Similar Questions

• Merge two of the same photo with applied different exposures

  I have a picture that I copied a couple of times and imported to LR. I've adjusted to the exposure of the sky in a single copy and then in the foreground in another. How to merge two photos to make the sky a as well as the first plan of the other?

  Combination of two images requires another program like Photoshop, Photoshop Elements, or some other software pixel editing program. If you have two different exposures to different contexts and use Lightroom 6 or Lightroom CC you have an option to use Photomerge and choose merge to HDR. But the part that there is no way to combine the two images using only Lightroom.

• Two ports in the NI 9401 module?

  Hi all

  I'm relatively new toLabView, but I have to say that I'm enjoying learnicg it. My problem is that I need to generate two independent signals with a connected NI 9401 module a OR cDAQ-9172.

  I need to generate a sequence of bits to control a demultiplexer, the sequence is 0000, 0001, 0010, 0011... 1111, 0000, 0001... So far, with the help of this great forum, I managed to generate the sequence, my problem is that I need to use the other bits to control the spindle enable (bit) of an another demutiplexers cascading.

  I read that the NOR-9401 is configurable nibble, so I understand that I could use bits 0:3 to generate the sequence and 4:7 bits to control bits allow for demultiplexers. But until now I could haven´t this task, I see all the 8 rows as a single port and I was not able to learn how to configure two ports as outputs time and generate different signals.

  I'm using LabView 8.6

  Could someone help me please in this task, I would appreciate any help really.

  Kind regards

  Joseph

  Hi Joseph,.

  I thought after studying the best way to do it, not with the crazy arry.

  Use the power level 2 - n = 4 and x being the u8. You can then wire the output for the upper nibble DAQ.

  Note: If you have placed a number of u8 to a data acquisition task configured for the 0 line - it will seek only to bit 0. It is the extension of what ever and the number of selected lines.

  

  Hope this helps

• VPN router to router with overlapping of internal networks

  Hello Experts,

  A small question. How to configure a VPN router to router with overlap in internal networks?

  Two of my internal networks have ip address 192.168.10.0 and 192.168.10.0

  No link or config will be appreciated. I searched but no luck.

  Thank you

  Randall

  Randall,

  Please see the below URL for the configuration details:

  Configure an IPSec Tunnel between routers with duplicate LAN subnets

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00800b07ed.shtml

  Let me know if it helps.

  Kind regards

  Arul

  * Please note all useful messages *.

• Sharing/synchronization via Dropbox catalogue with 2 different accounts of CC?

  A catalog may be shared/synchronized between two Mac separated via Dropbox with 2 different accounts of CC?

  Thank you.

  Lightroom is not designed to be multi-user. If a user tries to open the catalog before the update (synchronization) takes place the catalog may be corrupt. If a user closed the catalog until the synchronization is complete, the catalog may be corrupt. You take a big risk trying to work this way. Some users have reported success using the catalog in dropbox, but it is not recommended by Adobe. You yourself if you decide to go in this direction.

• How can I configure a port Ethernet NI9792 gateway to communicate with a cRIO CAP?

  Salvation OR engineers,

  I intend to use my gateway NI9792 in the following way:

  1. a single Ethernet port for network connection. That's how I'm developing, download the software and monitor my request through my PC in my office.

  2. the other port to communicate with a cRIO device? If so, how can I do it?

  It seems to be a stupid question, but I really couldn't work this!

  Thanks in advance,

  Luiz

  Good afternoon, Luiz

  Follow the first link to guide the module which can be used and other links to the best part of bore configuration CRIO. For any question, please contact us.

  How to set my time on the NI WSN-9791 or NI 9792 gateway server?

  http://digital.NI.com/public.nsf/allkb/44FA322FAFF8D58D862575BD00591A54?OpenDocument

  Configuration and NI WSN product guide
  http://zone.NI.com/DevZone/CDA/tut/p/ID/8710

  Configure the Ports of double Ethernet on real-time controllers

  http://digital.NI.com/public.nsf/allkb/67F94BB93BCE32CF86257367006B3659?OpenDocument

  video installation and installation CRIO

  http://www.NI.com/SWF/demos/us/cRIO/outofbox/

  Automatic configuration of network for the cRIO-9073 and cRIO-9074 CompactRIO controllers

  http://digital.NI.com/public.nsf/allkb/37C790309A210A748625757000570938?OpenDocument

  Sincerely,

  Mauro Vera.

• script to find VM with configured serial port

  I'm looking for a script powershell list all virtual machines with a configured serial port. someone has already written one? I looked at the health check and scripts of type I could find, but could not find a list of the serial ports on the inventory.

  Thank you

  Mike

  Try something like this

  Get-View -ViewType VirtualMachine | %{
       if($_.Config.Hardware.Device | where{$_.gettype().Name -eq "VirtualSerialPort"}){
            $_.Name
       }
  }
  

  ____________

  Blog: LucD notes

  Twitter: lucd22

• Configuring the Ports of premium?

  Hello

  I have a camera (9636) sbRio with analog inputs which I use to acquire data. In my Labview project, I have listed the chassis and FPGA, and connectors. If I click on, say, AI0, I can set the sensitivity of tension (1, 5 or 10 volts) and is it a single differential completed connection or referenced. All very nice...

  The question is this - for a differential measurement, you need two ports. The manual for the sbRio helpfully informs me that those who would be AI0 and AI7 port on my device. BUT if I configure AI0 to be differential, AI7 becomes automatically differential. In other words, I could quite happily put AI0 be differential, and when I look at the configuration of AI7 he says still unique reference ended.

  So, what I have to change each port pair to be differentiated or is - this auto (in spite of what properties tells me)? What happens if I updated AI0 5 volts, differentials and AI7 1 volt CSR? That I could do, but shouldn't be able to! I'm * really * changing the configuration of the ports in the Properties tab. There is also no option under MAX to set up the Council for the CSR or differential!

  Can someone explain?

  Hi Jimbo76,

  I'm a sales engineer for National Instruments. When you configure a sbRIO for differential analog inputs, you must right click on the appropriate channel positive (AI0 - AI7) in the Project Explorer and select Properties. From here, you can customize the configuration of the channel, which you can then save by clicking OK.

  It is important to note that even if the complementary differential channel is always visible (AI(n+8) for all HAVE (n)), it is not active and should be ignored. I hope this helps.

  Kind regards

• EA2700 - how to configure multiple ports

  The EA2700 is a router 4 ports (Ethernet) + WiFi.

  I want to configure the port forwarding, but the configuration screens won't let me set up several ports.

  It allows only an IP address to a transmitting device.

  I have an iMac and a Mac-mini two ethernet connected and a random collection of iPad/iPhone/printer, etc. WiFi devices.

  The Mac mini is a web server and is visible on the outside, but not to the iMac.

  The iMac can partially accessible by using the ip address of the mini (192.168.x.x), but while it displays the text on the page, none of the pictures show.

  I'm converting a Comcast Technicholor-modem/router WiFi to a surfboard 150 + LinksysEA2700.

  As far as I know, working directly from the iMac all connectivity works as expected, except for the mini.

  IF I disable the port forwarding, contact attempts are simply the prsented with the login to the EA2700 page.

  Normally you can not forward the same port of two different IP addresses.

• 2 service Consolen Ports with 2 different routed IPs

  Hi all

  I want to configure 2 Ports Serviconsolen with of different IP addresses. The two IP addresses are routed. Howe can I put different default gateway for this configuration.

  SConsole1: 192.168.1.x

  SConsole2: 10.1.1.x

  Thanks for any help

  Nautilus

  Hey,.

  It is not possible to have multiple GW.

  You must add a static route for that to happen.

  Take a look at the following Article: http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1005212

• How I fixed my USB ports not working not problem. Two ports left side previously does not... HP Dv7

  So I do not know what is not "where it will honestly, but put there just to try to help someone else who has struggled with this as long as I did it...» I ended up having my two USB ports on the left side (turned out to be my 3.0 ports) working again when they recognize nothing. I could use the USB 2 on right 2.0 ports, but the transfer rate was terrible.

  My answer on another question where someone had a similar problem... good luck!

  'Hi. '

  Not sure if this will help, but I had the same problem, the two ports on the left did not work on my Dv7. All this time I thought that the USB on the right were my 3.0 ports so I thought that would be nice, but it's been over a year that I initially had this problem and made a bunch of maintenance of the system meant that I would look through it again. In any case, I went to the Device Manager through the computer management tool. I know that you can go straight to the Device Manager, but just give you exactly how I did it. You can search just to start computer management.

  So I chose Device Manager in the menu on the left side and it looked like ordinary Device Manager. Went down to Universal Serial bus controllers... at this stage, I watched the action menu on the right and select more actions, opinions and you click Show hidden devices. After that I went through my USB controllers one by one as I had done many times before and checked them, tried the update of drivers, etc... Under the USB controllers Section, I noticed something like xHCI Host controller of compliance Test... I right click it and went into its details, I tried the driver updated and installed the new driver. 2 new USB controllers immediately arises: Renesas Electronics USB 3.0 Host Controller and root hub.

  Switched on a test drive from the right thumb to the left and the computer instantly recognized and installed the driver for the stick.

  And that was all... hope it helps even if this is later. "

  Hi @klark1kent,.

  Thank you for visiting the Forums Support HP's, welcome and thank you for the important information.

  Have a good week.

  Thank you.

• How to configure two programmers process?

  Good day to all! I have Oracle 10 g coupled with PT 8.50.14 and using MFC 9.1 on Windows 7 32-bit. I started with a CRP PSNT, but decided to create a new PRC PSNT2. I designed each CRP to run recurring processes (i.e. purging). Currently I encounters an error with the RTC (master CRP) because it will not perform the recurring process, but the other CRP (PSNT2) works very well. Interesingly enough, until PSNT2 came on the scene, PSNT worked functionally. He produced all of the said duties. Then configure two PRCS to work functionally? Be blessed

  There is a bug with the tools 8.50 and the PSAESRV:

  https://supporthtml.Oracle.com/EP/faces/secure/km/DocumentDisplay.JSPX?ID=1082697.1&h=Y

  This problem was caused by a combination of database bug/problem and a problem of peoplesoft on process on PeopleTools 8.50 and above PSAESRV.

  A workaround for this problem is to disable the separate Application Engine Server. PSADMIN to start and set the desired process, when configuring Scheduler, it will ask you if you want to create separate application engine servers. In this step, you answer with N (no). Here is a comprehensive guide with steps on how to proceed:

  https://supporthtml.Oracle.com/EP/faces/secure/km/DocumentDisplay.JSPX?ID=659343.1

  The impact of this deactivation is minimal and Oracle explains why in this document id:

  https://supporthtml.Oracle.com/EP/faces/secure/km/DocumentDisplay.JSPX?ID=651970.1

• Re: Portege R600 - port replicator is compatible with regional products?

  Community of greetings from Toshiba,

  I need to buy laptops for several employees who are moving between the United States, the United Kingdom and the Middle East.
  The Portege R600 exist in all 3 markets, but each has a slightly different part number.

  The part number Replicator of compatible Port to the R600 is difference to the United Kingdom, the United States and the Middle East.
  Users would be able to dock their laptops in one of the 3 offices, because they travel extensively between each country.

  What's the Slim Port Replicator II (PA3603U-1PRP) and Slim Port Replicator III (PA3681E-1PRP) compatible with each of the products of the soil of Portege R600?

  United Kingdom Replicator of ports Slim Portege R600-11B (PPR61E-01G00CEN) III (PA3681E-1PRP)
  Middle East Replicator of ports Slim Portege R600-10 b (PPR61E-00F00MAR) 2 (PA3603E-1PRP)
  USA, Portege R600-S4201 PPR60U - 01700C Slim Port Replicator II (PA3603U-1PRP)

  Someone has an experience buy Toshiba products in the Middle East? Or needed to use Docking Stations in offices in several countries?

  Thanks in advance,
  Ted

  (I posted a similar request in the Forum we and receives no answer - http://laptopforums.toshiba.com/t5/Port%C3%A9g%C3%A9-Laptops/Port%C3%A9g%C3%A9-R600-US-UK-Middle-East/m-p/32060#M489)

  Post edited by: TedRNelson

  Hello

  I think that it shouldn't be a problem with the different Portege R600 in combination with the Slim Port Replicator 3.

  Portege R600-11b, R600-10 b belongs to the same series (PPR61E), that the R600 US belongs to the PPR60U, but this should t be a problem.

  As far as I know the different R600 from different regions are not really different (some belongs to the same series) as far as I know there could be a difference between some pre-installed applications and some modules as for example the card wireless network, but this should not affect the use of Slim Port Replicator 3.

  Cheers mate

• How to configure two USRPs as a MIMO transmitter to transmit the PRS modulated sequences?

  Hello.

  I am transmitting two orthogonal sequences using USRPs with Labview or GNU. The sequences have three levels (+ 1, -1, 0). I thought by using the method of partial response signaling (similar to the BPSK modulation) to modulate their. Is it possible to do?

  Even if you can help me to transmit a modulated signal BPSK or QPSK, using two USRPs conencted with cable MIMO, it will be a huge favor.

  Thank you

  Sam.

  sam2013ni,

  Here is a National Instruments KnowledgeBase article that explains how to use the toolkit modulation of the data defined by the user. Please try using this and see if this is useful.

  http://digital.NI.com/public.nsf/allkb/65790619262D402B86257260000C912D?OpenDocument

• Ran Malwarebytes & two threats were each one with the same name: PUM. Disabled.SecurityCenter. fact that associated with MSSE PUM & the boxes unchecked in MS security Center.

  Original title: PUM. Disabled.SecurityCenter

  I recently removed "patch system" of my Dell computer XP. Malwarebyte s was the only software to do. MSSE caught, but couldn't fix it. I then updated & ran MSSE on my Toshiba - no threats not found. I then ran Malwarebytes & two threats were each one with the same name: PUM. Disabled.SecurityCenter both at the Date of the registry in HKLM\SOFTE\Microsfot\SecurityCenter\AntiVirusDisableNotify & HKLM\SOFTWARE\Microsfot\securityCenterFirewallDisableNotify.  These two have been listed bad: Good (0) (1).  In the Malwarebytes wesite, I read that this has something to do with MSSE. In a commentary, he says it occurs if, in the MS Security Center, the notification "Notify me if my computer might be at risk because of my virus protection software settings" is unchecked.  I then went ahead & check all 3, firewalls, viruses & automatic updates. My computer seems to work well, except that the fan runs all the time (there are a lot of processes running & the CPU usage is very--often 100%, but the computer works fast).

  My questions are: 1) the PUM associated MSSE & the boxes unchecked in MS security Center; (2) should I click on "ignore" in the Malwarebytes scan? 3) was right to check all the boxes in the center of security - "altert me if my computer may be at rist b/c of my xxx software settings?  Thanks in advance for your help.

  PC fan2

  Hello

  (1) is associated with MSSE PUM & the boxes unchecked in MS security Center;

  The following thread might answer this question: http://forums.malwarebytes.org/index.php?showtopic=69859

  (2) should I click on "ignore" in the Malwarebytes scan?

  Yes

  3) was right to check all the boxes in the center of security - "altert me if my computer may be at rist b/c of my xxx software settings?

  Only, run antivirus software at the same time. Firewall must be performed, evil-ware bytes can be run at your pleasure.