Context of sequence of LabVIEW user interface access

Similar Questions

• Event generation of click for the Run button programmatically in LabVIEW User Interface

  Hello

  I use the user interface of LabVIEW Simple (Simple OI - VI.vi first level) for my application teststand with small changes. Here, I don't want to click the button run every time. Generate the click event of the Run button (which tringgers the TS gear) by programming the interfacr VI user or is there a method for tringger TS gear?

  More information:

  LabVIEW worm: LabVIEW 2010

  TestStand worm: TestStand 2010 SP1

  My sequence Run point enry's 'Test DUT'

  Thank you

  Alaka

  Hi Adarsh,

  There's a DoClick method for the TS user interface buttons! Just wire the ref button to invoke node and locate the DoClick method.

  Kind regards

• The Web of LabVIEW user interface directly to the sensor with Ethernet connection

  Hello

  Is it possible to connect to the interface user Web of LabVIEW directly to a sensor with Ethernet connection?

  By directly, I mean without using any Web Service LabVIEW VI.

  Thank you

  Marcelo

  Hello

  The only communication with other devices using the Web user interface designer is through web services, either motorized or not LabVIEW. To connect with a sensor with the generator of the user Web interface without using LabVIEW, the sensing device must be accessible via HTTP and give you a way to read its data using XML web services based on.

• How can I join buttons visible teststand keyboard shortcuts in a labview user interface

  On a normal labview VI, it is possible to configure the desired for example key navigation options assign a keyboard shortcut to a control. Is it possible somehow to assign a keyboard shortcut to the visible controls ActiveX Teststand i.eg. a basic custom user interface labview Teststand button?

  Help, please

  You may be able to do by cloning of each button, assign a shortcut to the clone, and then firing an event and call the method "DoClick' of the TestStand button - I say maybe because I can't verify the DoClick method will do what you want.

  Obviously, you can hide the clones on the front panel if necessary.

  

• Simple TestStand in LabVIEW user interface

  Hello community,

  I design a user interface for Teststand using the simple example of vi. The name of the file is VI.vi of first level

  I am trying to understand works vi inorder to make changes and ran into a few questions that I was hoping someone could answer for me please.

  To begin, I add my file sequence and click on 'Test DUT'. Then a dialog box appears asking to enter the serial number of the UUT, where and what are the causes that to happen in the code? After I entered my serial number it turns my code sequence and at the end an another message specifying in a green or red if the UUT success or failure. Where and what are the causes of success/failure boxes happen in the code?

  Thank you

  Kevin

  If you had posted this on the forum of TestStand, you would be probably got some of the answers better.

  But in the meantime, you need to open the SequentialModel.seq (or what is process model you use) and navigate to the entry Point of execution sequence, you use.  In this case, click Test UUT, the icon in the list of sequence and track the flow of test.

  With respect to the banner that appears after execution of USE test.  The banner is implemented as a DLL in the PostUUT callback.  It is based on the status of the MainSequence callback result.  It is the result of the test that you started by test DUT.

  The best advice I can give you is to go through the sequence of process template file and learn that it is not an easy task, but worth the effort.

  Thank you

  PH

• Launch by programming a sequence file don't switch for execution in the user interface

  TestStand 4.2

  LabVIEW 2009

  Windows Vista Business 32-bit

  My movie file uses a SequenceFileLoad reminder to start his own execution automatically by using the entry point TestUUTs. This is accomplished by calling the Engine.NewExecution method. The problem I have is that my custom LabVIEW user interface does not switch to the view of execution when execution begins. If I manually start the execution using the TestUUTs key, the point of view of execution is displayed.

  In my interface user, changing the display of the sequence at the sight of the execution is done in the event callback, DisplayExecution, and the StartExecution event reminder. I also tried the ExecutionChanged event reminder, but realized that it did not apply in this case. The complex UI that comes with TestStand works correctly and, as far as I know, I use the same event reminders to manage change in my user interface.

  Any ideas? What Miss me?

  Thank you

  Toby

  CLD, CTD

  I realized what was going on. I was to switch it on the SequenceView using the ExecutionClosed callback, but was not checking the number of executions that have been opened. Opening my file of sequence autolaunching would open two executions, one to open the file and the actual execution of the file. As soon as the file has been opened, the first run was closing my UI to return to the display of the trigger sequence. Execution else had already begun the execution of the sequence file so he would continue to run in view of the execution, but I didn't see it.

  I now use ApplicationManager.Executions.Count and only to switch back to the SequenceView if it was not open execution.

• How to call sequence into LabVIEW, by providing the path of the sequence files.

  Hello

  Please give me a solution for call sequence from the API ActiveX LabVIEW file by entering the path of the LabVIEW user interface sequence.

  Thank you

  Wherry

  Here is a link I gave some pointers on how to run a file opened via Single Pass sequence.

  http://forums.NI.com/T5/NI-TestStand/direct-execution-of-the-sequence-when-UI-launches/m-p/2000819#M...

  How are you going to start this sequence is the user who selects the sequence on the disk?    Is already open in a SequenceViewMgr control?

  An operator interface would be more applicable to your situation?

  Thank you

  PH

• Using ActiveX controls to the old user interface

  I tried to build a User Interface for TestStand 4.1.1 using LabView 8.6.1 (on Windows XP)

  However, ActiveX controls keep showing in the old non - 3d "block" style.

  

  This seems to be a problem when you build a new exe. If you use the included UI (Full Featured) in TestStand it appears correctly.

  

  I was able to replacte this problem on two other development systems (a new windows XP, LabVIEW 8.6.1 & TestStand 4.1.1 install).

  (1) take a copy of the full-functional UI of LabVIEW.

  (2) open the project file

  (3) rebuild the exe file

  It's only a problem when you use the exe file. When you run from the LabVIEW development system it looks good.

  Hi Simon,.

  For your UI to take on XP
  Theme controls, you will need to place a manifest file that specifies the activex control topics in the same
  directory as your executable file. TestStand comes with a manifest file for
  INTERFACE c# you can also use for the UI of LabVIEW. Just go to the \User Interfaces\Simple\CSharp and copy the file TestExec.exe.manifest in the directory of the LabVIEW User Interface executables.

  Note that the manifest file must have the same name as your executable file LabVIEW UI. For example, if you name your user interface, "MyCustomTSUI.exe", you will need to name the manifest file 'MyCustomTSUI.exe.manifest '.

  Please let me know if this solves your problem or if you have other questions. Thank you!

• How to get the value of the global variable to test in the user interface of labview?

  Hello.

  Can someone please share examples and tell me how access the global variable to test using the interface labview user.

  I found some references and obtained from the method.

  I sent the link below

  https://decibel.NI.com/content/docs/doc-5501

• E-mail user interface executable back to the file of the sequence

  How can I move a message from the user interface of the executable back to a file of sequence?

  (TS_PropertySetValString) does not seem to work as I want it.  I get an error that the variable in the search string is not recognized.

  any help?

  Thank you

  You should always use PostUIMessageEx.

  As the collar of activeXDataParam ThisContext.  A single word.  ThisContext refers to the current SequenceContext, then you can always be assured that you are referring to the current context.

  Here is an example that shows how the ThisContext: http://zone.ni.com/devzone/cda/epd/p/id/5838

  Instead of him passing as parameter you are passing as a UIMessage.

  Hope this helps,

• To access the properties of a file of sequence of labview

  I want to produce a report based on data from file in sequence to relieve my documentation of software needs that must be in a specific format that. To do this, I want to write a labview program and enter the parameters of information of various teststand sequence and put them in a specific format.

  Most of the labview for testatnd tools require a context of sequence to exploit.  Is there a way to do this without having to open the entire teststand application and add a specific sequence?

  It seems to work for me.  Let me know if you have any questions.

• User Message message of Labview VI interface running on another thread

  I have a Labview GUI, which displays information on my oven.

  It's the thread that runs on the background it querys my oven, then I save variables stationglobals and then send a message to the user interface. It works very well.

  

  Now, I made an improved OVEN that not only monitor but also controls the oven. It is written in labview.

  on the above example, I use a statement for the user of Message interface:

  RunState.Thread.PostUIMessageEx (UIMsg_UserMessageBase + 1, 0, "",StationGlobals.ovenDatum, True)

  Where StationGolbals.ovenDatum is a container with the numbers and strings.

  Now on my Labview code

  

  I already have this wire in labview. So my question is... Can I just wire up my container in the ActiveXdataParameter ovenDatum or what I need to do some sort of conversion. ? I just do it?

  Problem solved after trying and you are looking for a solution...

  

• In the user interface, how can I property "Sequence Call Trace Setting" the stage of 'SequenceCall '?

  Hi all!

  I am writing a user interface. I want know step "SequenceCall" is tracingEnable or not. It is said that "use the Step.Module property to get a reference to a SequenceCallModule object. I can't well it. I can get a reference using "TS adapter API. But how he dose associated with the stage of 'SequenceCall '.

  Thank you!

  Hello

  You can do by using the node of given Variant to in LabVIEW.

  Please see the newsletter - get a different for TestStand objects Interface topic in the manual using Labview and LabWindows/CVI with TestStand for more information and an example.

  You can get a copy of this manual from this link - http://digital.ni.com/manuals.nsf/websearch/B8398AF8729D906F862577B4004FF10C if necessary.

  Concerning

  Anand jegou

  National Instruments

• to access the QML attached objects in C++ and best practices for the handling of the user interface in classes

  Hello

  I have in fact 2 queries

  (1) how can we access attachedobjects defined in QML in C++?

  (2) I'm loving development on Blackberry 10 C++ is one of my favorites. But I'm a bit lost when it comes to managing the user interface in classes. For example when we create the project through momentics we have a class called ApplicationUI. It manages all the (default) user interface commands, we in C++. as for example creating the document qml and setting as root user interface, etc. I am now working on an app that have NavigationPane as root, and then I continue to push pages (like the screens). But now the code for all pages is inside my ApplicationUI. What is the best practice to keep the UI for each page logic in a separte C++ class?

  I also develop for Android that a separate class for each activity, this code does not mingle for each activity. Please guide me how can I keep logic of user interface of each Page into a separate class of C++?

  regarding your second question:
  I think this is the simplest approach to keep all things in the UI in QML. You can easily put things into separate files.

  If you want to use c ++ to the user interface: can be done, too. just put it in separate classes and include those in your application class.

• How to lock access to the application user interface?

  Hello

  Our user interface application is configured to start automatically in the background when the BlackBerry is turned on.

  We have a configuration property (ShowUserInterface) in the application that will allow users to access the user interface by clicking on the application icon.

  Application continues to run in the background regardless of whether or not the ShowUserInterface configuration setting is 1 or 0.

  If the device is configured with ShowUserInterface = 1, the user interface does not appear to the user until the user clicks on the icon of the application. If the user closes or closes the application then it will continue to run in the background and maintain its condition.

  By clicking on the application icon again will open the application in its state of the screen.

  If the device is configured with ShowUserInterface = 0, then the user interface does not appear even when the driver click on the application icon.

  Please help how to achieve this?

  A code snippet

  public class MyApplication extends UiApplication
  {
      private Configuration config;
  
      private BackGroundThread _thread;
  
      public static boolean fromService = true;
  
      // Boot
      public static void main(String[] args) {
          if (args != null && args.length > 0 && args[0].equals("gui")) {
              // code to initialize the app by icon click
              fromService = false;
              MyApplication app = new MyApplication();
              app.enterEventDispatcher();
          } else {
              MyApplication app = new MyApplication();
              app.enterEventDispatcher();
          }
      }
  
      public MyApplication() {
          if (fromService) {
              _thread = new BackGroundThread(); // create a new separate thread
              _thread.start(); // start the thread
  
          } else {
              if (config.isShowUserInterface()) {
                  pushScreen(new LoginScreen());
              } else {
                  // what to do here?
              }
          }
      }
  }
  

  When the user clicks on the icon of the application and config.isShowUserInterface () = false in this case I'm not pushing any screen of the application. It is for me only IU lost Focus error.

  Any help will be appreciated.

  Thank you

  Look at acceptsForeground().  I think that you can simply return config.isShowUserInterface ().