WebVPN and remote VPN access

Similar Questions

• WebVPN and remote vpn, ssl vpn anyconnect

  Hi all

  Differences between webvpn and remote vpn, ssl vpn anyconnect
  All require a separate license?

  Thank you

  Hello

  The difference between the webvpn and SSL VPN Client is the WebVPN to use SSL/TLS and port

  send through a java application to support the application, it also only supports TCP for unicast traffic, no ip address

  address is assigned to the customer, and the navigation on the web in the tunnel is made with a SSL

  Web-mangle that allows us stuff things in theSSL session.

  SSL VPN (Anyconnect) Client is a client of complete tunneling using SSL/TCP, which installs an application on the computer and

  envelopes vpn traffic in the ssl session and thus also an assigned ip address has the

  tunnel's two-way, not one-way.   It allows for the support of the application on the

  tunnel without having to configure a port forward for each application.

  AnyConnect is a client of new generation, which has replaced the old vpn client and can be used as long as the IPSEC vpn ssl.

  For anyconnect licenses please see the link below:

  http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...

  Kind regards

  Kanwal

• Site2Site and remote VPN

  I have a site2site between PIX506 and 877 router VPN. Site A has PIX506 and Site B router a in 877. I configured site2site VPN and it worked fine. I also configured remote VPN on PIX 506 so that the remote user can access A site. But when I configure remote VPN on PIX506 site2site VPN works and both sides can ping each other. But site B users cannot access any resource network or application of the SiteA while site A can access resources of site B. After removing remote VPN site configuration B can access the resources of the Site I joined the configuration of the two sites. Someone help me please site2site and remote VPN work at the same time.

  Please forgive me for not reading every line.

  an add-on quick about the pix configuration:

  change "isakmp key * address 213.181.169.8 netmask 255.255.255.255" at "isakmp key * address 213.181.169.8 netmask 255.255.255.255 No.-xauth No. config-mode.

• ASA5505 can transfer clients to remote VPN access to the local network

  I have currently ASA 5505 and 2911-router and I am trying to configure the VPN topology.

  Can ASA5505 you transmit to remote VPN access clients LAN operated by another router?

  These two cases are possible? :

  (1) ASA 5505 and 2911-router are separate WAN interfaces, each connected directly to the ISP. But so can I connect an other interfaces LAN of ASA 5505 in a switch managed by 2911 router customers to distance-SSL-VPN to inject into the local network managed by the router?
  (2) ASA 5505 is behind router-2911. May 2911 router address public ip or public ip address VPN-access attempts have directly be sent to ASA 5505 when there is only a single public ip address address available?
  Long put short, ASA 5505 can inject its clients to remote-access-VPN as one of the hosts on the local network managed by 2911-router?
  Thank you.

  I could help you more if you can explain the purpose of this configuration and connectivity between the router and ASA.

  You can activate the reverse route on the dynamic plane on the SAA. The ASA will install a static route to the customer on the routing table. You can use a routing protocol to redistribute static routes to your switch on the side of LAN of the SAA.

• Remote VPN access - add new internal IP address

  Hello

  I have an existing configuration of Cisco VPN client in ASA 5510 for remote access.

  -------------------------------------

  Name of the Group: ISETANLOT10

  Group password: xxxx
   
  IP pool: lot10ippool, 172.27.17.240 - 172.27.17.245
   
  enycrption: 3DES
  authentication: SHA
  ------------------------------------
  the connection was successful, and I was able to ping to the internal server 172.47.1.10.
  Now, there is demand for remote access VPN even can do a ping to access a new server within LAN, 172.57.1.10 & 172.57.1.20
  But with the same VPN access, I was unable to ping the two new IP.
  How can I add both IP in order to make a ping by using the same configuration of remote access VPN?
  I have attached below existing config (edited version)
   
  ===

  : Saved
  :
  ASA Version 8.0 (4)
  !
  hostname asalot10
  names of
  name 172.17.100.22 NAVNew
  name 172.27.17.215 NECUser
  172.47.1.10 NarayaServer description Naraya server name
  name 62.80.122.172 NarayaTelco1
  name 62.80.122.178 NarayaTelco2
  name 172.57.1.10 IPVSSvr IPVSSvr description
  name 122.152.181.147 Japan01
  name 122.152.181.0 Japan02
  name 175.139.156.174 Outside_Int
  name 178.248.228.121 NarayaTelco3
  name 172.67.1.0 VCGroup
  name 172.57.1.20 IPVSSvr2
  !
  object-group service NECareService
  Description NECareService remote
  the eq https tcp service object
  EQ-ssh tcp service object
  response to echo icmp service object
  inside_access_in deny ip extended access list all Japan02 255.255.255.0
  inside_access_in ip VCGroup 255.255.255.0 allowed extended access list all
  inside_access_in list extended access deny tcp object-group PermitInternet any object-group torrent1
  inside_access_in list extended access allowed object-group ip PermitInternet any newspaper disable
  inside_access_in list any newspaper disable extended access allowed host ip NarayaServer
  inside_access_in list extended access permit ip host IPVSSvr all
  inside_access_in list any newspaper disable extended access allowed host ip NAVNew
  inside_access_in list extended access permit ip host 172.17.100.30 all
  outside_access_in list extended access allow object-group objects NECare a NECareService-group
  outside_access_in list extended access allowed host ip DM_INLINE_NETWORK_1 NarayaServer object-group
  outsidein list extended access permit tcp any host Outside_Int eq https
  outsidein list extended access allowed object-group rdp any host Outside_Int debug log
  outsidein list extended access allowed host tcp object-group DM_INLINE_NETWORK_2 eq Outside_Int 8080
  outsidein list extended access allowed host ip DM_INLINE_NETWORK_3 IPVSSvr object-group
  inside_mpc list extended access allowed object-group TCPUDP any any eq www
  inside_mpc list extended access permit tcp any any eq www
  inside_nat0_outbound list of allowed ip extended access all 172.27.17.240 255.255.255.248
  inside_nat0_outbound list extended access permit ip host NarayaServer Nry_Png object-group
  inside_nat0_outbound list extended access allowed host ip IPVSSvr2 172.27.17.240 255.255.255.248
  outside_cryptomap list extended access permitted ip object-group Naraya_Png-group of objects Nry_Png

  Global interface 10 (external)
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 10 0.0.0.0 0.0.0.0
  static (inside, outside) interface tcp 8080 8080 NarayaServer netmask 255.255.255.255
  static (inside, outside) tcp 3389 3389 NAVNew netmask 255.255.255.255 interface
  public static tcp (indoor, outdoor) interface ssh IPVSSvr2 ssh netmask 255.255.255.255
  Access-group outsidein in external interface
  inside_access_in access to the interface inside group
  Route outside 0.0.0.0 0.0.0.0 175.139.156.173 1
  Route inside 172.17.100.20 255.255.255.255 172.27.17.100 1
  Route inside NAVNew 255.255.255.255 172.27.17.100 1
  Route inside 172.17.100.30 255.255.255.255 172.27.17.100 1
  Route inside NarayaServer 255.255.255.255 172.27.17.100 1
  Route inside 172.47.1.11 255.255.255.255 172.27.17.100 1

  
  Route inside VCGroup 255.255.255.0 172.27.17.100 1

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define security association lifetime 28800 seconds
  cryptographic kilobytes 4608000 life of the set - the association of security of the 65535 SYSTEM_DEFAULT_CRYPTO_MAP of the dynamic-map
  card crypto outside_map 1 match address outside_cryptomap
  card crypto outside_map 1 set 218.x.x.105 counterpart
  card crypto outside_map 1 set of transformation-ESP-3DES-SHA
  outside_map map 1 lifetime of security association set seconds 28800 crypto
  card crypto outside_map 1 set security-association life kilobytes 4608000
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 30
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400

  internal ISETANLOT10 group policy
  ISETANLOT10 group policy attributes
  value of server DNS 172.27.17.100
  Protocol-tunnel-VPN IPSec l2tp ipsec
  username, password nectier3 dPFBFnrViJi/LGbT encrypted privilege 0
  username nectier3 attributes
  VPN-group-policy ISETANLOT10
  username password necare encrypted BkPn6VQ0VwTy7MY7 privilege 0
  necare attributes username
  VPN-group-policy ISETANLOT10
  naraya pcGKDau9jtKgFWSc encrypted password username
  naraya attribute username
  VPN-group-policy ISETANLOT10
  type of nas-prompt service
  type tunnel-group ISETANLOT10 remote access
  attributes global-tunnel-group ISETANLOT10
  address lot10ippool pool
  Group Policy - by default-ISETANLOT10
  IPSec-attributes tunnel-group ISETANLOT10
  pre-shared-key *.
  tunnel-group 218.x.x.105 type ipsec-l2l
  218.x.x.105 group of tunnel ipsec-attributes
  pre-shared-key *.
  type tunnel-group ivmstunnel remote access
  tunnel-group ivmstunnel General-attributes
  address lot10ippool pool
  ivmstunnel group of tunnel ipsec-attributes
  pre-shared-key *.
  !

  =====

  Remote VPN access must allow the connection, but I'm guessing that your ASA does not know how to get to the two new destinations.

  You have a name and a static route to the job to 172.47.1.10 Server:

  name 172.47.1.10 NarayaServer description Naraya Server

  route inside NarayaServer 255.255.255.255 172.27.17.100 1

  .. but no equivalent for the two new hosts. As a result, all traffic of ASA destiny for them will attempt to use the default route (via the external interface).

  If you add:

  route inside 172.57.1.10 255.255.255.255 172.27.17.100

  route inside 172.57.1.20 255.255.255.255 172.27.17.100

  (assuming this is your correct entry), it should work.

• You try to run a Site to site VPN and remote VPN from the same IP remotely

  We currently have a site to site VPN configuration between our offices call center and a 3rd party that allows them to access our training to their employees to use environment while being trained on our systems. This tunnel is running between our ASA and their ASA without problem; However, when we have managers come out to the call center, they are unable to use remote VPN to access our office.

  Apparently the same IP peer remote that we use for our site to the other tunnel is the same IP that our managers use to access the internet when they are on-site with the customer. When I look at the logs it shows the VPN attempt and then I get treatment Information Exchange has failed. So from what I can understand when our managers are trying to connect to our firewall from the same IP address as the counterpart of site to site it automatically tries to create a tunnel, according to the information of the site to the other tunnel. If our managers are anywhere else, they can connect through remote VPN with no problems.

  My question is if anyone knows of a way to make the firewall allow VPN site to site and remote connections with the same remote IP address.

  Hi John,.

  Basically, in older versions, when you hit a static encryption card and you does not match this static encryption completely map the connection continues until the dynamic encryption card. For this reason, you can connect your IPSec clients before. A bug has been opened on this vulnerability.

  CSCuc75090  Details of bug

  The crypto IPSec Security Association are created by dynamic crypto map to static peers

  Symptom:

  When a static VPN peer adds all traffic to the ACL crypto, a surveillance society is based even if the pair IP is not allowed in the acl to the main façade encryption. Are these SA finally put in correspondence and commissioning the dynamic crypto map instance.

  Conditions:

  It was a planned design since the first day that allowed customers to fall through in the case of static crypto map did not provide a necessary cryptographic services.

  The SA must be made from a peer configured statically and a dynamic crypto map instance must be configured on the receiving end.

  Workaround solution:

  N/A

  Some possible workarounds are:

  Configure a static nat device when you try to use the remote VPN if the firewall remotely will be hit with a different public IP address. It would be a good solution, but it will depend on how many ip addresses public you have available, if you really want one of these ip addresses for that access.

  Also, I thought you could use AnyConnect instead of the IPSec VPN client. I don't know how many users need to connect from your PC to the remote site, but the ASA has 2 licenses SSL available that you could use. Because Anyconnect uses the SSL protocol, it won't have a problem on your environment.

  Below some information:

  http://www.Cisco.com/c/en/us/TD/docs/security/ASA/asa84/configuration/guide/asa_84_cli_config/vpn_anyconnect.html

  Hope this helps,

  Luis.

• NAT overlapping with remote VPN access

  Hi all

  My client has an ASA 5510 at the main location. We're shooting for their remote access VPN SSL needs. 30 or so remote users.

  The problem is that the main site has a number of network 192.168.1.0/24. The number of Linksys routers bought on shelf at any store of default.

  Obviously, by default, it does not work. When users connect to the VPN from home, it connects but network resources are not available.

  I read about overlapping NAT with tunnels of site to another, but that all remote access? Is it possible as well?

  Any help to point me in the right direction would be much appreciated.

  Thank you!

  Look at the PIX / ASA 7.x and later: VPN Site to Site (L2L) with the example of setting up IPsec policy NAT (overlapping of private networks) for more information

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808c9950.shtml

• INTERNET VIA REMOTE VPN ACCESS

  We have a customer who wants to route all internet traffic to their remote sites of their internet connection to Headquarters. In other words, when users connect to corporate headquarters using Cisco VPN client on their PC, we need to route all internet traffic on through the firewall of the headquarters. Head office is running a ASA place all the VPN configuration. We have a number of virtual private network set up for this customer but would welcome suggestions as to the best way to configure this particular step.

  Thank you very much.

  Hello

  This looks like back or Hairpining for VPN clients, so they could access the Internet through the tunnel.

  In which case it is a ASA 8.2 or earlier:

  permit same-security-traffic intra-interface

  NAT (outside) 1 192.168.1.0 255.255.255.0---> range of IP addresses assigned to VPN clients.

  Global 1 interface (outside)

  In which case it is an ASA 8.3 or later:

  permit same-security-traffic intra-interface

  network vpn-pool objects

  subnet 192.168.1.0 255.255.255.0

  dynamic NAT interface (outdoors, outdoor)

  !

  On the configuration of VPN:

  mypolicy group policy attributes

  Split-tunnel-policy tunnelall

  !
  tunnel-group mytunnel General-attributes

  MyPolicy defaul-group-policy

  !

  Benefits:

  1-Internet access is controlled by the ASA.

  Disadvantages:

  1 Internet connection of the ASA is severely affected, it will be used by VPN clients to access the Internet.

  Alternative solution:

  Send all traffic to a Layer 3 internal device or a server that has an external Internet connection, so the ASA forwards all traffic to this device, if this device is able to perform web filterting advance as the unit of Microsoft IIS, then you would have a powerful way to control your users and that they access, thus preventing sites such undesirable sites for adults and animation.

  To do this, all you need is:

  Route within 0 0 192.168.10.1 tunnele---> where the 192.168.10.1 corresponds to the internal device responsible for providing Internet.

  * Remember that this device must have an external connection for Internet access, not on the SAA.

  Let me know.

  Portu.

  Please note any workstation that will be useful.

  Post edited by: Javier Portuguez

• is it possible this with remote vpn access?

  Hello

  I have access to my corporate network through the VPN Cisco (software) customer and it goes through the vpn to access configuration remote ipsec on an ASA 5510. Everything works fine.

  But now that connect to the corporate network users also need access to remote sites connected by tunnels VPN site to site networks: tunnels IPSec between mentioned ASA5510 and distance ASA5510s and ASA5505s in the branches.

  Is this possible?

  If so what shoud I consider make it works?

  My setup looks like

  business network: 10.1.1.0/24

  Remote vpn clients receive the ip addresses of: 10.0.5.0/28

  Branch on the remote 1 network: 10.1.10.0/24

  network of remote sites 2: 10.1.20.0/24

  3 remote site network: 10.1.30.0/24

  There rule for NAT exemption which exempts the networks 10.1.10.0/24, 10.1.20.0/24, 10.1.30.0/24

  All traffic on the local network 10.1.1.0/24 have complete ip connectivity with all networks in the branches. The PROBLEM is that the remote vpn clients can reach only local network 10.1.1.0/24, but not the remote networks.

  The ASAs in remote sites has created NAT exemption to the two local network 10.1.1.0/24 and network 10.0.5.0/28 remote access clients, but as I said, it won't. Help, please!

  Thanks in advance!

  Zoran

  Yes, you can...

  Let's take 1 remote sites for example network: network of agencies 1 (10.1.10.0/24):

  Company ASA:

  -If you have split tunnel configured for the VPN Client, you must also add the remote site network in the list (10.1.10.0/24).

  -Crypto ACL between the company ASA and ASA 1 remote sites must have added the following:

  10.0.5.0 ip access list allow 255.255.255.240 10.1.10.0 255.255.255.0

  -' same-security-traffic permit intra-interface' must be configured

  On the remote control of the branch 1 ASA:

  -Crypto ACL between remote branch 1 ASA and company ASA must have added the following:

  ip 10.1.10.0 access list allow 255.255.255.0 10.0.5.0 255.255.255.240

  -Rule of exemption NAT to exempt traffic:

  ip 10.1.10.0 access list allow 255.255.255.0 10.0.5.0 255.255.255.240

  Clear the tunnels of both ends and test the connectivity.

  I hope this helps.

• Cisco ASA 5505 remote VPN access to the local network

  I have installed two ASA 5505 VPN site to site that works perfectly.  Now, I also need to have 1 customer site to remote access VPN with Cisco VPN dialer.  I can get the VPN dialer to connect the VPN and get a VPN IP address, but I do not have access to the remote network.  can someone take a look and see what I'm missing?  I have attached the ASA running config.

  Apologize for the misunderstanding.

  To access the remote vpn client 10.10.100.x subnet, the vpn-filter ACL is the opposite.

  Please please share the following ACL:

  FROM: / * Style Definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-marge-haut : 0 cm ; mso-para-marge-droit : 0 cm ; mso-para-marge-bas : 10.0pt ; mso-para-marge-gauche : 0 cm ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  outside_cryptomapVPN list of allowed ip extended access any 10.10.20.0 255.255.255.224

  TO:

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-marge-haut : 0 cm ; mso-para-marge-droit : 0 cm ; mso-para-marge-bas : 10.0pt ; mso-para-marge-gauche : 0 cm ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  outside_cryptomapVPN to access extended list ip 10.10.20.0 allow 255.255.255.224 all

  Hope that helps.

• IPsec over UDP - remote VPN access

  Hello world

  The VPN client user PC IPSEC over UDP option is checked under transport.

  When I check the details of the phase 1 of IKE ASDM of user login, it shows only UDP 500 port not port 4500.

  Means that user PC VPN ASA there that no device in question makes NAT.

  What happens if we checked the same option in the client IPSEC VPN - over UDP and now, if we see the port UDP 4500 under IKE phase 1 Connection Details

  This means that there is now ASA a NAT device VPN Client PC, but he allows IKE connection phase 1?

  Concerning

  MAhesh

  Hello Manu,

  I suggest to use the following commands on your ASA have a look at these ports as the test of VPN connections. The command that you use depends on your level of software as minor changes in the format of the command

  View details remote vpn-sessiondb

  view sessiondb-vpn remote detail filter p-ipaddress

  Or

  View details of ra-ikev1-ipsec-vpn-sessiondb

  display the filter retail ra-ikev1-ipsec-vpn-sessiondb p-ipaddress

  These will provide information on the type of VPN Client connection.

  Here are a few out of different situations when connecting with the VPN Client

  Dynamic PAT - no Transparent on the Client VPN tunnel

  • Through the VPN connections do not work as connects via PAT without Transparent tunnel

  Username: Index: 22

  Public IP address 10.0.1.2 assigned IP::

  Protocol: IPsec IKEv1

  IKEv1:

  Tunnel ID: 22.1

  The UDP Src Port: 18451 UDP Dst Port: 500

  IKE Neg Mode: Aggressive Auth Mode: preSharedKeys

  Encryption: AES 256 hash: SHA1

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 28551 seconds

  Group D/H: 2

  Name of the filter:

  Client OS: Windows NT Client OS worm: 5.0.07.0290

  IPsec:

  Tunnel ID: 22.2

  Local addr: 0.0.0.0/0.0.0.0/0/0

  Remote addr: 10.0.1.2/255.255.255.255/0/0

  Encryption: AES 256 hash: SHA1

  Encapsulation: Tunnel

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 28551 seconds

  Idle Time Out: 30 Minutes idling left: 25 Minutes

  TX Bytes: 0 Rx bytes: 0

  TX pkts: Rx Pkts 0: 0

  Dynamic PAT - Transparent tunnel (NAT/PAT) on the VPN Client

  • Via VPN connections work as we use Tunneling Transparent when we train the dynamic VPN Client through PAT connection

  Username: Index: 28

  Public IP address 10.0.1.2 assigned IP::

  Protocol: IKEv1 IPsecOverNatT

  IKEv1:

  Tunnel ID: 28.1

  The UDP Src Port: 52825 UDP Dst Port: 4500

  IKE Neg Mode: Aggressive Auth Mode: preSharedKeys

  Encryption: AES 256 hash: SHA1

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 28784 seconds

  Group D/H: 2

  Name of the filter:

  Client OS: Windows NT Client OS worm: 5.0.07.0290

  IPsecOverNatT:

  Tunnel ID: 28.2

  Local addr: 0.0.0.0/0.0.0.0/0/0

  Remote addr: 10.0.1.2/255.255.255.255/0/0

  Encryption: AES 256 hash: SHA1

  Encapsulation: Tunnel

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 28784 seconds

  Idle Time Out: 30 Minutes idling left: 30 Minutes

  TX Bytes: 360 bytes Rx: 360

  TX pkts: 6 Pkts Rx: 6

  Dynamics PAT, Transparent IPsec (TCP) on the Client VPN tunnel

  • Via VPN connections work as we use Tunneling Transparent when we train the dynamic VPN Client through PAT connection

  Username: Index: 24

  Public IP address 10.0.1.2 assigned IP::

  Protocol: IKEv1 IPsecOverTCP

  IKEv1:

  Tunnel ID: 24.1

  The UDP Src Port: 20343 UDP Dst Port: 500

  IKE Neg Mode: Aggressive Auth Mode: preSharedKeys

  Encryption: AES 256 hash: SHA1

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 28792 seconds

  Group D/H: 2

  Name of the filter:

  Client OS: Windows NT Client OS worm: 5.0.07.0290

  IPsecOverTCP:

  Tunnel ID: 24,2

  Local addr: 0.0.0.0/0.0.0.0/0/0

  Remote addr: 10.0.1.2/255.255.255.255/0/0

  Encryption: AES 256 hash: SHA1

  Encapsulation: Tunnel TCP Src Port: 20343

  The TCP Dst Port: 10000

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 28792 seconds

  Idle Time Out: 30 Minutes idling left: 30 Minutes

  TX Bytes: 180 bytes Rx: 180

  TX pkts: Rx 3 Pkts: 3

  Static NAT - no Transparent on the Client VPN tunnel

  • VPN Client connections to the LAN work because our VPN Client has a static NAT configured for its local IP address. This allows the ESP without encapsulation through the device doing the static NAT. You must allow the ESP traffic through the NAT device of management of the device VPN or configure VPN connections inspection if there is an ASA acting as the NAT device.

  Username: Index: 25

  Public IP address 10.0.1.2 assigned IP::

  Protocol: IPsec IKEv1

  IKEv1:

  Tunnel ID: 25.1

  The UDP Src Port: 50136 UDP Dst Port: 500

  IKE Neg Mode: Aggressive Auth Mode: preSharedKeys

  Encryption: AES 256 hash: SHA1

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 28791 seconds

  Group D/H: 2

  Name of the filter:

  Client OS: Windows NT Client OS worm: 5.0.07.0290

  IPsec:

  Tunnel ID: 25.2

  Local addr: 0.0.0.0/0.0.0.0/0/0

  Remote addr: 10.0.1.2/255.255.255.255/0/0

  Encryption: AES 256 hash: SHA1

  Encapsulation: Tunnel

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 28791 seconds

  Idle Time Out: 30 Minutes idling left: 30 Minutes

  TX Bytes: 120 bytes Rx: 120

  TX pkts: Rx 2 Pkts: 2

  Static NAT - Transparent tunnel (NAT/PAT) on the VPN Client

  • The VPN Client connections are functioning normally. Even if the host Staticly using a NAT VPN Client does not need UDP encapsulation it is always used if your connection of the VPN Client profile is configured to use (tab in the Transport of the client software)

  Username: Index: 26

  Public IP address 10.0.1.2 assigned IP::

  Protocol: IKEv1 IPsecOverNatT

  IKEv1:

  Tunnel ID: 26.1

  The UDP Src Port: 60159 UDP Dst Port: 4500

  IKE Neg Mode: Aggressive Auth Mode: preSharedKeys

  Encryption: AES 256 hash: SHA1

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 28772 seconds

  Group D/H: 2

  Name of the filter:

  Client OS: Windows NT Client OS worm: 5.0.07.0290

  IPsecOverNatT:

  Tunnel ID: 26.2

  Local addr: 0.0.0.0/0.0.0.0/0/0

  Remote addr: 10.0.1.2/255.255.255.255/0/0

  Encryption: AES 256 hash: SHA1

  Encapsulation: Tunnel

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 28772 seconds

  Idle Time Out: 30 Minutes idling left: 29 Minutes

  TX Bytes: 1200 bytes Rx: 1200

  TX pkts: Rx 20 Pkts: 20

  Static NAT - Transparent tunnel on the VPN Client (IPsec, TCP)

  • The VPN Client connections are functioning normally. Even if the host Staticly using a NAT VPN Client does not need TCP encapsulation it is always used if your connection of the VPN Client profile is configured to use (tab in the Transport of the client software)

  Username: Index: 27

  Public IP address 10.0.1.2 assigned IP::

  Protocol: IKEv1 IPsecOverTCP

  IKEv1:

  Tunnel ID: 27.1

  The UDP Src Port: 61575 UDP Dst Port: 500

  IKE Neg Mode: Aggressive Auth Mode: preSharedKeys

  Encryption: AES 256 hash: SHA1

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 28790 seconds

  Group D/H: 2

  Name of the filter:

  Client OS: Windows NT Client OS worm: 5.0.07.0290

  IPsecOverTCP:

  Tunnel ID: 27.2

  Local addr: 0.0.0.0/0.0.0.0/0/0

  Remote addr: 10.0.1.2/255.255.255.255/0/0

  Encryption: AES 256 hash: SHA1

  Encapsulation: Tunnel TCP Src Port: 61575

  The TCP Dst Port: 10000

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 28790 seconds

  Idle Time Out: 30 Minutes idling left: 30 Minutes

  TX Bytes: 120 bytes Rx: 120

  TX pkts: Rx 2 Pkts: 2

  VPN device with a public IP address directly connected (as a customer VPN) to an ASA

  Username: Index: 491

  Assigned IP: 172.31.1.239 public IP address:

  Protocol: IPsec IKE

  IKE:

  Tunnel ID: 491.1

  The UDP Src Port: 500 UDP Dst Port: 500

  IKE Neg Mode: Aggressive Auth Mode: preSharedKeys

  Encryption: 3DES hash: SHA1

  Generate a new key Int (T): 86400 seconds given to the key Left (T): 71016 seconds

  Group D/H: 2

  Name of the filter:

  IPsec:

  Tunnel ID: 491.2

  Local addr: 0.0.0.0/0.0.0.0/0/0

  Remote addr: 172.31.1.239/255.255.255.255/0/0

  Encryption: AES128 hash: SHA1

  Encapsulation: Tunnel

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 12123 seconds

  Generate a new key Int (D): 4608000 K-bytes given to the key Left (D): 4607460 K-bytes

  Idle Time Out: 0 Minutes idling left: 0 Minutes

  TX Bytes: bytes 3767854 Rx: 7788633

  TX pkts: 56355 Pkts Rx: 102824

  Above are examples for your reference. I must also say that I am absolutely not an expert when it comes to virtual private networks in general. I had to learn two firewall/vpn basically on my own, as during my studies, we had no classes related to them (which was quite strange).

  While I learned how to set up VPN and troubleshoot them I think I missed on the basic theory. I had plans to get the title Associates CCNA/CCNP certifications but at the moment everything is possible. Don't have the time for it.

  I guess that you already go to the VPN security CCNP Exam?

  Hope this helps and I hope that I didn't get anything wrong above

  -Jouni

• PORT of Configuration.DEFAULT of ASA AnyConnect remote VPN access.

  Hello!!! Now, I need to configure the AnyConnect VPN remote access. And I have a question.

  The default 443 AnyConnect port, but the port is occupied on SAA. We use this port for another application.

  How to change the port to connect? Is this true? Thank you!!!

  Hi, please add the following configuration:

  1. Enable the WebVPN on the SAA feature:

     ASA(config)#webvpn

  2. Enable WebVPN services for the external interface of the ASA:

     ASA(config-webvpn)#enable outside

  3. Allow the ASA to listen WebVPN traffic on the custom port number:

     ASA(config-webvpn)#port <1-65535>

• Don't host any remote VPN access

  Hello guys,.

  I have an ASA 5505 with two tunnels, a Site to Site (between two ASA 5505), and also, I added a remote access VPN using the factor of Cisco's VPN. The thing I discovered is that the Site to Site connection, I can reach the hosts of the LAN, but the use of the VPN Client I only can reach the inside Interface of the ASA, but not for the hosts.

  Something is perhaps missing from my ACL but I was not able to determine what it is. You give me a hand on this?

  Attached my config file, and the LAN behind the ASA consist in a couple of VLAN segment 192.168.0.0 24 receives the Client VPN IP to the 10.10.10.X segment

  Thanks in advance,

  Hi David,

  You are missing a statement of NAT exemption.

  Need to add this:

  access-list sheep extended 10.10.10.0 any allowed ip 255.255.255.0

• Cannot TFTP remote VPN access

  I am accessing a remote site with a VPN client. I am trying to download the config of the router for this laptop remotely with a server tftp on it.

  This does not work, and I think it is because it is the supply of the external interface. Is this correct? If so how to fix it?

  Thanks for help.

  Antony

  To fix this problem set up the router with ip tftp source interface

  This will get the router to use the address of the interface specified as the source for TFTP.

  HTH

  Rick

• Remote VPN access

  I'm trying to migrate some VPN remote access for some directors of the power of a router to an ASA 5500. The profile I'm using is vpnclient. When I add the access lists to join networks (10,200 and 10.25) inside what it appears on the route print command is the network of 10,200. I can ping to a server or a client, but cannot ping any network device. I can't ping any device in the subnet 10.25. Any help in this would be greatly appreciated. Here is the config.

  Hi Mitch,

  Ensure that subnet 10.25.x.x pass thru nat (inside) 0 for example access list 102

  HTH

  Mike