Crucial memory works not

Similar Questions

• A channel memory works not repairable... no?

  OK, so I've reduced my memory problem (you know, of the post on the motherboard does not start, where my system was recognizing only 16 GB, 24 GB) to a channel on the motherboard does not recognize it. I tried 1 token at once in the A1 location, until I had checked that all six bullets started properly at 4 GB. Then I glued a chip in A1 (because the mobo requires a chip in A1 to start), and one stuck chips in other passers-by, A2, B1, B2, C1 and C2 and discovered that, whenever I put a chip in another location, the mobo would recognize 8 GB of memory, as it should be... except slots B1 and B2. These slots were not at all recognized by my BIOS.

  So, apparently, that this channel is not picking up the memory... can be done to fix this? FWIW, CPU - Z from CPUID sees all 24 GB of memory, so somehow they work at least partially... it's just the system BIOS and Windows that cannot pick it up. It also worries me because not only I do not receive my full 24GO, but I do not also get advantage of the increase in the speed triple-channel...

  I tried the BIOS from the top down, and there is no setting it that limits which channels is turned on... so I'm stumped. Ideas?

  BTW, the mobo is the Asus P6T6 WS Revolution with an Intel i7 - 920 (D0) CPU. I am also running a GTX 580 and a GTX 285 and one Raid card.

  So, it turns out that my system is still under warranty (four!) so they are shipping me a new mainboard... sweet!

• 3 beeps, 5 seconds silence, 3 beeps, etc change the memory did not help...

  Mac Mini end of 2012 running El Capitan

  With 3 beeps, 5 seconds silence, 3 beeps, etc, it's "no good bank."  I was using crucial memory, works fine until about a week ago when he is awakened from his sleep gave the order to 3 beeps.  Changed to original memory of apple, same, got crucial replacement memory, same 3 beeps...  I doubt that all the 3 series were / are bad.  What else could be?  Any hardware problem would give sequence 3 beeps?

  Probably the logic board is having some problems caused by the bad memory or another problem. I would certainly get extract in an Apple Store or service provider.

• 512 MB memory upgrade not working - Hp Pavilion 6835

  Hello ladies and gentlemen,

  I have a HP pavilion 6835

  It has only 2 slots = memory and there are currently 2 simms 128 MB and 256 MB = and the computer works fine

  Recently, I bought two - 256 mb chips bringing the total to 512 MB.

  I put the memory and it doesn't now although the post test works by saying that it recognizes 511 MB of memory during the test of Post. (Yes its 100 mhz, synchronization, CL2 memory), and then it restarts itself. To do this, this reboot cycle and Post test over and over again, until you stop it.

  Please contact me with suggestions,

  Thanks for any help,

  Dave

  Here are the specifications of memory and the Ebay photo (it's where I bought it) article number: 120395265735

  Or search on ebay for this item number if this link does not work.

  Here are the specifications of memory:

  These are two matched sticks of 256 MB SDRAM PC100 (512 MB total). This memory works very well and is guaranteed against the DOA.

  Micron Tech

  MT16LSDT3264AG-10EB1

  Double-sided (16 chips)

  256 MB 100 MHz CL2
  

  PC100

  Unbuffered memory

  Non - ECC

  Message edited by Davegreat on 06/04/2009 23:03
  Message edited by Davegreat on 06/04/2009 23:14

  It works !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

  I've updated the BIOS (from 2.0 something (from 2000) this version 3.07 2001 or something I think.

  Followed the instructions in the Readme file for the update of the Bios.

  Add memory (256 MB strips)

  And it starts upui the first time without problem.

  I thank you for your patience and continues to offer solutions, when it seemed hopeless. You are all a great examples for how to help someone fix their HP computer.

  Thank you for your time and your expertise,

  Dave

• The instruction at "0x03925a9c" referenced memory at "0x03925a9c". The memory could not be written.

  I don't know why I continue to install the latest version when the previous version works fine, but I do. So this time it gave me an error when I start Skype... The instruction at "0x03925a9c" referenced memory at "0x03925a9c". The memory could not be written.

  The only options it gives me is to terminate the program or to debug, which one of the two closes just for Skype. I have not tried to make a call, same Skype2Skype, but I know very well, I can talk as long as I do not click on the OK or CANCEL buttons and just move the window behind the others, this is not a problem. I tried to uninstall Skype and resettlement and who does not. Even tried out hacking the registry, and the same error comes back upward after a reinstallation. I'd hate to reinstall my OS it takes do someday, because of all the programs that I need to install again. Don't know what I can do to solve this problem. I tried the MS registry Fixer thing and found some things and repaired them, but still does not solve my problem of Skype.

  Alternatively, you can first try to uninstall the currently installed version of 6.18 and install Skype 6.14.0.104 version:

  http://download.Skype.com/MSI/SkypeSetup_6.14.0.104.msi

• Satellite A100-828 - new module of memory does not

  Hello

  I recently bought 2x2gb modules for my A100-828. However, I can not any memory module to adapt to the second extension slot. I tried both the new modules in it that the old module of 512 MB which was originally in the laptop. The new memory is certainly compatible as two new modules work in the first expansion slot.

  Memory does not seem to fit properly in the second slot (I put in a good sense ad. it won't push back.)

  Anyone have ideas, what is the problem?

  Thanks for your help.

  Hello

  I put t know why do not the module in the second slot.
  The two sites are completely identical and also support the same standard.

  I think you used it just not compatible modules, or you have tried inserting modules backwards
  AFAIK you need DDR2 667 MHz (* PC2-5300 *) module SODIMM 200 PIN.

  What module do you use?

• Memory could not be "written".

  Hello

  I get this error "education at ' 0x03a65d88 ' referenced memory at ' 0x03a65d88 '.» "The memory could not be 'written '" Operating system is Windows Server 2003.

  I am trying:

  -Reinstall Skype (version 6.18.0.108)

  -Uninstall and install Skype

  -Rename %appdata%\skype folder, new created after running Skype

  -delete the folder %temp%\skype

  -remove the Skype folder in local contexts

  -uninstall, delete all records for Skype and then install Skype

  None of the work top. What's wrong?

  Thanks for the reply.

  The latest version of Skype 6.18 will not work on your system.

  The issue could have been resolved by installing the same 6.16.0.105 or Skype 6.14.0.104 version version.

  Unfortunately, Skype yesterday removed all links to old versions of Skype.

  Now, you must contact Skype Service customer to get your problems solved.

  How to contact Skype customer service

• Satellite A100: Norton error appears - memory could not be read

  0 x 02459962 referred memory 0x5902adf8 memory can not be read.

  This error keeps showing upwards.
  Can anyone help? He came to norton when I do a check up.
  Also, I get an error when I close internet explore tells me msvcr.80.dll is not found.

  Aside from that my laptop works ok, it is a satellite A100.

  Hello

  I think that this file msvcr.80.dll is part of the .NET Framework 2.0.
  I would try to install the version or see if you can do a repair on it via Add/Remove software.

  I studied and declined to find out why the error of Norton.
  But the address of memory does not help.
  However, it seems that you have installed something that might be a bad influence.

  Maybe a switching of the BONE at the beginning good point work would clear this issue.

• Pavilion DV5 2050CA: upgrade memory does not not about DV5 2050 this laptop computer

  The upgrade of 2 x 4 GB 2x2gb memory does not work. After installing the new memory modules, it starts and the HP Quickweb are visible. As a result, if I try to load Windows 7, he returned to the screen of Quickweb. If I install only these new memories (1x4Go config), I get the error Badpool header.

  The NOTE book details are:

  Model - DV2050CA

  Produnt number - WQ748UA #ABC,

  2.26 GHz, Intel i3 - 350 M processor

  Max - 8 GB of memory

  Details of the memory module are:

  Kingston ValueRAm-2 x 4 GB, PC-10600 1333 Mhz, DDR3, SDRAM, CL9 SoDIMM.

  Can some please help me make it work?

  Yes, computers laptops HP prefer the variety of low density of memory. This means that 8 black blocks of memory on the side of the chip, not 4.

  4 GB 599092-001

  Above is the part number of HP for a 4 GB module.

  

  http://www.Amazon.com/HP-VH641AT-4-GB-DDR3-PC3-10600/DP/B0030L3B8E/ref=sr_1_1?ie=UTF8&QID=1446634397&SR=8-1&keywords=599092-001

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Application error memory could not be read 0 x 00000014

  Hello world

  I would like to know if any of you have experienced this problem.

  I run an application built by me in a computer with LabVIEW Run-time 9 in which I display a PDF file using an ActiveX control:

  

  The target computer is running Adobe Reader 9.0.  Everything works perfectly until the application is closed.  From time to time (almost most of the time), I have the following error in windows:

  «Application error: the instruction at "0x0ffd609c" referenced memory at "0 x 00000014".»  The memory could not be "read".  Click OK to complete the program."

  Try to find the reason why, I found a few forums who say that the reason is a bug in Adobe 9.0 (in fact, I tried to run the application with Adobe Reader 8 and I can't make the same mistake).  Someone of you have had this error before and found a solution?  These links were not on LabVIEW and I have no idea how to get around this problem.

  Any help is happy.

  Thanks in advance.

  Dani

  Who may be interested, I managed to find a workaround for this bug in Adobe Reader 9.0.

  It seems that, somehow, LabVIEW and other programming tools, hang around with this version of Adobe (I guess it is because of this bug) when the reference to closing Adobe created by the ActiveX container.  That the solution will be closing "by hand" this reference, then saying Windows to release the whole relationship between the application (LabVIEW for us) and Adobe.  The idea is that when we did with VI which displays the PDF via ActiveX, we should close the reference to the ActiveX control, close the reference to the VI, and:

  -process all Windows messages currently in the queue of messages (.NET: System.Windows.Form.Application-> DoEvents)
  -run CoFreeUnusedLibraries in "ole32.dll".

  

  I hope this information can help someone, I lost too much time to understand this (eventually find the answer in an Adobe forum!)

  P.S. P.S. for those who program in c#, check out this link; He was my source.

• Memory could not be read after installing KB982524

  Has anyone understood why a happends "memory could not be read question" after you have installed this hotfix rolled-up/cluster .net when you exit an application? I'm guessing that it is used by another process. If so, are there plans to deploy a fix for this patch? If not, other than uninstalling it (KB976576 is the question), is there a workaround?

  Data sheet:

  Operating system: Windows Server 2003 sp2 but they have seen this problem on XP and Vista (all 32 bit)

  Antivirus: AVG 8.5... NOTE: some customers use it and others are using Norton and McAfee.

  NOTE: When you remove this patch, all the apps work as expected.

  Hi Gladius,
   
  Your question of Windows is more complex than what is generally answered in the Microsoft answers Windows 7 forums. It is better suited for the IT Pro TechNet public. Please post your question in theTechNet Forums.

  Kind regards
  Syed - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• "The instruction at 0x6c371c9d referenced memory at 0 x 00000038. The memory could not be read. "when I go to create a new pdf of the file after the installation of updates

  Original title: "the instruction at 0x6c371c9d referenced memory at 0 x 00000038. The memory could not be read. »

  I worked on a design project for a few days I made several pdf files from. During the night, Windows ran and installed the updates on my computer. (My design file was open at the time). Now, when I go to create a new pdf of the file, I get the following error code: "the instruction at 0x6c371c9d referenced memory at 0 x 00000038. The memory could not be read. »

  HELP - I can't find a solution.

  Thank you!!

  Hello

  1. what program you use for your design project?

  2. did you run the repair of this program?

  Perform System Restore on the computer and check if that helps.

• Error message: "the instruction at oxo656edab referenced memory at oxo6d20e8. The memory could not be read', play Pogo games.

  Original title: Pogo games

  I'm playing a game on pogo and when I try to activate a games, this warning comes up and won't let me play a game.  The warning States the following, "the instruction at oxo656edab referenced memory at oxo6d20e8.  The memory could not be read.   Help!  What should I do

  Hello Barb,

  1. you are trying to play games online?

  2 are you facing this problem when you play Pogo games?

  3. what web browser do you use?

  If you use Internet Explorer, then try the work around described in the following article:

  You may receive an error "memory could not be read" message when you click certain Web site links in Internet Explorer 6

  You can also read the following article and check if it helps.

  Internet Explorer is slow? 5 things to try

• Message error "memory could not be Read.

  I am running windows XP SP3, and whenever I play the multiplayer mode of the game (battlefield bad company 2), it crashes with the error: «the instruction at 0x0116df37 referenced memory at 0x0000000b0.» Memory could not be read. »
  Can someone help me with this problem? Essentially, it makes my game without value. :(
  Oh, and the guys over at support of the environmental assessment have been next to no help.

  I would also add that the single player mode for this game has worked smoothly, without any error.

  Hi MacRoss_14,

  ·         Have you had this problem with the game earlier?

  Method 1: Check to see if there are patches available for the game. Log on to the Web site of the manufacturer for the same thing.

  Method 2: Try to uninstall and then reinstall the game and check if this may help.

  In addition, you can check

  http://Forum.EA.com/eaforum/posts/list/660/380660.page

• Memory could not be written error

  Can someone help me with this error. It is when the Windows loading finishes, when you open my computer, and when you use the drop down to get a file.

  "the instruction at"0x00db5759"referenced memory at"0x00000000". the memory could not be written.

  Thank you

  b_bucky

  I had the same problem.  I got it back up to my HP printer driver installations.  I found this solution 2, step 1 of this HP link worked for me.  http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c00273968 .   Try to replace window Image Acquisition service automatic to manual.  See the link for instructions.