Configure the question vSphere "alarms".

Similar Questions

• We have configured replication vsphere in our environment and when replication is triggered according to the OFR start us below the questions on the virtual machines that are configured for replication

  Question: We have configured replication vsphere in our environment and when replication is triggered according to the OFR start us below the questions on the virtual machines that are configured for replication.

  Version for esxi: Patch 5.1 level 7

  Virtual center of version 5.1

  Source of storage - IBM v7000

  Destination storage - Hitachi

  
  Questions:
  Events of breach RPO
  Consolidation for the VM disk failure
  Delta abandoned events
  Time change events
  NTFS error and warning (event ID: 137, 57)
  RDP disconnect and ping does matter
  Standby error
  Volsnap error
  Stop the server and offline issue
  Install vmtools emits automatically

  well, in this case, we need to disable the standby of the end of the replication.

  So that everything in triggering replication does not trigger the snapshot of the suspension.

  Then test the if you get these errors.

• How to configure the options of oracle community such as, I see the answers to the questions posted by myself in a separate stream of data/place?

  Hello

  Thank you for your initiative on the oracle community.

  I love the community and wants to play an active role.

  However, I see the discussions initiated by me in a separate stream of data/place rather than mix them in all the other debates.

  is it possible to search all discussions posted by me only in one place?

  Is it possible to configure the options so that only the answers to my questions will be displayed in the Inbox?

  It used to work before, however, I subscribed to a few communities and my Inbox is bombarded with all the discussions. I read and try to answer on the other discussions, but it is difficult to keep track of discussion initiated by me?

  Help, please.

  Its there in your profile

  user10163762

• Fact the VMware vSphere: install, configure, manage [4.0] class eligible for VCP5 prereq?

  Hi all

  Doing some research, but has not been able to confirm.  Also left message with our VMware training rep areas last week, but never heard back, so thought I would try here.

  In 2011, I finished the VMware vSphere: install, configure, manage [4.0] courses.  I never did get my VCP4, but now want to try for my VCP5.  This class would qualify as a prereq so that I can just take the VMware vSphere: What's New (version 5.0) courses?  The web site called specifically need to VMware vSphere: install, configure, manage [V4.1] class so I think not, but I wanted to check.  I would take the shorter, which is the new class rather than a class 4 or 5 days on vSphere 5.0 so I can.

  Can anyone confirm?

  Thank you

  Bob

  No problem, this path has always been available for VCP5.

  And Bob, the counties of 4.0 class, as well as class 4.1 - is only the class 4.1, which is referred to as the class 4.0 retired some time ago and has been removed from the page VCP5 when he retired.

• Cannot configure the firewall using vSphere client (access to ESX 4i)

  I can't acess the firewall by using the client vSphere connection to a host of 4i ESX.  I select the host & gt; configuration & gt; Safety profile & gt; and it flashes firewall briefly, but then watch as services (two) (VMware vCenter Agent (arrested) and NTP daemon (started).

  Clues?  I restarted services (and the host itself).

  ESXi should be behind a firewall because there is no firewall integrated its own.

  If you find this or any other information useful or appropriate, please consider giving points.

• Network connectivity error when you configure the server for vSphere

  I've just set up my first hypervisor, and naturally it became painfully obvious how much I have to learn.

  I met a problem that I don't know how to fix. When you configure the server, I have configured network settings manually in order to give him the good gateway, subnet mask and static IP address. Unfortunately, I still get "Failed" when I ping the DHCP server. ""

  Hope that the community will be able to guide me in this problem. I am sure it takes to understand this, so let me know what is needed and how to get more information. Thank you!

  Find the person who is responsible for the management of the switch and check which port is set to for example the VLAN you need. Depending on your setting of the port must be configured as an access port or a 802. 1 q port if you configure the VLAN ID on the ESXi host

  André

• Snooze configurable time & editting custom alarms

  like the dashboard, but there are a number of oddities of alarm boring. First is the rehearsal time. It is located at 5 minutes. It's really short. Is it possible to allow configurable snooze time? SNOOZE is usually 10 minutes... How to set the time of repetition as a custom alarm options? Also, when editting an existing custom alarm, you must go through all the steps to obtain the Finish"" button. It's a lot of work if you wanted to do was to change the time of 09:00 to 08:00. When can editting, you put a button "Done" on the time step (or on each step) so that the user can enter and exit as quickly as possible?

  Hi everyone, thank you for your patience as we continue to add more features on the dashboard, it comes out a configurable SNOOZE through the update of firmware this month here.

  SNOOZE, it was only half of the question but... How alarms configuable end like the chumby to put your device in night mode and day or change the channels from chumby of time?

  Who will be included?

• 8.0 questions about alarms

  Test 8.0 and really like the performance so far. I get this message in the console and can't find any doc respond to this message. Has anyone else got this with 8.0 before I go and open a ticket. Is there a task to do this?

  The number of alarms stored in the Foglight database exceeded 10000.0. There is more 35456,0 alarms have been cleared for more than a week. Please consider compensation.

  Message and help

  Hello

  I think that this is related to the following (I copy and paste part of the text).

  Motivation	A lot of the information presented in the browser interface is derived from alarms (alarm counties, States of topology objects and so on). If the rules are configured in evil, this can lead to the creation of a very large number of alarms within the system. The server is a default limit of 10000 alarms which can be displayed and used to calculate the States of objects. When the Server enforces this limit, it gives preference to the current alarms so that objects are presented in the correct state.
  Symptom	Browser interface performance is poor (that is, it responds slowly), in particular when displaying the table of alarms.
  Diagnosis / audit	The server is not overloaded and is still in processing. CPU utilization on the server is high it provides alarm information. Threads may clog for a few seconds, intermittently, when you attempt to load the alarm details.

  It is not only a question of performance Foglight it is also a question of ' can you really manage an environment that has so many alarms?
  You probably want to clear alarms.
  You can also change alarms by individually turning off loud alarms, change of thresholds or disabling levels of warning alarm (different environment to run with different settings and parameters of the box may correspond to some but not all environments.)

  You can also go to the VMWare environment dashboard > Administration (tab) > Set alarm Sensetivity level and switch to critical alarms.

  

  I hope this helps.

  Golan

• HA is located on the hosts; If the server vSphere is unavailable HA will always continue to work?

  Hello, I found the following question on the page Simonlong and I was sure it was incorrect.

  Which of the following are valid reasons for the deployment of vCenter Server on a virtual machine (choose 3)?

  A. vCenter Server must be deployed as a VM to migrate using VMotion

  B. vCenter Server must be deployed as a virtual machine to support the recovery by using the Site

  Recovery Manager

  C. vCenter Server must be deployed as virtual machines for joining a group Linked Mode

  D. vCenter Server must be deployed as a VM to be protected by a high availability

  E. vCenter Server must be deployed as a virtual machine to support using vCenter data

  Recovery

  Answer: ADE

  I didn't know that d was correct.

  So my question is, when HA is located on the hosts; If the server vSphere is unavailable HA will always continue to work?

  VMware HA is intalled on the side of ESX and can also operate without vCenter Server.

  vCenter Server is required to configure each host for HA, but then (per HA) is not necessary.

  André

• Satellite A200-1AE: How can I configure the settings of buttons Dual Mode Pad?

  Hello

  I recently bought a Satellite A200-1AE. I tried to configure the default first button on my touch pad (lower left) so that I can fire up MSWord, but it did not work.

  Now every time I have set the mode button and press this button, that nothing not to pass - I lost practically this button.

  My question is how can I configure the mode button on the touch pad settings? Even if I was able to start a program by using the 3 buttons how can I modify these programs?

  Thanks for your help!

  p.s. I read the extended version of the manual for my laptop. There is no explanation of my problem - it says I should look "Synaptics Dual Mode Pad properties.

  I don't know where are these properties.

  Hello

  It s is not so difficult as you think, the properties of the synaptics are in the "mouse properties" of your "Control Panel" of windows. When you reach the 'mouse', then click on the "Advanced" tab and you should find a button 'Advanced functionality settings'.
  It could be that the button is not named as mine, but it must be identical.
  After clicking on it, you should look for this 'easy' Launcher in one of the tabs.

  I think that you will make it, but I'd like some feedback from you.

  Welcome them

• Configuring the Ports of premium?

  Hello

  I have a camera (9636) sbRio with analog inputs which I use to acquire data. In my Labview project, I have listed the chassis and FPGA, and connectors. If I click on, say, AI0, I can set the sensitivity of tension (1, 5 or 10 volts) and is it a single differential completed connection or referenced. All very nice...

  The question is this - for a differential measurement, you need two ports. The manual for the sbRio helpfully informs me that those who would be AI0 and AI7 port on my device. BUT if I configure AI0 to be differential, AI7 becomes automatically differential. In other words, I could quite happily put AI0 be differential, and when I look at the configuration of AI7 he says still unique reference ended.

  So, what I have to change each port pair to be differentiated or is - this auto (in spite of what properties tells me)? What happens if I updated AI0 5 volts, differentials and AI7 1 volt CSR? That I could do, but shouldn't be able to! I'm * really * changing the configuration of the ports in the Properties tab. There is also no option under MAX to set up the Council for the CSR or differential!

  Can someone explain?

  Hi Jimbo76,

  I'm a sales engineer for National Instruments. When you configure a sbRIO for differential analog inputs, you must right click on the appropriate channel positive (AI0 - AI7) in the Project Explorer and select Properties. From here, you can customize the configuration of the channel, which you can then save by clicking OK.

  It is important to note that even if the complementary differential channel is always visible (AI(n+8) for all HAVE (n)), it is not active and should be ignored. I hope this helps.

  Kind regards

• Configure the search box on My DataFinder with vbscript

  Hello

  I use the following vbscript script to load data into data tiara Portal:

  Define dataFinder = Navigator.ConnectDataFinder ("My DataFinder")
  Set queryForm = Navigator.CreateQuery (eAdvancedQuery)
  queryForm.ReturnType = eSearchFile
  Call queryForm.Conditions.Add (eSearchFile, 'name', '=', '*.tdm')
  dataFinder.Search (queryForm)
  Set dataFinderResults = dataFinder.Results
  Call Navigator.LoadData (dataFinderResults).

  This works great until My DataFinder of research area was previously set through the control panel of Navigator DIAdem.

  We leave the tiara of a Visual c# application and the above vbscript part a vbscript script that is spent in DIAdem when it is launched through the argument of /CScriptStart.  I would like to define dynamically the DataFinder My search box a path argument also happened in DIAdem.

  Is it possible to configure the search box on the My DataFinder with vbscript?

  In addition,

  Is it possible to have the tiara run in the background without going through the DIAdem screen flash when it starts first?

  Thanks a lot for any help

  Renette

  Renette salvation,

  From DIAdem 11.1, newly released last July, we now have an interface of VBScript to define the areas of research and other aspects of the DataFinder.  DIAdem 11.1 also has the ability to save a configuration file DataFinder and load, both interactively and programmatially.  Earlier versions of DIAdem had no affect by program areas of research.

  Note that defining the areas by programming research will result immediately in all files being indexed and ready to be questioned - which can take some time after you set the new areas of research, according to the number of files in each search box, you add.

  You start currently tiara with a BACK extension to run a VBScript script right after the launch.  The advantage of this approach is that Sophie persists as an independent application, even after the end of the calling application.

  You may also call one of the two servers ActiveX of the tiara, which would invisibly begin DIAdem and allow you to stay in touch with this instance of tiara and read the DIAdem variables and run more DIAdem orders or VBScript scripts.  The disadvantage of this approach is that if your calling program ends, so does the connection ActiveX, and stops the instance launched by this connection ActiveX DIAdem.

  Ask if you have any other questions,

  Brad Turpin

  Tiara Product Support Engineer
  National Instruments

• Configure the second channel of TDS 2012 scope

  Howdy,

  Our laboratory has recently acquired a range of Tektronix TDS2012 dual channel and I'm getting so he can play nice with Labview 8.5. I downloaded the plug-and-play drivers and the accompanying screw sample without problem. I connected the scope via a GPIB-USB-HS adapter. PC running Win2k.

  The screws of the sample and some of my creations seem to be great with the exception of a question to work. I can't for the life of me get the vertical scale on the second channel to do what I want. When I use "Example VI" of the driver and set the Volts/Div to anything for a reading of CH2, changes the CH1 setting (?), it does indeed read CH2. I can't find where I could adjust the parameters of CH2 regardless... the vi "Set up display" seems to be independent channel.

  Any thoughts?

  Kind regards

  Matt Pausley

  North Carolina State University

  Hi Matt,

  I just downloaded the Tektronix TDS 200 1000 2000 project series Style Driver of instruments here, and there is no screws with the word "vertical" in them.  To make sure that you use the style of the project pilot, go to C:\Program NIUninstaller Instruments\LabVIEW 8.5\instr.lib\Tektronix TDS 200 1000 2000 series and confirm that there is a file of Tektronix TDS 200 1000 2000 Series.lvproj it and that the screws are in folders, not a Bachelor's degree in law.  The VI that you will use to configure the vertical range is Set up Channel.VI.  Pay close attention to the VI and control documentation.

  See you soon,.

  NathanT

• How to configure the LDAP connector in windows server 2012 R2 Active Directory?

  How to configure the LDAP connector in windows server 2012 R2 Active Directory?

  Hello

  Please post your question in Server TechNet Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• How do I configure the iPad2 to synchronize the iPad-Mailclient with Exchange 2010 via Active Sync using the certificate SSL client and name of user and password?

  Active Sync iPad ssl Client certificate

  How do I configure the iPad2 to synchronize the iPad-Mailclient with Exchange 2010 via Active Sync using the certificate SSL client and name of user and password?

  Hi Ewoki,

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the TechNet Exchange forum. Please post your question in the Forums TechNet in Exchange Server.