Variables for voltage and current on each component (for use in graphically the diagram)

Similar Questions

• How to set global variables for use by all THE #subform [0] items of form1. ?

  Hi all

  I don't know how to code javascript but am new to Adobe LiveCycle.  When I open the script editor, I have the following code (the code is in United Nations in bold):

  -form1. #subform [0]: initialize :-(FormCalc, client).

  //////////////////////////////
  TO START: SET GLOBAL PRICES.
  //////////////////////////////

  var Cityscope_Sydney_CostUser1 = 60,39;
  var Cityscope_Sydney_CostUsers2to5 = 3.02;
  var Cityscope_Sydney_CostUsers6to20 = 1.21;
  var Cityscope_Sydney_CostHardCopyWithOnline = 14.59;
  var Cityscope_Sydney_CostHardCopyWithoutOnline = 54,67;
  var Cityscope_Sydney_CostHardCopyAdditional = 14.59;

  var Cityscope_NorthSydney_CostUser1 = 48,40;
  var Cityscope_NorthSydney_CostUsers2to5 = 2.42;
  var Cityscope_NorthSydney_CostUsers6to20 = 0.97;
  var Cityscope_NorthSydney_CostHardCopyWithOnline = 14.59;
  var Cityscope_NorthSydney_CostHardCopyWithoutOnline = 43,54;
  var Cityscope_NorthSydney_CostHardCopyAdditional = 14.59;

  
  ////////////////////////////
  END: SET GLOBAL PRICES.
  ////////////////////////////

  -form1. #subform [0]: enter :-(FormCalc, client).

  -form1. #subform [0]: output :-(FormCalc, client).

  -form1. #subform [0]: calculate :-(FormCalc, client).

  -form1. #subform [0]: validate :-(FormCalc, client).

  -form1. #subform [0]: preSave - (FormCalc, client).

  < < = etc etc etc = > >

  -form1. #subform [0]. Item1Cost::initialize :-(JavaScript, client).

  -form1. #subform [0]. Item1Cost::enter :-(FormCalc, client).

  -form1. #subform [0]. Item1Cost::exit :-(FormCalc, client).

  -form1. #subform [0]. Item1Cost::calculate :-(JavaScript, client).

  Store the values of the form of friendly names.
  var AreaSelected = Item1Area.rawValue;
  var NumberOfUsersSelected = Item1Users.rawValue;

  Declare other variables.
  var Users1Calculation;
  var Users2to5Calculation;
  var Users6to20Calculation;

  
  Calculate the cost to the "components" user will depend on the number of users selected for the region.
  Switch (true)
  {
  If (NumberOfUsersSelected < 2):
  Users1Calculation = NumberOfUsersSelected * Cityscope_Sydney_CostUser1;
  Users2to5Calculation = 0.00;
  Users6to20Calculation = 0.00;
  break;
  If (NumberOfUsersSelected > 1 & & NumberOfUsersSelected < 6):
  Users1Calculation = Cityscope_Sydney_CostUser1;
  Users2to5Calculation = (NumberOfUsersSelected - 1) * Cityscope_Sydney_CostUsers2to5;
  Users6to20Calculation = 0.00;
  break;
  If (NumberOfUsersSelected > 5):
  Users1Calculation = Cityscope_Sydney_CostUser1;
  Users2to5Calculation = 4 * Cityscope_Sydney_CostUsers2to5;
  Users6to20Calculation = (NumberOfUsersSelected - 5) * Cityscope_Sydney_CostUsers6to20;
  break;
  by default:
  Alert ("BROKEN: calculate the individual components of cost of use will depend on the number of users selected for the region.");
  }

  apply the total cost for this article
  Item1Cost.RawValue = Users1Calculation + Users2to5Calculation + Users6to20Calculation;

  -form1. #subform [0]. Item1Cost::validate :-(FormCalc, client).

  -form1. #subform [0]. Item1Cost::MouseEnter :-(FormCalc, client).

  -form1. #subform [0]. Item1Cost::mouseExit :-(FormCalc, client).

  -form1. #subform [0]. Item1Cost::change :-(FormCalc, client).

  -form1. #subform [0]. Item1Cost::full :-(FormCalc, client).

  -form1. #subform [0]. Item1Cost::MouseUp :-(FormCalc, client).

  -form1. #subform [0]. Item1Cost::MouseDown :-(FormCalc, client).

  -form1. #subform [0]. Item1Cost::click :-(FormCalc, client).

  -form1. #subform [0]. Item1Cost::preSave - (FormCalc, client).

  -form1. #subform [0]. Item1Cost::postSave - (FormCalc, client).

  -form1. #subform [0]. Item1Cost::prePrint - (FormCalc, client).

  -form1. #subform [0]. Item1Cost::postPrint - (FormCalc, client).

  -form1. #subform [0]. Item1Cost::preSubmit:form - (FormCalc, client)-

  -form1. #subform [0]. Item1Cost::docReady - (FormCalc, client).

  -form1. #subform [0]. Item1Cost::docClose - (FormCalc, client).

  -form1. #subform [0]. Item1Cost::ready:form - (FormCalc, client)-

  -form1. #subform [0]. Item1Cost::ready:layout - (FormCalc, client)-

  -form1. #subform [0]. Item1Users::initialize :-(FormCalc, client).

  -form1. #subform [0]. Item1Users::enter :-(FormCalc, client).

  -form1. #subform [0]. Item1Users::exit :-(FormCalc, client).

  -form1. #subform [0]. Item1Users::calculate :-(FormCalc, client).

  -form1. #subform [0]. Item1Users::validate :-(FormCalc, client).

  -form1. #subform [0]. Item1Users::MouseEnter :-(FormCalc, client).

  -form1. #subform [0]. Item1Users::mouseExit :-(FormCalc, client).

  -form1. #subform [0]. Item1Users::change :-(FormCalc, client).

  -form1. #subform [0]. Item1Users::full :-(FormCalc, client).

  -form1. #subform [0]. Item1Users::MouseUp :-(FormCalc, client).

  -form1. #subform [0]. Item1Users::MouseDown :-(FormCalc, client).

  -form1. #subform [0]. Item1Users::click :-(FormCalc, client).

  -form1. #subform [0]. Item1Users::preSave - (FormCalc, client).

  -form1. #subform [0]. Item1Users::postSave - (FormCalc, client).

  -form1. #subform [0]. Item1Users::prePrint - (FormCalc, client).

  -form1. #subform [0]. Item1Users::postPrint - (FormCalc, client).

  -form1. #subform [0]. Item1Users::preSubmit:form - (FormCalc, client)-

  -form1. #subform [0]. Item1Users::docReady - (FormCalc, client).

  -form1. #subform [0]. Item1Users::docClose - (FormCalc, client).

  -form1. #subform [0]. Item1Users::ready:form - (FormCalc, client)-

  -form1. #subform [0]. Item1Users::ready:layout - (FormCalc, client)-

  .. and so on and so forth...

  In short, I want the code in:

  -form1. #subform [0]. Item1Cost::calculate :-(JavaScript, client).

  .. .to be able to access the variables I created in:

  -form1. #subform [0]: initialize :-(FormCalc, client).

  
  (I guess that's where I store global variables)

  At this point, global variables are not accessible with the above configuration.  Was the only one I can get this working is to cut and paste the Globals in each item of form1. #subform [0], which of course defeats the purpose of global variables!  I intend to have a lot more items so wouldn't duplicate global variables for each of them!

  Can someone show me how to do this?

  Any help is very appreciated!

  Thank you

  Stanbridge

  Post edited by: stanbridgej - colors and fonts or not will not save.  Are bolded my question make (non-fat) code easier to read (I hope).

  I haven't used Formccalc, but I thought it would be the same regardless. Insert a script object to the top of the hierarchy and call it, for example "sco." Paste the Globals. Then refer to variables of the extent that sco. Cityscope_Sydney_CostUser1, etc. Make one

  App.Alert (sco. Cityscope_Sydney_CostUser1);

  one of the fields. If the debugger is activated, it will tell you if it cannot resolve the reference as "sco. In this case, you may need to use the som expression to reference the script object, for example

  var scoScript = xfa.resolveNode ("topOfHierarchy.sco");

  scoScript.Cityscope_Sydney_CostUser1

  But if as close as possible to the top of the hierarchy above should work.

• How to display the voltage and current of synchronously

  Recently, doing a project on the acquizeing voltage and current synchronouly, then display. the design is welding a resistor(1%) 0.5 ohm in NI 6251 entered analog of her HAVE differential, then acquired the differential voltage at the input to convert current. At the same time, I hope to recover the path of analog input voltage. My problem is that the current profile data. Please help me .the program screenshot is show below. ---1. Perhaps you ask why not use no. - a way to get voltage at all port of AI, then in the use of the software less to get a voltage inputs HAVE. in this way, my problem is solved. I try, but the current accuracy is failure. because my current range expect is 1uA ~ 100mA. precision current samll won't be promised if you use simple ways for granted NOR 6251 voltage. NEITHER 6251 device spec (HAVE an absolute precision) (v) nominal range sensitivity absolute Accuracy (uV) 10 1920 112 5 1010 56 2 410 22.8 74 0.2 6.4 0.1 52 6.0 (I want to use this range to measure current samll) - cordially Shawnh.Chen

  shawn1 wrote:
  1. how show the waveform by accumulating 1 d data table, rather than showing all 100 acquisition

  Use a waveform graph.  Graphics keep history, you do not have to accumulate the data.  He does it for you on the screen.

  shawn1 wrote:
  2. What is the minimum unit of identification of the TSC103IPT amplifier? I doubt that the 0.5uA can be identified? (0.5uV = 0.5 ohm * 1uA) Because I can't find anything on the auccary in TSC101IPT datasheet.

  The amplifier is analog.  Thus, he can win anything.  But you should really think about a higher resistance if you really want to measure this small of a current.

• calculate the symmetrical components of voltage and current

  Hi all. I work on the calculation of symmetrical components of voltage and current in Labview. I have included the relationship between the symmetrical components and sequence as photo 1 voltage. I'm going to use this calculation for several times, so I wonder if anyone has some ideas far better bc I wired just so much together to realize the expression. It seems aweful. Any suggestion? as built-in function to achieve this function? Thank you

  Let's take a look on your form (you don't say what is complex, etc, so modify as needed)

  

  For example, here is how you create the matrix A to an alpha given.

  

  Similarly, you can create A ^(-1) matrix (your definition of A and A ^(-1) seem incompatible, otherwise you could just pick matrix inverse of A). After that, you can multiply with you V123 vector using AxB.

• Chroma DC power supply RS232 communication (read problem of over-voltage and current)

  Dear all.

  I chroma programmable DC power. Based on the programming of the Instrument manual I develop using RS232 communication. Based on the program I can set the voltage, current, over-current protection, protection against overvoltages and make IT / OFF out put supply perfectly.

  But I have to read the measured values of the output power as current and voltage. Measured applications are the voltage and current of the output of the power supply. My problem is two of them read at the same time. Currently, the reading is only voaltge or current (if the first request is v? it is voltage read out but no reading for the current) and if the first request is CURR? the reading for the current, but not for VOLT? The status message is OK, even if it is to read values.

  Thanks in advance

  What I see in your program, it's that you do not use the stop for reading character. For your writing, you do the hard with all these concantanate string functions. You can set the stop character for all entries with a node unique propert - "ASRL end Out.

• I downloaded just standard CS6 for windows and that you do not have an .exe for the installation file. I have a 7z file and an application file that I used to extract the 7z files. I am now at a fixed support.

  I downloaded just standard CS6 for windows and that you do not have an .exe for the installation file. I have a 7z file and an application file that I used to extract the 7z files. I am now at a fixed support.

  Hello

  You must download the file [.7z] 1 and 2 [.exe] file. Once downloaded, keep both files in the same folder.

  Then run the .exe file and it will extract the CS6 Installer for you. With which you can install your software CS6.

  For CS6 direct download link: https://helpx.adobe.com/x-productkb/policy-pricing/cs6-product-downloads.html

  You can also check this link: https://helpx.adobe.com/creative-suite/kb/cs6-install-instructions.html

  In the case of additional assistance, feel free to contact support by calling/chat for cancellation requests and billing queries:

  Contact the customer service

  * Be sure to stay connected with your Adobe ID before accessing the link above *.

  I hope it helps.

  P.S. If you use the adobe forums, please check useful/correct responses of staff or assistance, if there is.

  Concerning

  Ludo has

• scanning voltage and current measurement for Keithley 2400

  Dear all

  Hello

  can someone help me?

  Despite days nearlly10 I am option to find any program LabVIEW 2010 for sweeping the voltage and measure current who works with RS-232, I have a end not have nothing exept examples read single and multiple data. I tried to SmartData labview and changed a few prorgram gpib to RS - 232, but I couldn't.

  In another attempt to find a good VI "votltage scanning and current measurement" that work with RS-232 in labview 5.1.1. I have converted in 2008, but it takes old driver (ke24xx.dll) and do not work in my labview 2010 and I could ' t find older driver.

  My thesis project was halted in those 10 days, and I couldn't do anything for our keithley.

  Please helpe...

  in the following, I have attached these files:

  1.-first, what voltage scan that works with GPIB

  2 - Vi that I change the gpib for visa (rs232) port that I don't know why it doesn't work.

  3. it is Vi related to the "sweeping and current measurement votltage" that works with the RS-232, but it takes old dirver so I can't use it.

  4-slot-VI necessary for the implementation of program 3 (but there is no driver for these subVIs) was attached to the reply message of this post

  If any body has this program ("scan votltage and current measurement" running rs - 232) please send to me

  Thanks in advance.

  None of you attached the screws are the driver OR you spoke. There is no conversion required for this driver.

• Venue Pro 8: use the charger with a little more voltage and current?

  I just bought a Dell came Pro 8 tablet used running Windows 8.1. The seller didn't have the original charger, so he gave me a 12W of Apple loader that had taken out nominal 5.2V and 2. 4A

  Is it okay to use this charger for my Tablet? Any potential problems in the long term?

  Thank you!

  I'm sure that the voltage is OK to 99.9%.  The extent of the current note goes, which is often misunderstood.  The rated current for a charger power or power is the maximum that the charger/power is able to provide. It could be evaluated to a zillion amps, but the equipment to which it will draw only what it requires.

• Phaser in LabVIEW for voltage and current indicator

  When I read a research paper on the power system, I've seen has a reasearcher program LabVIEW (its block diagram is not shared just GUI). My question is: is-LabVIEW has a built-in function that allows to display the amount of complex in | Mag |

  

  Greetings muahang1234

  There is a suite for LabVIEW called Suite of electrical power OR LabVIEW that might interest you. Visit ni.com and evaluate the software, it may be the tool you're looking for!

  Let us know how it goes. Nice day.

• 6009OEM output voltage and current

  Hi all

  Just try to make sense:

  http://www.NI.com/PDF/products/us/20043762301101dlr.PDF

  Page 3 says: high output voltage (push - pull, I = - 8.5 my) = minimum voltage 2.0 v maximum voltage = 3.5V but where can I find out what current can it provide and continue to produce an output voltage more than 4.2V?  (4, 2V is the worst case for the high threshold of logic of a chip, I want to control).

  Thank you!

  J

  Hello J,

  As you mentioned is the maximum voltage of 3.5V when you have a high output voltage (push - pull, I = - 8.5 my). If you need more than 3.5V then you might need to change to an open-drain output. As you can see from the link you provided that you would receive a maximum voltage of 5V.

  If you do not use an open-drain output you have to combine with a pull up resistor.

  I hope this helps.

• my project is to measure the voltage and current by using the view of laboratory.

  Dear Sirs,

  I have a project to measure parameters electric ac current, voltage, power factor etc through aquisitioin of data with labview. Can I do this? If yes then kindly help me with some opinions and ideas. I'll be very grateful to you.

  Muhammad Azam Hanan.

  Student of the University of engineering and Technolgy, Lahore, Pakistan.

  
  

• data acquisition in line voltage and current signals

  What is the name and model of the instrument OR measure the 220V 3-phase, 5 signals? Also, what will be the approximate cost of this equipment (s)?

  Hello Yasink,

  Looks like you could do reference the entry Module current 5A with insulation of 250Vrms, NI 9227.

  Can you provide more information on the app you want? From there I was able to provide a better recommendation.

• I have my ID Windows Live ID have not used for quite awhile and I would like to start using it again, the live ID is always committed, however I don't remember the password

  Hello, I have my ID Windows Live ID have not used for some time and I want to start using it again, live ID is always committed but I don't remember the password and I can't use the reset password option because I don't know that it is marked and "inactive".  Please let me know promptly if you are able to reactivate my live ID.  Once you answer this, I will use the live id address.  Thank you in advance.

  original title: can reactivate you my windows Live ID?

  Hello, I have my ID Windows Live ID have not used for some time and I want to start using it again, live ID is always committed but I don't remember the password and I can't use the reset password option because I don't know that it is marked and "inactive".  Please let me know promptly if you are able to reactivate my live ID.  Once you answer this, I will use the live id address.  Thank you in advance.

  It is a peer-to-peer (user forum.  You don't talk to Microsoft directly.  The answerto your question is, "No."

  Windows Live Solution Center - HotMail - HotMail Forums Solutions
  http://windowslivehelp.com/

  Hotmail - Forums
  http://windowslivehelp.com/forums.aspx?ProductID=1

  Hotmail - Solutions
  http://windowslivehelp.com/solutions.aspx?ProductID=1

  How to contact Windows Live Hotmail Support
  http://email.about.com/od/hotmailtips/Qt/et_hotmail_supp.htm

  Windows Live Hotmail Top issues and Support information
  http://support.Microsoft.com/kb/316659/en-us

• Try buying LR6 updated, select update and current product, select Add to cart, go to the basket page and it is empty :(

  I can't buy the update

  UPDATE seems that it works with IE, chrome, but even with IE, it takes a lot of time to fill the screen with the news, even when you check out.

  Java script is the worst.  Something as simple as a check out the basket and can't do things.

  Products

  If it's the link that fails for you, remove the cookies from the adobe.com site and try again or contact adobe support by clicking here and, when available, click on "still need help," https://helpx.adobe.com/contact.html

• BlackBerry Q10 Q!) hot and current battery dieng after aboiut 4 hours after the update of 10.3.1.1779

  I read a lot of posts on the forum (thanks), but nothing yet BlackBerry on the way to solve this problem. As a new user of Blackberry (back to BB after many years), I struggle with all the different advice given. Is there a definitive right answer yet as to how to solve this problem? In other words, how stop the Android player to run continuously and consume the battery life? All the most popular boards. I don't really want to wipe my phone and start all over again if there is another way. However, my phone of Q10 is uesless with this problem.

  No I do not have downlaoed all the Android files. At the end of the day, I consulted the disc of the Q10 and removed the android files. Then powered market and this seemed to solve the problem. Also, since the Blackberry has updated the operating system at 10.3.2.2474 and so far, this version does not seem the same have heating and remove the battery problem.

  Hallelujah!