Configure the port error: resource in use

Similar Questions

• When I tried the update of lightroom cc2015 I get a U44M2P7 error message. I tried to rename the file update and a new attempt and also update manually but still the same error. I use a mac with os x El Capitan version 10.11.3 any suggestions would be gra

  When I tried the lightroom cc2015 update I get an update of the failure U44M2P7 error message. I tried to rename the file update and a new attempt and also update manually but still the same error. I use a mac with os x El Capitan version 10.11.3 any suggestions would be greatly appreciated.

  U44... Update error http://forums.adobe.com/thread/1289956 can help

• HP Officejet Pro 8600 no possibility to configure the Port

  My OS is Win 8.1 (last version), latest version of the printer driver, last wizard to install printers used.

  My first printer "HP Officejet Pro 8600" folling down on the issue of the screen. I'm doing a swap with the same model, I have to uninstall and reinstall the full with Wizard, now I have some difficulties to recognize the printer.

  -Shortly, no communication!

  -A few times, printing find after printer communication error.

  If I go to "Properties/Port/port" I got "Error Message.

  > An error occurred during port configuration.

  > The file name, directory name or volume label syntax is incorrect.

  Could be a former key stay in the registry (with the old link to the printer)

  I have to uninstall and reinstall the wizard fuul without success.

  Now the analysis feature does not run and printing run with delay.

  Major Remarq:

  I have no problem with MAC OS 9.x to 10.10.1

  Thank you very much in advance for your support

  Hello

  The port must not be changed that way but through the HP software, it is managed by the software and such a mistake is planned during the attempt to change the port...

  Try opening the HP Officejet Pro 8600 software, and then click the Utilities.

  Click Update IP address and type the IP address of the printer, which can be found by clicking on the icon wireless/network at the top of the Panel before you the printer.

  Click on save and confirm, then close and reropen the HP software,.

  What happens when you try to scan now?

  It'll work, or is there a specific error or behavior?

  As well try now the doctor of printing & scanning HP, it is listed under the Utilties batn so, follow the steps on the screen by selecting the difficulty of analysis and let me know the results if you are still having problems.

  Shlomi

• Unable to connect with RDP after you have configured the port forward

  I have configured my router with port pushing forcefully with port 3389. Now when I try to rdp to the pc from outside I get the following error:

  Remote Desktop cannot connect to the remote computer to one of the following reasons:

  1. remote access to the server is not enabled

  2. the remote computer is disabled

  3. the remote computer is not available on the network

  I checked that all these 3 does not apply to me. I was able to RDP pc (with the local ip address) from another pc in my network home but not from outside. Could someone help me please?

  Is the computer on which you want to connect with Remote Desktop [DRC], IE. the DRC, by using a host address static IP on your LAN? In the contrary case and the computer is restarted its possible its LAN IP address changed by denying any plan of port forwarding you set up in your router. Go to the site CanYouSeeMe and host DRC computer test.

  http://www.canyouseeme.org

  Also, when the connection to make sure that you really test from a client outside the DRC and does not use the public IP address of the router from a local computer on your local network.

  http://theillustratednetwork.MVPs.org/RemoteDesktop/TroubleshootingDiagrams/Basic.html

  Finally you are sure that the public IP address of the router has not changed? If you have a dynamic IP from your ISP, you can use a free as no - IP.com that maps a name to your public IP address. Call using the fully qualified domain name. Many routers support which is a free service like DynDNS for example. You can also download and install a small program on the host of the DRC. The program communicates with the No - IP or DynDNS servers on a regular basis. The server so you know what your current IP address and that map to your fully qualified domain name.

  http://www.no-IP.com/?utm_source=MSN&utm_medium=CPC&utm_term=no%20IP%20.com&utm_campaign=brand+MSN

  http://dyn.com/DNS/

• Configuring the Ports of premium?

  Hello

  I have a camera (9636) sbRio with analog inputs which I use to acquire data. In my Labview project, I have listed the chassis and FPGA, and connectors. If I click on, say, AI0, I can set the sensitivity of tension (1, 5 or 10 volts) and is it a single differential completed connection or referenced. All very nice...

  The question is this - for a differential measurement, you need two ports. The manual for the sbRio helpfully informs me that those who would be AI0 and AI7 port on my device. BUT if I configure AI0 to be differential, AI7 becomes automatically differential. In other words, I could quite happily put AI0 be differential, and when I look at the configuration of AI7 he says still unique reference ended.

  So, what I have to change each port pair to be differentiated or is - this auto (in spite of what properties tells me)? What happens if I updated AI0 5 volts, differentials and AI7 1 volt CSR? That I could do, but shouldn't be able to! I'm * really * changing the configuration of the ports in the Properties tab. There is also no option under MAX to set up the Council for the CSR or differential!

  Can someone explain?

  Hi Jimbo76,

  I'm a sales engineer for National Instruments. When you configure a sbRIO for differential analog inputs, you must right click on the appropriate channel positive (AI0 - AI7) in the Project Explorer and select Properties. From here, you can customize the configuration of the channel, which you can then save by clicking OK.

  It is important to note that even if the complementary differential channel is always visible (AI(n+8) for all HAVE (n)), it is not active and should be ignored. I hope this helps.

  Kind regards

• I get the ox8oeeoooc error when I use my webcam.

  I get error ox8oeeoooc everytime I use my webcam
  Can someone help me

  Hello

  ·         What is the exact error message you get?

  ·         What operating system is installed on the computer?

  ·         What is the brand and model of laptop/webcam?

  I suggest to run the troubleshooter of material and to check if it helps.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

• Something similar to groups of objects, but for the ports? (must be used on an ACL)

  Hello community!

  I'm fairly new, when it comes to firewalls, but I have some experience with routers and switches, so I'm not completely lost.

  Practically, we all know that a group object is a large bucket to throw things and then managing them as a single group, which is very useful for many reasons... so is there something similar that we can use in an ACL for the port?

  Say so, let that I want to allow the following ports:

  • 80
  • 443
  • 25
  • 30500
  • 20500
  • 8080
  • 14600
  • 21
  • 753
  • 22

  And instead of doing something like this:

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 80

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 443

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 25

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 30500

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 20500

  access-list extended dmz_access_in permit tcp host WEB host WEB-EXT eq 8080

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 14600

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 21

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 753

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 22

  do something like:

  dmz_access_in list extended access permit tcp host WEB host WEB-EXT eq PORT_LIST1

  Thank you!!

  PD: Excuse me if some port above are not TCP, if just one example. I just start typing all the numbers that came to my head.

  Hey Rolando,

  On a SAA, you can combine services and protocols based on the source/destination in an object-group service oriented. Your example would look like this:

   object-group service PORT_LIST1 service-object tcp destination range 21 22 service-object tcp destination eq 25 service-object tcp destination eq 80 service-object tcp destination eq 443 service-object tcp destination eq 753 service-object tcp destination eq 8080 service-object tcp-udp destination eq 14600 service-object tcp destination eq 20500 service-object tcp destination eq 30500

  You can create also integrate groups:

   object-group service WEB_PORTS service-object tcp destination eq 80 service-object tcp destination eq 443 object-group service PORT_LIST1 group-object WEB_PORTS service-object ...

  This type of group is going where the Protocol is specified in the ACL:

   access-list dmz_access_in extended permit object-group PORT_LIST1 object HOST object EXT-WEB

• trying to create an ESXi data store on the local drive.  Configuring the host error: unable to update the disk partition information

  I'm a newbie on ESXi and don't know what it takes to get ESXi correctly partition my drive SATA 500 correctly.

  I will implement a laboratory unit to carry out tests for ESXi and ESXi is not quite correctly the disk partitioning or do not see a good partition in order to create a data store.

  This system was able to correctly identify and configure a data store on a small 80 GB seagate SATA disk, however, this isn't quite enough storage so I swapped the hard drive and tried to re - install ESXi on the new hd.

  I use a USB boot ESXi since and it is launched and configures the card intel pro1000 pci ethernet correctly.  also correctly the id of the cpu and memory.  everything seems fine and he is even able to see the hard drive.

  Here are some screenshots of the process that I go through to make my data store...

  on this photo-sous the column titled 'available' is 'none', also said, under the title 'san identifier' he said 'not applicable' - I guess that's not quite right?

  

  

  

  

  and disappointment - failure?

  

  I tried to go into the bios if there are some settings I need to do to get this hard drive set up... I don't understand enough about ESXi to find out why the drive is not found and configured correctly.  is this a bios problem w / my system or a problem of ESXi?

  pls help!

  You have generally not, but it might be interesting to start with something like a Linux live CD and then using gparted or other to wipe all the top partition information.

• Manually configure the client 11 essbase (without using the Installer)

  Hi all
  
  is it possible to install the Essbase 11 client without using the installation program?
  I tried to copy the 'bin' and 'regional settings' directory of an existing facility and put in place the variable of environment ARBORPATH - without success.
  
  I missed something? Maybe some registry entries? Or is it not possible to manually configure the essbase client?
  
  Any response would be appreciated.
  
  See you soon,.
  Martin

  In 11.1.2.x, you can get a separate installer for essbase spread spreadsheet add-in.
  Simply, you can run that as we do in version 9.

• How to configure the Windows speech recognition and use gtalk and gmail?

  Original title: Windows Vista speech recognition program the

  Trying to learn how to use the program of recognition of the window so that I can help a friend who has very high served as his hands. I'm getting the hang of it, but I need to know how to use Windows RV with gmail, because that's where we have been typing his e-mails for him, and is where he'd like to read his mail. On my own page of gmail, I am able to use the "numbers" for everything except actually typing in the main field, where he would actually type emails. Anyone able to help?  Max of TIA

  Hello
  • What happens when you click on the text box and dictate?
  • Also, try to use the HTML version of gmail and check.
   
  1. in Windows vista speech recognition.
  I've collected some articles from the Microsoft Knowledge Base that will help you in until the speech recognition settings.
  Windows speech recognition
  http://www.Microsoft.com/enable/products/windowsvista/speech.aspx
  Set up speech recognition
  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-speech-recognition
  Setting speech options
  http://Windows.Microsoft.com/en-us/Windows-Vista/setting-speech-options
  What can I do with speech recognition?
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-can-I-do-with-speech-recognition
   
  2 on the use of speech recognition on gtalk you can ask your question on the forums of gtak. Here is the link.
  Voice and video Chat
  http://www.Google.com/support/forum/p/chat/label?lid=18819d87e4369fa5&hl=en
   
   
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Automatic use at the request of resource blocks using not all solutions available resource locking

  Hello

  I'm trying to use TestStand with batch process model. I run lots of 8 EHR. Most of my tests have dedicated hardware, some use shared resources. As far as I can tell (and according to support NEITHER) the fastest way to run my test is to configure all tests in blocks using Auto demand for resources and just create enough resource Lock Alternatives for EHR 8 to use resources dedicated at the same time.

  If I create a single block of resources at the request of self employment with Alternatives to resource lock 8, it works perfectly. All EHR 8 run the test at the same time. However, if I add a second block of resources at the request of self employment with 8 Lock Alternatives resource (the same as in the first block, or with new unique names named) TestStand uses 4 of 8 Resource Lock Alternatives and my test takes twice as long as it should.

  Is it possible that I miss a setting, or configuration things wrong? I have attached a simple sequence that illustrates what I'm trying to do and a capture screen how TestStand runs it. TestStand 2014.

  Thank you very much for the help!

  Will be

  I can't reproduce your behavior.  I have a quad core with all discussions on "logical".  So a total of 8 wires.  I modified your movie file to do 16 DUT to see if she could slow down.  I see about 7 seconds per report.

  We know that this is not the sequence file, because I run your movie file.  My guess is that there is another setting somewhere.  TestStand or in your operating system that is the cause.

  You have changed the model of batch processing?  I use out of the box one.  What version of TestStand?  I have 2014.  In Options of Station > preferences what is your processor affinity set?  Mine is - 1.

  Kind regards

• Configure the session error # BFFF800B

  I have a camera of Dalsa CR-GM00-H6400 model.  It's a GigE camera.  I have configured and used other Dalsa cameras on this system, but this camera gives me a session configuration error as soon as I click on it.  Dalsa Viewer works very well.  The camera hangs up and talking.  I can ping.  Why NOT-IMAQDx will not start a session?  I use the labview drivers supplied with my 2011 version and I also have the last vision development module.

  I also have a model of camera Balser Scout SCA640 - 120gm which the image appears as a 641 X 494 pixels giving an inclination of the final screen.  Is it possible to change this OR-IMAQDx observer in MAX.  I have not tried this in the vision module yet because of the weak results in MAX made me switch cameras and then I found the problem described above.

  Good,

  Tell me where the files are stored was the winner.  I found there were only 2 files for the HM640 the .iid and .xml the .iid had no camera file.  This is because the XML file has a bad line in.  When I deleed the camera I found that the file reappeared with the lines of the bad asme. I guess it is downloaded from the camera.  I went on the site of dalsa and downloaded another version of the XML file and replaced the one downloaded.  Bingo.  Then, there was also an everythingworked of .icd file.  Thanks for the tips.  This BFFF800B error was apparently due to the wrong line in the .xml file.  I'll go to Dalsa with this problem and see if they still have a bug in the firmware.  Thanks for the help!

• How to configure the port to connect the SG300 switch to 3com switch

  Hello

  I need help. I have my network with multiple switches SG300.

  I have one of them as my base switch working mode layer 3. With 2 VLANS and vlan interfaces to each vlan.

  Everything works ok.

  But now I need to plug a 3com unmanage switch who welcomed of vlan 1 and 2. How can I connect this switch to my Cisco sg300 switch? Which mode to use in this port?

  Thank you very much.

  SG300 Switch L3

  I have

  I have

  SG300 L2 switch

  I have

  I have<-------- how="" should="" i="" configure="" this="" connection="" to="" support="" all="">

  I have

  3Com unmanage switch

  I          I

  I          I

  I have vlan 1

  VLAN2

  Use of VLAN based on MAC on SG300 L2 switch, record all customers on the required VLANs (or better configure port SG300 L2 to 3com in VLAN PVID with maximum and other clients in the VLAN based on MAC).

• I want to manage my web isa with isa server management.help me how do I make and the port that should be used?

  I have an isa Server 2006
  I want to use the vpn connection and and limit internet access bandwidth:
  1. suggest a pdf for learning about this
  2 - to use web isa management utility which port should I use?

  Ask in the forum ISA Server:

  http://social.technet.Microsoft.com/forums/en-us/Forefrontedgegeneral/threads

• Configure the backup error Windows7-64

  Error code (the Server execution failed (0 x 8008005) we tried with this forum, but nothing suggested worked 7 months.)  We decided to wait a while to see if there is more on this problem. MS tried at the time, but they had no idea either.

  We will listen to all suggestions and will try new ones we have several pages of suggestions.

  Hi Rob_Gr,

  Check the status of the Volume shadow copy service and Windows backup service in the services window. Use the following steps to check:

  i. click on start and type services.msc in the search box

  II. the service search

  Make sure that the startup type is automatic. Steps to set the auto services

  III. the service search

  IV. right click on the service

  v. If the service is stopped and then starts the service

  VI. Select Properties

  VII. and in startup type, select automatic

  Try the following steps:

  i. click on the round of departure.

  II. in the search box, type CMD.

  III. right-click on cmd.exe and select run as administrator.

  IV. Enter your password if prompted.

  v. at the command prompt, type:

  net localgroup "Administrators'"NT Authority\Local Service"/ Add

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.