Controller PXI-8108, causing the DMA failure

Similar Questions

• C70 - AC adapter / CC not enough load & causing the satellite failure

  Hello

  Didn't have any problems with the laptop again, except the power adapter.
  I noticed one thing, it requires just enough to keep the laptop, especially during physical or virtual games.

  But this isn't really a big problem, it's all just boring from time to time because I use it for school and I sometimes turn off just so that the battery can recharge a little bit. But you'll get used to that.

  But the second problem is worse elsewhere.
  Sometimes, when I connect my power adapter (even without the phone connected), it could cause a power outage and I have to change the circuit breaker. He was already held for the second time in four months, and I'm sure that there is a problem with the adapter.

  I'm not a native English speaker, so I couldn't quite understand.

  Data sheet:
  Type of laptop: Toshiba Satellite C70 - A - 17 c
  Article nr. : PSCEEE-00S006DU
  AC adapter model: PA5035U-1ACA
  Bought: May 26, 2014

  Kind regards
  Luuk

  Somehow the whole story seems strange to me.
  First the AC adapter should provide enough power to recharge even running some applications of high performance game.

  Second question also sounds very strange and I guess there must be some sort of dysfunction Ac adapter.
  I recommend you contact Toshiba service guys in your country in order to check the AC adapter.

  In case of hardware malfunction, the part needs to be replaced. Guarantee is valid?
  In this case, that the room should be replaced free of charge.

• Some of the Menus Adobe Premiere element cause DVD burning failures?

  Some of the Adobe Menus cause DVD burning failures?   What should have been a project of 10 minutes for a small 4 minute video took hours as burning DVDs stopped at 4% and then gave a message of "something has prevented completion in progress DVD burning".  I could finally solve it down for the Menu template, and when an audio clip looping has been added.  The Menu was built for an audio clip loop, but when I removed it the fine burned DVD.

  Since my last post, I checked that my drivers are up to date.   Driver updates were made to the display card Intel HD 4600 Graphics and Chipset Intel 8 series/C220 family SATA AHCI Controller.

  I created a new project and changed the flow of work to remove the check mark from selection to 'Add Menu markers automatically for me'.   When the menu has been selected and displayed, only the main Menu was to confirm that I didn't remove the Menu scenes.   At this point, I finished the remaining workflow and tried to burn on DVD using the stated parameters previously.   However, it had the same failed result.

  I went then to the path of Premiere Elements menu bar: Edit > Preferences > General

  The option "use hardware acceleration (works on Intel HD Graphics 2000 and higher)" has been selected.  I unchecked this option and clicked on the OK"" button.   I then tried to burn DVD with DVD NTSC_Widescreen_Dolby preset.

  Success!   The DVD was burned and confirmed to work in older DVD player (AVCHD burning earlier disk did not work in older DVD player, but worked in a new Blu - Ray player).

  It seems that the "use hardware acceleration" option preferred default was the problem in the prevention of burning DVDs.

  A.T. Romano thanks for your quick response and help to solve this problem.

• When Firefox crashes and restart is necessary, Firefox always try to open the same tabs that caused the failure before.

  I use tabbed browsing all the time. When I open a tab of a Web site that poses a problem, freezing Firefox (but not the computer), I find that I can delete the Firefox problem only by restarting the computer. I am so appalled to find that Firefox then tries to recreate the same set of tabs that caused the problem in the first place, causing Firefox freeze again. Usually I can get it out by closing Firefox and very long wait for Firefox to close completely so that it can be restarted again.

  This problem occurs in version 4.0 as well as in the latest version of 3 that I had. I remember that in some versions previous Firefox asks if you want to recreate your tabs or open in a new browser window. I always took the second option. This choice is no longer makes its appearance.

  Set the pref browser.sessionstore.max_resumed_crashes to 0 on the about: config to get page the on: sessionrestore page immediately with the first reboot after a failure has occurred or the Task Manager was used for the closing of Firefox.

  Which allows to deselect the tabs that you do not want to reopen, but will reopen the other tabs.
  
  See:

  • http://KB.mozillazine.org/Session_Restore#Restoring_a_session_after_a_crash
  • http://KB.mozillazine.org/browser.sessionstore.max_resumed_crashes

  To open the topic: config page, type Subject: config in the address bar (address) and press the 'Enter' key, as you type the url of a Web site to open a Web site.
  
  If you see a warning then you can confirm that you want to access this page.
  
  You can use the filter at the top bar of the on: page config to more easily spot a pref.

• PXI, switching boards causes the boot can´t pc

  Hello

  I pxi-1044 with some pxi cards (pxi-4065 / 6509 / 2529 / 8431 / 8432 / 2576 (3 borads))

  and the pxi-8310 controller.

  When the system has been configured for the first time, it works well.

  but 2 of the borads (pxi-8432 / pxi-2576) must slot interchange (due to problems of space with their own, conectors)

  When the system power, both led (on pxi chassis) and together (led controller), but windows xp does not start,

  Led CONTROL switch to and restart the computer. over and over again.

  I remove all the advice and check that all are recognized through MAX except the two planks of switching.

  Change to a different location (never used) and the look of system work ok, pxi-8232

  this Council is recognized.

  What is the correct procedure to exchange some tips when MAX has a previos configuration?

  I would use the slot machines that I have problems with, is it possible?

  Thank you

  Insteading of delete here or trying to remove, we can always Dispatcher threads.

  Suite here. 

• kb2596615 causes ade to failure, error was 459: object or class does not support the set of events

  A couple of my users started getting our application error messages ade grown after you apply this update. Everything is well after its withdrawal. First mistake was 459: object or class does not support the set of events. Basically, no event has worked. Why is this update break my application? It should be removed from the queue of the update.

  Okay, I've worked on it with Microsoft, and the actual cause turns out to be:

  MS12-060 security update affects the functionality of Access database
  http://support.Microsoft.com/kb/2748410

  This article updated fingers MS12-060, specifically KB 2687441, as the culprit.

  It turned out that ActiveX controls on the form (specifically the Microsoft Common Controls 6.0 Toolbar), caused the failure.

  The solution was simple: on a patched machine, open each form with an ActiveX control in design mode, compile and save it. It worked for me. Ignore the details of the solution that I wrote in the previous post!

  You may need to resave MSCOMCTL. OCX, as suggested in the article, to get your databases to work.

  -Ken

• NI PXI - 8108 RT with real-time compatibility 2009 and PXI-1050

  
  

  Hello

  The PXI-8108 should work just fine with the PXI-1050 chassis. The only requirement is a chassis PXI uses a PXI controller and a SMU chassis uses a controller SMU. Since the 8108 both 1050 use the PXI standard, they should work very well together.

  Eric

• RAID 1 on PERC H200 showing the two failure predicts hd

  I have a Poweredge R210 with Raid 1 on a PERC H200 controller.  I ran the task of consistency check on the disk virtual and got a bunch of error ID 2350 reading the newspaper of alerts:

  There was an error of irrecoverable during the rebuild disk media or recovery operation

  -they have been saved to disk 0 and disk 1. Is it possible to rebuild the mirror on that?  Both hard drives are showing "failure foretold" in OMSA.  From what I can tell, replace a hard drive at the same time does not work, as resynchronization will fail.

  Ashevis,

  You are currently able to boot on the table? If yes then we run a Dset on the server to check the log of raid controllers. It might actually be a punched tape of parity. That's when the bad blocks of failure provided are rebuilt on the remaining good disks. That is what can cause both be showing predicted failure. Now, it may be also that readers just hit the threshold at about the same time and scored them both. We will be able to say that, with the controller log.

  If it's a punched tape of parity, then you will need to recreate the table and the operating system and restore from a backup. No doubt.

  If it's just that they are marked and then he would have a chance of recovery by rebuilding each, but there is always a risk of failure pred transfer of bad blocks, during reconstruction, the new disk. What causes a puncture.

  So, in summary, that the best course of action would be to backup the data, recreate and do a restore.

• Tecra 550cdt enabling the DMA mode

  Hello, I have a 550Cdt Tecra using windows 98se, I would activate the DMA mode for my hard disk drive, if enable DMA, after windows restarts, it stops showing the windows startup logo. I have to stop the laptop with the power button. In this case, I hear a click from the hard drive.

  I use the standard disk controller driver 05/05/98 of microsoft and to replace the Toshiba IDE controller driver extended 05/06/98 allows only to enable DMA for the CD rom, but not the hard drive mode.

  I did a long search on other forums and there are other people have the same problem. I checked the pinouts, slick IDE connector (PCB FAL2H0 HDD Flex Cable conn. B36080141012) and the IDE HD no. 21, DMARQ PIN is not connected to the motherboard.

  This could be a design problem? Is there a software solution or a modification of the connector is possible?

  Hello Florian

  As far as I know that this unit is about 8 years old, comes with Windows 95. Each book is designed and preinstalled to operate well and stabile. Physical infrastructure and pre-installed software must work harmonic. As far as I know that all of the settings in the software and the OS are configured to work without any problems. So much about the design problem.

  Back to your question: as far as I know if you want to use the DMA (faster information transfer) chipset and OS must be taken in charge. I think that in your case the hardware phone don't support that. Please do not forget that the right chipset driver is installed. All that s.

  In my opinion, expect a little too much of this good old classic. ;)

• By clicking on the firefox icon causes the blue screen crash

  It started Friday, February 25, at mid-day. The only changes to the system this morning there were a plugin Adobe Flash player or Shockwave update, I'm not sure and an update on the Office of Scottrade Elite trading app. Two of these changes took place around 0900. The problems began around 1130, when the system, Windows 7 Home Premium had a blue screen crash. Therefore, I uninstalled each of the applications mentioned. I can't open Firefox to work on plugins, because whenever I click on the icon I get a crash blue screen with the words "Failure of Page in the nonpaged area" at the top. I also uninstalled and reinstalled the Firefox application with no clear beneficial effect. Scottrade trading app has been reinstalled and working well, causing no other probs.

  Hi all

  I have just recived an e-mail from mrcart and I think it is very likely that his problems were caused by "Iolo System Mechanic Pro":

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/Windows-7-crashes-with-blue-screen-when-running/3e72f5e2-0d59-4946-8050-401a397e2911

  "Windows 7 crashes with blue screen during the execution of IE8, 'page in the nonpaged area failure'...
  What this shows is that the ampse.sys driver is the cause of the crash.
  The ampse.sys is a driver for System Mechanic Pro.
  System Mechanic Pro has been known to cause problems in Windows 7...

  best regards / John Kirk.

• Satellite A30: PXE - E61 media test check the cable failure

  OK got this message on a cell phone of friends
  Others have played with him and made it worse, and now I received the laptop to try and fix.

  When you start to get

  PXE - E61 media test check the cable failure
  PXE - M0F outgoing PXC Rom

  If his tent to boot from the local network instead of the hard drive I have reset bios by default I disabled everything when I F12 boot to hard drive get the error message rΘation and one at a time, that nothing works even when I try to disable lan starts, he tries always to.

  When I try to install from disk backup it is hard disk not found, but in the bios the hard drive is located and can not boot from it.

  I tried with winxp pro disc to try not to get an OS on the laptop any partition to the OS but a blue screen with an error 0 x 00000050 CrashFree disk gives error 1170 if I remember correctly.

  I can't update the bios with new version because she needs windows, I can't stop the lan because there is no setting in the bios very minimul with about 4 useful settings in it.

  Is the hard drive turned or is this a bug in the bios that it detects drive hard, but does not assign a letter properly?

  If I try the recovery console in xp Setup there is no disk to read or write, if I maps the drive in recovery only the cd/dvd rom found no hard drive.

  Any help would be great thank you because I don't know what to do, I don't think that the hard drive is shot myself but maybe if I can get a laptop and try the hard drive what she will say if it is or not, but for now I'm stuck with no. had to go.

  I tried many things
  1. cdrom out and replaced plugs
  2. Jack hard drive out and replaced
  3 took Ram out and replaced
  4. start since the utility disk
  5. start from the winxp disk
  6. Windows XP recovery console no hard disk on c d e f g
  7 disc utility says no hard drive gives me a x: > promt error number 11030 invalid destination by car. Hard disk by bios HITACHI DK23FA-30-(PM)
  9 winxp error if I try to install 0x0000008e

  Post edited by: Shoa

  Post edited by: Shoa

  Hello Shoah

  You did what I would recommend.
  I remember what one of my friends has had a similar problem on an A200. But after the BIOS reset by default, he was able to install the OS from the recovery CD.

  The whole is very mysterious. It looks like a HARD disk failure, but the HARD drive is recognized in the BIOS. But have you checked the HARD disk in other laptop or computer?
  You can try to connect the HARD disk via the external USB HDD controller and could check if it s ok and could format.

  I recommend also to remove the CD/DVD drive and the HARD drive, then set the BIOS to default settings immediately (don't forget to save changes). Then try to power upward without the HARD disc and the drive.
  To my knowledge, you should get an error message.
  Then stop the laptop and put both the device in Notepad. Then go to BIOS and check if both devices are properly recognized.

  Finally, I must say that I don't know if my proposal will help m.
  If she won't help, you will need to contact an ASP in your country, because it really looks like a serious problem.

  Good luck

• Replace step Fail State causes the sequence fail LW/CVI custom Code generator

  Hello

  I have a Code CVI generator as part of the Toolbox ATML importer.  OR kindly gave me an example of how to change the Type of step as part of the custom Code Generator DLL and that works very well.

  However, if I try to change the step Fail value causes the sequence fail to VTRUE it seems do not set the value when the sequence is examined on a test bench.

  The code I use is:

  TS_StepChangeStepType (stepHandle, & errorInfo, typeDefinition);

  -where typeDefinition can be modified to change the type of step, it works and I can change the type of step if necessary.

  TS_StepSetStepFailCausesSequenceFail (stepHandle, & errorInfo, VTRUE);

  -who does not, the box is always set to VFALSE.

  Is there something that I am missing?

  Thank you very much

  Steve

  Steve-

  You must use the PropertyObject step to change the failure step Option. There should be a line of code the generator of custom Code that calls:

  Get the step as a PropertyObject in case it is necessary to change the properties of the General step
  tsErrChk (TS_StepAsPropertyObject (stepHandle, & errorInfo & stepObject));

  The stepObject is what you need to pass to the TS_StepSetStepFailCausesSequenceFail function as follows:

  Set the Option of failure of step-by-step

  tsErrChk (TS_StepSetStepFailCausesSequenceFail (stepObject & errorInfo, VTRUE));

  Please let us know if this happens to you to correct results.

  -Jeff

• SMU-4304 causing the ripple on the input signal?

  I have an SMU-1082 chassis that contains a high-6341 and a PXI-4304 module.  To check my code, I have connected the analog input (channel 0) of the 4304 to the digital output (PFI 12) of the 6341.  My program VI shows a ripple of Vpp 0.2 on the analog input that I'm not using a scope.

  The wiring is SMU-6341 [12 PFI, DGND]-> SCB - 68 a,--> TB-4304 [AI0 +, -]-> SMU-4304

  I have attached photos of the verses reach the graphical VI.  The scope is the AI0 + AI0-terminals and the TB-4304.

  Y at - it a supplement on the ground that I should use, or is - this normal for the-4304 to add the ripple?

  Thank you

  Ron

  Short answer, is that there is nothing wrong with what you see.

  You have connected a digital output signal low impedance to a digitizer analog high input impedance. Since a digital signal is essentially a square of variable in time wave and square wave have edges of transition that contain information of very high frequency, you will almost always see a form of "ripple" (see animation synthesis of fourier of a signal square from this Wikipedia page ). Thus, a digital output signal is more concerned with the synchronization and the upgrade to be a square wave perfect.

  In addition, you can see additional "ripple" because of differences between the SMU-4304 and the noculars that you have demonstrated. the noculars can be a combination of a bandwidth of upper entrance (which can come from various sources like low sampling frequency on the 4304 which would result in a higher frequency of information recorded by the noculars for smoother transitions to research) and, possibly, a lower input impedance (causing less, if any, the reflection of signal which would cause the ringing of the signal).

• PXI-8108 vs LabVIEW RT

  Hello

  I'm looking for a table of compatibility, which would give for me, each PXI - the processor list compatible LVRT output.

  Anyone know where to find?

  From now on, I want only whether PXI-8108 can runs LV - RT 2014, 2013 or 2012, but a complete table would be very interesting manage obsolescence.

  Thank you

  Synthesis

  From what I can tell, you should be fine with those.

• passed the test after the step failure

  Hello

  I have a stage with test of numerical limit.

  I checked in properties, under run Options, step failure causes the sequence

  But when I washed up on the market, the result of the test is passed.

  When I change the Actions Post - on is not going to the next step Goto cleanup

  then the result of the test is failed.

  I have two other stations where I limited digital test with the same properties, but here I don't have to go to cleanup for a failure result.

  I use TestStand 2013.

  Please help me, thanks

  / Magnus

  Magnus,

  Instead of setting RunState.SequenceFailed in your Expression after, try setting Step.Result.Status to this value instead. It worked on my machine.

  I hope that helps!