Creation of VPN Tunnel / no connection is established

Hello

It's my first post on the Forums of Cisco, I hope you can help me with my problem. I'm trying to connecto to the network using a VPN from Site to Site connection using a router Cisco 1841 and Cisco PIX 515E. But for some reason, I couldn't connect the devices using a VPN configuration. Below I will list the device information of each:

PIX

Material: PIX-515E, 64 MB RAM, Pentium II 433 MHz processor
Flash E28F128J3 @ 0xfff00000, 16 MB
BIOS Flash AM29F400B @ 0xfffd8000, 32 KB

0: Ext: Ethernet0: the address is 0017.9514.5a3c, irq 10
1: Ext: Ethernet1: the address is 0017.9514.5a3d, irq 11
2: Ext: Ethernet2: the address is 000e.0caa.eaa0, irq 11

The devices allowed for this platform:
The maximum physical Interfaces: 3
VLAN maximum: 10
Internal hosts: unlimited
Failover: disabled
VPN - A: enabled
VPN-3DES-AES: disabled
Cut - through Proxy: enabled
Guardians: enabled
URL filtering: enabled
Security contexts: 0
GTP/GPRS: disabled
VPN peers: unlimited

This platform includes a restricted license (R).

Router

Cisco 1841 (revision 7.0) with 116736 14336 K/K bytes of memory.
Card processor ID FTX1137W00L
2 FastEthernet interfaces
1 Serial interface (sync/async)
1 module of virtual private network (VPN)
Configuration of DRAM is 64 bits wide with disabled parity.
191K bytes of NVRAM memory.
31360K bytes of ATA CompactFlash (read/write)

Here is the configuration of the router

'VPN_TO_PIX' 10-isakmp ipsec crypto map
By the peers = A.A.A.A
Expand the IP 110 access list
access-list 110 permit ip 192.168.2.0 0.0.0.255 10.10.0.0 0.0.0.255
Current counterpart: A.A.A.A
Life safety association: 4608000 Kbytes / 3600 seconds
PFS (Y/N): N
Transform sets = {}
PIX_CRYPTSET,
}
Interfaces using crypto card VPN_TO_PIX:
FastEthernet0/0

World IKE policy
Priority protection Suite 10
encryption algorithm: - Data Encryption STANDARD (56-bit keys).
hash algorithm: Secure Hash Standard
authentication method: pre-shared Key
Diffie-Hellman group: #1 (768 bits)
lifetime: 86400 seconds, no volume limit
Default protection suite
encryption algorithm: - Data Encryption STANDARD (56-bit keys).
hash algorithm: Secure Hash Standard
authentication method: Rivest-Shamir-Adleman Signature
Diffie-Hellman group: #1 (768 bits)
lifetime: 86400 seconds, no volume limit

crypto ISAKMP policy 10
preshared authentication
ISAKMP crypto key PIX_VPN_2010 address A.A.A.A

Crypto ipsec transform-set esp - esp-sha-hmac PIX_CRYPTSET
!
VPN_TO_PIX 10 ipsec-isakmp crypto map
defined by peer A.A.A.A
game of transformation-PIX_CRYPTSET
match address 110

Configuration of the PIX

NAT (inside) 8 access-list VPN_TUNNEL

VPN_TUNNEL to access extended list ip 10.10.0.0 allow 255.255.255.0 192.168.2.0 255.255.255.0

Crypto ipsec transform-set esp - esp-sha-hmac PIX_CRYPTSET
Crypto dynamic-map PIX_CRYPTSET_PIX 1 game of transformation-PIX_CRYPTSET
card crypto VPN_TUNNEL_MAP 20 set peer B.B.B.B
crypto VPN_TUNNEL_MAP 20 the transform-set PIX_CRYPTSET value card
card crypto VPN_TUNNEL_MAP 30-isakmp dynamic ipsec PIX_CRYPTSET_PIX
VPN_TUNNEL_MAP interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
the Encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
the Encryption
sha hash
Group 2

life 86400

After you run the status of devices and this is the results:

PIX

SH crypto ipsec stat

IPsec statistics
-----------------------
The active tunnels: 0
Previous tunnels: 0
Incoming traffic
Bytes: 0
Decompressed bytes: 0
Package: 0
Packet ignored: 0
Review of failures: 0
Authentications: 0
Authentication failures: 0
Decryptions: 0
Decryption failures: 0
Fragments of decapsules who need reassembly: 0
Outgoing
Bytes: 0
Uncompressed bytes: 0
Package: 0
Packet ignored: 0
Authentications: 0
Authentication failures: 0
Encryption: 0
Encryption failures: 0
Success of fragmentation: 0
Fragmentation before successses: 0
After fragmentation success stories: 0
Fragmentation failures: 0
Prior fragmentation failures: 0
Fragmentation failures after: 0
Fragments created: 0
PMTUs sent: 0
PMTUs rcvd: 0
Protocol of failures: 0
Missing chess SA: 0
System capacity: 0

SH crypto ipsec stat

IPsec statistics
-----------------------
The active tunnels: 0
Previous tunnels: 0
Incoming traffic
Bytes: 0
Decompressed bytes: 0
Package: 0
Packet ignored: 0
Review of failures: 0
Authentications: 0
Authentication failures: 0
Decryptions: 0
Decryption failures: 0
Fragments of decapsules who need reassembly: 0
Outgoing
Bytes: 0
Uncompressed bytes: 0
Package: 0
Packet ignored: 0
Authentications: 0
Authentication failures: 0
Encryption: 0
Encryption failures: 0
Success of fragmentation: 0
Fragmentation before successses: 0
After fragmentation success stories: 0
Fragmentation failures: 0
Prior fragmentation failures: 0
Fragmentation failures after: 0
Fragments created: 0
PMTUs sent: 0
PMTUs rcvd: 0
Protocol of failures: 0
Missing chess SA: 0
System capacity: 0

Router

Current state of the session crypto

Interface: FastEthernet0/0
The session state: down
Peer: Port A.A.A.A 500
FLOW IPSEC: allowed ip 192.168.2.0/255.255.255.0 10.10.0.0/255.255.255.0
Active sAs: 0, origin: card crypto

SH crypto ipsec his

Interface: FastEthernet0/0
Tag crypto map: VPN_TO_PIX, local addr A.A.A.A

protégé of the vrf: (none)
local ident (addr, mask, prot, port): (192.168.2.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (10.10.0.0/255.255.255.0/0/0)
current_peer 190.111.31.129 port 500
LICENCE, flags is {origin_is_acl},
#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
Errors #send 0, #recv 0 errors

local crypto endpt. : 190.120.2.82, remote Start crypto. : 190.111.31.129
Path mtu 1500, ip mtu 1500
current outbound SPI: 0x0 (0)

SAS of the esp on arrival:

the arrival ah sas:

SAS of the CFP on arrival:

outgoing esp sas:

outgoing ah sas:

outgoing CFP sas:

Any ideas, why is not made connection?, maybe a license restriction?

Help, please.

Best regards

ASA pre-shared key is not configured through the command "isakmp crypto key.

It would be by virtue of the following:

IPSec-attributes tunnel-Group B.B.B.B

pre-shared key

On the router, NAT exemption access list is incorrect. The following ACL:

access-list 111 deny ip 10.10.0.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 111 allow ip 10.10.0.0 0.0.0.255 any

Need to replace:

access-list 111 deny ip 192.168.2.0 0.0.0.255 10.10.0.0 0.0.0.255
access-list 111 permit ip 192.168.2.0 0.0.0.255 any

Then the 'ip nat inside' and 'ip nat outside' is the reverse. You have configured the following:

interface FastEthernet0/0
IP nat inside

interface FastEthernet0/1
NAT outside IP

It must be as follows:

interface FastEthernet0/0
NAT outside IP

interface FastEthernet0/1
IP nat inside

Tags: Cisco Security

Similar Questions

  • Questions of VPN tunnel

    People,

    You can help me understand how I can fix the following issues I have with a 1721 router (Version 12.3 (8) T5) and client VPN 4.6.01.x please.

    BTW, the server at 192.168.3.2 is a file, DNS, WINS server and proxy for the LAN environment. All the staff of the PC is required to use the proxy but visitors on the 192.168.2.0 network can access the internet directly.

    Back to my questions. I have the obligation to set up a VPN tunnel to connect to a PC that is running Terminal Server services / remote desktop on a PC to 192.168.1.9. When running the VPN software on the laptop I get a login prompt and everything seems fine. I ping the addresses of router and that works.

    But the three things I don't understand:

    1. I can't telnet with great success to the loopback address of the router, as well as other addresses 192.168.x.x. very well, but why is it possible that I can telnet to the 192.168.4.1 loopback address?

    2. I can't DRC to the server on 192.168.3.2. The server can (and) accepts connections on a subnet, I created the network of 192.168.6.x I put up as VLAN6 on SEA4 (the port of spare on the map of ether 4 ports). The only thing I did not in the configuration of the interface was the nat ip within the statement.

    3. I can't do a nslookup through the tunnel VPN (delays all the time) and neither can I http to the IIS server on the same 192.168.3.2 box. What I mean here is that other applications seem to work except telnet!)

    Then...:

    Why the telnet is so special? I thought that if I could telnet to the router, then I should be able to access the server. And before ask you, there is no firewall or whatever it is executed on the server by stopping this stupid connections. Hey, I'm the guy from router, not the jockey of server!

    I've managed to misinterpret the statement "corresponds to the address 105" in the cryptomap? The ACL would reflect the traffic flow both ways?

    I should have a statement of hash in the section of "crypto isakmp policy 5. The client indicates that the connection is OK then why should I need it?

    I appreciate your time to help. I was scratching my head a lot in the last two days.

    Timothy

    Your NAT config, it is what kills you here. You can telnet to the router interface, because then the NAT configuration does not take effect (because NAT doesn't happen for passing traffic THROUGH the router, FOR her). You must refuse the IPSec traffic to be NAT would have, otherwise, it does not match the encryption access list and is not encrypted on the way back.

    Your 100 access list is incorrect, remove it and add in the following:

    access-list 100 deny ip 192.168.0.0 0.0.255.255 192.168.5.0 0.0.0.255

    access-list 100 permit ip 192.168.0.0 0.0.255.255 everything

    That said NAT VPN traffic does 192.168.5.0, but NAT do it if he goes anywhere else (Internet).

    Also, you seem to have defined a map static encryption for your customer traffic, it is not used and may cause you problems with the list of access-105. Follow these steps to get rid of it and just use the dynamic encryption card:

    no card crypto clientmap 1

    You just need to have dynamic instance map (number 20) crypto left in your config file.

  • Use the client VPN tunnel to cross the LAN-to-LAN tunnel

    I have been troubleshooting an issue and cannot cross an obstacle. The ASA is running ASA running 1,0000 code 24. I am using a client VPN tunnel to connect to the ASA. The ASA has already a LAN-to-LAN tunnel, set up and operating and I need the VPN client to access the remote site over the LAN-to-LAN tunnel.

    The internal IP address of the local part is 192.168.0.0/24 and the IP address of the Remote LAN-to-LAN tunnel is 172.20.1.0/24. The clients are distributed 192.168.200.0/24 IPs. I have attached the relevant configuration for the SAA.

    When the VPN client on the network, I can access resources on the ASA network internal. On the internal network of the SAA, users can access resources through the LAN-to-LAN tunnel. Client VPN cannot access resources on the LAN-to-LAN tunnel. For the latter, there are no hits on the C-TEST access list.

    Thank you for your help.

    try adding...

    permit same-security-traffic intra-interface

    http://www.Cisco.com/en/us/products/ps6120/products_configuration_guide_chapter09186a00806370f2.html#wp1042114

  • ASA base S2S VPN, Tunnel establishes only when interesting traffic hits to end distance

    Dear all,

    I need your help to solve the problem mentioned below.

    VPN tunnel established between the unit two ASA.   A DEVICE and device B

    (1) if interesting traffic initiates a LAN device. traffic ACL hits. TUNEL is not coming

    (2) if interesting traffic initiates B LAN device. Tunnel will establish all the works of serivces

    (3) after the Tunnel device establishmnet B. We forced to tunnel down at both ends. Interesting again traffic initiates device a surpringly tunnel

    will go up.   After 2 or 3 days (after life expire 86400 seconds) initiated traffic of device A, tunnel will not esatblish.

    (it comes to rescue link: interesting won't be there all the time.)

    checked all parametrs, everthing seems fine. Here are the logs of attached but not more informative debugging on the balls. Please suggest.

    February 2, 2010 13:23:17: % ASA-7-713236: IP = 81.145.x.x, IKE_DECODE new SEND Message (msgid = 0) with payloads: HDR + HER (1), SELLER (13) + (0) NONE total length: 496

    February 2, 2010 13:23:18: % ASA-6-713219: IP = 81.x.x.x, KEY-ACQUIRE Queuing messages are treated when SA P1 is finished.

    February 2, 2010 13:23:18: % ASA-6-713219: IP = 81.x.x.x, KEY-ACQUIRE Queuing messages are treated when SA P1 is finished.

    February 2, 2010 13:23:23: % ASA-6-713219: IP = 81.x.x.x, KEY-ACQUIRE Queuing messages are treated when SA P1 is finished.

    February 2, 2010 13:23:25: % ASA-7-715065: IP = 81.x.x.x, history of mistake IKE MM Initiator WSF (struct & 0x1abb1e10) , : MM_DONE, EV_ERROR--> MM_WAIT_MSG2, EV_RETRY--> MM_WAIT_MSG2, EV_TIMEOUT--> MM_WAIT_MSG2 NullEvent--> MM_SND_MSG1, EV_SND_MSG--> MM_SND_MSG1, EV_START_TMR--> MM_SND_MSG1, EV_RESEND_MSG--> MM_WAIT_MSG2, EV_RETRY

    February 2, 2010 13:23:25: % ASA-7-713906: IP = 81.x.x.x, IKE SA MM:56f95c85 ending: flags 0 x 01000022, refcnt 0, tuncnt 0

    February 2, 2010 13:23:25: % ASA-7-713906: IP = 81.x.x.x, sending clear/delete with the message of reason

    February 2, 2010 13:23:25: % ASA-3-713902: IP = 81.x.x.x, counterpart of drop table counterpart, didn't match!

    February 2, 2010 13:23:25: % ASA-4-713903: IP = 81.x.x.x, error: cannot delete PeerTblEntry

    Hi, I have a similar problem a long time ago. You can choose which set up the tunnel in your crypto card:

    card crypto bidirectional IPsec_map 1 set-type of connection

    I hope that it might help to solve your problem. Kind regards.

  • Connectivity on the VPN tunnel problem.

    Hello

    I have a site to tunnel between the PIX506 and Cisco VPN 3000 Concentrator. I'll be spending it again ASA5510, so the tunnel will be established between the ASA and PIX. After inistial tests, I found only one box of remote network (time clock lol) is down by connectivity while tunnel between Pix and ASA (works fine with the hub). All traffic is allowed through the VPN tunnel built on SAA is? I understand it should be as long as the tunnel is running, correct? (Note: the remote clock uses ports TCP 8888 and 8889 to communicate with the server)

    Thank you

    If there is no filter, again all traffic should be allowed.

    You need not choose L2TP connection is pure IPsec.

    If you wish, you can post your configurations to check them out (you can remove sensitive information)

    Federico.

  • VPN tunnel via PPPoE connection

    The remote site uses a PPPoE DSL connection on a wic etihernet. We have the work of setting up PPPoE, but we are unable to establish the VPN tunnel. When the tunnel is activated, since the PIX debugging logs show the following:

    PEER_REAPER_TIMERIPSEC (ipsec_prepare_encap_request): fragmentation, IP packet<>

    0 > greater than the effective mtu 1444

    IPSec (ipsec_prepare_encap_request): fragmentation, IP <1500>packet greater than e

    effective MTU 1444

    IPSec (ipsec_prepare_encap_request): fragmentation, IP <1500>packet greater than e

    effective MTU 1444

    On the router when the encryption card is linked to the Dialer, debug information indicates the following:

    Sep 15 12:17:31.111: IPSEC (adjust_mtu): setting ip mtu of 1500 to 1444.

    local (identity) = *. *. *. *, distance = *. *. *. *,

    local_proxy = 192.168.50.0/255.255.255.0/0/0 (type = 4),

    remote_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4)

    Sep 15 12:17:31.115: IPSEC (adjust_mtu): setting mtu of 1500 path to 1444.

    local (identity) = *. *. *. *, distance = *. *. *. *,

    local_proxy = 192.168.50.0/255.255.255.0/0/0 (type = 4),

    remote_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4)

    Sep 15 12:17:31.115: IPSEC (adjust_mtu): setting ip mtu of 1500 to 1444.

    local (identity) = *. *. *. *, distance = *. *. *. *,

    local_proxy = 192.168.50.0/255.255.255.0/0/0 (type = 4),

    remote_proxy = 192.168.0.0/255.255.240.0/0/0 (type = 4)

    Sep 15 12:18:16.984: ISAKMP (0:0): no BID in demand

    Sep 15 12:18:16.988: ISAKMP (0:0): profile of THE request is (NULL)

    Sep 15 12:18:16.988: ISAKMP: 0 local port, remote port 0

    Sep 15 12:18:16.988: ISAKMP: set new node 0 to QM_IDLE

    If I run the following command on the router, test crypto isakmp. * *. *. * *. *. *. * ESP. I get the following information from the journal of debugging on the router. In the journal of Pix I start reporting the fragmentation, IP <1500>packet greater than the effective mtu 1444.

    Sep 15 12:18:16.988: ISAKMP: insert his with his 82121DD4 = success

    Sep 15 12:18:16.988: ISAKMP (0:1): cannot start aggressive mode, try main MB

    FEL

    Sep 15 12:18:16.988: ISAKMP: looking for a key for *. *. *. * in default: success

    Sep 15 12:18:16.988: ISAKMP (0:1): found peer pre-shared key matching *. *. *. *

    .62

    Sep 15 12:18:16.992: ISAKMP (0:1): built the seller-07 ID NAT - t

    Sep 15 12:18:16.992: ISAKMP (0:1): built of NAT - T of the seller-03 ID

    Sep 15 12:18:16.992: ISAKMP (0:1): built the seller-02 ID NAT - t

    Sep 15 12:18:16.992: ISAKMP (0:1): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM

    Sep 15 12:18:16.992: ISAKMP (0:1): former State = new State IKE_READY = IKE_I_MM1

    Sep 15 12:18:16.992: ISAKMP (0:1): early changes of Main Mode

    Sep 15 12:18:16.992: ISAKMP (0:1): package is sent to *. *. *. * my_port 0 wee

    r_port 0 (I) MM_NO_STATE

    Sep 15 12:18:20.440: ISAKMP: ke received message (1/1)

    Sep 15 12:18:20.440: ISAKMP: set new node 0 to QM_IDLE

    Sep 15 12:18:20.444: ISAKMP (0:1): SA is still budding. Attached is the new ipsec applicant

    She St. (local *. *. *. * distance *. *. *. *)

    Sep 15 12:18:26.996: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE...

    Sep 15 12:18:26.996: ISAKMP (0:1): will increment the error counter on his: broadcast

    Phase 1

    I tried setting the IP MTU size to 1492 and 1500 on the interface of the router Dialer but I still get the same case. You have any ideas or places to look. We are able to establish a VPN tunnel from this location with a Linksys VPN router or router Drakor. This same router also works when you are using a DSL connection, requiring no PPPoE.

    Thank you

    JUan

    Remove this line on the router:

    IP nat inside source list Dialer1 160 interface overload

    because this would cause the NAT router all encrypted packets which you don't want. On the PIX, you must change this:

    NAT (inside) 0-list of access splittunnel

    to reference the ACL sheep or add the 192.168.50.0 subnet in the ACL splittunnel.

    On the PIX, enter in the following (I know they are there already):

    Outside 1500 MTU

    Within 1500 MTU

    MTU 1500 dmz

    then save the config and rebooting, it must get rid of the MTU messages.

  • VPN connected, stream out of VPN tunnel

    I mean that we have in place of the VPN Sites manage to sites with 2 RV042 router but it seams not as I wanted. Are you sure that each transfer of data through Router 2 will go into the VPN tunnel or it shuts down the VPN tunnel. I checked the routing table and saw that:

    Sources mask Gateway Interface

    2 1 or wan wan IP 255.255.255.0 ipsec0 private

    By default 0.0.0.0 (ip wan 1 or 2) wan1 or wan2

    .........

    So what you think what sense data will pass through the line, it will go through the ipsec section or through wan1 or wan2. Ofcouse each data will pass through wan1 or wan2, but it can go inside the ipsec tunnel or ipsec outside tunnel. If she goes inside the ipsec tunnel, everything is ok, but if this isn't the case, transfer of unsecured data. I'm trying to access some website is not in private ip and it was outside ipsec tunnel go, I can capture and now that you have access.

    Why with linksys have 2 work as draytek product even photos follow:

    Can someone help me to answer this question, thank you for your attention

    1. it depends on what the tunnels of your business allows. As I've written before, there are other protocols that allows you to route traffic through the VPN tunnel. Only IPSec cannot do this. For example, if your company uses GRE over IPSec then they can route traffic through their tunnels. Your RV does not support this.

    2. If it's really plain IPSec then you cannot configure several subnets. You can try to implement the security group remote as a subnet more grand, such as 10.0.0.0/8. Of course the groups must match on both sides.

    3. If you want to route all traffic through the tunnel, and then try to set the local/remote security to 0.0.0.0/0.0.0.0 group. Maybe it works.

    The configuration of IPSec in the RV042 does not allow extremely complex configurations. It's mainly to connect two subnets between them.

  • Once the VPN connection is established, cannot ping or you connect other IP devices

    Try to get a RV016 installed and work so that people can work from home.  You will need to charge customers remote both WIN XP and MAC OS X.

    Have the configured router and works fine with the VPN Linksys client for WIN XP users.  Can connect, ping, mount the shared disks, print to printers to intellectual property, etc.

    Can connect to the router fine with two VPN clients third 3 for Mac: VPN Tracker and IPSecuritas.  However, once the connection is established, cannot ping the VPN LinkSYS router or any other IP address on the LAN Office.  Turn the firewall on or off makes no difference.

    Is there documentation anywhere that describes how the LinksysVPN for Windows Client communicates so these can be replicated in 3rd VPN clients from third parties for the Mac in OS X?

    The connection with IPSecuritas and VPN Tracker is performed using a shared key and a domain name.  It is not a conflict of IP address network between the client and the VPN 192.168.0.0/24 network.

    VPN Tracker and IPSecuritas are able to connect to the routers CISCO easy VPN with no poblem.

    Any ideas on how to get the RV016 to work for non-Windows users?

    We found and fixed the problem, so using VPN Tracker or current IPSecuritas on OS X people have access to the LAN via the RV016 machines. The "remote networks" in the screen BASE in VPN Tracker has been set on the entire subnet: 192.168.0.0/255.255.255.0 the in the RV016 has been set to the IP of 192.168.0.1 to 192.168.0.254 range. Even if the addresses are essentially the same, without specifying the full subnet in the RV016 has allowed the connection to do but prevented the VPN client machine to connect because the RV016 would pass all traffic to the Remote LAN. Change the setting of 'local group' in RV016 settings in the screen "VPN/summary/GroupVPN', 'Local Group Zone' for the subnet 192.168.0.0/24 full solved the problem.

  • Cannot complete the tunnel ' phase 2 ', by establishing a site to site VPN.

    I am trying to establish a VPN tunnel from site to site between a Cisco 1921 and an ASA.

    I am debugging using:

    Debug crypto ISAKMP

    Debug crypto ipsec

    No debug message is coming on the 1921.

    The following debug message returns constantly to the ASA:

    15 jan 16:42:55 [IKEv1]: Group = 184.1.126.140, IP = 184.1.126.140, construct_ ipsec_delete(): No. SPI to identify the Phase 2 SA!

    ASA config: http://pastebin.com/raw.php?i=wgTxe3gF

    1921 config: http://pastebin.com/raw.php?i=TEihijEF

    Why won't the two establish a VPN tunnel?

    It's very strange that ASA appears the tunnel, but the router does not work. It seems that the router is waiting for authentication.

    You can add-

    crypto isakmp key address 184.1.96.42 no-xauth

    You can debug isakmp and ipsec on the router and display it?

  • ASA 5505 and ASA 5510 Site to Site VPN Tunnel cannot be established

    Hi all experts

    We are now plan to form an IPSec VPN tunnel from site to site between ASA 5505 (ASA Version 8.4) and ASA 5510 (ASA Version 8.0) but failed, would you please show me how to establish? A reference guide?

    I got error syslog 713902 and 713903, how to fix?

    I got the following, when I type "sh crypto isakmp his."

    Type: user role: initiator

    Generate a new key: no State: MM_WAIT_MSG2

    Hugo

    Hello

    This State is reached when the policies of the phase 1 do not correspond to the two ends.

    Please confirm that you have the same settings of phase 1 on both sides with the following commands:

    See the isakmp crypto race

    See the race ikev1 crypto

    Also make sure that port UDP 500 and 4500 are open for communication between your device and the remote peer.

    Finally, make sure you have a route suitable for the remote VPN endpoint device.

    Hope that helps.

    Kind regards

    Dinesh Moudgil

  • Remote access VPN client to connect but cannot ping inside the host, after that split tunnel is activated (config-joint)

    Hello

    I don't know what could be held, vpn users can ping to the outside and inside of the Cisco ASA interface but can not connect to servers or servers within the LAN ping.

    is hell config please kindly and I would like to know what might happen.

    hostname horse

    domain evergreen.com

    activate 2KFQnbNIdI.2KYOU encrypted password

    2KFQnbNIdI.2KYOU encrypted passwd

    names of

    ins-guard

    !

    interface GigabitEthernet0/0

    LAN description

    nameif inside

    security-level 100

    192.168.200.1 IP address 255.255.255.0

    !

    interface GigabitEthernet0/1

    Description CONNECTION_TO_FREEMAN

    nameif outside

    security-level 0

    IP 196.1.1.1 255.255.255.248

    !

    interface GigabitEthernet0/2

    Description CONNECTION_TO_TIGHTMAN

    nameif backup

    security-level 0

    IP 197.1.1.1 255.255.255.248

    !

    interface GigabitEthernet0/3

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Management0/0

    Shutdown

    No nameif

    no level of security

    no ip address

    management only

    !

    boot system Disk0: / asa844-1 - k8.bin

    boot system Disk0: / asa707 - k8.bin

    passive FTP mode

    clock timezone WAT 1

    DNS server-group DefaultDNS

    domain green.com

    network of the NETWORK_OBJ_192.168.2.0_25 object

    Subnet 192.168.2.0 255.255.255.128

    network of the NETWORK_OBJ_192.168.202.0_24 object

    192.168.202.0 subnet 255.255.255.0

    network obj_any object

    subnet 0.0.0.0 0.0.0.0

    the DM_INLINE_NETWORK_1 object-group network

    object-network 192.168.200.0 255.255.255.0

    object-network 192.168.202.0 255.255.255.0

    the DM_INLINE_NETWORK_2 object-group network

    object-network 192.168.200.0 255.255.255.0

    object-network 192.168.202.0 255.255.255.0

    access-list extended INSIDE_OUT allow ip 192.168.202.0 255.255.255.0 any

    access-list extended INSIDE_OUT allow ip 192.168.200.0 255.255.255.0 any

    Access extensive list permits all ip a OUTSIDE_IN

    gbnlvpntunnel_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

    standard access list gbnlvpntunnel_splitTunnelAcl allow 192.168.202.0 255.255.255.0

    gbnlvpntunnell_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

    standard access list gbnlvpntunnell_splitTunnelAcl allow 192.168.202.0 255.255.255.0

    pager lines 24

    Enable logging

    asdm of logging of information

    Within 1500 MTU

    Outside 1500 MTU

    backup of MTU 1500

    mask of local pool VPNPOOL 192.168.2.0 - 192.168.2.100 IP 255.255.255.0

    no failover

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm-645 - 206.bin

    don't allow no asdm history

    ARP timeout 14400

    NAT (inside, outside) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

    NAT (inside, backup) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

    NAT (inside, outside) static source DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

    NAT (inside, backup) static source DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

    !

    network obj_any object

    dynamic NAT interface (inside, backup)

    Access-group interface inside INSIDE_OUT

    Access-group OUTSIDE_IN in interface outside

    Route outside 0.0.0.0 0.0.0.0 196.1.1.2 1 track 10

    Route outside 0.0.0.0 0.0.0.0 197.1.1.2 254

    Timeout xlate 03:00

    Pat-xlate timeout 0:00:30

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    identity of the user by default-domain LOCAL

    Enable http server

    http 192.168.200.0 255.255.255.0 inside

    http 192.168.202.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    monitor SLA 100

    type echo protocol ipIcmpEcho 212.58.244.71 interface outside

    Timeout 3000

    frequency 5

    monitor als 100 calendar life never start-time now

    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    outside_map interface card crypto outside

    backup_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    backup of crypto backup_map interface card

    Crypto ikev1 allow outside

    Crypto ikev1 enable backup

    IKEv1 crypto policy 10

    authentication crack

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 20

    authentication rsa - sig

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 30

    preshared authentication

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 40

    authentication crack

    aes-192 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 50

    authentication rsa - sig

    aes-192 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 60

    preshared authentication

    aes-192 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 70

    authentication crack

    aes encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 80

    authentication rsa - sig

    aes encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 90

    preshared authentication

    aes encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 100

    authentication crack

    3des encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 110

    authentication rsa - sig

    3des encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 120

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 130

    authentication crack

    the Encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 140

    authentication rsa - sig

    the Encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 150

    preshared authentication

    the Encryption

    sha hash

    Group 2

    life 86400

    !

    track 10 rtr 100 accessibility

    Telnet 192.168.200.0 255.255.255.0 inside

    Telnet 192.168.202.0 255.255.255.0 inside

    Telnet timeout 5

    SSH 192.168.202.0 255.255.255.0 inside

    SSH 192.168.200.0 255.255.255.0 inside

    SSH 0.0.0.0 0.0.0.0 outdoors

    SSH timeout 15

    SSH group dh-Group1-sha1 key exchange

    Console timeout 0

    management-access inside

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    internal group vpntunnel strategy

    Group vpntunnel policy attributes

    Ikev1 VPN-tunnel-Protocol

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list vpntunnel_splitTunnelAcl

    field default value green.com

    internal vpntunnell group policy

    attributes of the strategy of group vpntunnell

    Ikev1 VPN-tunnel-Protocol

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list gbnlvpntunnell_splitTunnelAcl

    field default value green.com

    Green user name encrypted BoEFKkDtbnX5Uy1Q privilege 15 password

    attributes of user name THE

    VPN-group-policy gbnlvpn

    tunnel-group vpntunnel type remote access

    tunnel-group vpntunnel General attributes

    address VPNPOOL pool

    strategy-group-by default vpntunnel

    tunnel-group vpntunnel ipsec-attributes

    IKEv1 pre-shared-key *.

    type tunnel-group vpntunnell remote access

    tunnel-group vpntunnell General-attributes

    address VPNPOOL2 pool

    Group Policy - by default-vpntunnell

    vpntunnell group of tunnel ipsec-attributes

    IKEv1 pre-shared-key *.

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns migrated_dns_map_1

    parameters

    maximum message length automatic of customer

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the migrated_dns_map_1 dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    Review the ip options

    !

    global service-policy global_policy

    context of prompt hostname

    no remote anonymous reporting call

    call-home

    Profile of CiscoTAC-1

    no active account

    http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

    email address of destination [email protected] / * /

    destination-mode http transport

    Subscribe to alert-group diagnosis

    Subscribe to alert-group environment

    Subscribe to alert-group monthly periodic inventory

    monthly periodicals to subscribe to alert-group configuration

    daily periodic subscribe to alert-group telemetry

    Cryptochecksum:7c1b1373bf2e2c56289b51b8dccaa565

    Hello

    1 - Please run these commands:

    "crypto isakmp nat-traversal 30.

    "crypto than dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 Road opposite value.

    The main issue here is that you have two roads floating and outside it has a better than backup metric, that's why I added the command 'reverse-road '.

    Please let me know.

    Thank you.

  • 3500 x vpn tunnel

    I need to establish a vpn connection between my office and a computer over the internet, allowing access to the internal of the outside lan. I have a problem with my router and I am looking for a new.

    Can I use x 3500 to establish a pptp vpn tunnel or it can work only as vpn passthrough?

    This modem/router supports VPN passthrough for IPSec, PPTP and L2TP only. Try VPN Linksys Gigabit routers like the series of the LRT.

  • RV042 VPN tunnel with Samsung Ubigate ibg2600 need help

    Hi all, ok before I completely remove all of my hair, I thought stop by here and ask the volume for you all with the hope that someone can track down the problem.

    In short I am configuring a 'Gateway to gateway' vpn tunnel between two sites, I don't have access to the config of the router from Samsung, but the ISPS making sure that they followed my setup - watching newspapers RV042, I don't however see the reason for the failure - im no expert vpn...

    Sorry if the log file turns on a bit, I didn't know where the beginning and the end was stupid I know... any advice would be greatly welcomed lol.

    System log
    Current time: Fri Sep 2 03:37:52 2009 all THE Log Log Log Log VPN Firewall Access system
     
    Time
    Type of event Message
    2 sep 03:36:01 2009 value of VPN Log [Tunnel negotiation Info] Inbound SPI = c3bdba08
    2 sep 03:36:01 2009 value of outbound SPI VPN Log [Tunnel negotiation Info] = c664c1ca
    2 sep 03:36:02 2009 VPN Log [Tunnel negotiation Info] > initiator send fast Mode 3rd package
    2 sep 03:36:02 2009 VPN Log [Tunnel negotiation Info] Quick Mode Phase 2 SA established, IPSec Tunnel connected
    2 sep 03:36:02 2009 VPN journal Dead Peer Detection start, DPD delay = timeout = 10 sec 10 sec timer
    2 sep 03:36:02 2009 VPN received log delete SA payload: ISAKMP State #627 removal
    2 sep 03:36:02 2009 VPN Log Main Mode initiator
    2 sep 03:36:02 2009 VPN Log [Tunnel negotiation Info] > Send main initiator Mode 1 package
    2 sep 03:36:02 2009 charge of VPN journal received Vendor ID Type = [Dead Peer Detection]
    2 sep 03:36:02 2009 VPN Log [Tunnel negotiation of Info]< initiator="" received="" main="" mode="" 2nd="" packet="">
    2 sep 03:36:02 2009 VPN Log [Tunnel negotiation Info] > initiator send Mode main 3rd package
    2 sep 03:36:03 2009 VPN Log [Tunnel negotiation of Info]< initiator="" received="" main="" mode="" 4th="" packet="">
    2 sep 03:36:03 2009 Log [Tunnel negotiation Info] VPN > main initiator Mode to send 5 packs
    2 sep 03:36:03 2009 Log [Tunnel negotiation Info] VPN > initiator receive hand Mode 6 Pack
    2 sep 03:36:03 2009 log VPN main mode peer ID is ID_IPV4_ADDR: '87.85.xxx.xxx '.
    2 sep 03:36:03 2009 Log [Tunnel negotiation Info] VPN Mode main Phase 1 SA established
    2 sep 03:36:03 2009 log VPN [Tunnel negotiation Info] initiator Cookies = c527 d584 595 c 2c3b
    2 sep 03:36:03 2009 log VPN [Tunnel negotiation Info] responder Cookies = b62c ca31 1a5f 673f
    2 sep 03:36:03 2009 log quick launch Mode PSK VPN + TUNNEL + PFS
    2 sep 03:36:03 2009 Log [Tunnel negotiation Info] VPN > initiator send fast Mode 1 package
    2 sep 03:36:04 2009 VPN Log [Tunnel negotiation of Info]< initiator="" received="" quick="" mode="" 2nd="" packet="">
    2 sep 03:36:04 2009 value of VPN Log [Tunnel negotiation Info] Inbound SPI = c3bdba09
    2 sep 03:36:04 2009 value of outbound SPI VPN Log [Tunnel negotiation Info] = e3da1469
    2 sep 03:36:04 2009 VPN Log [Tunnel negotiation Info] > initiator send fast Mode 3rd package
    2 sep 03:36:04 2009 VPN Log [Tunnel negotiation Info] Quick Mode Phase 2 SA established, IPSec Tunnel connected
    2 sep 03:36:04 2009 VPN journal Dead Peer Detection start, DPD delay = timeout = 10 sec 10 sec timer
    2 sep 03:36:05 2009 VPN received log delete SA payload: ISAKMP State #629 removal

    PFS - off on tada and linksys router does not support the samsung lol! connected!

  • Allowing ports through a VPN tunnel question

    I have a VPN tunnel established and I can ping above but my application fails and I think its because I encouraged not 2 ports (ports TCP 19813 and 19814) through. I'm not clear how should I do for allowing these ports through. I need to add a statement to permit to access my list 'sheep' or what I need to add a statement of license to my list of access interface "external"?

    Remote users have an IP address of 172.16.5.x 24 and they're trying to connect to users on the 192.168.200.x 24 192.168.201.x 24. I can't do a ping of the 24 192.168.200.x to the 172.16.5.0/24.

    The commands below are what I currently have in my PIX.

    My current sheep-access list:

    IP 192.168.201.0 allow Access-list sheep 255.255.255.0 172.16.5.0 255.255.255.0

    IP 192.168.200.0 allow Access-list sheep 255.255.255.0 172.16.5.0 255.255.255.0

    My current outside of the access-list interface:

    acl_inbound list access permit tcp any host xx.xx.xx.xx eq smtp

    acl_inbound list access permit tcp any host xx.xx.xx.xx eq - ica citrix

    acl_inbound list access permit tcp any host xx.xx.xx.xx eq www

    acl_inbound list access permit tcp any host xx.xx.xx.xx eq www

    acl_inbound list access permit tcp any host xx.xx.xx.xx eq www

    acl_inbound list access permit tcp any host xx.xx.xx.xx eq 500

    acl_inbound esp allowed access list any host xx.xx.xx.xx

    acl_inbound list access permit icmp any any echo response

    access-list acl_inbound allow icmp all once exceed

    acl_inbound list all permitted access all unreachable icmp

    acl_inbound list access permit tcp any host xx.xx.xx.xx eq www

    acl_inbound list access permit tcp any host xx.xx.xx.xx eq https

    first of all, you disable the commnad "sysopt connection permit-ipsec" on the pix? with this enabled command, which is enabled by default, the pix will ignore any ACLs for encrypted traffic. so if you have Hell no this command, then the acl that you applied on the outside int won't make a difference.

    However, if "sysopt connection permit-ipsec" is always on, and then all the port/protocol should be allowed.

    you said you could do a ping of 192.168.200.0 to 172.16.5.0. How about you 172.16.5.0 to 192.168.200.0 and 192.168.201.0?

    also, just wondering if the vpn lan-to-lan or access remote vpn (i.e. using the cisco vpn client).

  • NAT, ASA, 2 neworks and a VPN tunnel

    Hello. I have a following question. I am trying to establish a VPN tunnel to a remote network used to be connected to our via a VPN tunnel. The problem is that the previous tunnel their share has been created for the x.x.x.x our coast network which will serve no more time a month, but is currently still active and used. As I'm trying to get this VPN tunnel as soon as possible without going through all the paperwork on the other side (political, don't ask) is it possible to make NAT of the new network in the network x.x.x.x for traffic through the VPN tunnel.

    Something like this:

    new network-> policy NAT in old x.x.x.x fork on ASA-> VPN tunnel to the remote network using x.x.x.x addresses

    It is possible to add the new policy, but sometimes it can conflict with the former.

Maybe you are looking for

  • In Thunderbird/Tools/Options/Composition/spelling, language drop-down-box is not available, and the language line is empty.

    The drop-down-box languages chose is display of pale color that this option is not available. Clicking on it does nothing. In addition, no language appears in the language line. Not being able to use the drop-down-box fact by following the instructio

  • store the value obtained in the while loop

    Hello I'm data acquisition (1,000 points every 0.1 s) in a while loop. I would like to calculate the average y of the first sample of 1000 points when I click on a Boolean 'calibrate', store that value somewhere (outside the while loop?) so that it c

  • Assign Scripts to buttons during Installation

    I recently started to support a customer who has tiara installed over a number of workstations (mainly v8, some v8.1). They have developed hundreds of custom scripts (AUT mainly, but also some VBS), and at the present time, the installation process i

  • Rendering bug

    Hello world today I faced a system bug: only half of a BitmapField is rendered on the screen. I know that BB is full of bugs, and it is not the first time that I met.  Maybe some of you know how to defeat it or possible reason? Is there a bugtracker

  • Capture keypress after the selection of the custom in Message App Menu

    I added a custom application of message menu. It works fine but I need to figure out how to capture the user input to the ESC key once they clicked on my custom menu in order to clean and put an end to my library. This is my custom menu code: //Run i