65 000 + ports TCP and UDP, essentially with the firewall turned on but in a configuration of "allow all the»  I don't deny the 100 or so ports to my list that I want blocked after they are all open.

  This strategy seems to work, but the problem I waited and I now see is that svchost.exe takes 50% of my CPU time, have to deal with constantly these firewall rules.

  "From what I've seen on Windows XP, there is no way to have the firewall ON, and in a configuration of" allow all the "" because the XP firewall may not have defined port ranges, they must be defined one by one.  It looks like Windows Vista or 7 would be much easier because the firewall has got a re vamp of advanced features.

  Does anyone have a suggestion on how to realize this "allow all", deny some' strategy?  I know it's a strange use of the Windows Firewall, so let's please jump in front of a 'why would you do this incredibly stupid thing?"messages.

  Also, if it was the wrong forum (or website) to post on for this kind of question, I'd appreciate a recommendation of a more appropriate forum.

  Hello

  See the steps in the following article.

  How to manually open ports in Internet Connection Firewall in Windows XP?

  http://support.Microsoft.com/kb/308127