cRIO shared after the restart Variable

Similar Questions

• I continued to have this message flashing on the screen "ERROR of LOADING of THE OPERATING SYSTEM" after the restart when loading the software Window XP.

  Original title: someone help please?

  Working on my old computer, a pentium 4, card mother GA81PE1000, I continued to have this message flashing on the screen "ERROR of LOADING of THE OPERATING SYSTEM" after the restart when loading the software Window XP. After so many years, working on the construction of computer & repair, it's new to me.

  So I checked the Microsoft Website for answers from people with the same problem in the past and apply their suggestions, nothing works... hard drive replaced, the changed value in the bios, did everything possible, still nothing works, phenomenal for me, please help me find an answer, thank you?

  Hello

  1. have you made changes on the computer before this problem?
  2 - what you want to say that you receive this error message during the installation of Windows XP?

  Check to see if the following is useful.

  Method 1: Disconnect all devices non-essential connected to the computer and restart. Check to see if it boots normally.

  Method 2: You may need to check the settings of the BIOS (Basic Input\Output System). Check if the hard drive is detected. If this is not the case, check the physical connections. Refer to the manual to check the same.

  Warning of the BIOS:

  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  The following article might be useful: "Error loading operating system" Error Message When you restart your computer during installation

• How can I find my username and password for Windows xp media center? don't remember setting but cannot get back in after the restart.

  How can I find my username and password for Windows xp media center? don't remember setting but cannot get back in after the restart.

  Hi Carol_971,

  1. Did you the latest changes on the computer?
  2. You have security software installed on the computer?

  Method 1

  I suggest that you try to start in safe mode and then try to log on to Windows using the default Administrator account and then remove the password for your account, check if it helps.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Method 2

  If you are unable to log on to Windows in safe mode, refer to the article below and then try the steps mentioned, check if it helps.

  How to connect to your Windows XP-based computer if you forget your password or if your password expires

  http://support.Microsoft.com/kb/321305

• Whenever I try to enter KB2559049 it always gets back after the restart, saying "NOT CONFIGURED".

  original title: HELP... (seniors not if nobody PC)!

  Whenever I try to enter KB2559049 it always gets back after the restart, saying "NOT CONFIGURED" and then it lands in the updates page... So I used the Microsoft Fix - it tool and she is 'THE PLACE WHERE WINDOWS STORES DATA has CHANGED AND MUST BE FIXED... CHANGE OF PLACES in UPDATE from WINDOWS to THE SETTINGS by DEFAULT in WINDOWS'... well I think, but I don't know how the making and tool Fix - it didn't tell me how is... Please someone can help me to what is necessary.

  Hello

  I suggest you to follow these steps and check if that helps:

  Method 1:

  If you have installed a security software on the computer, then I suggest you try to disable temporary and check to see if the same problem happens. Make sure that you enable security software back once the diagnosis is made to prevent the computer from virus attacks.
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Method 2:

  Try to download the update from this link and install the update manually and check if it helps:

  http://www.Microsoft.com/download/en/default.aspx

  It will be useful.

• VIB not updated after the restart - ESX6

  Hello

  I have a strange problem while updating to ESXi600-201511401-BG on 1 of 3 guests. It seems that the fix is installed correctly, but it disappears on the next reboot.

  
  

  The commands I tried to help include, but none of them seems to work:

  esxcli software update /vmfs/volumes/path/Update/ESXi600-201511001.zip esx-base - d - n vib

  and

  Profile of esxcli update d software /vmfs/volumes/path/Update /ESXi600 - 201511001.zip - p ESXi - 6.0.0 - 20151104001-standard

  The result is:

  Message: The update completed successfully, but the system must be restarted for the changes to be effective.

  Restart required: true

  VIBs installed: VMware_bootbank_esx - base_6.0.0 - 1.22.3247720

  VIBs removed: VMware_bootbank_esx - base_6.0.0 - 1.20.3073146

  VIB list after installation check seems to be updated, but after the restart, he returned to the old version.

  All guests were built fresh at about the same time using the same media however, this server has a problem. By comparing each server the only difference in VIBs is VMware_bootbank_esx-base. Everything else is the same...

  Any help would be appreciated.

  Thank you

  Derek

  VMware technical support identified the error "MSI - X not supported by the device" in boot.gz and recommended to update firmware or try to reinstall. As the host was running the same firmware as the hosts who have been updated and not happy with the way recommended reconstruction of the host, I did some research in error.

  A bit of googling suggests that the error relates to USB interrupts, which lead me to realize that it was the only server currently connected to a 16 ATEN KVM (cables VGA/USB) port. After unplugging the KVM, I was able to apply successfully the update...

  If anyone else has this problem and has devices connected to USB ports, I would disconnect them and try the upgrade again.

• Deploy shared in the installer Variablie

  I'm having a problem with a variable shared in my application.  This application is integrated with a Setup program must be installed on a machine without labview.  After looking around, I came across this link and think it is close to what I need.  The only difference is that the link refers to an executable file, and the next step is what throws me:

  1. Use the entry path of the library to invoke node to point to the library (s) containing your shared variables. If the library (s) have been included in the support directory of the executable as indicated above, the (s) library will be copied to the folder data the executable.  The point of the entry path to the (s) library.

  Because I do not use an executable file, I don't have not a folder 'data' to point the invoke node to.  I'm sure that other people must have experience this problem and am very curious to hear how it was resolved.

  See you soon!

  As a follow-up, I found this link which can clarify the situation a little more.

  Shared variables and stand-alone Applications or shared libraries

  If you plan to distribute a stand-alone application that uses shared variables, do not include the file .lvlib in a LAW degree or the executable file. Use the page settings of the Source file of the Application Properties dialog box to change the Destination of the file .lvlib to a destination outside the executable or the LLB. You can deploy shared variables in two ways:

  • Write the application so that it deploys programmatically variable shared at the start time. Call the library to deploy method in the first level VI of the application. In the entrance to the library path of the method, use the relative path to the .lvlib file that contains the shared variable.
  • Deploy the variable shared on the computer or target engine shared Variable before running the application built manually.

  If you plan to distribute a shared library that uses shared variables, do not include the .lvlib file in the shared library. Use the dialog box properties of the shared library File Source settings page to change the Destination of the file .lvlib to a foreign destination to the shared library.

• File deleted on esxi system after the restart with the last patch (256968)

  Hello

  Since I installed latest patch on esxi (build 256968), every time that I reboot server esxi, I lost the files in / opt and the .ssh folder.

  Before this patch, the files were still there on reboot.

  Do you have any idea what's going on? Is this a new limitation of free esxi?

  I ' am, using this file to VM backup with ghettovcb and everything works fine (until I reload )

  Thank you.

  This is provided with ESXi, there is difficulty set of files, including any of the local VMFS volumes that are kept at the restart. There is a cronjob schedule that works for the configuration files important backup automatically at a local bootbank, which is then loaded after the next reboot, all files created by the user and most likely using the Busybox does not support console will not survive a restart by default.

  If you use the ghettoVCB.sh - Free alternative for backup of VMS to ESX (i) 3.5, 4.x & 5.x , recommendation would be to store the script and all relevant files is the local VMFS volume or on the shared storage (NFS, iSCSI/FC SAN) volume.

  There is a script in "/sbin/auto-backup.sh" that you can actually run to see what files are being backed up, you can easily modify this script to save additional files which will ensure that they are saved on a restart.

  =========================================================================

  William Lam

  VMware vExpert 2009,2010

  VMware scripts and resources at: http://www.virtuallyghetto.com/

  Twitter: @lamw

  repository scripts vGhetto

  Introduction to the vMA (tips/tricks)

  Getting started with vSphere SDK for Perl

  VMware Code Central - Scripts/code samples for developers and administrators

  VMware developer community

  If you find this information useful, please give points to "correct" or "useful".

• cancelled downloads keep coming back after the restart

  Hello guys. After the Update beta, beta 9 if I remember well (on the section of the said browser ver 32) downloads are badly behave. the first problem I have encountered is when I downloaded a (approximately 40 KB) zip file, the zip is downloaded on the pc I could open it year everything was ok, but in firefox download, he showed that the download. I tried both download and open the zip option. After that I tried to download something else and everything was ok. the real problem is when I try to delete the download or cancel nothing happens. I restarted the browser and downloads are still suspended. How can I solve this problem?

  Note that the source code of Firefox shows that this has been done deliberately.

  • http://MXR.Mozilla.org/Mozilla-beta/source/browser/app/profile/Firefox.js

  972 // Turn off remote lookups in beta and stable channel.
  973 #ifndef RELEASE_BUILD
  974 pref("browser.safebrowsing.appRepURL", "https://sb-ssl.google.com/safebrowsing/clientreport/download?key=%GOOGLE_API_KEY%");
  975 #endif

• After the restart, firefox starts slowly, a script is not responding and answers continually.

  Hi everyone, I have a true glance.

  My firefox has always worked fine before, but I had to do a factor reset on my laptop and now there is a serious problem.

  After installed, firefox works fine, but after a restart of the computer, it hangs, becomes sensitive and always this message after only 2-3 mins "script is unresponsive script: chrome://browser/content/tabbrowser.xml.2425 ' either press on continue or stop the script does not stop at his lack of reaction

  This problem occurs in Firefox and Windows safe mode. I do not have Add ons installed and I also scanned for malware and there is not. I tried to reinstall clean without result.

  Any help much appreciated!

  In this case the Firefox homepage integrated display and no other site?

  In order to exclude Flash as a potential culprit, could you try one or two of the following ways:

  (1) disable the Safe_mode of the Flash Player plugin.

  The following pages provide different ways to do this:

  • Adobe technical support under the heading of 'Last resort' article: Adobe Forums: how to fix protected Flash Player for Firefox mode?
  • Manual steps: https://support.mozilla.org/questions/968190?page=5#answer-509209
  • Batch file to automate the manual steps: https://support.mozilla.org/questions/982093#answer-518078

  Flash must unload completely from memory (Firefox restart might help) before it would take effect.

  (2) the value of Flash Click-to-Play ("ask to activate").

  This will delay the Flash start on a page, until you approve, which will distinguish the questions generated by Flash to load and layout problems.

  To set 'Ask to activate', open the page modules using either:

  • CTRL + SHIFT + a
  • Firefox orange (or the Tools menu) button > Add ons

  In the left column, click on Plugins. Search 'Shockwave Flash' and always change 'enable' to 'ask to activate '.

  When you visit a site that wants to use the Flash, you should see a notification in the address bar icon and one of the following: a link in a black rectangle in the page or an information bar slides between the toolbar and in the page area.

  Any improvement in these scenarios?

• The system time has changed after the restart of Bootcamp

  Hello

  After a restart of the boot camp partition Windows 10. I have the wrong time, in fact its always an hour later that it is.

  Although in the Control Panel, I checked the "time of to of Appleserver" it does not update the time of its actual value. Parenthesis in Win 10 (BootCamp) time is correct, then the difference that happens just restart in Mac OS.

  System:

  MacBook Pro early 2011

  OS X El Capitan 10.11.3

  Bootcamp

  Win 10 latest version with all updates/Updates aviable

  What could be the problem?

  Thanks for your help!

  Set the time zone correctly on OSX and Windows.

• I'm having problems after the restart with docking station, applications, etc.

  OS X: 10.11.3

  Mac Pro 2010 2 x 2, 66 GHz 6-Core

  Graphics NVIDIA Quadro 4000 card

  24 GB Ram

  50 GB of free memory

  4 additional hard disks

  Hello community,

  I have a strange problem, after the mac is restarted, even when I decide not to join his joined apps a former State of the saved request. I can't make changes to the dock, after restart it restores an old state. When I try to import or save something in any application you see normally last modified files, yet his watch an old state. When I try to delete files that I always put my password, it's new. Im confused, I'm a long-time os x user since 1999 has never had this kind of problems.

  Help, please.

  Lars

  Please, back up all data before proceeding.

  This procedure will unlock all your user (not system files) files and reset their ownership, permissions and default access controls. If you have voluntarily set special values for these attributes on any of your files, they will be be restored. In this case, either stop there, or be ready to recreate the settings if necessary. Do that after checking these settings that did not cause the problem. If none of that is meaningful to you, you need not worry about this, but do not follow the instructions below.

  Step 1

  If you have more than one user, and the one in question is not an administrator, then go to step 2.

  Triple-click anywhere in the next line to this page to select this option:

  sudo find ~ $TMPDIR.. -exec chflags -h nosappnd,noschg,nosunlnk,nouappnd,nouchg {} + -exec chown -h $UID {} + -exec chmod +rw {} + -exec chmod -h -N {} + -type d -exec chmod -h +x {} + 2>&-

  Copy the selected text in the Clipboard by pressing Control-C key combination.

  Launch the Terminal application integrated in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  Paste in the Terminal window by pressing Command + V. I tried these instructions only with the Safari browser. If you use another browser, you may need to press the return key after pasting.

  You will be asked your password of connection that are not displayed when you type. Type carefully, and then press return. You can get a warning to be careful. If you do not have a password, you will need to configure one before you can run the command. If you see a message that your user name "is not in the sudoers file", then you have not logged as an administrator.

  The command may take several minutes to run, depending on the number of files you have. Wait for a new line ending with a dollar sign ($) to appear, and then quit Terminal.

  Step 2 (optional)

  Take this step only if you have trouble with the phase 1, if you prefer not to consider, or if this does not resolve the problem.

  Start in recovery mode. You may be prompted to select a language, then the OS X Utilities appears.

  If you use FileVault 2, select disk utility, then select the icon for the volume FileVault startup ("Macintosh HD", unless you have given it a different name.) It will be nested under another icon of the disc. Click the Open button in the toolbar and enter your login password when you are prompted. Then quit disk utility must be returned to the main screen.

  Select

  Utilities ▹ Terminal

  in the menu bar. It will open a Terminal window. In this window, type this:

  resetp

  Press the tab key. The partial order you entered will automatically end this:

  resetpassword

  Press return. Opens a window to reset the password. You do not need to reset a password.

  Select your boot volume ("Macintosh HD", unless you have given it a different name) if not already selected.

  Select your username in the menu option allows you to select the account if not already selected.

  Under Reset Home Directory Permissions and ACLs, click the reset button.

  Select

  ▹ Restart 

  in the menu bar.

• VN7 - 591G - may depend on internet sharing after the update to windows 10

  As I said that I can't turn on the sharing of the internet after I upgraded my Nitro V 10 Windows, it says "wireless card driver doesn't support the AP." I have updated the wifi driver, but still have the same result...

  I tried installing the windows version 8 of the driver and got good results
  It is compatible and that you have not noticed problems

• Printer is no longer available through sharing after the change of name of PC.

  share a printer after changing the name of the pc

  I have 5 (4 XP Pro, 1 Win7) PC with shared printer and file sharing.  The names of PC were not intuitive and I changed the more meaningful names.  File sharing has continued to work, but the printer was more likely to assessment.  He was always playing on the remote PC but the slightest mistake out.  From a command prompt, I could print to it from a remote PC using the new name of PC, but not from Windows XP.  The printer is connected to the Win7 PC.  I tried to use XP search for the dialog new printer and it OCHA see the printer on Win7 but then would error saying that there was not.  I changed the name on the Win7 machine and printing resumed again of the XP machines.

  I need to be able to change the name of the Win7 PC and power find the shared printer on the XP machines using the new name of the Win7 machine which has the printer.

  Been struggling with this for 3 days, through forums and other sites and found nothing.

  Thank you

  Uninstall and reinstall the printer again.

  Windows is most likely trying to still access the old computer name.

• Vista goes into sleep mode automatically just after the restart

  The following problem was irregular. Sometimes, other times not. I'm totally frustrated as to why it is happening and I would like to solve this problem, now and forever.

  Yes, first facts: I have an Asus G71Gx laptop game with Nvidia Geforce GTX 260 M. 6 GB of memory, Windows Vista 64-bit. Do not think that other information is necessary, unless I'm mistaken.

  The problem: well, just after the start/start my laptop goes into sleep mode. As in, Windows starts fine and I see my desktop with all the shortcut icons and the background, and then all of a sudden the screen goes black (with two Dim lights blue on the screen - fellow Asus G71Gx users will know it), and the power led button flashes slowly in and out, as if it was in sleep/hibernation. The led light cover mode monitor "sleep". I did the whole "all never put under power options. I've updated my Nvidia graphic drivers for later. I even disabled Hibernate in the command prompt. Seriously, I have above average PC knowledge. But it has trampled me... everything short.

  Sometimes, I have to go through this cycle up to 9 or 10 times and then stops. Other days there is no question. But I still have to reboot just to be safe and to avoid the game stutter (another question that I don't know what it is, since I was the latest GPU drivers). But I can live with that.

  It cannot be an overheating GPU. I mean, it's at the start and at the present time, it is cold enough to have this piece as a cooler for the GPU! Haha.

  I thought about possible power supply problems. But how to test it? The laptop doesn't have it, the first week I got it. I use an adapter to put the American card in European decision-making.

  It is the ONLY major problem I have with this laptop. Sleep at startup. The other two, being game stutter if I don't restart my laptop and double tapping (seems to be an Asus problem according to the forums), are quite minor and I can live with that.

  Any help with this would be GREATLY appreciated. I'm VERY tempted to get windows 7 and do a clean install, but Vista was not really giving me any problems. But if I know that this issue is associated with Vista, then I say Bravo to Vista...

  Edit: Apologies for writing this thread Windows 7 and explore the internet forum. Don't know how it happened! Well I'm leaving here now, and hopefully this will get sorted.

  After 2 replacements of mobo that apparently caused this same prob, what finally fixed for me has been updated the chipset drivers.

• changes made to the Bundle.js file will disappear after the restart of the AAU

  Nice day
  
  I add javascript code in the file bundle.js in the following path: domain_home\ucm\cs\weblayout\resources\bundle.js .
  the changes are reflected on the University Complutense of MADRID fine, but once the server of the University Complutense of MADRID has reformulated the changes disappeared and the file back to back such; without my changes.
  
  the code that I want to add is:
  
  If ((typeof gamme! == 'undefined') & &!) Range.prototype.createContextualFragment) {}
  Range.prototype.createContextualFragment = {function (html)}
  Frag var = document.createDocumentFragment ();
  div var = document.createElement ('div');
  frag.appendChild (div);
  div.outerHTML = html;
  return of frag;
  };
  }
  
  I want to add because I have a javascript like this error: object does not support property or method 'createContextualFragment', this erro has occurred when the version of Internet Explorer is V.9. ; no javascript errors appear on the Version 8. When I add this piece of javascript in the bundle.js file, it the error disappeared and everything's fine, but as I said earlier after restart of the AAU extra javascript code is over and disappear from the file bundle.js.
  
  For this reason, I wanted to ask, is there a way so that my code and will remain even after reboot? Or is the file downloaded on the restart of a different path?
  
  Any Suggestions?

  It's actually quite simple to explain:

  - domain_home\ucm\cs\weblayout\resources is a directory that contains the version of the runtime resources
  -If you want to persist your changes, you will need to do it in a source directory. 11 g, there are two directories source; one of the standard components and the other for those custom. You must use the latter
  -in fact, if you create a custom component wizard, make your changes it and activate the component, you should be done. The only other thing that you should pay attention is the loadOrder of your resource setting - it should be higher applies.

  For more details, see http://docs.oracle.com/cd/E23943_01/doc.1111/e10807/part4_customize_comp.htm#sthref522