Similar Questions

• LaserJet P1102: Stuck on new device is now connected

  Thank you for takeing your time to read this.  I have a problem installing my new LaserJet P1102, the instalation of driver's stuck to new device is connected now... As far as I can see it is a known problem, but cannot find a way to fix it.

  The printer is detected:
  
  

  

  What should I do?

  I have solved the problem, deleted the drivers in the Device Manager and reinstalled windows drivers.

• The progress of the installation is blocked on 'the new device is connected now' bar is just reload!

  The progress of the installation is blocked on 'the new device is connected now' bar is just reload! HP laserjet M1132 MFP

  Welcome @HELPMEPLSHSLOL,

  Thank you for your participation in the forums! I see that you are getting the error "new device is now connected" when you try to install the printer software. I'd love to help you.

  If you are using Windows and you're using a USB connection, try the steps in this document: HP Laserjet products - "Device setup has not completed" or the "Unknown device" Message appears in Windows during Installation of USB. If the printer will not be updated of the Manager of devices in the two Solution, make a right click and uninstall the print device. It may be listed as unknown device, USB or Laserjet M1132 print media. Disconnect, then reconnect the USB cable to see if it will continue the installation. If it is not that whatever it is listed for your printer, try another USB port directly on the computer or another USB cable.

  What operating system do you use? How to find the Windows Edition and the Version on your computer.

  How is the printer connected?

  Feel free to click on the 'accept as Solution' and the 'Thumbs Up' If this helped. Please let me know the results. Best regards

• I have a key to firefox sync. How can I synchronize a new device with it?

  I want to synchronize a new device, but all I have is a sync key and I can't find anywhere to enter the key of the synchronization. How can I do this?

  Firefox Sync (Aka recovery key) key has not been used since version Firefox 28. All you need is the email address used when you set up synchronization and the password for your account synchronization - assuming that you updated your account synchronization to a Firefox account after update beyond 28 of Firefox.

  And the former function of 'twinning' has disappeared, too.

• Drive external hard USB - cela used to work now I get an error message = "this device cannot start. (Code 10) "Any suggestions?

  Drive external hard USB - cela used to work now I get an error message = "this device cannot start. (Code 10) "Any suggestions?

  Hello

  I suggest to refer to this link and follow the steps in this link and check if that helps:

  http://support.Microsoft.com/kb/943104

  It will be useful.

• When you try to add a new device, on access to tools, Options, Sync tab, no manage an account or add a device link button. I can get codes displayed to appear on another device but cannot access a screen that I can enter the codes.

  When you go to the tab sync, I see nothing like the picture in the help pages that show a button manage an account and Add link device. I think I need to access the device link add to reach a screen that I can enter codes to set up the easy way sync. I have already overcome the problem of connection and enter my key synchronization but it's more effort and it seems to me that adding new devices does not work as described. I'm on a Win7 PC and a laptop Windows XP using Firefox 5 and using Firefox Home on an iPod Touch. I have not found a way to get into the 3 codes of four characters shown on my Win7PC on one of the other devices.

  Hello!

  If you have an account, but it seems that you are not logged in. Please, follow these steps:

  -Go to your tab sync in the Options window.
  -Press «Set up Firefox Sync»
  -Press half 'connect' down.
  -Select "I don't have the camera with me.
  -Now enter your contact information, including your sync key. And you're ready to go.
  -If you have lost your sync key, select the option below "I have lost my other device" and follow the instructions.

  I hope that this information resolves your issue.

• I use a new computer and now the ipod syncs not all songs because there is not enough space despite it showing 23 GB free.

  Have a new laptop. RELOADED iTunes library and allowed the computer. now, it not sync due insufficient free space. Necessary additional GB. It is projection 23 GB free.

  The following steps should solve the problems around the synchronization, assuming that all the content you want in your library.

  (If it isn't see recover your iTunes from your iPod or an iOS device)

  1. Backup device.
  2. Restoration as a new device.
  3. Restore the backup that you made earlier.

  NB. A feature introduced with iOS 9 called thinning or slicing app app allows each device to download just the code and resources required by this device, resulting in smaller downloads and a better use of the storage on the device. Therefore the device is no longer the universal version of the application that can be installed on any device to transfer applications is no longer supported. I hope that Apple will bring some changes to how it works, but in the meantime, you can download past purchases from iTunes or activate the automatic shopping app downloads to ensure that iTunes has always the apps you want on your device. As long as you make sure that all of the apps are present and updates in iTunes before you attempt a restore there should be no loss of data. I cannot confirm, but it seems a way to recent update all data are restored and apps that are not in the library are waiting to download from the iTunes Store over Wi - Fi, in a similar way to the restoration of the iCloud way works.

  TT2

• You can reset the original settings iTunes to see the iphone as a new device?

  I have problems syncing my phone. I had encrypted backup files, and now I can't synchronize without entering the password. However, I forgot the password and I can't customize the sync function. Is there a way to fix this problem, or do I need to reinstall the software? I have reinstalled ITunes, but encryption is still there. Is there a way to restore the original default settings iTunes, where it sees my phone as a new device?

  Having this same issue, just wondering if you have any where and how?

• Cannot read Photostory. Error message: "a device inthi system does not work.

  After building a slideshow Photo Story 3, I'm trying to play and get the error message: "a device attached to the system is not functioning:.»

  Unable to identify this device.

  Any ideas out there?

  Hi ld1925,

  • Did you the latest changes on the computer?

  Method 1

  I suggest that you install the updated drivers for the graphics card on the computer by visiting the manufacturer of the card or the computer manufacturer's website and check if it helps.

  If the update of drivers help not then uninstalled computer display card drivers, then reinstall the latest driver update.

  How to manage devices in Windows XP

  http://support.Microsoft.com/kb/283658

  Use Add/Remove remove programs and Device Manager to uninstall the drivers for the computer.

  How to change or remove a program in Windows XP

  http://support.Microsoft.com/kb/307895

  Method 2

  If the previous step fails, then it is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you put the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See the link below to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

  Method 3

  If the previous step fails, see if the problem continues in a new user account.

  How to create and configure user accounts in Windows XP

  http://support.Microsoft.com/kb/279783

• EMail address added to < < my device name > > < < my device name > > now using < < my mailadress (identical to the Apple ID) > > for FaceTime and IMessage.

  My iPod touch get now and then next alert message due to change on my iPhone.

  EMail address added to < < my device name > > < < my device name > > now using < < my mailadress (identical to the Apple ID) > > for FaceTime and iMessage.

  Why I get this message? iPhone is disabled due to my work offshore for two weeks, but the use of the iPod touch is allowed.

  What is my apple ID used on other devices with the same name as my iPhone?

  I would be happy if anyone has an explanation of why I feel this strange behavior.

  When you connect to FaceTime or Messages on another device, another peripheral other device using this same ID will get the message that has been signed to. Some iOS (and OSX) update log for other devices will get the message when that happens.

  You said "by reason of change on my iPhone"

  What has changed on the iPhone?

• Why I get this error message: error while trying to synchronize audio and midi?

  I just updated Logic Pro and all of a sudden my lexicon alpha interface does not work correctly.  I get this error message: error while trying to synchronize audio and midi. Check for conflicts between Logic Pro and the external device. Help

  Start by making sure that the project in logic settings are set correctly - I think that the lexicon only supports 44.1 or 48.

  If it is software used to Setup place the lexicon make sure you that the sampling frequency is set to the same logic.

  Sometimes that power and the lexicon solves the problem...

  If none of the help above - make sure you use a multi-out or comprehensive audio device (OS X)

  

• Creates a new partition and now bootcamp is not recognized

  Hi, I hope someone can help me.  I saw the thread here (repair Boot Camp after having created the new partition), but I had a suite of wire trouble and my setup may be different.

  I have an iMac with boot camp and created a new partiiton.  Now my windows boot camp does not start.  I see it in system preferences > startup in startup option disk, but when I have if I get the message 'no bootable disk '.

  If I restart and hold down the option, I see that my mac to start drive and not the windows partition

  Here is my system info:

  Boot camp is disk0s5

  

  

  

  I would appreciate it so no guidance in getting my new bootable Bootcamp.

  Please after the release of

  sudo dd if = / dev/rdisk0s5 account = 1 2 >/dev/null | hexdump - C

• I just installed a new router and now my desktop running Windows XP computer does not connect to the internet.

  Hello

  I just installed a new router and now my desktop running xp computer does not connect to the internet. I know that it is not the router because I plugged the cable into my laptop running 7 and it works fine. When I try to dhcp I get 169..., when I put manually the IP just get no access to the internet and can not ping to the router address. I tried to run the net work Assistant, emptied my dns, disabled all firewals, still nothing.
  Any suggestions?
  original title: connectivity Limeted

  The zero configuration utility works very well. But it is a desktop computer and on cable. All other wired and wireless PC in the office is working well, then it's definitely this PC. He came out of nowhere, I install a network printer on the PC but that's all.

  Your messages are a bit terse, but if I understand correctly

  • You have a router connected to the Internet and multiple computers connected to the router, some Ethernet cable and others by wireless.
  • All but one of these computers can reach successfully from the Internet via the router.
  • A computer that can't browse the Internet is connected to the router via an Ethernet cable.
  • You disconnected the cable between the router and the desktop problem and connected it to a Windows 7 laptop and the laptop connected to the Internet via the router.
  • You haven't seen any error message (except, perhaps, a message on "Limited or no connectivity").
  • You have installed Windows XP Service Pack 3 (or at least Service Pack 2)

  Assuming that all the foregoing is an accurate summary of the situation, I suggest that you do the following:

  Open a command prompt window (start > run > cmd > OK)
  Type the following lines and press ENTER after each line

  Netsh reset winsock catalog
  netsh int ip reset c:\resetlog.txt

  Close the command prompt window and restart the computer.

• Message: this device could better work with usb 2.0 when you connect the USB device.

  Original title: USB 2.0

  I get the message "this device could better work with usb 2.0", how do I change 1.0?

  I get the message "this device could better work with usb 2.0", how do I change 1.0?

  To answer your question directly: you replace with USB 1.0 (most likely USB 1.1) USB 2.0 by the purchase of new equipment.

  If you have a desktop computer, you can buy an internal with several Sockets USB 2.0 card.

  If you have a laptop, you can get a card with 2 ports USB PC Adapter 2.0

  Before you buy anything, however, if you have a desktop computer, it is possible that some (but not all) of your taken USB is 2.0.  Open the Device Manager (start > run > devmgmt.msc > OK), click on the + sign next to the category "Controllers of Bus USB" and watch the 'Host controllers' listed there.  If any host controller is 'enhanced' then you have at least one (and probably 2) USB 2.0 taken somewhere on the computer.

• New device

  I got a digital microscope USB of Optex for Christmas and I installed it.  When I connect the magnifer usb port and click the icon for stgart top, it comes up with the message "No Device detected, please connect your microscope directly to your USB port on the PC."  It has already been connected.  Please help me.

  Hi Coinguy,

  Welcome to the Microsoft Answers site!

  1. How you connect the device to your computer?
  2. Try a different USB port and check the status?
  3. You try to install a new driver for the device?
  4. You are able to install the drivers on another computer?

  After connecting the device, you must install the drivers that the computer detects the device.
  You may have received a CD that contains the necessary drivers for different operating systems. If you don't have the driver CD you may have to download the drivers from the manufacturer's Web site and install it on your computer.

  http://www.Microsoft.com/whdc/driver/install/default.mspx

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Hope this has been helpful.

  Kind regards
  Bindu S - Microsoft Support
  Visit our Microsoft answers feedback Forum and let us know what you think