Confused on what I should do to the extent of the VLAN PVID vs

I have a complicated image it's crazy to watch, but I hope I can explain it enough:

I have currently a Powerconnect 2716 connected two Poweredge 2950's particular race as long as ESXi Hypervisors, and their data warehouses are on a MD3000i iSCSI SAN (the main use of the switch is the iSCSI san, servers have connections of backup for the client/guest network access).

Hypervisors vmnic config was hokey at best because we did not have the second gigabit switch to have enough ports to run everything and have redundancy, so I ended up using a lot of 10/100 ports on my Catalyst 3750 PoE switch for guest computers and my iSCSI on the 2716 traffic.

I now have the second 2716 and crosses the configs on the old switch, I realized that I had taken my comments machine network inside out vlan1 and iSCSI ports using the pvid.

Here's my dilemma, I want the network traffic between the two switches for multiple VLANs, but not others.

My proposed solution is

(4) VLANS 1, 10, 130, 139.

(3) GAL: 1 (2-4 ports), 2 (7, 8 ports) 3 (ports 14.14)

belonging to a VLAN will be:

-VLAN1 is for managing the switch, I will have my switches addressed as 192.168.1.1 and 192.168.1.2 and I want trunk VLAN1 LAG1 through so I can handle both switches and either: plug to switch to port 1 with a laptop or use a remote VM guest with shared resources in on LAG2 VLAN

-VLAN10 is for my vMotion, just a 10.x.x.x and me planned to redirect it on the LAG even as my machine comments traffic

-VLAN130 is my iSCSI SAN

-VLAN139 is my Machine/vSphere Client/visitor access

What I fear is VLAN139 traffic with the filtering of capture off the coast and out without label on 16 port which could cross the trunk of LAG 1 (ports 2,3,4) (via VLAN1) and which causes a loop since the 2716 does not support STP.

I want to master the iSCSI, management switch and vMotion across two switches Dell but I want computers invited to climb their respective uplinks of switches. I can't have curls if not all my client/server traffic will cross through a Dell for the other Dell to find the uplink of work when the cisco STP auto disable one of the ports

Can I do this, even if by default, all ports are in VLAN1 unidentified? Or I'll have to this redesign and PVID allows to separate the ports 10-16 and put my VLAN10 on LAG2 as well as iSCSI traffic?

Can VLAN 10 exist on PVID 2 while the trunk between the 2716 is in 1 PVID and always pass traffic between switches?

Have I fried the brain of everyone with my images and my knowledge "just enough to be dangerous?

Thanks in advance! :)

PVID 1 is the default, but if you change it on an interface, page 52 ftp://ftp.dell.com/Manuals/all-products/esuprt_ser_stor_net/esuprt_powerconnect/powerconnect-2708_User%27s%20Guide_en-us.pdf , then it will use the PVID you set to no marked traffic. So if you put LAG3 PVID 139, untagged traffic goes to 139 and tagged will go to VLAN 10. If Cisco is down not signposted in 139 with a PVID of 139, then everything should work correctly with your configuration and do what you want it to do.

Tags: Dell Switches

Similar Questions

  • If I buy adobe Elements 10 or later what software should I make the DVD to mov files, the files are large and I know they must be compressed and I don't want to lose quality... I know that adobe pro you still need software, but will still work with el

    If I buy adobe Elements 10 or later what software should I make the DVD to mov files, the files are large and I know they must be compressed and I don't want to lose quality... I know that adobe pro you still need software, but will still work with the elements and may itself make the compression... I know it can burn DVDs...

    vidog

    If you burn to a DVD disc in first items 10 and later versions, some choices are

    a. DVD-VIDEO standard screen or 4:3 16:9 on DVD disc

    Both will have the frame size of 720 x 480 pixels. But the big screen comes with a 16:9 flag that extends approximately 856/480 16:9 display video after encoding. The screening is not adjustable by the user... and you end up with the DVD-VIDEO format @ 29.97 images per second interlaced.

    b. format of the AVCHD on DVD

    Here is the video display 1920 x 1080. And, depending on the version, can be 29.97 images interlaced per second, or 23.976 progressive frames per second (if not just 29.97 images per second interlaced). Although you can generate some AVCHD DVD with a regular DVD burner, DVD AVCHD is in need of a blu - ray player that supports supported AVCHD DVD or one of these drives multimedia multi which is also.

    c. If the player allows... you can export your Timeline file saved on a USB Flash drive and then insert this USB Flash drive in the drive to get the reading of the file. On this route, you can set the Premiere Elements avancΘs to customize your choice of export preset.

    Please consult the bulletin and consider then, let us know if we have targeted your question. If this isn't the case, please give more details in the areas where we do not have.

    Thank you.

    RTA

  • what patches should upgrade to the BIEE11.1.1.6.0 update to BIEE11.1.1.6.8

    Hello

    I would ask what patches should upgrade to the BIEE11.1.1.6.0 update to BIEE11.1.1.6.8.

    Thanks in advance!

    Hi Leo,

    They are here: https://blogs.oracle.com/proactivesupportEPM/entry/obiee_11g_11_1_1

    I hope this helps.

    Thank you
    Diakité

  • In what format should I save the data definition file

    Hello

    I have to make a minor change in a report to XML editor.

    I downloaded the data model file that says Suppliers.xml

    I made the changes in the query and all recording, it's getting registered as a text document.

    What I have to put .xml in the name of the file while recording.

    In what format should be the data model?

    Kind regards

    Monica

    Any text editor can be used to manipulate xml files. There are also specific xml editors available - comparison of the XML Localization - Wikipedia, the free encyclopedia

  • How do I know what process should run in the background of a HP Pavilion a1020n desktop computer

    There are a lot of processes running in the background of my office, and the amount of memory used varies from 0% to 100%.  Seriously, this affects the performance of my pc, especially if I'm trying to run multiple applications at the same time.  Is there a list of the process 'default' which must be running, and if so, where can I find such a list?

    As I do, that's if you close all the programs that you know how to close there should be only 50-60 process depending on the operating system that you do not specify.

    From there on, organize the task by using the memory manager. Can google those using memory that you want to disable or learn more about.

  • What country should I buy the plan of?

    I am buying a plan for applications (prepaid annual plan).

    I am an Australian, currently staying in Korea and planing to og to the Australia in 3 ~ 4 months.

    I'm not sure which country I would buy the plan of...?!

    Hi Dominic,

    You can buy the plan of the entire region taking into account that the country on the billing address and country of the credit card should be the same thing that the order may be rejected.

    Kind regards

    Sheena

  • What plugin should I copy the MP3 files on a cd.

    I have some MP3 files in my download folder which I would copy
    on a cd, can someone please advise either using WMP or any other method.
    Kind regards.

    I have some MP3 files in my download folder which I would copy
    on a cd, can someone please advise either using WMP or any other method.
    Kind regards.

    ================================
    The following article is maybe worth a visit:

    Windows XP - Windows Media Player 11
    Burn your own custom CDs
    http://Windows.Microsoft.com/en-us/Windows-XP/help/Windows-Media-Player/11/burn

    If you want to try another program...
    DeepBurner is maybe worth a try:

    (FWIW... it's always a good idea to create a system)
    Restore point before installing software or updates)

    DeepBurner Free
    http://www.DeepBurner.com/index.php?r=download
    (Free DeepBurner 1.9 2.67 MB)
    (name of the file to download: DeepBurner1.exe)
    (Windows XP/Vista/7)

    The following link might be worth a visit:

    How to burn CD/DVD with Deep Burner
    http://www.ehow.com/how_4494548_burn-CDDVD-deep-burner.html

  • Can someone tell me what I should type in the screen command prompt to access the setupapi log so I can delete the files that stops me reinstall windows xp?

    My dell PC crashed then I followed the news online & tried to reinstall windows XP from my original CD. However, the keyboard & mouse stop working when the installation gets to the 33 minute section which requires me to a box on the screen. I saw tips online who says lets you check the setupapi log & delete the file question (s) that prevents the installation but it required that use you SHIFT & F10 to enter the command prompt screen, but my keyboard is isolated at this time. So I went in the recovery console (I think it's the command prompt)?  but I don't know which of the listed commands to use to perform the advice. I would be very grateful for help.

    Thank you

    Repair installs being problematic, I would not waste any more time at this stage. You are ready to perform a clean installation?

  • vSphere 4 install ESXi questions what files should I all the other files next to VMware-VMvisor-big-171294 - x86_64.dd?

    I install the vSphere, ESXi on Dell 2900 III Poweredge Server.

    By document, I wonder to decompress the following two files

    install.tgz

    image.tgz

    the extraction of two entrusted gives you the following files.

    # ls - ltr

    Total 922540

    drwxr-xr-x 2 201 201 4096 June 11 15:47 Core

    rrr - 1 201 201 189 June 11 15:47 ThinESX.py

    -rrr - 1 201 201 3618 June 11 15:47 ThinESXInstall.py

    drwxr-xr-x 3 201 201 4096 June 11 15:47 ThinESX

    -rw - rr 1 201 201 943718400 June 11 15:52 VMware-VMvisor-big-171294 - x86_64.dd

    #

    I copy only the VMware-VMvisor-big-171294 - x86_64.dd.bz2_x86_64.dd USB flash.

    DD if = VMware-VMvisor-big-171294 - x86_64.dd of = / dev/sdc

    DO I NEED OTHER FILES?

    Thank you for your help.

    bndwork

    Boot you from the installation CD and let it install on your supported hardware.

    Whatever it is, however, causes the same thing.

    -Matt

    VCP, vExpert, Unix Geek

  • What trigger should write when changing the focus to the record

    Hi all

    In oracle form 6i, I want to trigger an event when changing emphasis of a record to which record in the data block, what trigger should I write the code?

    Thank you and best regards

    Hello

    I think that you can use

    When_new_record_instance trigger to the block level

  • Satellite L650 - what OS should I choose?

    I just bought a spirit L650 h 4 GB of ram, with the installation I'm confused about what OS should I choose 32-bit or 64-bit? What is the difference - all that I want to do is get the new machine operational. Thank you

    Hi roblora,

    I recommend you to choose the 64 bit version of Windows 7, because it supports the full 4 GB of RAM and all 32-bit operating systems support only up to 3 GB of RAM.

    So, if you n t have some older applications, they require 32-bit, choose the 64-bit version and be happy with it! :)

  • Pavilion 20-b313w: confused about what I would do on my PC down performance.

    I am very confused on what I should any performance drop in my PC. My desktop is an all-in-one HP Pavilion 20. The original operating system was WIN 8, current OS WIN 8.1. I have received my computer 08/11/13 and modernized to 8.1 WIN a few weeks later because of the boredom of his pop - ups. The first installation of the failed but the next day he installed on his own and was a success. Not for long after that I started having performance problems. Late development, freezes, screens white or black, poor and choppy graphics audio and app crashes (that have been fixed under the warranty of my HP). A few months after the 8.1 update, I received a message to HP Support Assistant, stating that my computer model is never tested with 8.1 and which could be the cause of performance problems. It also comes with a sweep of compatibility which was of no use since 8.1 was already installed and recommended that drivers become available or uninstall either wait.  I got tired of waiting so December 2014, I made an update to 8 and does a not reinstall the 8.1. I'm back from my excellent performance of computers. Unfortunately that was short-lived due to 8.1 it's self without an option to refuse, automatically reinstalled just a warning that in 2 days it will restart my computer to complete the installation. Happened last week and now my computer is back to low performance once again. The sound is choppy (especially when you're playing), after a few hours use a buzz began, initially it is jerky (on & off), then it becomes constant. Also slow loading and especially the cursor of the mouse that happens on and off delay. I checked Task Manager one day when that was happening and the disk and CPU were turning red and goes up to 100% and the memory of peaks as high, but not up to 100 (between points THAT MEM is still 30% maybe it's due to the recent installation of the Sims 4.  Today, I had a critical event arrives with the core power and my computer restarted, it's self. These are the questions that I need some help fixing, but I have questions that I hope can be answered here or is in the right direction for an answer. (1) how or where I can get a straight answer to my computer with 8.1 compatibility. When I got technical support from HP that I asked about the message, I got on their part and told me to ignore the message because they are compatible. But after I refreshed to WIN 8 the message came back and there was a note at the bottom of the page indicating that the message might be old and possibly there are drivers available. So I'm confused, if the two are compatible then why I experience the same problems that the message was listed as signs of incompatibility? (2) when I use HP Support Assistant to check updates no downloads are available, but when I use the driver and software page for the HP downloads by product website. It shows 10 available for audio download driver, driver chipset, graphics driver, network driver, BIOS, Diagnostics and multimedia software.  I should download them all or do I need to check them one by one to determine if they are old or new. (3) when my computer is idle why are background tasks performing analyses that show on my action Center icon but stop as soon as the cursor is moved? and how do I identify what background process & services can be completed or suspended to improve performance while playing the great resource with games like the Sims 4? Here is some info on my PC and I thank you for taking the time to help me.

    20 - b313w

    8.1 Windows 64-bit

    APU E1 - 2500 AMD with graphics Radeon (TM) HD

    Micron 4 GB 1600 MHz

    AMD Radeon HD 8240

    Resolution 1600 x 900

    refresh rate 60

    Sys. Council 2AFD 1.02

    Sys. BIOS 80.04

    Hard drive C: ST500DM002-1BD142, 445,78 go-go (405,48 free)

    D: 17.71 GB (2.16 GB free)

    Audio Realtek High Definition audio device

    I suggest that you update your drivers of Windows 8 for version 8.1 of Windows drivers.

    I had a quick glance and 8.1 Windows drivers are all new versions.

    Start with the Chipset, video, then the others, but no BIOS [yet].

    Reboot after each installation.

    If the performance seems better after update your drivers to the Windows 8.1 versions then I suggest you also perform the BIOS update is also available.

    Pavilion 20-B313W Windows 8.1 Driver Downloads

    If you found my answer helpful please say thank you by clicking the s cursor Up icon. Thank you!

  • What's not in obtaining the key signature page?

    I have just installed momentics and tried to test the sample application.

    But I failed to get debug and the key signature of token because of web page problem.

    What I should expect that the problem be solved? Or y at - it another way to get these key and the token?

    Present problems with the integration of BlackBerry ID on the site of the developers, that causes this error.  I created a post about it (link below) and will update this thread as things progress.

    Problem with the BlackBerry Developer Site

  • What Messege 'sapp came to the notification bar but wht' sapp does not open and he will be hanged iphone! What should I do?

    What Messege'sapp appears in the notification bar but it does not open and in addition he shall be hanged my iphone6! So, what should I do?

    Try these steps, maybe this will help you:

    1 check WhatsApp update: Open App Store from your iPhone, click on updates, check if the application needs to update.

    2. restart your iPhone: hold down the sleep/wake button to it turn off and then turn it on again.

    3. close the app: multitasking opened by double pressing the Home button, slide the nonresponse apps up to close.

    4. go in the settings, press Whatsapp, touch turn off everything except mobile and notofications data.

    5. return to the home screen and open whatsapp.

    6. go in the settings, press Whatsapp and turn back.

    7. open whatsapp again. It should work now.

  • I use my MacBook Air as a desktop computer. Should I leave the charger plugged all the time or should I drain the battery and then recharge? What is the best for the battery?

    I use my MacBook Air as a desktop computer. Should I leave the charger plugged all the time or should I drain the battery and then recharge? What is the best for the battery?

    Keep the computer plugged in whenever possible.

    If you keep the computer always connected, make sure that at least twice a month

    Run it on battery until battery charge level falls to about 40-50%.

    Please don't completely discharge the battery. Discharge the battery completely will reduce wear and tear on the battery.

    For more information:

    Section: To optimize the battery life

    http://support.Apple.com/en-us/HT204054

    Citing at the bottom of the linked article.

    "The question is often asked:" should I disconnect my laptop from the mains when not in service? Under normal circumstances it should not be necessary because as soon as the lithium-ion battery is full, a properly functioning charger will stop the load and load the pad will only engage when the battery voltage drops to a low level. Most of the users do not remove AC power, and this practice is safe. »

    http://BatteryUniversity.com/learn/article/bu_808c_what_the_user_can_do

Maybe you are looking for