Could not start the Windows Firewall

Similar Questions

• Windows ICS Services stopped & could not start the windows firewall in windows xp professional sp2.

  I am facing a problem regarding the ICS Service & could not start windows in windows Xp service pack 2 firewall, whenever I have install windows Xp Sp2 and join the network, the ics services ceased and the windows firewall. While windows firewall service starts when I restart my computer. But after some time stopped again had services that I'm cold does not access the readers of part, could not access network resources.this problem occurs only on windows xp sp2, when I install windows 7, then all better.i work fetch on different forums, apply the settings but I'm not able to solve the problem on base all the time. Someone tell me the permanent solution of this problem, on a forum, I see this solution,sharedaccess.reg and settings.but I am still unable to find a permanent solution.

  Someone tell me the permanent solution of this problem?
  
  
  
  

  Hello

  Here are a few troubleshooting steps that you can try to solve this problem. See the following links.

  You cannot start the Windows Firewall service in Windows XP SP2

  http://support.Microsoft.com/kb/920074

  Registry WARNING: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, see this link:

  http://support.Microsoft.com/kb/322756

  Troubleshooting settings of Windows Firewall in Windows XP Service Pack 2 for advanced users

  http://support.Microsoft.com/kb/875357

  If you have additional problems, please reply to this post and we will be happy to help you further.

• There is more! ... Re: "could not start the Windows Firewall: error no. 5.

  Member of the community of Windows 'rap2pac' has provided a working solution for many of his colleagues in the Windows community. who has managed to "Start" the service of WIndows Firewall except for 'my computer '! * * * *

  My laptop FAS recently survived an attack of one of these "ransom of FBI virus". It took the comprehensive analyses of the, "AVG Free 2013"and "Security Essentials" of Microsoft to find and remove all four of the Trojans, who were in fact the active components of the "FBI virus".

  There was also the necessary research in the 'register', "Temporary files" and the "user files" to locate and delete all newly modified and/or suspicious looking for folders, files, permissions or registry keys.

  Unfortunately, after all signs of the virus seemed to be gone, I discovered that Windows Defender and Windows Firewall were the two people with reduced mobility. Windows Firewall wouldn't start and that's what brought me here... to find a solution.

  I read on and is quickly realized that I was not alone. There are many other victims without Windows Firewall. I came across the answer of "rap2pac", which contained a solution that received "rave." I followed his instructions and applied to my laptop. When I clicked on "Start", to start the Windows Firewall service, a window has popped up with this alert message:

  " ! Windows cannot start the Windows Firewall service on the Local computer.

  ERROR 1079: the account specified for this service is different from the account specified for other services running in the same process. »

  I don't understand what that means. I am at a loss and my fuistrations have overexceded their limited storage space... "me!"  ... ;)

  Please respond with any suggestions that you might have to help in the resolution of this problem.

  Thank you for your attention.

  Best regards, blsev

  Hello
  Follow these instructions to fix the Windows Firewall:
  Download and install Windows Repair:
  http://MajorGeeks.com/tweaking.com_-_Windows_Repair_d7141.html
  When the repair of Windows opens, click start repair , click Start. Uncheck all boxes except for the following:
  -Reset the registry permissions
  -Reset the permissions of files
  -WMI repair
  -Repair Windows Firewall
  Then click Start. Once it is finished, restart your computer. Let me know if this helps you.
  Brian

• Message error "Windows could not start the Windows Firewall on the Local computer.

  I was check the status of the Windows Firewall and I got a message saying "update your firewall settings" and "use recommended settings" option. However, when I click on this option, my cursor is occupied for a while, but nothing happens then.

  I tried from Windows Firewall in the list of Services, and I got this error: ' Windows has no start Windows Firewall on the Local computer. " For more information, see the system event log. If he is a non-Microsoft service, contact the service vendor and refer to service 13-specific error code. »

  I also tried to fix problems using Windows Fix - It, but these two problems were still attached. Help, please.

  Thank you.

  If you have a malware infection in not too distant past, this could be a relic.

  First, run Disk Cleanup to rid the system of temporary Internet files. These can seriously slow down a Malwarebytes scan.

  Then run Malwarebytes.

  http://www.Malwarebytes.org/

  Time of installation, make sure that you do not check the box to install the trial PRO version...

  How to use Malwarebytes

  http://www.bleepingcomputer.com/virus-removal/how-to-use-Malwarebytes-anti-malware-tutorial

  Follow-up to the ADW cleaner...

  http://www.bleepingcomputer.com/download/adwcleaner/

  Do NOT click on the GREEN download button because it will bring only sadness. Use the right BLUE button below.

  When you are satisfied that there is nothing wrong in the system, re-run Windows patches...

• Could not start the Windows Firewall service, missing dependency services

  Hello Dustin,.

  I suggest the steps after booting in safe mode and make sure you copy the entire command from "Windows Registry Editor Version 5.00".

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows/Start-computer-safe-mode#start-computer-safe-mode=Windows-7

  Please come back after you have tried the above suggestions.

  Hi, well I thank you that I was finally able to get my BFE run on my computer.  Now, I will try to get my firewall up.

  Thank you once again the copy and paste work.

• Could not start the Windows Vista firewall

  Hi all

  I can't start the Windows Firewall service in anyway.
  I can't open it via Control Panel, as it is said simply: "the Windows Firewall settings cannot poster because the asscioated service is not running. You want to start the Windows Firewall service? »
  I click "Yes", then he said: 'Windows cannot start the Windows Firewall service. There is no error code indicated.
  I tried running "wf.msc" using the Microsoft Management Console. When this window appears, he says: "there was an error opening the Windows Firewall with advanced snap-in security.; The Windows Firewall with Advanced Security snap could not load. Restart the Windows Firewall service on the computer that you are managing. "Error code: 0x6D9.
  As it seems, I can not start it this way or the other.
  I pressed Ctrl + Alt + Delete and click on the Services tab, then click services on the bottom, and this opens the Services window.
  In the new Services window, I try to start the service "Windows Firewall". I get a message saying: "Windows could not start the Windows Firewall service on the Local computer.; Error 1068: the dependency service or group could start. »
  Therefore, it does not. The service is set to automatic.
  I found another process called 'Base filtering engine', which I discovered is related to the use of the Windows Firewall service. Then, that I try to start this service, and he said: "Windows has no start the engine service of filtering based on Local computer." Error 0 x 80320009: an object with this GUID or LUID already exists. »
  Still, I can't find a way to fix the problem. In addition, the service is set to automatic.
  So if someone could help me, give me ideas or tell me how to solve the problem, it would be greatly appreciated. Thanks in advance.
  P. S. sometimes, when I type things in the command prompt, I get a message saying that "the requested operation requires a rise." What it means
  ?
  EDIT:
  The base filtering engine
  IKE and AuthIPsec Keying Modules

  Internet Connection Sharing (ICS)

  IPsec policy agent

  Routing and remote access

  Windows event collector

  Windows Firewall

  All of these services don't work, with each saying "Windows did not start the * service * service on Local computer.; Error 1068: The dependency service or group could start. ", with the exception of the Base Filtering Engine service.

  EDIT:

  I believe that the motor of filter of Bae is the root cause of the problem, because when I try to start it, it says "Windows cannot start the engine service of filtering based on Local computer. Error 0 x 80320009: an object with this GUID or LUID already exists. ", so that all the other programs on this service, said depedent" Windows did not start the * service * service on Local computer. " ; Error 1068: The dependency service or group could start. ».

  EDIT:

  Hello everyone, I solved the problem. The problem is a corrupted, file called "secdrv.sys. To resolve this problem, I had to first download the file "secdrv.sys' out of my operating system CD. To do this, you must create a partition and "mount" a file on CD, on the newly created partition. The file you have to climb is and is called: "*: \sources\install.wim. Extending .wim means a "file system Windows Image" and to see what files it contains, you will need to download what we call the "Windows Automated Installation Kit". Explicit instructions on the installation procedure and where to get this program, is here: "http://www.vistax64.com/tutorials/86959-access-vista-install-dvd-files.html". Once you have the file mounted, just search the area mounted for "secdrv.sys", then copy and paste it in "C:\Windows\System32\drivers" or that where the drivers from your system. After that, restart and the BFE service and all of its dependencies should work properly. Thanks for the good help like SpiritX.

  Hello everyone, I solved the problem. The problem is a corrupted, file called "secdrv.sys. To resolve this problem, I had to first download the file "secdrv.sys' out of my operating system CD. To do this, you must create a partition and "mount" a file on CD, on the newly created partition. The file you have to climb is and is called: "*: \sources\install.wim. Extending .wim means a "file system Windows Image" and to see what files it contains, you will need to download what we call the "Windows Automated Installation Kit". Explicit instructions on the installation procedure and where to get this program, is here: "http://www.vistax64.com/tutorials/86959-access-vista-install-dvd-files.html". Once you have the file mounted, just search the area mounted for "secdrv.sys", then copy and paste it in "C:\Windows\System32\drivers" or that where the drivers from your system. After that, restart and the BFE service and all of its dependencies should work properly. Thanks for the good help like SpiritX.

• A small flag appears on the bottom of my screen that says activate security service Windows, but when I try to turn on it says could not start the Windows security service

  Original title: HELPPPPP

  My computer a little flag in the background with a x... said red it turn security service windows, but when I try to turn it on... it said windows security service cannot be started :/

  Hey ChelseaHarris,

  Take a look at two responses in the thread below the link to see if they allow the Windows launch security service:
  Could not start the Windows Security Center service.

  If these steps do not help, try to run a full scan using the Scanner from Microsoft which can be downloaded using the link below:
  Microsoft safety scanner

  Hope that helps.

• Could not start the Windows Security Center service.

  Could not start the Windows Security Center service. Tried to go to Services, but this message. Help me please!

  the error code says...

  one or more ActiveX controls could not be displayed because that is:

  1. your current prohibiti of security settings on this page activex controls running or,

  2. you have blocked an editor of one of the controls.

  Hello

  ·        Since when are you facing this problem?

  ·        Remember to make changes to the system?

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  I suggest you follow the steps mentioned below.

  a. click on Start menu and type regedit.exe in the start search box and press ENTER.

  b. navigate to the following location. You must remove 1 (parasite) of additional area

  HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Internet Settings\Zones\
  with number Pseudo-graphique, you will see before the number of zone 0.

  c. check to see if the problem is resolved;

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows could not start the windows on the Local computer firewall

  Original title: I don't have the first response says.then the following error code came.
  Windows could not start the ICF on local Computer.For more information, review the system event Log.If this is a service not microsoft, the supplier of service relationship and refer to the specific service 5 error code

  Hello

  Thanks for posting the request in the Microsoft community forums.
  The problem description, I understand that you receive the error "Windows has no start the firewall windows on the Local computer. To resolve this problem, please answer the questions.

  1. what anti-virus software is installed on the computer?
  2. do you have a third party security/firewall on the computer?

  If Yes, then you may not be able to start Windows Firewall, since you have a 3rd group of firewall installed.

  Even if you can re-enable the Windows Firewall, you can not run two firewalls at the same time.

  Try the troubleshooting suggestions provided to start the Windows Firewall.

  Method 1:

  Run the fix it from the link to the problems of the Windows Firewall Service and check.

  Diagnose and automatically fix problems of Windows Firewall service

  http://support.Microsoft.com/mats/windows_firewall_diagnostic/en-us

  Method 2:
  You can check the service for the Service of Windows Firewall if it is started or not.

  a. Click Start.

  b. in the start search box, type Services.

  c. click right on - run as admin.

  Check if the below mentioned services has mentioned State and type start.

  Firewall Windows started Automatic\Manual.

  base filtering engine Automatic\Manual has begun.

  driver authorization Windows Firewall started Automatic\Manual.

  Also check the dependency services that are required for the execution of the Service Windows Firewall.

  Method 3:
  You can scan System File Checker to fix corrupted files.
  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7
  http://support.Microsoft.com/kb/929833

  Method 4:
  If the problem persists then, try the steps from the link.
  Some services do not start in Windows Vista and Windows 7

  http://support.Microsoft.com/kb/943996

  Registry warning: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/ )

  How to back up and restore the registry in Windows

  Hope the information is useful. If you need help with the Windows Firewall, feel free to post you question in the forum. We will be happy to help you.

• Could not start the windows 0 x 80070003 firewall

  Hello

  I have a problem with my windows 7. If I try to activate the control panel Windows Firewall, it gives me the error: "firewall Windows cannot change some of your settings. Error code 0 x 80070003 ". I tried many things, I have no malware or viruses. If I try to boot from "services.msc", the error I get is: "Windows does not have start the Windows Firewall service on the local computer." Error 3: the system does not have the specified path. »
  Thank you and hope you can help me
  Hello
  Follow these instructions to fix the Windows Firewall:
  Download and install Windows Repair:
  http://MajorGeeks.com/tweaking.com_-_Windows_Repair_d7141.html
  When the repair of Windows opens, click on the tab to start repairs, click Start. Uncheck all boxes except for the following:
  -Reset the registry permissions
  -Reset the permissions of files
  -WMI repair
  -Repair Windows Firewall
  Then click Start. Once it is finished, restart your computer. Let me know if this helps you.
  Brian

• Could not start vista windows firewall

  When you try to start the services program through windows firewall I get this error message: windows could not start the service on the local computer's windows firewall.
  Error 1068: the dependency service or group could start.  I need help...

  In addition to that maverick said... Follow the steps below...

  1. run "netsh winsock reset " starting from an elevated command prompt and reboot...

  2. go to the again elevated command prompt, and then run 'netsh firewall set opmode enable' in the command window... that should do the trick...
  Best regards, H.M. KOWSHAL a.k.a W@R10CK

• I can not start the Windows Firewall service in Windows XP SP3

  I discovered this problem when I installed a new Brother MFC-7860 DW in my network. Although the computer can 'see' the machine, I can't print to it. The error coming from the troubleshooter has informed me that the firewall might be the problem. Now I find that I couldn't open the firewall. I tried the solutions in previous discussions. It seems that Windows Firewall is not yet installed on my machine even if the icons are in the control panel. When I tried MS Fixit for the firewall, it gave me an error and sent me to a web page that does not seem to address the situation. Help, please.

  Now I find that I couldn't open the firewall. I tried the solutions in previous discussions. It seems that Windows Firewall is not yet installed on my machine even if the icons are in the control panel. When I tried MS Fixit for the firewall, it gave me an error and sent me to a web page that does not seem to address the situation. Help, please.

  (1) you have a third-party security software installed?
  This could be due to that... What are the analyses of different viruses that you already have... It may be a product of firewall or security of third parties that interfere the windows firewall, disable one by one your security scanners and try for windows firewall

  (2)if you do not have these installed firewall products, this could be due to malicious software or some other problem...

  If you have an antivirus up to date solution its definitions and do a full scan of the system...

  If you do not have an antivirus solution, or one does not work, use one of the recommended tools (use only one at a time)

  http://www.Microsoft.com/security/scanner/en-us/default.aspx
  And/or
  http://www.Malwarebytes.org/products/malwarebytes_pro/
  And/or
  http://www.simplysup.com/tremover/download.html (shareware)
  And/or
  http://www.McAfee.com/us/downloads/free-tools/Stinger.aspx
  And/or
  http://www.Kaspersky.com/free-virus-removal-tool

  If this also isn't that the problem may be that your firewall service is damaged...
  
  (3) open a command prompt run as administrator and type sfc/scannow

  (4) try to fix the firewall service
  Run the tool repair services by ESET
  http://KB.ESET.com/library/ESET/KB%20Team%20Only/Malware/ServicesRepair.exe

  
  And/or
  Download and add this firewall Windows registry entry - download.bleepingcomputer.com/win-services/7/MpsSvc.reg
  (If you find difficulties to add to the registry to refer this http://www.windowstechinfo.com/2013/07/solved-cannot-import-to-registry-not.html)

  And/or
  Open a command prompt using run as administrator
  and copy - paste these
  Rundll32 setupapi, InstallHinfSection Ndi-Steelhead 132 %windir%\inf\netrass.inf
  and press enter

  And/or
  Download this file and added to the registry by double clicking on it
  https://www.dropbox.com/s/ozezmcs3nktc2s0/windowsxp_firewall_fix.reg
  (5)guest orders (run as administrator), type Netsh firewall reset , and press "enter."

• "WindowsUpdate_80070641" "WindowsUpdate_dt000"_"WindowsUpdate_00000641" "WindowsUpdate_dt000" __Windows could not start the Windows Installer service on computer local error 216:0xd8

  I have a 64 bit Windows 7 PC and cannot install updates.  Here are two screenshots.

  One contains two error message that I get when trying to update

  "WindowsUpdate_80070641" "WindowsUpdate_dt000"
  "WindowsUpdate_00000641" "WindowsUpdate_dt000"

  The second erorr is what I get when you try to start the Windows Installer Service.

  Windows cannot start the Windows Installer service on computer local error 216:0xd8

  I follow several steps that are listed in the web pages of solving problems.  Tried to make own reboots, use the Microsoft Fix and it does not detect any problems.  I tried to install Windows Installer 4.5 and I get a message telling me that this update is not applicable to your computer

  Please notify

  See if this ad helps-

  http://social.answers.Microsoft.com/forums/en-us/vistawu/thread/213770d0-e94b-43B4-9ff6-99e6366b556b

  TaurArian [MVP] 2005-2011. The information has been provided * being * with no guarantee or warranty.

• Error - windows search on the local computer started and then stopped. Could not start the Windows Search service.

  Original title: windows search service does not start.

  When I try to start the service "windows search" I get the following error "windows search on local computer started and then stopped. Some services stop automatically if they have no work to do, for example, the services of newspapers and performance alerts' I tried manually and nothing, can someone help me please.
  It is a XP machine and yes I have windows search 4.0. I need help to get that windows search service has restarted.

  I no longer need it, I just backed up all my files and re - install windows XP.

• Could not start the windows DVD Creator

  "the adapter installed on this computer does not meet the minimum configuration required for creating windows dvd"

  Please see:

  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-video-card-system-requirements-for-Windows-DVD-Maker

  the minimum requirements for your videocard if you want to use Windows DVD Maker.

  If you are not sure, please post here the model of video card you have and someone will check for you.