Connectivity with XP issues

Similar Questions

• PowerBeats 2 (wireless) connection with iPhone issues 6

  I currently have iOS 10.0.1 and a pair of wireless 2 PowerBeats headphones that I use at the gym. I tried to use the updater of beats without success to fix my connection problems. Whenever my iPhone 6 is face down, in my pocket, behind an obstacle, or generally out of line of sight of my 2 PowerBeats connection starts to act up by disconnection or broken.

  The is because the signal is blocked by what is between your iPhone and PB2.

• In a roaming network, Mac always connects with AE which is further away

  So, I had a roaming network for years to host a detached office which was too far from my house.  Worked very well.  Now, my family and I have moved into a temporary rented condo (two floors).  Therefore, there is a lot of wifi networks in the area in conflict with.

  After trying to extend the network (signal too low in the area), I decided to try the roaming network again.  Most of the time, it works very well.  But from time to time, my iMac (on the ground floor) connects with the Airport Extreme, which is on the floor instead of the Airport Express, which is down in the same room as the iMac.  What happens when it connects to the Airport Extreme on the floor, my Tx rate drops to less than 100 Mbps (sometimes dramatically if) and I am unable to listen to the music to my Airport Express without dropouts.

  The dressing was to turn off my wifi on the iMac, and then turn it back on.  It will then connect to the Airport Express.   The problem is that I have to do this in general once a day as my iMac will enter into the "standby" and periodically reconnect with Airport Extreme when I wake up (or if I re-enable it if off).  Ideally, he would stay with the Airport Express.

  So I hope that there is an alternative.  I thought about simply renaming the Airport Express network in the different name of Airport Extreme.  But all the itinerant instructions whereby I know that network names must be the same for all airports in the roaming network.  But perhaps this is not the case.

  Comments are appreciated!

  Unfortunately, you encounter a known issue with the use of a roaming network... and it is not specific to those provided by Apple either. The "solution" you use, although not elegant, is basically everything with that we have (at this time) to go.

  In theory, your iMac fixed, must always connect to the Wi - Fi with the signal network hard... not necessarily the closest to it. It may be possible, since you mentioned that you live in a highly congested environment Wi - Fi, your iMac is struggling to determine the right network to connect to when starting.

  Of course, a more "permanent" solution for your iMac, at least, would connect directly to the nearest base by Ethernet station.

• Thunderbird does not connect with the server

  Another recent problem is Thunderbird does not connect with the server. I don't know if sent mail will go out, but I know I'm nothing receive. My internet connection works well for FF or another browser. I checked my settings and they seem OK. I checked the default settings in Win10x64 and they are correct. Any ideas?

  Although windows 10 is new for us all. How do solve you. I have other solution with very similar issues.

• Bluetooth speaker no connection with iPod 5th generation

  Once solve you one problem, another pops up...

  A little more than a week ago, I bought an iHome iBT3, which is a protected against splashing, triangular-shaped speaker. It has bluetooth, which I used about three times now and it was working fine until today.

  The other day I had a problem with my iPod which translates into me trying the three methods; force reset, recovery of the device and reset all default settings. Although I have fixed my previous issue, when I tried to connect my speakers today, connected devices emerged as two things that I had never seen before. I chose the setting for iPod to 'forget' the devices and tried to connect my speakers.

  I watched for 15 minutes. The speaker tried to connect and connect and connect the iPod has tried to find the device, and they never linked between them; my iHome does not appear on my iPod and my iPod never read that there is a device in the region.

  I tried to force the delivery twice, the iPod and it has nothing and if it should happen again, I really, really don't like to restore my iPod because it took me two days and multiple handfuls of hair to do such a thing.

  Can I do to get my two devices to connect with each other?

  Thank you in advance.

  Update: The speaker is not connecting to my or my sister iPods.

  My father has a similar Bluetooth speaker if and which connects both of the devices.

• cannot connect with facebook

  I I open avast account and click on connect with facebook and not out to connect and other sites also.

  Hello

  Try Firefox Safe mode to see if the problem goes away. Safe mode is a troubleshooting mode, which disables most of the modules.

  (If you use it, switch to the default theme).

  • Under Windows, you can open Firefox 4.0 + in Safe Mode holding the key SHIFT key when you open the desktop Firefox or shortcut in the start menu.
  • On Mac, you can open Firefox 4.0 + in Safe Mode holding the key option key when starting Firefox.
  • Under Linux, you can open Firefox 4.0 + with leaving Firefox then go to your Terminal and running Safe Mode: firefox-safe-mode (you may need to specify the installation path of Firefox for example/usr/lib/firefox)
  • Or open the Help menu and click on the restart with the disabled... modules menu item while Firefox is running.

  

  Once you get the pop-up, simply select "" boot mode safe. "

  

  If the issue is not present in Firefox Safe Mode, your problem is probably caused by an extension, and you need to understand that one. To do this, please follow article Troubleshooting extensions, themes and problems of hardware acceleration to resolve common Firefox problems .

  To exit safe mode of Firefox, simply close Firefox and wait a few seconds before you open Firefox for normal use again.

  When find you what is causing your problems, please let us know. It might help others who have the same problem.

  Thank you.

• Information sharing: for some reason any Mozilla is unable to connect with Chase Bank. Users of Mozilla need help!

  I wanted to just make sure that Mozilla went in there was a problem using Firefox to connect with Chase Bank. I was able to complete my activities, but I had to use MS IE to do. Is this something be done to correct this situation?

  Many issues of the site can be caused by corrupted cookies or cache. To try to solve these problems, the first step is to clear cookies and cache.
  Note: This will be you temporarily disconnect all sites, you're connected to.
  To clear the cache and cookies to do the following:

  1. Go to Firefox > history > clear recent history or (if no Firefox button is displayed) go to tools > clear recent history.
  2. Under "Time range to clear", select "all".
  3. Now, click the arrow next to details to toggle the active details list.
  4. In the list of details, see the Cache and Cookies and uncheck everything.
  5. Now click the clear now button.

  More information can be found in article to clear your cache, history, and other personal information in Firefox .

  This solve your problems? Please report to us!

• My iPhone 6 guard making his power on and off loading when it is connected with the MacBook Air early 2015

  Hi Please help me. My iPhone 6 retains what load noise when connected with my MacBook Air early 2015. It makes me crazy! I tried with several real Apple's USB cables, update to the latest iOS (phone and MacBook), updated the iTunes, clean the orifices, everything! I just got this MacBook on the Apple store. Please help me! Thanks in advance!

  Hi mikaelaridz,

  I understand that you just bought a MacBook Air in an Apple store, and when you plug your iPhone 6 in it, you are to hear a sound indicating that the connection does not work.  If your MacBook Air has a port USB - C, you must use the USB - C for Lightning cable to connect your iPhone.

  Using the USB - C port and adapters on your MacBook (retina, 12 inch, early 2015) and later

  Port USB - C

  USB - C is an industry standard generation that allows to load and transfer of video data - while a simple connector. Your MacBook comes with a USB - C port:

  

  Through this port, you can:

  • Charge your MacBook.
  • Power output.
  • Transfer data between your MacBook and other devices.
  • Connect the video output such as HDMI, VGA and DisplayPort.
  • Connect to other technologies, such as Ethernet.

  Port USB - C on your MacBook supports data transfer speeds to up to 5 Gbps (USB 3.1 Gen 1).

  USB - C for Lightning cable

  Apple USB-C for Lightning cable allows you to connect any device equipped with a connector of lightning with your MacBook. It provides data transfer and power of lighting fixtures. For example, you can use this cable to connect your MacBook to these devices:

  • iPhone, iPad and iPod touch
  • Magic Mouse 2
  • Magic keyboard
  • The Magic Trackpad 2

  You can also load these devices without using your MacBook by connecting to the C - USB to the lightning cable and plug the cable of the USB - C 29W power adapter.

  USB - C for Lightning cable supports data transfer at up to 5 Gbps (USB 3.1 Gen 1).

  This cable requires no power to operate. However, devices that you plug into it could draw power from your MacBook, you should unplug it when you're not using it.

  If this isn't the issue, then I suggest taking your new MacBook Air and iPhone at the Apple Storewhere you bought it.  A genius can inspect your computer for you, there is no hardware problems and staff can help you set up.  Here's how Contact Apple and make an appointment.

  Take care

• Connectivity with AT & T-Motorola 3360 and Airport Extreme problems

  Bought a new extreme-Airport (7.7.3) to replace my old AE after 9 years of service.  The installation procedure, but could not get the airport to connect with my modem (Motorola 3360).  Called at & T and they crossed put me the modem in Bridge mode and which seemed to work.  But only temporarily (about 5 hours).  Restart the modem and the airport was not working.  Troubleshooting I tried to plug my MacBook directly into the modem, but even the computer couldn't get an internet connection.  Another call to AT & T and they reconfigure the modem to their end.  After 90 minutes and try everything they could, they have finally admitted defeat and told me that they could not solve the problem.

  However, after a fairly exhaustive search of this forum, seems to be two issues that many people is with Airport extreme.  One is that the modem (in this case a Motorola 3360) is perhaps not fully compatible with the airport.  The AT & T support person was not aware of this until I asked about it, so she did a quick search and was rather surprised to see that there is a lot of people having problems with the Motorola Modem.  She told me that they use no more Motorola modems but ship the 6200 of Netgear.  "All know issues?", I asked.  She sought and, to his surprise, even once, there was.

  So, first question.  Does anyone know a modem that is compatible with the airport or use one that they had to limit problems with?

  The second question prevailing seems to be with the IPv6 protocol.  Anyone know if there are problems with the AT & T IPv6 protocol and the most extreme airport?  I did not disable IPv6 yet to see if that helps.  I thought I'd ask here first.  Couldn't find anything on the AT & T site.

  When I return from the road (great place to go to get away from technology) I will make a new round of full power of all the components and try Setup again from scratch.

  Any ideas or suggestions would be greatly appreciated.  Miss all know profanity.

  Thank you.

  Any other relevant information: 6.3.1 the utility Airport, Airport Extreme 7.7.3, MacBook Pro running 10.8.4, modem Motorola 3360, AT & T high speed DSL, shoe size 11-1/2 wide.

  When you have configured the 3360 as a 'bridge', this would mean that the AirPort Extreme should then be put in place to provide the PPPoE connection service. The airports are not known for their reliability in this type of installation... no matter the type of modem that you can select, so I drop this method as a connection option.

  If you want to keep the 3360... and you have time to experiment... then you can set the 3360 to its original default settings and configure the router from the airport most convenient to connect using DHCP in router Mode of DHCP and NAT.  That will produce what is called a message Double NAT, but maybe it's not of concern on a simple home network, and Apple provides you with the option 'Ignore' the Double NAT, so the airport will display a green light instead a light orange blinking slow.

  You need to try this configuration for a few days to see if the Double NAT will be a problem or not, because it is not possible to predict the effect of a Double NAT on a network... you have to test a few days see how things behave.  If this configuration works well, for you, then you can leave it as what.

  Please note that I do not recommend this type of installation, just suggesting it as an option this work could , if you want to keep the 3360.

  How Double NAT affect IPv6, I can't tell, since I did not use att for several years, and I'm not familiar with their implementation. On wired, IPv6 works fine on the airport with Comcast and Time Warner.  We can provide these parameters for you if want, but have no idea how well... (or if)... they will work with ATT.

  If the installation of Double NAT does not work, your best option would be to go there and get a modem/router or gateway to ATT device and then set up the most convenient airport in Bridge Mode works correctly with the modem/router ATT.  You will turn on the routing of ATT function in this type of installation, but the airport can also produce a signal from the wireless network that you can use.  The modem/router ATT will also provide a wireless signal that you could use for guests, or disable the feature, if you do not need two wireless networks.

  This may also be the best option if you want to configure IPv6 as IPv6 of ATT service must be compatible with the modems/routers and gateways.

• Internet connectivity with iOS 9.3 problems

  I have an iPhone handset 6

  Since the update the handset does not connect to the internet.

  Indeed, despite a complete network redefined and, when the connection through wifi to my router at home and tries to access the internet - no luck!

  IPhone 6 combined - still on the old version - disorder web access my wife.

  I can only put it down to the upgrade and the information circulating on the net about similar issues.

  The iTunes doesn't seem to recognize that there is a more recent patch for the 9.3 iOS version 13E233. Some sites there indicate iTunes should detect a fix updated since this original version. I saw the reference to 13E234.

  Help, please. Frustrating that *!

  iOS updates regularly change of variables operating system which, from time to time, will affect negatively other parameters and the features of the component on the device (including WiFi).  In addition, this can be a problem with your carrier and the specifics of your plan data or of the SIM card in your device settings that need to be addressed or refreshed.  To update the carrier settings, place a call to your carrier and place them on your device.

  This particular issue on the side of the Apple of street connectivity has been surfacing regarding the update and its been mainly a question of the environment such as WiFi access or your router (s) your help, I've had this as well and here are the most effective steps, I can give you to solve.

  WiFi/Internet environment

  1 restart your router

  2. check the latest version of the firmware on the router (router manufacturer and manual will have instructions on this one)

  Apple IDevice

  3. remove the WiFi access point of your iDevice which is the blue tick, if its power to establish at least a connection with your internet facing router it is a very practical and viable step to achieve. Settings > WiFi > * WiFi Access Point name * > forget this network (another option is to simply renew the lease, which will be used in blue at the bottom of this screen) my recommendation is to forget this network and let your iDevice and the router to build a new pile of access point.

  4. (optional if nothing above has solved the problem on this point) reset network setting on your iDevice, you will probably need to provide credentials for your router here.  Settings > general > reset > reset network settings > restart

  5. last resort to restore your device using iTunes, using iTunes on your Mac or PC to restore the iPhone, iPad or iPod to factory - Apple Support

  It is a fairly complete set of instructions to identify it's a software or a configuration issue with your device.  If after that you had accomplished each of these steps, the problem is not resolved, move to consider a repair like the WiFi hardware physically in the device may be damaged.

  See you soon

• Tecra 8000: No memory available to connect with area map PC

  I have a Tecra 8000 running Win98 SE and use a card PCMCIA 3Com for my Internet connection. I was troubleshooting my computer on another issue and in the process disabled Cardbus PCMCIA Toshiba ToPIC controllers. After you have enabled these again once I am more able to communicate with the PC card and so unable to connect to the Internet.

  Card troubleshooting agent PC States: "Windows is not able to identify or use the inserted PC card device because there is no available memory area to connect with this device. You need to do an area memory available before this device can be used. Check the CONFIGURATION of your computer. A memory manager that is excluding the regions of superior memory between A000 and FFFF in the SYS file '.

  My Cardbus controllers are defined as follows:
  1 memory range - 0c 000000 - 0C000FFF
  2 memory range - 001000 0c - 0C001FFF

  My PC Card (PCMCIA) properties are as follows:
  Card services shared memory:
  Start 000c 0000
  End 00FFFFFF
  Length 00001000

  While the PC Card Modem is recognized at the Port, it can be communicated with and error message is shown as follows:

  ' Error 666: the modem is not plugged in or is out of service. "Connect a modem to your computer and try again.

  When I run the Diagnostics on the Modem does not respond to the exception of the following:

  "' Open Comm: cannot open port"

  Any help or advice will be appreciated.

  Have you tried to uninstall the Cardbus drivers? Not sure about the location in Win98 (in XP it is in Device Manager), go to "PCMCIA adapters" and uninstall all entries in controller.

  Reboot and Win98 will perform his routine "new hardware found". This is going to re - install drivers and with a bit of luck should solve your problem.

• Re: Portege Z30: Fingerprint software does not, the connection with the sensor fails

  Hello to you all,.

  I have a great fun for you guys. If you're curious, it's here...

  I just bougt garage a portege Toshiba Portege Z30t-A-126 PT24CE-01400HFR
  Nice machine but SSD is too small, so I changed the original SSD 256 to a 512.

  Reinstalled Win7 completely without any pb.

  Just a pb in fact: the footprint software does not work.
  When I hliant, it fails and says "unable to connect with the sensor.

  In french "fingerprint recognition."
  Unable connect the sensor.

  But when I check the Device Manager computor it says that everything is in place and ongoing execution, validity (WBF) (PID = 0010) sensors works very well and the latest version of the driver is installed.
  (I downloaded the form driver toshiba Web site.) The name of the driver is fp - sw - 20140115084521.zip)

  Then? What's not?

  I spent hours searching the web and tried everything I could. Reinstalled a thousand times the drivers, software, tried other drivers... But there is no way that I can fix it.
  It's really annoying...

  Can someone help me please? Have you an idea? I'm stuck...

  Thanks in advance. :-)

  Hello

  This issue of the fingerprint has been described in another thread.
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=81261

  You should be able to solve the problem installing the chipset driver.
  Another user said, an installation of Proset Ethernet drivers/software was necessary to get the problem resolved. But to be honest that I put t think that missing Proset utility would cause the question

  However, check it out.

  Your comments would be appreciated

• Just installed the new Win10 great Update.When iTunes will connect with Gracenote?

  Just installed the new major update of Win10. When will be able to connect with Gracenote when you import music from a CD to iTunes?

  It doesn't seem to be a link between issues with Gracenote and updates of Windows 10.  The last - which is usually accompanied by a cryptic error "no error" message, or one that says 'User unregistered for use online' - usually come from corruption to one of iTunes preference files.  Try the following:

  1. Quit iTunes
  2. In the Windows search box, enter %APPDATA%\microsoft\windows\sendto in the address bar, press .  This will open the C:\Users\username\AppData\Roamingfolder.  Then open the Apple Computer and in this framework the iTunes file.
  3. Delete the following files:
     • CD Info.cidb
     • com.apple.iTunes.Gracenote.plist
  4. Restart iTunes
  5. Insert a CD and see if details are now correctly retrieved from Gracenote

  If this does not work:

  1. In iTunes, select Edit > preferences and a note (or take a screenshot) of your settings preferences in all tabs
  2. Quit iTunes
  3. Repeat step 2 in the previous procedure to open the C:\Users\of\AppData\Roaming\Apple Computer\iTunes user namefolder.
  4. Delete the following file:
     • iTunesPrefs.xml
  5. Restart iTunes
  6. Restore your settings to preferences iTunes to those that you noted in step 1.
  7. Insert a CD and see if details are now correctly retrieved from Gracenote

  If no si aucun succes success so far, try to repeat the two procedures above, using records C:\Users\username\AppData\Local\Apple Computer\iTunes and C:\Users\username\AppData\LocalLow\Apple Computer\iTunes.

  If it wasn't (and most people reported that the problem is solved by one of the two procedures above):

  1. Quit iTunes
  2. In Windows, select Start > Control Panel > Add / Remove Programs.  Look for the entry of iTunes, right click and select Rrepar.
  3. When this process is complete, restart iTunes
  4. Insert a CD and see if details are now correctly retrieved from Gracenote

  If the problem persists, you may uninstall and reinstall iTunes - see tips to the user of turingtest2 on troubleshooting issues with iTunes for Windows Update for more details of the steps necessary to remove completely all the components of iTunes before reinstalling.

• Unable to connect with the PC tab

  I bought a Ubislate android 7 C + from Datawind, but unable to connect with the computer

  Burnersalvation,

  To provide the proper resolution, I would need more information on your side.

  1. which version of the operating system are you using?

  2. what happens when you try to connect to the tab?

  3. How do you connect tab to the computer?

  To connect to Android Ubislate to the computer, it may require some software to install on the computer provided by the manufacturer of the tab. Then I suggest you to contact the manufacturer of the tab to get help on this issue.

  Check out the link:

  http://www.ubislate.com/contact/index.html

  Hope this information helps. If you need more assistance or information on this question, reply to this post. I'll be happy to help you.

• Error message when connecting with wireless USB modem

  Dear Sir/Madam,

  I use the HP laptop with Windows vista operating system. I'm also using the USB wireless modem. But now, I had problem connecting with usb modem. I get ((erreur (6): could not get the string) message connecting with.) Kindly help me to solve the problem.

  Thank you
  Kind regards
  D.Yokesh

  Hi D.Yokesh,

  1. did you of recent changes on the system?

  If it is a recent issue, then you can try a system restore to a prior restore point you have been affected by the issue.

  Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

  To run the system restore, you can consult the following link:

  System restore

  System Restore: frequently asked questions

  Hope this information is useful.