Control word
Hi, looking at the table 7-3 and other pages of ciscopress Architectures VPN layer 2 (Pignataro, Bokotey, Luo, Chan), I see that the control word is always 0 for EoMPLS. When can be useful the word of command on EoMPLS?
(1) says that the control word is optional: Ethernet or Vlan over MPLS.
And can be reported or configured between two routers to support or not support.
(2) in Cisco for us flexibility in configuration, it was excluded and word order was upheld in State not supported. Currently we do not have need much outside the right VCID and label VPN to transmit traffic information received from Layer 2.
So the book can be read by people later in the future as well, made a cautious statement saying if the remote PE suports, as it may happen in the future if it is necessary to code some paparemeter that must be transmitted to the other side. Then, those who can be sent via the control word. Unlikely for now, but cannot be ruled out in the medium-term future.
HTH-Cheers,
Swaroop
Tags: Cisco Support
Similar Questions
-
I bought in the home edition of windows US, and now I've discovered there is no word?
My nephew bought for me Windows XP home edition to the United States and he sent me here, at the present time, I am here in Germany, and we can't buy your product in English. I had this program installed and found out that it does not contain the WORD, I'm old not a lot of money and not informed on these issues. I only know how to use words, someone installed for me this org.3.3 program, but I can't print a DIN A4 page, 2 pages. Please I need help.
Thanking you,
Sincerely,
Al.
You mean just Microsoft wordpad or Microsoft office Word?
for the processor, you will need to purchase Microsoft Office,
http://www.Microsoft.com/download/en/default.aspxIf wordpad, Word perhaps is not installed by default. (Check in the start menu-> all programs-> Accessories-> wordpad)
to install wordpad, go to the dashboard-> Add / Remove programs.
In this window, you can see the option "Add or remove windows components" on the left side of the window, click on that.
another window will open. If this control Word is available. If it is available, then check and install. (it may ask for the Windows CD).
alternative is, put your windows CD, then will come a Setup window automatically. (if it didn't, do it manually by the opening of the Conference on disarmament.
In this window, you can display options such as window installation, compatibility, add windows etc.
Click Add windows components. Select the word, and then install.org 3.3. is an alternative for microsoft office word and is not a microsoft product.
Thank you!!
-
OPC server in the shared variable
Hello
I am writing a program to read hundreds of OPC signal from a server. The server is a localserver in the PC, but this isn't a Labview server. My labview program reads the signal from the mutual FUND through the data in a Labview library. (Variable type = single process)
This way is functional but not optimal. I read in the help that I can use a published shared network variables. Is published this network can read the signal from my server through a network path without use of data? He will need a Labview Server?
This is an example for my opc address
OPC://localhost/hteControl_OPC_DA_Server/PLC_FI010_ValueLimit_SP
Thank you
fmpfmpf wrote:
Hello
I am writing a program to read hundreds of OPC signal from a server. The server is a localserver in the PC, but this isn't a Labview server. My labview program reads the signal from the mutual FUND through the data in a Labview library. (Variable type = single process)
This way is functional but not optimal. I read in the help that I can use a published shared network variables. Is published this network can read the signal from my server through a network path without use of data? He will need a Labview Server?
This is an example for my opc address
OPC://localhost/hteControl_OPC_DA_Server/PLC_FI010_ValueLimit_SP
Thank you
LV - DSC (data logging and control) words allows you to "bind" the NSV to an OPC server.
As long as the compliant OPC server operating system it should work and has been the case for me.
Ben
-
Hello
I'm trying to establish a connection to a VFD (Variable frequency drive) for academic research, for testing purposes. My implementation consists of:
---> LabVIEW (Master)
---> ABB ACS880 VFD (slave) with adapter from Fieldbus FENA-01
---> (ABB motor induction)
---> (Internal Combustion Engine)
First of all, I'm new to Modbus TCP protocol, but I went through all the white papers of NOR, I have read and followed all the instructions from the manual of the VFD and the fieldbus FENA-01 adapter manual. I'm also pretty new to LabVIEW, but I'm confident, I have the knowledge to create the necessary VI.
I created a simple VI who would be able to read some registers the VFD, which is attached below. The VFD is connected by Ethernet to network local ethernet and the Master PC is connected to the same network. When I run the VI, 56 error, which as I read from other messages of the forum is to not get answer within the given time.
I tried the things:
--> Check all cables are connected properly
--> Double check the manuals
--> Checking the FENA-01 in the chassis, which gives the indication of waiting for query modbus
--> Looking for a gateway IP address, but I did not find, so I expected, I don't have to add it to the VFD parameters
--> FENA-01 refreshing settings that always translates to "offline" status
-->, I also checked in Labview > tools > Options where you check TCP/IP and there no port 502 written but I do not change it cause I had to leave the laboratory at the time. The port number was something like 3363 (something like that again)
Issues related to the:
--> Do I need to specify a new device somewhere in LabVIEW or in the control panel?
--> What I need to create a separate VI to make the connection?
--> What 'send 1150 for operating loan' and ' send 1151 for operation "means the control word?
I would be very grateful if someone had information about this before the end of the week. I'm running tight on my period and I just can't stand this VFD with the limited power of the local command of monitoring mode.
Thanks in advance for any help.
Neo
Hello, the problem is solved, and this could be a solution to problems like these.
The IP address of the car was not on the same network as the Local Ethernet network connected to it. The IP address of the disk was 192.168.0.16 and the network was on 192.168.1.1. Once the IP address of the network changed to 192.168.0.1 communicated properly.
I also have ping after and showed the communication.
Thanks for the reply TST.
Peace,
Neo
-
ASR901: encapsulation xconnect vs xconnect default port mode
Hi all,
I have a doubt as to the potential difference between the xconnect with lack of encapsulation and the xconnect port mode, is the same thing? One is better than the other? which is the correct implementation and configuration of the port xconnect mode?
Here is my configuration:
ASR901-3 #sh run inter giga 0/5
Building configuration...
Current configuration: 236 bytes
!
interface GigabitEthernet0/5
no ip address
Loopback driver
auto negotiation
No keepalive
service instance 1 ethernet
lack of encapsulation
XConnect 192.168.201.4 123 mpls encapsulation
!
end
17:52:47.338 Jan 10: AToM LDP [192.168.201.4]: sending msg from the notif
17:52:47.338 Jan 10: AToM LDP [192.168.201.4]: sending notif msg type vc 5, cbit 1,.
17:52:47.338 Jan 10: AToM LDP [192.168.201.4]:, vc 123 ID.
17:52:47.338 Jan 10: AToM LDP [192.168.201.4]: group id 0, 29 vc label,.
17:52:47.338 Jan 10: AToM LDP [192.168.201.4]: status, 0 x 1 0 x 7/LDP/ADJ 0 0.
17:52:47.338 Jan 10: AToM LDP [192.168.201.4]: mtu 9216, handful of vc 0xF2000007
17:52:47.338 Jan 10: AToM LDP [192.168.201.4]: VCCV CC 0 x 2, HP 0 x 2
ASR901-3 #sh mpls l2 retail CR 123
Local interface: Gi0/5 place, line up, Ethernet protocol: 1
Destination address: 192.168.201.4, VC ID: 123, status of VC: upward
Output interface: Vl10, imposed label stack {20-25}
Preferred path: not configured
Default path: assets
Next section: 192.168.201.242
Create time: 00:05:20, last status change time: 00:00:32
Last label State FSM change duration: 00:04:02
Signaling protocol: LDP, peer 192.168.201.4:0 upwards
Target Hello: Id 192.168.201.6 (LDP)-> 192.168.201.4, LDP is in PLACE
Graceful restart: don't not configured and enabled not
Non-stop routing: don't not configured and enabled not
Support (local or remote) status TLV: enabled/supported
Watch LDP route: enabled
State/state machine of the label: Workbench, LruRru
Last local dataplane of State received: flawless
Last BFD dataplane received State: not sent
Last BFD counterpart received status monitor: no fault
Last received AC circuit State premises: no fault
Latest local circuit AC status sent: no fault
Last local PW I / f State received IARC: no fault
Last local status of LDP TLV sent: no fault
Last distance LDP TLV received State: no fault
Last LDP ADJ remote of State received: flawless
Labels MPLS VC: 29 local, remote 25
Group ID: 0 local, remote 0
MTU: 9216 local, remote 9216
Description of the remote interface:
Sequencing: persons with disabilities, send the disabled
Control word: on (configured: automatic detection)
Dataplane:
SSM segment/switch ID: 12300/8203 (used), with: 4
Statistics of the VC:
transit package totals: receive 0, send 0
the transit byte totals: receive 0, send 0
transit packet drops: receive 0, seq 0 error, send 0
ASR901-3 #.
the other side:
ASR901-1 #sh run inter giga 0/6
Building configuration...
Current configuration: 147 bytes
!
interface GigabitEthernet0/6
no ip address
Loopback driver
auto negotiation
No keepalive
XConnect 192.168.201.6 123 mpls encapsulation
end
18:49:01.934 Jan 11: AToM LDP [192.168.201.6]: sending msg from the notif
18:49:01.934 Jan 11: AToM LDP [192.168.201.6]: sending notif msg type vc 5, cbit 1,.
18:49:01.934 Jan 11: AToM LDP [192.168.201.6]:, vc 123 ID.
18:49:01.934 Jan 11: AToM LDP [192.168.201.6]: group id 0, label vc 25,.
18:49:01.934 Jan 11: AToM LDP [192.168.201.6]: status, 0 x 1 0 x 7/LDP/ADJ 0 0.
18:49:01.934 Jan 11: AToM LDP [192.168.201.6]: mtu 9216, handful of vc 0xAD000001
18:49:01.934 Jan 11: AToM LDP [192.168.201.6]: VCCV CC 0 x 2, HP 0 x 2
ASR901-1 #sh mpls l2 vc 123 det
Local interface: Gi0/6 upward, line protocol up, Ethernet towards the top
Destination address: 192.168.201.6, VC ID: 123, status of VC: upward
Output interface: Vl10, imposed label stack {18 29}
Preferred path: not configured
Default path: assets
Next section: 192.168.201.246
Create time: 00:19:47, last status change time: 00:16:16
Last label State FSM change duration: 00:19:46
Signaling protocol: LDP, peer 192.168.201.6:0 upwards
Target Hello: Id 192.168.201.4 (LDP)-> 192.168.201.6, LDP is in PLACE
Graceful restart: don't not configured and enabled not
Non-stop routing: don't not configured and enabled not
Support (local or remote) status TLV: enabled/supported
Watch LDP route: enabled
State/state machine of the label: Workbench, LruRru
Last local dataplane of State received: flawless
Last BFD dataplane received State: not sent
Last BFD counterpart received status monitor: no fault
Last received AC circuit State premises: no fault
Latest local circuit AC status sent: no fault
Last local PW I / f State received IARC: no fault
Last local status of LDP TLV sent: no fault
Last distance LDP TLV received State: no fault
Last LDP ADJ remote of State received: flawless
Labels MPLS VC: local 25, 29 remote
Group ID: 0 local, remote 0
MTU: 9216 local, remote 9216
Description of the remote interface:
Sequencing: persons with disabilities, send the disabled
Control word: on (configured: automatic detection)
Dataplane:
SSM segment/switch ID: 4097/4096 (used), with: 1
Statistics of the VC:
transit package totals: receive 0, send 0
the transit byte totals: receive 0, send 0
transit packet drops: receive 0, seq 0 error, send 0
# ASR901-1
In both cases, the loopback driver is set up because I do not have these ports connected to anything. But it's not important at this stage. The thing is that I have two ways to set up the same thing, but I don't know which is the right.
Thank you very much
Emiliano
Hello Emiliano,
In both cases, the encapsulation for xconnect is mpls only. the other encapsulation tht you defined as the service instance is to map an incoming tag to a service instance. If you receive an image without any tag it will be mapped to the instance of service 1.
Say assume that instead of 'default of encapsulation' we confiure "encapsulation dot1q 10" then all the frames coming with 10 tag will be mapped to this service instance.
Now a major difference between the two implementation is, one is the port-based EoMPLS is second evolutionary EoMPLS. In EoMPLS based on port, you can use this port only to L2 circuit service, while as part of the CVS, you can create several service instance and use them for different services.
Probably the biggest advantage of the VCA framework is the ability to support several services by physical port. This means that under a single physical port, you have the following mixed together:
-802. 1 q trunk
-802. 1 q tunnel
-Local connect
-Scalable EoMPLS (EoMPLS xconnect)
-Multipoint Bridging (L2 bypass)
-Multipoint Bridging (VPLS, focused on the SVI EoMPLS)
-L3 termination
Kind regards
Assani
-
Conditional display in the text box based on the calculated value
Hello
I have radio buttons that each have a numerical value. For example = 1 A = 2 C = 0. In the example below, the total is equal to 5.
The sum is displayed at the bottom of the document and is passed to another text box:
Instead of '5' displayed in the text box on the right, it should display a "Control" Word like this:
The displayed word is based on the totals through this range:
1-2 = 'absorbing '.
3-4 = 'practitioner '.
5 to 6 = "control".
The script I used to pass the value from the left to the right text box in the chart above is:
name of the field to text box;
var cTextBox = 'Cabinet Talent strategy knowledge - total';
get the value of the field with the name in cTextBox;
var sTextBox = this.getField ("cTextBox") .value;
Set the value of this field;
Event.Value = sTextBox;
That I need to add to this script to show one of the words, such as "control" above?
I am a complete novice to scripting. I found the above script online and somehow got it to work.
I thank very much for any help or pointers, you can provide.
Best regards
Sorry, there were some errors in the code that I provided above. Try this:
If (sTextBox > = 1 & sTextBox)<= 2)="">=>
Event.Value = "absorbing";
} ElseIf (sTextBox > = 3 & sTextBox)<= 4)="">=>
Event.Value = "practitioner";
} ElseIf (sTextBox > = 5 & sTextBox)<= 6)="">=>
Event.Value = "master";
} else {}
Event.Value = "";
}
If it still does not respond, you can send me the file at [email protected] and I'll check...
-
I set up a 'user' for my son and use parental controls. I want to him to have access to Word for Mac, and it appears in the list of applications I can check to allow use for. However, when we opened a session under his username, these applications do not seem to be anywhere. When you configure new users, applications such as Word for Mac or the available Pages on users? I can't find any information to help in this regard. I don't know if I'm missing something under user put up, or parental controls, or both. Any help would be greatly appreciated!
These requests should be made available, provided you installed then in the folder/applications, not in a private folder ~/Applications for a specific user.
-
form field check box control in word with report generation toolkit for Microsoft office
Hi all
Happy new year!
In the word template, I insert the checkbox field. It has a bookmark name "Check1."
Now, I try to checked or unchecked this field using the tool to generate report for Microsoft office and I couldn't. If someone now how to do? I'm using LabView 8.0
Thanks in advance,
Boris
Hi all
After I posted the question I found how to do it.
I use the macro feature to control the box.
Here's the diagram:
Thank you
Boris
-
Page control is displayed in Word format
Hello
I try to control the pages displayed in MS Word by jumping at them. I can jump to the previous and next, but I can't go to a page I want.
I know I'm doing something wrong with the invoke node (see below, the full code attached), but I don't know what because I don't know the syntax (if that's the right word, please correct me if I'm wrong).
I tried almost everything, but he doesn't like it!
The macro command is:
Selection.GoTo What: = wdGoToPage, which: = wdGoToNext, name: = "2".
Thank you
Andy
Hi Andy,.
Use the constant "wdGoToPage', as you do for other functions.
See the attached picture.
You can connect the new page as a string.
Mike
-
No response to the printers and faxes control or Word/Excel print command
No response to PRINT in Word or Excel or any other command print. No response to access Control Panel Printers and faxes.
A fix for this problem? Everything else works on Windows XP
If the printer driver is damaged, you must remove the old one first, either in step 4, described in an Article, or by using the procedures described in the article by Bruce Sanderson.
If you do not delete the old driver, Windows will use it even if you download and think that you install a new.
-
User account control: why I get this whenever I open word/excel?
original title: user account control
Just downloaded 2010 Home and Student and am running Windows 7. Whenever I try to open EXCEL or Word, I get user account control to allow "changes to the computer. I have another computer same configuration and is not the case?
Hi scdrenn,
Word and Excel on this computer are probly (when they open) being opened as Administor. Turn it off to:
- Find the location of the file of the program (Probly installed in Program Files > Microsoft Office)
- Right-click on Word or Excel first
- Then click Propities
- Click the Compatibillity
- In that list of checkboxes, Unckeck run this program as an administor.
- Apply then OK
If it isn't check, I'm ideas! Hope that you get runing like an Administor,
Will324
-
control panel messed up no icon in a few words
My Control Panel is done I have the icons but not write what I do please please help
My Control Panel is done I have the icons but not write what I do please please help
Maybe a system restore might do the trick?
http://www.Vistax64.com/tutorials/76905-System-Restore-how.htmlMake sure that you choose the date when Panel had words like your restore point.
t-4-2
-
HOW TO REPAIR WORD VIA THE CONTROL PANEL
WHEN I TRY TO OPEN MICROSOFT WORD, I GET A MESSAGE SAYING THAT IT CANNOT OPEN TO TRY AGAIN OR FIX IT USING THE CONTROL PANEL BUT I CAN'T FIND WHAT I NEED TO DO. Help, please!
Click on uninstall, and then click Repair
-
Como reparar produto (microsoft word startup) no message control
Microsoft word of estou tendo problemas com o. O programa não abre, e a resposta than e recebo "nao e possible open, novo tent or fix o programa no message control. EU gostaria Sabre, passo a passo como reparar o programa microsoft do word no message control.
Please select your language from the drop-down menu at the bottom of the page to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find the desired language, support for additional international sites options are by following the link below:
Por favor, selecione o idioma na lista suspensa acima para enviar sua question no language of his choice. O forum go e voce para Inglés only. SE você não o idioma desejado acima, suporte para may find other localidades Affairs pode ser encontrada through link abaixo:
-
Original title: can print test of control panel pages, but cannot print from applications (Word, WP) no error no message other than can not find printer.
Recently upgraded to SSD as boot drive. everything is working except cannot print from Word, WP or any application (Editor, etc.). Can print test pages to control panel on each installed printer, and do not appear. Try to print from Word he pauses and says "cannot find the printer." Tried reinstalling Word without solving the problem. I don't know that the problem is Windows 7 related, not printer hardware problem. Several times reinstalled printer that also does not resolve the issue. Any ideas? Anyone? Anyone?
Hi Doug,
I imagine the inconvenience that you are experiencing. I will certainly help the question of fixing.
To help you suggest several steps to solve the problem, I would appreciate if you could answer the following questions:1. What is the brand and model of the computer and the printer?
2. have you made any recent hardware or exchange of software on your computer before the show?
Please follow the methods and mark the question below:Method 1:
Step 1:Run the Microsoft Fix It from the link below.
Diagnose and automatically fix problems printing and printer:
http://support.Microsoft.com/mats/printing_problems/Step 2:
Follow the steps in the link below.Printer in Windows problems:
http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows
Method 2:
Follow the steps in the link below.Find and install printer drivers in Windows 7:
http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-driversMethod 3:Follow the steps in the link below.Why can I not print? :
http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-printIf the problem persists then I suggest to uninstall and reinstall the printer drivers.
I hope that the information above helps you.
Maybe you are looking for
-
How to force the iBooks of synchronization between devices?
Hello I am connected to iTunes on both my iPad and computer but no bought content (as PDF files) NEVER in sync. Also, I tried to sync the device using iTunes but still no joy. How to make this work? Any help would be appreciated. See you soon Ben
-
Laptops give up the Internet connection intermittently
I have a portable satellite, and my wife has a Tecra laptop. We connect through a PC to the internet via WIFI. Two notebooks remove the connection to the internet intermittently - to connect in the first place, we need to click on a few favorites in
-
Can't argue on facebook by Skype cuz draw online
I can't talk to my friends on facebook They onl online facebook, but online on Skype (facebook tab)(See attached file)How can I solve this problem?
-
Missed drivers Bootcamp 6.0 installation
I installed upgrading Windows 10 through Apple Software Update on my MacBook Pro 13 "(2015). Then found out that I couldn't open any of the Microsoft Office applications. Execution of programs and features fixed this issue. I then in the Apple softwa
-
Function non-contactable on printers MFP HP LaserJet 1536dnf of analysis after the upgrade to Windows 10. Here is the error message: I recycled the printer... inaccessible even I recycled the router and the printer... inaccessible even Worked fine be