Could not save file!

Similar Questions

• just upgraded to Imac 27 "5K, installed the Software Photoshop cs4, then saving files get 'could not save file currently in use or is still open' how can I remedy?

  just upgraded to Imac 27 "5K, installed the Software Photoshop cs4, then saving files get 'could not save file currently in use or is still open' how can I remedy?

  Check this message: Re: "cannot save (file name) because the file is already in use or left pending."

• Error: Could not save 'file name' because the file name was invalid. (PS CS6 + WIN 7)

  I recently bought a new desktop in WIN 7, but also Adobe Creative Suite CS6.

  My first internal hard drive 2 TB is the second installed is from my old PC, 250 GB.

  I get this error when you try to save a file to a file using the Save"" command.

  The message is false, because the file name IS valid.

  This error is persistent.

  This error will not occur when you perform the same operation on my second internal hard drive.

  This error occurs on the files above about 1 MB in weight.

  What is happening is that the original file which I try to do the "Save" command gets corrupted and lost.

  If I do not use the command "Save as" to save my work under a different name, my work is lost.

  The same problem occurs with the CS6 PS 64-bit and 32-bit versions.

  I am very disappointed and annoyed with what is happening.

  Any idea what's going on here?

  Then Yes, sugarsync may have much to do with the error.

• Could not save file under Reduced Size!

  I can't save a ~ 2 MB as size using Acrobat Pro X 10.1.3. I spared smaller files in a reduced size. Why is this? I called Technical Support and left a message for a reminder to hopefully solve this problem quickly. I was reminded in two minutes about, I held for a while, and then I was disconnected without talking to anyone!

  Thank you.

  I thought I should finally mention that Acrobat X Pro just didn't shrink after selecting the size reduced. I still called Technical Support and found that I had to do an OCR of the document and which corrects the problem. Apparently some graphics or pictures caused a problem, I understand.

  Thank you.

• HP 4620: HP 4620 scans very well, but could not save the analysis in a file

  The scanner scans very well, but could not save the analysis in a file. Whenever I try to save, it crashes.

  Hey @motikama,

  Welcome to the Forums of HP Support!

  I see that you encounter some problems with the scanning of your Officejet 4620 e-all-in-one for your Windows 7 PC. I can help you with that.

  To start, make sure that the printer is plugged directly into a wall outlet, not a surge protector. Once done:

  1. Uninstall all software associated with the printer to your computer.
  2. Restart your PC.
  3. Download and install the latest drivers by clicking on this link.

  Please let me know the results after following the above. If you can scan, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• HP Photosmart Premium C410b: could not save the scanned images

  I use the HP Scan application and the error message: -.

  Could not save the scanned images

  appears when you try to save in a folder as a PDF or any other format.

  Ironically, if I'm going by sending to the printer and then save to PDF it works!

  I checked and I'm using 4.2.2 with El Capitan HP driver software

  Any thoughts?

  Hello

  The application from HP for your printer is not compatible with El Capitan, so the output files incorrectly recorded.

  In the Hewlett-Packard folder move HP Scan to the trash and empty it.

  Before you install and use the HP Easy Scan application below which should save the files correctly:

  https://iTunes.Apple.com/us/app/HP-easy-scan/id967004861?MT=12

  Kind regards

  Shlomi

• ODAC 12.1.0.2.1 x 64 install on Win2012 "could not load file or assembly '.

  I downloaded and installed ODA 12.1.0.2.1 (64-bit) on a 2012 R2 Windows Server, including using the OraProvCfg utility to save the 4 Oracle.DataAccess.dll odp.net and 4 Oracle.Web.dll asp.net in Windows GAC.  The application depends on this facility is v6.5 ConnectShip warehouse that uses IIS web pages for the management of the administration.  Loading the web interface I get the ODAC following error:

  Could not load file or assembly 'Oracle.DataAccess, Version = 4.112.1.2, Culture = neutral, PublicKeyToken = 89b483f429c47342' or one of its dependencies. The system cannot find the file specified.)

  I can confirm that the DataAccess assemblies both Web are present in c:\Windows\Microsoft.NET\assembly\GAC_64.

  Anyone would be able to direct me towards a resolution of this error?

  Concerning

  Hi Alex,

  Once again, thank you for your comments.  Finally I could muscle my way through installation.  For anyone else who might happen to run in this case, it's the right thing:

  OS: Windows 2012 R2 (64-bit)

  App: ConnectShip warehouse 6.5

  Requirement for Oracle DB: ODAC 11.2.0.2.1 (32 bit)<---This was="" necessary,="" not="">

  As well as the installation of the 32-bit files ODAC, I also ran the utility OraProvCfg to register for the Oracle.Web.dll of ASP.Net and odp.net Oracle.DataAccess.dlls

  Once that ODAC 32-bit install was in place the rest of the ConnectShip facility fell in place without the following errors.

  See you soon

• Lightroom could not save the catalog

  I get the following error when trying to save my catalog:

  Lightroom could not save the name of the catalog 'Catalogue Lightroom'.

  I use Lightroom CC 2015.5

  I have over 300 GB of free space on my drive.  I have more than 3 GB of photos.

  Backup follows these steps before the failure:

  Integrity checking,

  Copy of catalog

  Catalog optimization

  The Catalog backup compression

  
  

  Any ideas on what to do next?

  I had a chat with Adobe session live support.  She has tried everything that you guys recommended then asked me to delete a bunch of files on my C drive because it was pretty full.  She said that this drive should be at least 2 x the size of the free catalog.  Once I cleaned stuff backup succeeded.  Thank you all.

• Export error records 'diagnosis package cannot be recovered from VMware vCenter Converter Standalone. "Error: could not generate file diagnosis of VMware vCenter Converter Standalone server.

  Hey, gentlemen!

  Trying to export logs from VMware vCenter Converter Standalone v 5.5.2 and this error occurs.

  "The package of diagnosis cannot be recovered from VMware vCenter Converter Standalone. "Error: could not generate file diagnosis of VMware vCenter Converter Standalone server.

  Can he save data to the file journal, but only coverter_gui newspapers, nothing else.

  Google search returns no results at all.

  What could be?

  OK, it is resolved after you restart the converter Services.

• The numbers "could not open file for some reason any."

  Suddenly some of my documents of numbers prompt response "numbers" could not open file for some reason any ' "the document is unavailable. Other documents numbers remain accessible. My backup versions invites the same response when I try to open them. Is there a solution?

  Hello Fred,.

  Thanks for this info and choosing the communities Support from Apple. I know how important is able to open all your files in numbers is for you!

  If I understand correctly, you cannot open some files of numbers even from backups, but others continue to work. To limit this problem, I would suggest starting with the following steps:

  1. first of all, run disk utility and check for questions on your hard drive, as hard drive problems can lead to situations like yours.

  Disk utility (Yosemite): a disc repair

  2. then, you can test this in a new user, to refine, if it's a question broad system or specific to your username.

  How to test a question in another account on your Mac.

  See you soon!

• Failure of the Time machine backup could not save "My Passport"

  When I try to do a backup on my Passport using Time Machine, he used to work over the years, and now it is the message I get:

  Failure of the Time machine backup could not save "My Passport"

  
  

  Does anyone has an idea to help me with this problem?

  
  

  (Sorry for my English but I speak French in Switzerland...)
  

  Have you tried to run utilities disk to check/repair the external hard drive? Here is something you can try.  http://pondini.org/TM/A4.html

• Could not load file or assembly ' NationalInstruments.VisaNS, Version = 8.9.20.108

  I have an app VS c# that references the assembly OR world.  It worked fine in 32-bit Windows XP environment.  However, when I installed and ran the application in the Windows 7 64-bit environment.  The app was the following text:

  System.IO.FileNotFoundException: Could not load file or assembly 'NationalInstruments.VisaNS, Version = 8.9.20.108, Culture = neutral, PublicKeyToken = 4544464cdeaab541' or one of its dependencies. The system cannot find the specified file.
  "File name: ' NationalInstruments.VisaNS, Version = 8.9.20.108, Culture = neutral, PublicKeyToken = 4544464cdeaab541"

  Where can I find this assembly file version and why did not he ask you when I ran into the Windows XP 32-bit platform?  It's the same application binary.

  Thanks for your help!

  Another reason, you can get this error if you have your target, the value 'Any CPU' platform in the project properties. "Any CPU" setting causes the application runs in 32-bit on a 32-bit system and 64-bit on a 64 bit system mode. It would be a problem or a 64-bit system because you don't have the 64-bit installed assemblies and a 64-bit application cannot load a 32-bit assembly. You must change this setting to 'x 86' which will force to run in 32-bit mode on 32-bit and 64-bit systems.

• How can I fix error with package installed: "could not load file or assembly ' NationalInstruments.Daqmx.dll

  I'm fighting this problem for days (euphemism)...

  I used to work, but now isn't an installation package.  I tried to install and run the program on a couple of computers and the program hangs when loading the Dll NI.  I put everything ' x 86.

  The list of dependencies in VS2010 is illustrated in the attatched screenshot.

  The text of the mistake of trying to run the application on the target computer is lower in italics.

   

  Of course, I could use some help on this!  Thanks in advance.

  See the end of this message for details on the call
  just-in-time (JIT) debugging instead of this dialog box.

  The exception text *.
  System.IO.FileNotFoundException: Could not load file or assembly 'NationalInstruments.DAQmx.dll' or one of its dependencies. The specified module could not be found.
  File name: "NationalInstruments.DAQmx.dll."
  at IPClientTest.MTF_Supervisor.mainSstart13)
  at IPClientTest.MTF_Supervisor.mainStartByParts)
  at IPClientTest.MTF_Supervisor.lblSelfTest_Click (Object sender, EventArgs e)
  at System.Windows.Forms.Control.OnClick (EventArgs e)
  at System.Windows.Forms.Control.WmMouseUp (Message & m, MouseButtons, Int32 clicks button)
  at System.Windows.Forms.Control.WndProc (Message & m)
  at System.Windows.Forms.Label.WndProc (Message & m)
  at System.Windows.Forms.Control.ControlNativeWindow.OnMessage (Message & m)
  at System.Windows.Forms.Control.ControlNativeWindow.WndProc (Message & m)
  at System.Windows.Forms.NativeWindow.Callback (IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)

   

  Loading assemblies *.
  mscorlib
  Assembly version: 4.0.0.0
  Win32 Version: 4.0.30319.34011 built by: FX45W81RTMGDR
  Code: file:///C:/Windows/Microsoft.NET/Framework/v4.0.30319/mscorlib.dll
  ----------------------------------------
  MTF_Supervisor
  Assembly version: 1.0.3.3
  Win32 version: 1.0.3.03
  Code: file:///C:/mtfDebug/MTF_Supervisor.exe
  ----------------------------------------
  System.Windows.Forms
  Assembly version: 4.0.0.0
  Win32 Version: 4.0.30319.33440 built by: FX45W81RTMREL
  Code: file:///C:/windows/Microsoft.Net/assembly/GAC_MSIL/System.Windows.Forms/v4.0_4.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
  ----------------------------------------
  System.Drawing
  Assembly version: 4.0.0.0
  Win32 Version: 4.0.30319.33440 built by: FX45W81RTMREL
  Code: file:///C:/windows/Microsoft.Net/assembly/GAC_MSIL/System.Drawing/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
  ----------------------------------------
  System
  Assembly version: 4.0.0.0
  Win32 Version: 4.0.30319.34003 built by: FX45W81RTMGDR
  Code: file:///C:/windows/Microsoft.Net/assembly/GAC_MSIL/System/v4.0_4.0.0.0__b77a5c561934e089/System.dll
  ----------------------------------------
  MTF_ClassLib
  Assembly version: 1.0.1.0
  Win32 version: 1.0.1.0
  Code: file:///C:/mtfDebug/MTF_ClassLib.DLL
  ----------------------------------------
  NationalInstruments.UI.WindowsForms
  Assembly version: 13.0.40.242
  Win32 version: 13.0.40.242
  Code: file:///C:/mtfDebug/NationalInstruments.UI.WindowsForms.DLL
  ----------------------------------------
  NationalInstruments.UI
  Assembly version: 13.0.40.242
  Win32 version: 13.0.40.242
  Code: file:///C:/mtfDebug/NationalInstruments.UI.DLL
  ----------------------------------------
  NationalInstruments.Common
  Assembly version: 13.0.40.188
  Win32 version: 13.0.40.188
  Code: file:///C:/windows/Microsoft.Net/assembly/GAC_MSIL/NationalInstruments.Common/v4.0_13.0.40.188__dc6ad606294fc298/NationalInstruments.Common.dll
  ----------------------------------------
  System.Web
  Assembly version: 4.0.0.0
  Win32 Version: 4.0.30319.34009 built by: FX45W81RTMGDR
  Code: file:///C:/windows/Microsoft.Net/assembly/GAC_32/System.Web/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Web.dll
  ----------------------------------------
  System.Core
  Assembly version: 4.0.0.0
  Win32 Version: 4.0.30319.33440 built by: FX45W81RTMREL
  Code: file:///C:/windows/Microsoft.Net/assembly/GAC_MSIL/System.Core/v4.0_4.0.0.0__b77a5c561934e089/System.Core.dll
  ----------------------------------------
  NationalInstruments.Common.Native
  Assembly version: 13.0.40.188
  Win32 version: 13.0.40.188
  Code: file:///C:/windows/Microsoft.Net/assembly/GAC_32/NationalInstruments.Common.Native/v4.0_13.0.40.188__dc6ad606294fc298/NationalInstruments.Common.Native.dll
  ----------------------------------------
  System.Xml
  Assembly version: 4.0.0.0
  Win32 Version: 4.0.30319.33440 built by: FX45W81RTMREL
  Code: file:///C:/windows/Microsoft.Net/assembly/GAC_MSIL/System.Xml/v4.0_4.0.0.0__b77a5c561934e089/System.Xml.dll
  ----------------------------------------
  System.Design
  Assembly version: 4.0.0.0
  Win32 Version: 4.0.30319.33440 built by: FX45W81RTMREL
  Code: file:///C:/windows/Microsoft.Net/assembly/GAC_MSIL/System.Design/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Design.dll
  ----------------------------------------
  Accessibility
  Assembly version: 4.0.0.0
  Win32 Version: 4.0.30319.33440 built by: FX45W81RTMREL
  Code: file:///C:/windows/Microsoft.Net/assembly/GAC_MSIL/Accessibility/v4.0_4.0.0.0__b03f5f7f11d50a3a/Accessibility.dll
  ----------------------------------------

  Salvation Lorne.V.,.

  Exactly how you install OR DAQmx on the target computers?  Even if you include the DAQmx merge module in your version, you always need to install DAQmx on the target machine separately.

  You can also confirm that the DAQmx.dll is installed in the same directory on the development and deployment of the machines?  And you have the same version of DAQmx on both machines?

  Kind regards

• Could not load file or Assembly runtime being more recent than currently loaded run time

  I've recently upgraded to TestStand 2010 and Visual Studio 2010 TestStand 4.2.1 and Visual Studio 2008. I now get the following error in the analysis of the sequence for all calls to my .net dll.

  "Step"My_StepType"not loadable module. Could not load file or Assembly or one of its dependencies. This Assembly is built by a runtime newer than the runtime currently loaded and cannot be loaded. »

  I don't know how LONG it is. All of this worked previously. I tried to go back to the dll, but that makes no difference.

  Any ideas?

  Thank you.

  I found where this topic is discussed in detail a bit more.  It is in the TestStand reference manual that is installed with TS.  TS 2010 it's on page 5-12 and the section labeled using .NET Framework under section adapter .NET of Chapter 5 (Module adapters).

• Could not load file or assembly NationalInstruments.DAQmx

  I get an error 'Could not load file or assembly NationalInstruments.DAQmx' when I put my application on another computer.  The only difference between the two computers that I can say is that one that doesn't use the 64-bit Windows version and one who does has the 32-bit version.

  DAQmx exists on the computer and I can control the acquisition of data through the Explorer measurement & cutting automation.

  Any suggestions?

  Thank you

  Garth

  I solved the error by downloading the latest version of DAQmx on computers and recompiling code using the most recent version.