Connection of the PS3 - WRT610N - NAT Fail problems

Similar Questions

• error message ' Add printer. Connect to the printer. Windows cannot connect to the printer. Operation failed with error 0x0000007e"___Any ideas?

  trying to access a lexmark printer installed on xp based computer from a laptop running windows7 via a local network.  Although the network is configured correctly, when I run the Windows printer installation I get an error message ' Add printer.  Connect to the printer.  Windows cannot connect to the printer. Operation failed with error 0x0000007e"I just upgraded to Vista by using the upgrade Acer and had the problems that Windows tried to download the drivers from Lexmark-, but could not. [the same lexmark printer and the configuration worked without any problems before the upgrade on this combination of machines running vista and xp].

  I had a similar problem when I tried to connect to an hp printer that used a Vista driver. Could do this test? Download Windows 7 driver from Lexmark, install it, and then try to connect to the printer again. Andre Da Costa http://adacosta.spaces.live.com http://www.activewin.com

• "Unable to connect to the printer. Operation failed with error 0 x 00000866", setting up a network printer

  Title of the Moose: error 0 x 00000866

  I have a laptop with windows 7 Professional.

  When I try to install a network printer I always get the message "cannot connect to the printer. Operation failed with error 0 x 00000866.

  What can I do to fix this

  Hi ETPM.

  You can try the following steps and check if it helps.

  Method 1:

  You can try to start troubleshooting printer and check.

  Check out the link:

  Open the printer Troubleshooter:

  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Method 2:

  Error message when you try to install a network printer on a Windows Vista-based computer: "Windows cannot connect to the printer operation cannot complete (error 0x0000000d).

  http://support.Microsoft.com/kb/947236

  Note: You can read this article and try to proceed as for Windows 7 also.

  Important: Serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow the steps in the link mentioned above carefully. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, follow the steps from the link below:

  http://Windows.Microsoft.com/en-us/windows7Back-up-the-registry

  Method 3:

  If the fix above is unable to get the printer working on your client machine to vista, so I suggest to follow the steps mentioned by Afzal Taher as of Friday, December 18, 2009 02:00.

  http://social.answers.Microsoft.com/forums/en/w7network/thread/954c4b9d-2F4C-4b1b-8fb6-49204ed96dfc

  Also check out the link:

  Install a printer:

  http://Windows.Microsoft.com/en-us/Windows7/install-a-printer

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Canning Internet connection drops when the computer is connected to the PS3 via an Ethernet cable.

  Original title: Shared network problem

  I am trying to use a shared network, configure as follows. My computer connect wireless to my router. My PS3, however, seems to be really slow when connecting wireless to the router and is at a proper speed when connected via ethernet. So, I have my PS3 connected to my computer with an ethernet cable. I put the wifi connection to be shared. Next, I set up my PS3 to connect to cable internet. Has gone through the steps and connected properly and at full speed too. However, there is a problem. My PC guard 'give up' connection to my router, while remaining connected to the PS3. I have to manually connect to my router again, regardless of the connection automatically option. Almost as if my PC is to use ethernet for internet access, (which he won't get that which is connected to the PS3) and so it loses the wifi connection. This abandonment happens around every 5 minutes or more.

  Is it possible to keep my PC connected to my wireless router and still be connected to my PS3 through ethernet to connect my PS3 using my PC?

  The problem seems to have 'fixed itself. I tried messing around with the connections that would not work even the bridge. Then I've switched back to ICS and did not have a disconnect since then.

  So the problem is now resolved, but don't know how?
  Whatever it is, I am very grateful for your help Manasa, it is well appreciated!

• trying to connect to the PS3 online, my router is microsoft but the SSID is not displayed? Help, please

  Trying to connect to the PS3 online, my router is microsoft but the SSID (or our wireless network name) is not displayed!  Help, please!

  Jamie

  Hello

  1. What is the brand and model of Microsoft Router?

  If you use Microsoft MN - 700 router see link below and follow the steps.

  MN-700 Base Station Configuration Guide

  Download the guide and open page 3 that contains instructions for recording in the router. Page 16 has also the steps to configure the router to broadcast the SSID

  If in case you use a Microsoft MN - 700 router, I suggest you to provide exact model name to get more information about the issue.

  I hope this helps.

• I tried a lot of time to download Lightroom on my MacBookPro without success. I already remove the firewall. Perhaps because of a slow connection to the Lebanon? Or another problem?

  I tried a lot of time to download Lightroom on my MacBookPro without success. I already remove the firewall. Perhaps because of a slow connection to the Lebanon? Or another problem?

  Beatricel88978029 you receive specific when errors download Photoshop Lightroom?  For more information on how to resolve errors download please see error download and installation of the creative cloud application.

• Problems to connect to the ps3

  Hello

  I bought the router e3200 around a month ago and everything worked well until about two weeks ago. Now, when I go on my ps3 I get internet connection and always bad cant hardly play games online more with all the GALs. IM assuming that it is the router because the internet connection is fine when I connect the PS3 directly to the modem. But the internet on my pc seems to work fine with the router, so I'm not quite sure. I tried to connect the ps3 wired / wireless, done all kinds of port forwarding but I'm still not getting the strong connection that I use to have. At first, I just wired my ps3 directly connected to the router with its default value and out of nowhere just got a low internet connection suddenly so I don't know what went wrong. If someone could give me a kind of Council, would be much appreciated.

  Thank you

  If your PC is running well behind the router without delay, it probably isn't the router causing lag.

  If you connect the ps3 with a cable he blames a delay to tell you, but if you are late in the course of the game only I wonder if you have other things running on your PC that can cause lag (downloads, torrents)

  Sometimes it also depends on what game you play online. Some games requires you to connect to one of the other players that have a connection lag.

  Also if you go to the network settings on your PS3 what type of NAT gives you in the view of the State?

  If this is the type of NAT 3, you will have a chance on connection problems while trying to play a game online.

  If it's NAT type 2, it should be good.

  Hope this helps you solve the problem

• Connection with the client VPN for RV110W problem

  Hi guys: I just installed a RV110W router to my small business and I try to connect via VPN from home client.  I was unable to do so, no matter what I try.  Relevant information:

  1. I can connect to the router via remote very well management, so I know that the router is accessible from the Net.

  2. internal address of the router: 10.81.208.1

  3. active PPTP.  PPTP server IP address: 10.0.0.1

  4 IP addresses for PPTP clients: 10.0.0.10 - 14

  5. two VPN clients added - one with PPTP, with the QuickVPN Protocol Protocol.  Both are enabled (and Yes, I triple checked passwords)

  6 encryption MPPE and Netbios active.

  7 IPSec, PPTP and L2TP all active gateways.

  8 VPN client: 1.4.1.2

  9. computer: laptop running Windows 7 family (64-bit), with the firewall Windows is activated.

  10 home network: 192.168.2.196

  It is causing to tear my hair out.  What Miss me?

  Shannon

  Hi Shannon,

  I am pleased to see that you're progress.

  Shannon Rotz wrote:
  I changed the RM port to 443.  Unfortunately, now I can't connect to the router via browser, either by remote management or from the local network - I get the usual "page cannot be displayed".  How do I get back into the router configuration GUI?
  

  You should be able to reach the GUI by typing https://192.168.1.1(assuming that you have not changed the default IP address) normally once you replace http (port 80) with https (port 443) the internal router web server automatically will redirect you to the https page if you type http. Open your command prompt and try to do a ping of the IP address of the router to ensure that it still meets this address

  With regards to the VPN client:   Up until I changed the port, the same error message kept coming up, i.e. "Unable to establish connection" (or something like that), with a list of possible reasons why it couldn't connect. Now the message has changed - I'm getting "Server's certificate doesn't exist on your local computer".  If I continue trying to connect, then it says "Activating Policy", followed by "Verifying Network", then "The remote gateway is not responding.  Do you want to wait?"  This is definitely progress, since I never got this far before.

  You are a quarter inch offline. If you look at the log.txt in C:\Program Cisco Small Business\QuickVPN Client, in my view, you will see "Failed to ping router remote VPN! This means that your PC is blocking the ping to the router response. Usually, if you look at this point the status of Client VPN in the router (first of all need to remote management) you will see that your user status is "connected." If the router thinks that the connection is established, but the PC does not work. You might want to try another PC at this stage to verify that it is indeed a problem with your PC. This problem is usually caused by the 3rd party software antivirus/firewall blocking the ping response. Microsoft Security Essentials can do this as well, so if you turn it off. If you do not have another PC to test from, call Cisco Small Business Support and ask a technician, try to connect to the lab. You can find the number to call here

  On an impulse, I tried setting up a Windows VPN connection, i.e. created a new VPN connection in Network and Sharing Center, using a PPTP client ID that I had created.  That connection actually worked, except for one problem:  I can't see the remote network.  If I could solve that problem, I'll just tell the other clients to use a Windows connection rather than QuickVPN.
  

  Good thought. If you do not see the remote devices, make sure that they do not block VPN connections. (Windows or third-party firewall, antivirus, antispyware) With a connection, PPTP or QuickVPN, you should be able to go to run, type the IP address of the device that you want to connect to (i.e. \\192.168.1.101 ) and see the list of shared folders. After the PPTP connection is established, try to ping the address LAN IP of the router. If it is successful, try to ping a LAN device such as a network printer or a PC. Again, PCs may block ping requests if they have a firewall running watch so for this.

  Answer please if you have any questions.

• C410a - wireless not connect to the Verizon FIOS router - fails MAC filtering

  I just bought an all-in-one HP Photosmart Premium C410a printer.  It does not connect to the Verizon FIOS Actiontek MI424WR router, failed the test of MAC filtering.  Spent half an hour on the phone with Verizon (no resolution as they checked the filtering MAC is turned off in the router) and 3 hours with HP (no resolution).  Sharing the printer on a home network defeated the purpose wireless and is not acceptable because I don't want to have another PC switched on just to get to the printer.  Someone was able to resolve the failure "MAC filtering" wireless?

  Without the MAC address filtering test indicates the problem is inconsistent with other available error messages.

  There may not be a real problem of filtering.  I saw this message associated with WEP key mismatches secutiry and a host of other issues.

  To what extent do you have on the installation.  We can work from there.

  Host family

  P.S. I saw messages asking people to try to disconnect the router from the internet while doing the configuration of the printer.  Have you tried?  Sometimes the router check with the service provider before it will allow a device to join the network.  It bypasses this audit.

• Unable to connect to the server with ttisqlcs, failed to retrieve IP address of the system

  Please help me, I have installed timesten server and client on different machines in the LAN, but with the same user and group - ttadmin:ttgroup

  When I tried to connect to the server with ttisqlcs - connStr "DSN = sampleCS"

  The result gave me errors like below

  Connect "DSN is sampleCS ';.

  S1000: Unable to retrieve the IP address of the system. System error:-2

  The command failed.

  Fact.

  The related part in sys.ttconnect.ini is defined as below

  [192.168.0.206]

  Description = TimesTen Server

  Adresse_reseau = 192.168.0.206

  PORT_TCP = 53397

  And the sys.odbc.ini

  [ODBC data sources]

  sampleCS = TimesTen 11.2.2 Client Driver

  [sampleCS]

  TTC_SERVER = 192.168.0.206

  TTC_SERVER_DSN = nredb_ds

  That wants it mean by 'recovering intellectual '?

  He is trying to resolve IP by hostname even when I already gave him the ip address?

  Either way, I can ping 192.168.0.206 and telnet to port 53397 without problem.

  Please help me, thanks ~

  It does not matter that they are VMs (I use between virtual machines all the time), but "Networking" of VM, of course, must be set up correctly. But if you can ping and telnet between VMS so that shouldn't be a problem.

  On the client computer, you have an entry in/etc/hosts for the client machines and the server? Even on the server? Please check that and add entries if they are not there and see if it helps. If not then we need to find the client using 'strace' to see which system call fails. Please try and after the release (or at least the last part that leads to failure).

  Thank you

  Chris

• Wmp300n connection to the router Netgear WGR614 G problems

  I'm new here so I want just to say hi first.

  I've been lurking here for a while because I bought my 300N. So far, the monitor is undesirable now it is uninstalled and all the drivers are installed. When my DD - WRT flashed WRT54GL is my main router this card is ideal. But I have another problem with two Xbox 360 who do not want to use the same service at the same time, so I bought another router. The Netgear WGR614 v.9.

  I have the 54GL router on a bridge wireless for the 360 so I can have both on the net at the same time. Even when the netgear router is the main router... This 300N wireless card has worked with him for about 10 minutes then just loss of signal. It will not reconnect no matter what I do. I reinstalled it and it still does not connect. The 54GL router is connected to it very well and works.

  There is a problem with the Netgear router what is the map?

  Please if anyone knows that would be great for a response. All forums I go I always ask difficult questions and they never get answered. haha.

  UPDATE: it turns out that it is the fault of WRT54GLs. The DD - WRT software cannot do the job of a customer right wireless I guess. The Netgear router shows that it gives two IP addresses when the router connects with the xbox. It gives the IP router and the xbox and the INVESTIGATION period. But then show that they share the same MAC address. DD - WRT is the MAC of the XBOX and the same as making the MAC like DD - WRT. And no matter how many times I change the MAC it they are both the same to come.

• Presario Notebook PC NV243UA #ABA CQ60419WM does not connect to the internet. Nvidia Driver problem.

  Initially, got a Nvidia 10 code.  Downloaded and installed another NVIDIA driver from a flash drive.  Restore the computer to earier time and currently says Nvidia Driver Helper Service Version 186.44.  Connection to the router is good but the computer does not see the connection.  What can I install to correct driver?  Thank you.  John

  Hello:

  I don't know why the graphics driver is not installed, but you need this driver to connect wirelessly to the internet.

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdDetails/?lang=en&cc=us&sp4ts.Oid=5060882&swItem=ob_108905_1

• Can not connect with the FTP using NAT server.

  Hey, people!

  One machine in the net 200.2.2.0, with ip 200.2.2.222 (ftp client) must connect

  with a server FTP, using the ip 201.1.1.222 nat, but who can not connect.

  A newspaper using, serial interface, I saw the server response to the connection request.

  Using a different disconnection, in fas0/1 of the interface, I don't see the response from the server, I can

  not to see if nat has been done.

  Why?

  What's wrong?

  What can I do?

  To put this machine in another NET, 201.1.1.0 is so hard!

  Look, a router interface has ip 201.1.1.1.

  !

  interface FastEthernet0/0

  IP 201.1.1.1 255.255.255.0

  No cdp enable

  !

  interface FastEthernet0/1

  IP 200.2.2.2 255.255.255.0

  IP nat inside

  No cdp enable

  !

  interface Serial0/0

  Description INTERNET

  IP 100.100.100.30 255.255.255.252

  NAT outside IP

  No cdp enable

  !

  IP nat inside source static 200.2.2.222 201.1.1.222

  no ip address of the http server

  !

  Thanks in advance,

  Renato

  Hello Renato.

  also, it shouldn't make a difference, because your access list allows any last statement, try and add the following line to your access list:

  access list 103 permit tcp a whole Workbench

  access list 103 permit tcp any newspaper host 201.1.1.222 eq ftp

  --> access list 103 permit tcp any what newspaper of host 201.1.1.222 eq ftp - data

  access list 103 permit tcp any newspaper host 200.2.2.222 eq ftp

  --> access list 103 permit tcp any what newspaper of host 200.2.2.222 eq ftp - data

  access list 103 permit tcp any any 0 65365 range journal

  access-list 103 allow udp everything any 0 65365 Beach

  access-list 103 permit icmp any any newspaper

  access-list 103 permit ip any any newspaper

  Also, try to remove the access list together and see if that makes a difference...

  Kind regards

  GP

• After a clean install of Windows 7, I can't connect to the wireless network and more problems...

  I recently did a clean install of genuine copy of Windows 7 Home Premium to clear unwanted programs all on my computer. Because the product key are disabled unexpectedly.

  The installation works fine, but after the installation. I can't connect to a wireless network, because there is no network adapter installed on the computer.

  Also, I can't set my screen resolution of 1366 x 768. Before any new install, the screen resolution sets to 1366 x 768 as native and recommended screen resolution. Now, I'm stuck at the screen resolution 1024 x 768. I need to change the graphics card so my laptop screen can support 1366 x 768? If necessary, please give me instructions on how to do this.

  Thank you.

  Acer Aspire one C5Cbb-722

  Go here, select your model, then download and install the network and video drivers.

  http://www.Acer.ca/AC/en/CA/content/drivers

• BlackBerry Torch 9800 smartphone does not connect to the server and server BBM problem

  I have a BB Torch 9800 and starting the 29th Dec e-mail could not be received and BBM works do not. I have nothing, they just stopped working.  Made all types of hard reboots even take off the battery and SIM card, and works in the BBM id. Just downloaded BBM app ver 7.0 thinking he would help and now get BBM, temporary server problem message.

  Help, please. Provider is AT & T.

  Thank you and happy new year who can get my BB working again!

  bbarnes821

  My guess is that your supplier, ATT, changed your data plan. Call them and make sure that your account is configured correctly for BB services.