configurations of ports required for licensing

Similar Questions

• Port Requirment for monitoring remotely with the Infrastructure Officer.

  Hi all

  Quick question, I have a Windows 2008 host in 'DataCenterA' that I installed a local Agent Manager and have deployed the agent infrastructure (5.6.6)

  I want to monitor a host Windows 2008 in 'DataCenterB '. I set this up, but I am told alarm

  Could not establish a connection to the lo3wpfogfms001.dcsprod.dcsroot.local: HTTP request failed [caused by: denied connection to http://lo3wpfogfms001.dcsprod.dcsroot.local:5985]

  This would be due to a firewall blocknig this port. If telnet to this port also fails instantly?

  If so this agent always uses this port?

  Hello Mike,.

  Have you configured listener winrm 'l03wpfogfms001 '?  5985 is the default listening port

  http://eDOCS.quest.com/Foglight/565/doc/core/FglAMInstallation/WindowsConfig.073.3.php

  Also, have you checked to see if your RPC service is running?  Also please check for all antivirus software.

  The fglam use WMI If WinRM fails.

• Required for NAC firewall ports manager manage/add the Cisco switch

  Hello

  I am trying to add switches cisco for the NAM, but I am not able to add the switch I get the error "unable to control switch" I tried opening ports 161-162 on the firwall; If I were to allow all traffic between the NAM and the switch, cisco NAM is able to add/manage the switch.

  Do not know what are the other ports may be required for cisco NAM for managing the switch?

  Thank you.

  Hello

  As far as I KNOW, only UDP 161 and 162 for SNMP communication ports must be open.

  Please make sure that you have configured the correct port on the switch:

  (config)# snmp-server host 172.16.1.61 traps version 2c cam_v2 udp-port 162 mac-notification snmp 

  If still does not, I would check the logs on the firewall for any traffic blocked between the cam and the switch.

  HTH,

  Tiago

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Required for PeopleSoft Campus Solution firewall ports

  Dear gurus,

  We are using PeopleSoft Campus Solution and running on Windows Server 2008 R2. Now, we are working on the conduct of firewall does so we can allow only the required ports for the application to work. Could you please tell what are the ports required on the demand side?

  Thank you.

  Only two ports is required to open the firewall if you use SSL and NON SSL via internet.

  Assume that your Web server uses port 80 and 443 for SSL and Non SSL respectively. Then, you need to open these 2 ports in the firewall.

  Hope that helps.

  P.S. Please check reply as an useful answer or appropriate so that it is useful for others who have the same issues. @

• What configuration of VLAN requires a switch connectivity defined as an access port?

  What configuration of VLAN requires a switch connectivity defined as an access port?

  By external switch tagging

• VMRC requires the license for use or free

  is that the VMware Remote Console tool requires the license for use or free? Thank you very much...

  In my view, it is covered by the vCenter license. As long as you have licensed vCenter (as far as I know on any edition), then you can use VMRC to any number of users.

• A license is required at the VASA? A license is required for each copy? VSI is necessary to have the VASA? They are mutually exclusive? VSI need NOTTM?

  A license is required at the VASA? A license is required for each copy? VSI is necessary to have the VASA? They are mutually exclusive? VSI need NOTTM?

  Thanks in advance.

  Assuming that you are referring to EMC arrays.

  License to the VASA: No.

  VSI required at the VASA: No. they work very well together, but does require that the other.

  VSI allowing VAAI: No. VAAI is active with or without the VSI.

• License is required for Sql Loader?

  I find that Sql Loader could save a lot of time for me in bulk insertion.
  
  But I do not know if the license is required for use in the development of commercial software.
  Or is there an API that can provide similar features of Sql Loader?

  I think sqlloader is a standard utility and it is included in the price of SE.

  You can see the details at http://www.oracle.com/technetwork/database/database10g/overview/twp-general-10gdb-product-family-132973.pdf

• What is the hardware configuration required for El Capitan?

  Where can I find a list of the hardware requirements for El Capitan?

  OS X El Capitan - technical specifications

• License required for "Automatic SQL Tuning Advisor"?

  I noticed a lot of databases in my company show using a component called "Automatic SQL Tuning Advisor" or "Automatic maintenance - Setup SQL" in DBA_FEATURE_USAGE_STATISTICS.

  Do we know if this component requires a License Pack Tuning or it could be one of the internal out-of-box/system uses that do not require a license?

  Thank you!

  I need a License Pack - Tuning

  Options and Packs

  MOS Doc ID 276103.1

  Best to check with your sales representative

• The switch configuration of 6500 catalyst for IPS Inline the METHOD works

  I understand how to configure the switch Catalyst 6500 so that the monitoring of ports are access ports in two VLAN separate operation online.

  However, I don't see any document that describes how the desired VLAN traffic gets forced through the IPS.

  "Promiscuous" mode, you can use copy/capture VACL and forwards traffic wished the METHOD of analysis. I don't see how to get traffic desired through the IPS.

  Note that the 6500 host is running native SXE IOS 12.2 (18).

  Thanks for any help.

  A transparent firewall is a pretty good comparison.

  Say you have vlan 10 with 100 PCs and 1 router for the network.

  If you want to apply a transparent firewall on this vlan you can put not just the Firewall interface on vlan 10. Nothing would go through the firewall.

  Instead, you need to create a new vlan, say 1010. Now you place the Firewall interface on vlan 10 and the other on the vlan 1010. Nothing is still going through the firewall. So now move you that router from vlan 10 to vlan 1010. Everything you do is to change the vlan, IP address and the mask of the router remain the same.

  The firewall transparent bridge vlan 10 and vlan 1010. The SCP on the vlan 10 ae is able to communicate and through the router, but must go through the transparent firewall to do.

  The firewall is transparent because there no IP Route between 2 VLANS, instead, the same IP subnet is on the VLAN and the transparent firewall ensuring the beidges between the 2 VLANS.

  The transparent firewall can do firewall between the SCP on the vlan 10 and the router on vlan 1010. But PC has vlan 10 talks for PC B on vlan 10, then the transparent firewall does not see and cannot block this traffic.

  An InLine sensor is very similar to the transparent firewall and will fill between the 2 VLANS. And similarly an InLine sensor is able to monitor InLine between PCs traffic on vlan 10 and the router on vlan 1010, but will not be able to monitor the traffic between 2 PCs on vlan 10.

  Now the PC on the other vlan and the router on a virtual LAN is a classic deployment for the sensors online, but your VLAN need not be divided in this way. You can choose to place some servers in one vlan and desktop to another vlan. You subdivide them VLAN to whatever the logical method for your deployment.

  Now for the surveillance of several VLANs the same principle still applies. You can't control traffic between machines on the same vlan. So for each the VLAN that you want to analyze, you will need to create a new vlan and divide the machines between the 2 VLANS.

  In your case with Native IOS, you are limited to only 1 pair of VLAN for InLine followed, but your desired deployment would require 20 pairs of vlan.

  The IPS 5.1 software now has the ability to manage the 20 pairs, but the native IOS software doesn't have the ability to send the 40 VLAN (20 pairs) to the JOINT-2.

  Changes in native IOS are in testing right now, but I have not heard a release date for these changes.

  Now cat BONES has already made these changes. So here is a breakdown of basic of what you could do in the BONE of cat and you can use to prepare for a deployment native IOS when it came out.

  For VLAN 10-20 and 300-310, you want monitored, you will need to break each of those VLANs in VLAN 2.

  Let's say that keep us it simple and add 500 to each vlan in order to create the new VLAN for each pair.

  Therefore, the following pairs:

  10/510, 511/11, 12/512, etc...

  300/800, 801/301, 302/802, etc...

  You configure the port to probe trunk all 40 VLAN:

  set the trunk 5/7 10-20 300-310 510-520 800-810

  (And then clear all other vlans off this trunk to clean things up)

  In the configuration of JOINT-2 create the 20 pairs of vlan inline on interface GigabitEthernet0/7

  NW on each of VLAN original 20 leave the default router for each LAN virtual vlan original to the vlan 500 +.

  At this point, you should be good to go. The JOINT-2 will not track traffic that remains inside each of the 20 VLAN original, but would monitor the traffic is routed in and out of each of the 20 VLAN.

  Due to a bug of switch, you may need to have an extra PC moved to the same vlan as the router if the switch/MSFC is used as the router and that you deploy with a JOINT-2.

• Configure two Ports on an ASA5510 with 2 different inside networks

  How can I configure two ports on an ASA5510 (version 8.4 (5)) or with 2 different inside networks out interface or two inside and two on the inside outside routing to an outside and inside another for the rest outdoors?

  Specifically, I had all three interfaces with dhcp and basic configuration of all, I got one (10.1.0.0) inside out successfully from the internet (208.83.73.193 for example), but I'm not sure of the second internal interface (192.168.1.0) out to the internet.

  I need VPN or any connection between the two internal networks.

  This is the basic configuration of may:

  interface Ethernet0/0

  nameif Internet

  security-level 0

  IP 208.83.73.x 255.255.255.240

  interface Ethernet0/1

  nameif inside

  security-level 100

  IP 10.1.1.1 255.255.0.0

  interface Ethernet0/2

  Guest Network Interface Description

  nameif GuestNetwork

  security-level 100

  IP 192.168.1.1 255.255.255.0

  Route Internet 0.0.0.0 0.0.0.0 208.83.73.206 1

  Route Internet 192.168.1.0 255.255.255.0 208.83.73.206 1

  dhcpd address internal 10.1.5.100 - 10.1.5.254

  dhcpd dns 10.1.2.7 10.2.1.200 internal interface

  dhcpd wins 10.1.2.7 interface internal

  interface of lease 432000 dhcpd internal

  field of dhcpd

  xxx.xxxxx.xxxx.gov

  internal interface

  enable dhcpd internal

  dhcpd address 192.168.1.2 - 192.168.1.50 GuestNetwork

  dhcpd dns 208.67.222.222 208.67.220.220 interface GuestNetwork

  enable GuestNetwork dhcpd

  network object obj - 10.1.0.0

  dynamic NAT interface (internal, Internet)

  I tried to configure nat for the guest network the same way that I have it set to the 10.1.0.0 network and also nat static and that it did not work (maybe I did wrong).

  If get this accomplished is possible I would very much apreciate a configuration example of what do I do

  Help, please

  I also found this two articles from Cisco that applies to the ASA Version 8.3 and I guess she could apply to Version 8.4 (5), please let me know if yes:

  http://www.Cisco.com/en/us/products/ps6120/product s_configuration_example09186a0080b7c939.shtml

  http://www.Cisco.com/en/us/products/ps6120/product s_configuration_example09186a0080b1ee95.shtml

  Thank you

  two inside networks to one outside is no different to a demilitarized zone and inside outwards. Both come from a security level higher and go to a lower level of security. In your case, there is the second inside network for guest users, I would use a lower level of security as the guest network is probably not as trustworthy as the internal network.

  The second requirement (two inside and two outside) would need a form of routing that the ASA does not support the way in which you want to use based on policy (there are some hacks with NAT, but it's really horrible). That you could use for this are security contexts. A context with inside1/outside1, the other context with inside2/outside2. Here, you can easily route traffic inside2 to outside2 and inside1 to outside1.

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• 6.2.16: when you try to update Itunes, I get the following error message: "there is a problem with this package of can I install."  A program required for this install to complete could not be run.  Contact your support team / packages vendo

  6.2.16: when you try to update ITunes on my Windows laptop, I get the following error message: "there is a problem with this Windows Installer package.  A program required for this teaching to complete could not be run.  Contact your supplier of staff or the package of support ".  There is no associated error code.  I've never had a previous issue with ITunes updates.  Thank you, Debbie

  Repair Apple Software Update since the programs & features Panel configuration and then try again.

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  The more information box has direct links with the current and recent if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit - for older video cards) as a workaround for problems with installation or operation, or compatibility with third-party software.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• What are the minimum system requirements for firefox 5 forMac OS x

  When you published Firefox 4, it updated automatically on my Mac PowerPC osx 10.5.x and then would not be executed. I had to look for an earlier version, download and reinstall. It was awkward. I can't find min sys req for the new 5.0 version. Min sys requirements should be obvious in yor press. What is the minimum configuration required for firefox 5.0 for Mac osx, and with more frequent updates, how will I know when you have 'obsolete' another one of my machines, and how would I be protected to an update too far?

  Firefox 4 and 5 will not run on a Mac PPC; only on Intel. You can get the TenFourFox, which runs on a PPC.

  http://www.floodgap.com/software/tenfourfox/

• technical requirements for download Lion 10.7.5 to Yosemite or Capitan operating system

  Hi, I have a Mac Book Pro 3 13 inches please, I would like to know the hardware configuration required for download Lion IOS 10.7.5 for Yosemite or Capitan, thanks¡

  Click here for more information.

  (140913)