Console remote vCenter access (NAT problem)?

Hello world

I have problems accessing my VMRC via vCenter WebClient.

My network config is as described in the title:

my office LAN (say 192.168.1.50)-> firewall-> my server room (say 10.1.1.0/24).

the ESX and vCenter are in the server room.

To access the server room,'s done it through NAT (IE to access my true IP vCenter 10.1.1.10 I access from my desktop to 200.1.1.10).

When I access the remote console hollow vSphere Client (so connecting directly to ESX without using vCenter) works (the console log shows that I connect to the NAT address).

When I want to access a remote console trough the web interface, the console to it log shows tries to reach the REAL of ESX instead of the NAT one address.

I hope that I was enough to get a clear answer

Is - this repairable or y at - it a parameter that escapes me in vCenter to make this setup work (I did research all morning without finding a clue).

Thanks in advance and forgive my approximate English.

I finally find myself...

I assumed that, as a result of posting here makes me think differently!

Solution: Add the host whose DNS name in vCenter instead of IP addresses, then the VM consoles work properly.

Tags: VMware

Similar Questions

Console remote vCenter - the server name cannot be resolved

When I run the utility of Vcenter web-based console, a new web page opens and displays the console but I get the following error:
"The server name could not be resolved."
Here is a screenshot:
Here is the URL of the remote console tries to display:
:9943/vSphere-client/VMRC/VMRC.jsp?VM=urn:vmomi:VirtualMachine:VM-105:A5FB093-945A-4288-8DC1-4C64B0E4D4D9 https://172.16.1.1
I am a student from progressing to a VTC VCP5 Certification community college. We use the VMware Network Netlab Academy facility. I have no access to the client based on Windows Vcenter. I have only the client on the Vcenter web access.

Many many thanks Andre! The work of Console launch. After that I removed the entries in/etc/hosts localhost to the server vcenter-1, I brought successfully to the top of the console window. Of course, I also had to add an entry for the host esxi-1 in each file/etc/hosts.

The console works great. I was able to connect and send commands of Linux; However...

The only remaining question I have is that the console returns to Mode "full screen" by default and I can't seem to exit full screen mode. It encloses the vclient overall utility. Is it possible to tell the coming launch mode console non-plein default screen? Y at - it a remote console setting that controls "Full Screen Mode".

Scott...

Cannot access the Console remotely

Hey guys, I'm new to VM Ware and has difficulties to access the console remotely, even if I can access the Web Access page very well...
The error I get is:
Unable to connect to the MKS: unable to connect to the host domain.com: no connection could be made because the target machine actively refused
When you search for an answer to this, I found a post that said to ensure that the /etc/pam.d/vmware-authd has been configured correctly, as well as the/etc/vmware/config...
None of these files/folders are there.
That said, my host OS is (unfortunately) of Windows Vista, with VM Ware running on top of that, and now I am trying to get Fedora Core 11 to present itself as the virtual machine.
Any ideas you can give would be much appreciated.

Sorry, I did not myself clear - its port 902 on the host that you need to check that you can telnet to because the VMware console connections are made using the host (so that they can still operate even when there is no network in the comments, for example at installation time), not to the guest directly (for client firewalls are not the parameters used either for the console). I guess that 8333 is fine, otherwise you wouldn't be able to connect remotely to the web console.

Guy Leech

VMware vExpert 2009

---

If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

WHS 2011 Media - Web remote access - a problem with the media of files appearing not

I'm running WHS 2011. When I connect via a remote web access and media sharing is turned on, I can see the three categories in the window 'Library' - 'Browse images', 'Browse music' and "browse videos". I have several songs in the "ServerFolders\Music" folder on the server and I used to see the album art in the home screen remote Web access under 'Browse music. " Now, the icon 'Browse music' on the screen of remote access Web says "0 songs" even if I have not moved or removed all the songs in the folder ServerFolders\Music on the WHS machine. If I go to the "Shared folders" window and open the 'Music' it on access web remote, all the music files are listed as expected.

I don't know how to reset or refresh the window "Multimedia library" in order to recognize the music files I have on the server.

Please advise...

Thank you for your help.

Hello

You can publish your application in the Windows Home server to improve the assistance:

http://social.Microsoft.com/forums/is/whs2011/threads

ASA 5505 VPN remote cannot access with my local network

Hello guys, I have a problem with my asa 5505 remote VPN access to the local network, the VPn connection works well and connected, but the problem is that I can't reach my inside connection network of 192.168.30.x, here's my setup, please can you help me

ASA Version 8.2 (1)

!

!

interface Vlan1

nameif inside

security-level 100

192.168.30.1 IP address 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP 155.155.155.10 255.255.255.0

!

interface Vlan5

No nameif

no level of security

no ip address

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

passive FTP mode

inside_nat0_outbound list of allowed ip extended access any 192.168.100.0 255.255.255.240

pager lines 24

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

IP local pool vpn-pool 192.168.100.1 - 192.168.100.10 mask 255.255.255.0

ICMP unreachable rate-limit 1 burst-size 1

don't allow no asdm history

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access inside_nat0_outbound

NAT (inside) 1 0.0.0.0 0.0.0.0

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

dynamic-access-policy-registration DfltAccessPolicy

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Telnet timeout 5

SSH timeout 5

Console timeout 0

dhcpd outside auto_config

!

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

Mull strategy of Group internal

attributes of the Group mull strategy

Protocol-tunnel-VPN IPSec

username privilege 0 encrypted password eKJj9owsQwAIk6Cw xxx

VPN-group-policy Mull

type mull tunnel-group remote access

tunnel-group mull General attributes

address vpn-pool pool

Group Policy - by default-mull

Mull group tunnel ipsec-attributes

pre-shared-key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

!

global service-policy global_policy

context of prompt hostname

Yes, you will need to either configure split tunnel so that internet traffic goes out through your local Internet service provider, GOLD / directed by configuration current you are tunneling all traffic (internet traffic Inc.) to the ASA, then you will need to create NAT for internet traffic.

To set up a tunnel from split:

split-acl access-list allowed 192.168.30.0 255.255.255.0

attributes of the Group mull strategy

Split-tunnel-policy tunnelspecified

Split-tunnel-network-list value split-acl

I hope this helps.

Customer remote cannot access the server LAN via VPN

Hi friends,

I'm a new palyer in ASA.

My business is small. We need to the LAN via VPN remote client access server.

I have an ASA5510 with version 7.0. I have configured remote access VPN and it can establish the tunnel with success. But I can not access the server.

Client VPN is 5.0.07.0290 version. Encrypted packages have increased but the decrypted packet is 0 in the VPN client statistics, after I connected successfully.

Next to the ASA, I show crypto ipsec sa, just deciphering the packets increase.

Who can help me?

Thank you very much.

The following configuration:

ASA Version 7.0(7)
!
hostname VPNhost
names
dns-guard
!
interface Ethernet0/0
nameif outside
security-level 10
ip address 221.122.96.51 255.255.255.240
!
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.42.199 255.255.255.0
!
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
shutdown
no nameif
no security-level
no ip address
management-only
!
ftp mode passive
dns domain-lookup inside
access-list PAT_acl extended permit ip 192.168.42.0 255.255.255.0 any
access-list allow_PING extended permit icmp any any inactive
access-list Internet extended permit ip host 221.122.96.51 any inactive
access-list VPN extended permit ip 192.168.42.0 255.255.255.0 192.168.43.0 255.255.255.0
access-list VPN extended permit ip 192.168.43.0 255.255.255.0 192.168.42.0 255.255.255.0
access-list CAPTURE extended permit ip host 192.168.43.10 host 192.168.42.251
access-list CAPTURE extended permit ip host 192.168.42.251 host 192.168.43.10
pager lines 24
mtu outside 1500
mtu inside 1500
ip local pool testpool 192.168.43.10-192.168.43.20

arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list VPN
nat (inside) 1 access-list PAT_acl
route outside 0.0.0.0 0.0.0.0 221.122.96.49 10

username testuser password 123
aaa authentication ssh console LOCAL
aaa local authentication attempts max-fail 3

no sysopt connection permit-ipsec
crypto ipsec transform-set FirstSet esp-des esp-md5-hmac
crypto dynamic-map dyn1 1 set transform-set FirstSet
crypto dynamic-map dyn1 1 set reverse-route
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface outside
isakmp enable outside
isakmp policy 1 authentication pre-share
isakmp policy 1 encryption des
isakmp policy 1 hash md5
isakmp policy 1 group 2
isakmp policy 1 lifetime 86400
isakmp nat-traversal 3600
tunnel-group testgroup type ipsec-ra
tunnel-group testgroup general-attributes
address-pool testpool
tunnel-group testgroup ipsec-attributes
pre-shared-key *
telnet timeout 5

ssh timeout 10
console timeout 0

: end

Topology as follows:

Hello

Configure the split for the VPN tunneling.

Create the access list that defines the network behind the ASA.

ciscoasa(config)#access-list Split_Tunnel_List remark The corporate network behind the ASA. ciscoasa(config)#access-list Split_Tunnel_List standard permit 10.0.1.0 255.255.255.0

Mode of configuration of group policy for the policy you want to change.

ciscoasa(config)#group-policy hillvalleyvpn attributes ciscoasa(config-group-policy)#

Specify the policy to split tunnel. In this case, the policy is tunnelspecified.
```
ciscoasa(config-group-policy)#split-tunnel-policy tunnelspecified 
```

Specify the access tunnel split list. In this case, the list is Split_Tunnel_List.

ciscoasa(config-group-policy)#split-tunnel-network-list value Split_Tunnel_List

Type this command:

ciscoasa(config)#tunnel-group hillvalleyvpn general-attributes

Associate the group with the tunnel group policy

ciscoasa(config-tunnel-ipsec)# default-group-policy hillvalleyvpn

Leave the two configuration modes.

ciscoasa(config-group-policy)#exit ciscoasa(config)#exit ciscoasa#

Save configuration to non-volatile RAM (NVRAM) and press enter when you are prompted to specify the name of the source file.

Kind regards
Abhishek Purohit
CCIE-S-35269

Unable to connect to the MKS: the certificate of the remote host has these problems:

Hello
We have a host of ESXi 4 cluster running any vSphere 4.1. Recently, I started to upgrade to update 2 and all the additional fixes. After the upgrade of the vCentre server to the latest version (or maybe before I can't noticed) an of are hosts began to show the following error whenever I tried to connect to the console of any guest on this host.
Unable to connect to the MKS: the certificate of the remote host has these problems:
It lists any problems at all and no error display in the event log that it simply does not work. I had a prod around the internet and found nothing. I then rebuilt the host to exclude and the problem remains.
Any help would be much appreciated.
Thanks in advance
David

If you can connect to the Console remotely using VMware Infrastructure (VI) Client connected directly to the host, take a look at vmware KB to connect to a remote virtual machine fails with the error: the certificate of the remote host has these problems

but more generally - remove host to vCenter inventory and then add the host to the back, take a look at opening in the console of the virtual machine after a new installation of ESXi or ESX fails with the error: the host certificate chain is not complete and could not connect to the MKS: the certificate of the remote host has these problems

Remote ftp access

I can't get a remote ftp access to my NMH405. I access remotely through https://ciscomediahub.com/ and can browse my files this way, but I need to have a remote access via ftp as well. I put a ut ftp access and it works locally on my home network.

What is my ftp address?

Can anyone help me please with this problem?

Hi Erikkoken,

You will also need to know the external IP address of your location. You can find it at http://www.whatismyip.com/. My internet service provider gives me a dynamic IP address, so it will change every 24 hours. To resolve this problem, I have install dynamic host for me to http://www.dyndns.com/name. You will also need to read the instruction manual for router for DDNS, so you can tell it where to point to and update the IP address.

I hope this helps.

Vuze download is very slow... He pointed out that I have a nat problem

nat problem?

Vuze download is very slow... He pointed out that I have a nat problem... Help please.?

Hello

·        What browser do you use to access the internet?

·        What is the full error message that you receive?

·        Is it only when you download on Vuze?

I suggest that temporarily disable you antivirus software and firewall installed on your computer and check to see if it helps:

Disable the anti-virus software

http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

Enable or disable Windows Firewall
http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

Note: disabling anti-virus or Windows Firewall can make your computer (and your network, if you have one) more vulnerable to damage caused by worms or hackers.

You can also post your query on Vuze forum to get help:

http://Forum.Vuze.com/index.jspa

remote users access site ipsec tunnel

How to configure the ACL and the road to allow remote users access to site ipsec as local users?

Current scenario is

1. distance users (192.168.2.0/24) ipsec <->Cisco 870 (192.168.0.0/24)

(2 cisco 870(192.168.0.0/24) ipsec tunnel <->cisco 1811 (10.0.0.0/24)

Now remote users can access the 192.168.0.0 network, no problem, but how they can access 10.0.0.0 network?

I guess I can do like this:

1. in cisco 870, site to site ip 192.168.0.0 tunnel allow 0.0.0.255 10.0.0.0 0.0.0.255

(add) permit ip 192.168.2.0 0.0.0.255 10.0.0.0 0.0.0.255

2. in the site-to-site vpn cisco 1811

(add) permit ip 10.0.0.0 0.0.0.255 192.168.2.0 0.0.0.255

3. in settings vpn split cisco870 add the 10.0.0.0/24 network

Is this fair?

Thank you.

You must configure the interesting traffic that an ACL contains the source is remote destination as local LAN and LAN.

Remote VPN access - add new internal IP address

Hello

I have an existing configuration of Cisco VPN client in ASA 5510 for remote access.

-------------------------------------

Name of the Group: ISETANLOT10

Group password: xxxx

IP pool: lot10ippool, 172.27.17.240 - 172.27.17.245

enycrption: 3DES

authentication: SHA

------------------------------------

the connection was successful, and I was able to ping to the internal server 172.47.1.10.

Now, there is demand for remote access VPN even can do a ping to access a new server within LAN, 172.57.1.10 & 172.57.1.20

But with the same VPN access, I was unable to ping the two new IP.

How can I add both IP in order to make a ping by using the same configuration of remote access VPN?

I have attached below existing config (edited version)

===

: Saved
:
ASA Version 8.0 (4)
!
hostname asalot10
names of
name 172.17.100.22 NAVNew
name 172.27.17.215 NECUser
172.47.1.10 NarayaServer description Naraya server name
name 62.80.122.172 NarayaTelco1
name 62.80.122.178 NarayaTelco2
name 172.57.1.10 IPVSSvr IPVSSvr description
name 122.152.181.147 Japan01
name 122.152.181.0 Japan02
name 175.139.156.174 Outside_Int
name 178.248.228.121 NarayaTelco3
name 172.67.1.0 VCGroup
name 172.57.1.20 IPVSSvr2
!
object-group service NECareService
Description NECareService remote
the eq https tcp service object
EQ-ssh tcp service object
response to echo icmp service object
inside_access_in deny ip extended access list all Japan02 255.255.255.0
inside_access_in ip VCGroup 255.255.255.0 allowed extended access list all
inside_access_in list extended access deny tcp object-group PermitInternet any object-group torrent1
inside_access_in list extended access allowed object-group ip PermitInternet any newspaper disable
inside_access_in list any newspaper disable extended access allowed host ip NarayaServer
inside_access_in list extended access permit ip host IPVSSvr all
inside_access_in list any newspaper disable extended access allowed host ip NAVNew
inside_access_in list extended access permit ip host 172.17.100.30 all
outside_access_in list extended access allow object-group objects NECare a NECareService-group
outside_access_in list extended access allowed host ip DM_INLINE_NETWORK_1 NarayaServer object-group
outsidein list extended access permit tcp any host Outside_Int eq https
outsidein list extended access allowed object-group rdp any host Outside_Int debug log
outsidein list extended access allowed host tcp object-group DM_INLINE_NETWORK_2 eq Outside_Int 8080
outsidein list extended access allowed host ip DM_INLINE_NETWORK_3 IPVSSvr object-group
inside_mpc list extended access allowed object-group TCPUDP any any eq www
inside_mpc list extended access permit tcp any any eq www
inside_nat0_outbound list of allowed ip extended access all 172.27.17.240 255.255.255.248
inside_nat0_outbound list extended access permit ip host NarayaServer Nry_Png object-group
inside_nat0_outbound list extended access allowed host ip IPVSSvr2 172.27.17.240 255.255.255.248
outside_cryptomap list extended access permitted ip object-group Naraya_Png-group of objects Nry_Png

Global interface 10 (external)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 10 0.0.0.0 0.0.0.0
static (inside, outside) interface tcp 8080 8080 NarayaServer netmask 255.255.255.255
static (inside, outside) tcp 3389 3389 NAVNew netmask 255.255.255.255 interface
public static tcp (indoor, outdoor) interface ssh IPVSSvr2 ssh netmask 255.255.255.255
Access-group outsidein in external interface
inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 175.139.156.173 1
Route inside 172.17.100.20 255.255.255.255 172.27.17.100 1
Route inside NAVNew 255.255.255.255 172.27.17.100 1
Route inside 172.17.100.30 255.255.255.255 172.27.17.100 1
Route inside NarayaServer 255.255.255.255 172.27.17.100 1
Route inside 172.47.1.11 255.255.255.255 172.27.17.100 1

Route inside VCGroup 255.255.255.0 172.27.17.100 1

Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define security association lifetime 28800 seconds
cryptographic kilobytes 4608000 life of the set - the association of security of the 65535 SYSTEM_DEFAULT_CRYPTO_MAP of the dynamic-map
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set 218.x.x.105 counterpart
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
outside_map map 1 lifetime of security association set seconds 28800 crypto
card crypto outside_map 1 set security-association life kilobytes 4608000
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
md5 hash
Group 2
life 86400

internal ISETANLOT10 group policy
ISETANLOT10 group policy attributes
value of server DNS 172.27.17.100
Protocol-tunnel-VPN IPSec l2tp ipsec
username, password nectier3 dPFBFnrViJi/LGbT encrypted privilege 0
username nectier3 attributes
VPN-group-policy ISETANLOT10
username password necare encrypted BkPn6VQ0VwTy7MY7 privilege 0
necare attributes username
VPN-group-policy ISETANLOT10
naraya pcGKDau9jtKgFWSc encrypted password username
naraya attribute username
VPN-group-policy ISETANLOT10
type of nas-prompt service
type tunnel-group ISETANLOT10 remote access
attributes global-tunnel-group ISETANLOT10
address lot10ippool pool
Group Policy - by default-ISETANLOT10
IPSec-attributes tunnel-group ISETANLOT10
pre-shared-key *.
tunnel-group 218.x.x.105 type ipsec-l2l
218.x.x.105 group of tunnel ipsec-attributes
pre-shared-key *.
type tunnel-group ivmstunnel remote access
tunnel-group ivmstunnel General-attributes
address lot10ippool pool
ivmstunnel group of tunnel ipsec-attributes
pre-shared-key *.
!

=====

Remote VPN access must allow the connection, but I'm guessing that your ASA does not know how to get to the two new destinations.

You have a name and a static route to the job to 172.47.1.10 Server:

name 172.47.1.10 NarayaServer description Naraya Server

route inside NarayaServer 255.255.255.255 172.27.17.100 1

.. but no equivalent for the two new hosts. As a result, all traffic of ASA destiny for them will attempt to use the default route (via the external interface).

If you add:

route inside 172.57.1.10 255.255.255.255 172.27.17.100

route inside 172.57.1.20 255.255.255.255 172.27.17.100

(assuming this is your correct entry), it should work.

Set security on 'Decline' for users of Windows/object, cannot access a drive C and d. 'Access denied'-[[problem solved]]

last updated *.

Problem is SOLVED. Read my response at the bottom of this thread.

* Update *.

Solved for drive D as now but it is still not accessible. Help the Microsoft Experts kindly. By clicking on the C drive, I got "access denied."

Hello world.

I need help. I have windows 8, 64 bit computer laptop. This system has 3 active accounts now. Account_One that is my administrator account. I have another

"limited account" created on my machine Account_two and the third one is "Guest account" account that is enabled.

Before you lend my cell phone to a friend in Account_two login I tried to restrict access to drives C and D of this Account_two which is a limited account.

While I was doing it, I put approval for object 'Windows users' 'decline '. This object is usually the last in the list of objects on the window that appears when we sail to click with the right button on C drive > properties > Security. I realized that instead of

for Account_two I did for Windows users / which means maybe Windows/users / * which covered my admin account too and that too on the drive root C.

When I connected to my Account_one account that is an administrator account, I'm not able to access drive C and D where I put the authorization of 'decline' for all the attributes as shown above to object/Windows users.

One of the folder that was on my desktop allows me to go inside the d drive as I kept this shortcut for easy access, but there is no way to navigate from c or d ' training on domestic issues. Not just me even Windows can not access important services such as 'Restore' and many others built in utilities of windows which simply will not charge blinking message windows has no access to it!

Please help how to access drive C and D for my administrator account. I am connected to this account now, but can not access drive C or d. when I go to the Security tab in the drive C and D right click Properties I get the screen it as: you must have read allowed to view the properties of this object. Click Advanced to continue. When I click on advanced, I see the "advanced security settings for local disk (d :)), where the owner is presented as: unable to display current owner." Exchange (Link) when I click on 'Change' I get the error message: cannot open access control editor access is denied.

So I put the Windows/user object to "deny" on the tab security for all read and writes, and I'm not able to access anything whatsoever since my administrator account.

Please let me know how to change access to 'allow' for c and D drive for the object user/Windows. From now there is no way to access this object by result cannot set permissions there.

Help, please.

Thank you very much.

Thank you very much.

Problem is SOLVED!

After three days of effort I was finally able to fix this mess. It took me three days after going through many similar positions as mine but no final answer or fix, so I kept

through the 'access denied' messages on this community and won an idea on what

had happened and what needed to be done. What I found that there are several hundred people

like me, who have faced this problem and there is no final official help file to explain how to fix

He IS but he MICROSFT official 'support chat' where they ask for $149 to connect remotely and difficulty

the problem!

in any case, here's how I solved my problem for people who need to fix it in case it happens to you.

How the problem began; Read my original post above on top. In short, I set the security setting to refuse to

Users of Windows/under the Security tab that comes after a right click drive then properties > Security. I put it and lost access to all readers!

How I fixed it.

Thanks to some nice people on this page of the community who have posted knowledge. A man had displayed the creation of "Administrator" "guest account of orders that I did now, I could sign out of my account and get on the 'Administrator' account with admin privileges so that I could fix it the mess on my account problem. So if you have similar problem first create the command prompt administrator account. However this only solved the problem partially as I could reverse the problem only on drive D and not on the drive C. I was able to go to security settings and set the properties 'allow' for drive D, but I was not able to read the page of security for drive C as he said I haven't read privilege he even newly created admin account.

Now if I needed the "Access denied" problem on drive C. I continued through messages of so many "access denied" here and discovered about utilities like SFC, TAKEOWN, ICACLS, but none of them worked from the command prompt I always said "access denied."

Thing was to take the mouse to the right of the screen and get this blue bar, then settings > change PC settings > General - Advanced startup-press the button -. Then he made up the blue screen, where you have the option called troubleshooting... go there and then advanced setting > look to start Windows from the command prompt. Do you have a command prompt with C:\windows\system32 on the command prompt. Here, my order was accepted both takeown and icacls. If I shot a command there: TAKEOWN /F /R C:\/a and I also tried icacls to give permissions after checking using the syntax on the command line itself. All commands ran successfully this time, but be careful what you give in the command. It's under a lien high built based on the account of Windows 8.

Takeown command executed successfully and it solved my problem. I leave the command prompt then connected to this administrator account. This time, I could go to the Security tab of the C drive and set allow it for users here. Still on some issues, I was getting no access permission, but I was asked to change it to allow me to access to and I was able to do.

For access to the C drive on the Security tab, you need to go to the 'Advanced' and change the owner too.

in any case I'm happy this is finally resolved even if I wasn't getting much help responds I used the previous positions of other threads to solve.

Since he was not an official help of WINDOWS or MICROSOFT on that page, I'm sure I did the security setting while making the methods of trial and error on my machine which may not be the right setting from the point of view of security in general, so I'll try to reset the default state machine as my problem is now solved.

So I fixed it. If you need help let me know and I'll try to help you, and I do not charge $149 or $99. ;-)

WebVPN and remote VPN access

Hello

Is there a difference between WebVPN and remote VPN access or they are the same.

Thank you.

access remote vpn consists of

-IPSEC VPN remote access. It is part of the ASA, no permit required, requires pre-installed Client from Cisco VPN IPSEC on PC

-with AnyConnect SSL VPN remote access. It requires licensing of SSL VPN on SAA. AnyConnect client can be installed automatically on the PC with the launch of web.

-with Essentials AnyConnect SSL VPN remote access. Beginning with ASA 8.2 (1), almost license $ 0. It's the same AnyConnect client as in the previous article, but it cannot be installed automatically with the launch of web. It must be previously installed as of Cisco IPSEC VPN client.

-webvpn aka clientless vpn. It is a portal HTTPS which allows HTTP connections, file sharing, telnet, RDP and much more (with smart tunnels) resources without having to install a real client on the PC. It requires licensing of SSL VPN on SAA. It cannot be used if "AnyConnect Essentials" license is activated on SAA after 8.2 (1)

Kind regards

Roman

ASA5505 can transfer clients to remote VPN access to the local network

I have currently ASA 5505 and 2911-router and I am trying to configure the VPN topology.

Can ASA5505 you transmit to remote VPN access clients LAN operated by another router?

These two cases are possible? :

(1) ASA 5505 and 2911-router are separate WAN interfaces, each connected directly to the ISP. But so can I connect an other interfaces LAN of ASA 5505 in a switch managed by 2911 router customers to distance-SSL-VPN to inject into the local network managed by the router?
(2) ASA 5505 is behind router-2911. May 2911 router address public ip or public ip address VPN-access attempts have directly be sent to ASA 5505 when there is only a single public ip address address available?
Long put short, ASA 5505 can inject its clients to remote-access-VPN as one of the hosts on the local network managed by 2911-router?
Thank you.

I could help you more if you can explain the purpose of this configuration and connectivity between the router and ASA.

You can activate the reverse route on the dynamic plane on the SAA. The ASA will install a static route to the customer on the routing table. You can use a routing protocol to redistribute static routes to your switch on the side of LAN of the SAA.

Console Remote button grayed out for M605 blades seen CMC

Hello

When connected to the CMC and look at a preview/properties/server status, M605 blades show the Remote Console as grayed out button, but the button iDRAC is normal.

At the start of the iDRAC a blade, the Console tab can be selected and the Console launched very well. So nothing wrong with the connection to the console.
- How the key of Remote Console can be enabled from the CMC? Why is greyed out?
(BTW, in a chassis mixed with M610 and M605, of the M610 all show the button Console remotely normally, but the M605 are greyed out)?

Thx for your help,

John Bradshaw

John,

The M605 is a blade of more early liberated. The M610 is actually cut, everything that follows the M610 will support the launch of the Console remotely from the CMC. The M600 and M605 does not support, but can be launched from the Drac.

Console remote vCenter access (NAT problem)?

Similar Questions

Maybe you are looking for