CSRSS. "BSOD" EXE Error"VISTA_DRIVER_FAULT.

Similar Questions

• BSoD 0x9f error code

  In recent weeks, my computer started showing a BSoD, titled State pilot failure, whenever I stop, and sometimes, when I restart.  The computer hangs on the closing down of the screen for at least ten minutes, until appears the BSoD, where making me one forced to close.  After having extensively searched through Microsoft' forums and topics of support I still have not found a solution.  I ran Debugging Tools for Windows to open a dump file, and it revealed an error code 0x9f with an ntoskrnl.exe image name.  She led me to believe that my ntoskrnl.exe is corrupted or out of date, but I know that it is not recommended to replace this program unless that busy on a Microsoft OS disc.  I bought my PC from Future Shop, so it isn't an OS disc.

  Some of the solutions related to this error message, he said that the problem was possibly linked to attached USB devices.  The only USB device I connected is an OCZ Eclipse Laser Mouse.

  The BSoD has a side effect that if she interrupts a reboot of the system that is required to complete the system configuration, it leaves such configurations what.

  My PC specs are:
  Manufacturer: gateway
  Model: FX6800 - 03 h
  OS: Windows Vista Home Premium 64-bit
  SP: Service Pack 2
  Processor: Intel Core i7 920

  Here is the report of the bucket.  I'm totally familiar with this program then please let me know what I can do to provide more information if required.

  Microsoft (R) Windows debug 6.11.0001.404 AMD64 Version
  Copyright (c) Microsoft Corporation. All rights reserved.

  Loading dump file [C:\Windows\Minidump\Mini091909-01.dmp]
  The mini kernel dump file: only registers and the trace of the stack are available

  Symbol search path is: * invalid *.
  ****************************************************************************
  * Loading of the symbol may be unreliable without a symbol search path.           *
  * Use .symfix to get the debugger to choose a symbol path.                   *
  * After adjusting your path to symbols, use .reload to refresh the locations of symbols. *
  ****************************************************************************
  Executable search path is:
  *********************************************************************
  * Symbols cannot be loaded because the path is not initialized. *
  *                                                                   *
  * The symbol path can be defined: *.
  * using the _NT_SYMBOL_PATH environment variable.                 *
  * with the help of the there when you start the debugger argument. *.
  * using the .sympath and .sympath + *.
  *********************************************************************
  Cannot load the image \SystemRoot\system32\ntoskrnl.exe, 0n2 error Win32
  WARNING: Unable to verify timestamp for ntoskrnl.exe
  ERROR: Module load completed but symbols can be loaded for ntoskrnl.exe
  Windows Server 2008/Windows Vista Kernel Version 6002 (Service Pack2) MP (8 procs) free x 64
  Product: WinNt, suite: TerminalServer personal TerminalServer
  Computer name:
  Kernel base = 0xfffff800 '02663000 PsLoadedModuleList = 0xfffff800' 02827dd0
  The debugging session: Fri Sep 17 23:57:05.741 2009 (GMT-7)
  System Uptime: 0 days 4:13:43.191
  *********************************************************************
  * Symbols cannot be loaded because the path is not initialized. *
  *                                                                   *
  * The symbol path can be defined: *.
  * using the _NT_SYMBOL_PATH environment variable.                 *
  * with the help of the there when you start the debugger argument. *.
  * using the .sympath and .sympath + *.
  *********************************************************************
  Cannot load the image \SystemRoot\system32\ntoskrnl.exe, 0n2 error Win32
  WARNING: Unable to verify timestamp for ntoskrnl.exe
  ERROR: Module load completed but symbols can be loaded for ntoskrnl.exe
  Loading the kernel symbols
  ...............................................................
  ................................................................
  ..........
  Loading user symbols
  Loading unloaded module list
  ....
  *******************************************************************************
  *                                                                             *
  * Bugcheck analysis *.
  *                                                                             *
  *******************************************************************************

  Use! analyze - v to obtain detailed debugging information.

  Bugcheck 1000009F, {4, 258, fffffa80078fa040, 0}

  The kernel symbols are FALSE. Correct symbols to do the analysis.

  *************************************************************************
  ***                                                                   ***
  ***                                                                   ***
  Your debugger is not using the appropriate symbols *.
  ***                                                                   ***
  In order for this command works correctly, your symbol path *.
  should point to .pdb files have the type information complete.      ***
  ***                                                                   ***
  Some (such as the public OS symbols) .pdb files are not *.
  contain the required information.  The contact group that *.
  you provided with these symbols, if you need this command for *.
  work.                                                          ***
  ***                                                                   ***
  Type referenced: nt! _KPRCB *.
  ***                                                                   ***
  *************************************************************************
  *************************************************************************
  ***                                                                   ***
  ***                                                                   ***
  Your debugger is not using the appropriate symbols *.
  ***                                                                   ***
  In order for this command works correctly, your symbol path *.
  should point to .pdb files have the type information complete.      ***
  ***                                                                   ***
  Some (such as the public OS symbols) .pdb files are not *.
  contain the required information.  The contact group that *.
  you provided with these symbols, if you need this command for *.
  work.                                                          ***
  ***                                                                   ***
  Type referenced: nt! _KPRCB *.
  ***                                                                   ***
  *************************************************************************
  *************************************************************************
  ***                                                                   ***
  ***                                                                   ***
  Your debugger is not using the appropriate symbols *.
  ***                                                                   ***
  In order for this command works correctly, your symbol path *.
  should point to .pdb files have the type information complete.      ***
  ***                                                                   ***
  Some (such as the public OS symbols) .pdb files are not *.
  contain the required information.  The contact group that *.
  you provided with these symbols, if you need this command for *.
  work.                                                          ***
  ***                                                                   ***
  Type referenced: nt! _KPRCB *.
  ***                                                                   ***
  *************************************************************************
  *********************************************************************
  * Symbols cannot be loaded because the path is not initialized. *
  *                                                                   *
  * The symbol path can be defined: *.
  * using the _NT_SYMBOL_PATH environment variable.                 *
  * with the help of the there when you start the debugger argument. *.
  * using the .sympath and .sympath + *.
  *********************************************************************
  *********************************************************************
  * Symbols cannot be loaded because the path is not initialized. *
  *                                                                   *
  * The symbol path can be defined: *.
  * using the _NT_SYMBOL_PATH environment variable.                 *
  * with the help of the there when you start the debugger argument. *.
  * using the .sympath and .sympath + *.
  *********************************************************************
  Probably caused by: ntoskrnl.exe (nt + 5cc7f)

  Follow-up: MachineOwner
  ---------

  0: kd > nt! _KPRCB
  ^ Syntax error in ' nt! _KPRCB'
  0: kd > referenced: nt! _KPRCB
  ^ Bad registry error in ' referenced: nt! _KPRCB'
  0: kd > nt! _KPRCB
  ^ Syntax error in ' nt! _KPRCB'
  0: kd > y
  ^ Syntax error in '-y'
  0: kd > _NT_SYMBOL_PATH
  ^ Syntax error in "_NT_SYMBOL_PATH.
  0: kd >! analyze - v
  *******************************************************************************
  *                                                                             *
  * Bugcheck analysis *.
  *                                                                             *
  *******************************************************************************

  DRIVER_POWER_STATE_FAILURE (9f)
  A driver is causing an inconsistent power state.
  Arguments:
  Arg1: 0000000000000004, the change in diet has expired waiting to synchronize with the Pnp
  subsystem.
  Arg2: 0000000000000258, the time-out in seconds.
  Arg3: fffffa80078fa040, the thread that currently holds the lock of Pnp.
  Arg4: 0000000000000000

  Debugging information:
  ------------------

  The kernel symbols are FALSE. Correct symbols to do the analysis.

  *************************************************************************
  ***                                                                   ***
  ***                                                                   ***
  Your debugger is not using the appropriate symbols *.
  ***                                                                   ***
  In order for this command works correctly, your symbol path *.
  should point to .pdb files have the type information complete.      ***
  ***                                                                   ***
  Some (such as the public OS symbols) .pdb files are not *.
  contain the required information.  The contact group that *.
  you provided with these symbols, if you need this command for *.
  work.                                                          ***
  ***                                                                   ***
  Type referenced: nt! _KPRCB *.
  ***                                                                   ***
  *************************************************************************
  *************************************************************************
  ***                                                                   ***
  ***                                                                   ***
  Your debugger is not using the appropriate symbols *.
  ***                                                                   ***
  In order for this command works correctly, your symbol path *.
  should point to .pdb files have the type information complete.      ***
  ***                                                                   ***
  Some (such as the public OS symbols) .pdb files are not *.
  contain the required information.  The contact group that *.
  you provided with these symbols, if you need this command for *.
  work.                                                          ***
  ***                                                                   ***
  Type referenced: nt! _KPRCB *.
  ***                                                                   ***
  *************************************************************************
  *************************************************************************
  ***                                                                   ***
  ***                                                                   ***
  Your debugger is not using the appropriate symbols *.
  ***                                                                   ***
  In order for this command works correctly, your symbol path *.
  should point to .pdb files have the type information complete.      ***
  ***                                                                   ***
  Some (such as the public OS symbols) .pdb files are not *.
  contain the required information.  The contact group that *.
  you provided with these symbols, if you need this command for *.
  work.                                                          ***
  ***                                                                   ***
  Type referenced: nt! _KPRCB *.
  ***                                                                   ***
  *************************************************************************
  *********************************************************************
  * Symbols cannot be loaded because the path is not initialized. *
  *                                                                   *
  * The symbol path can be defined: *.
  * using the _NT_SYMBOL_PATH environment variable.                 *
  * with the help of the there when you start the debugger argument. *.
  * using the .sympath and .sympath + *.
  *********************************************************************
  *********************************************************************
  * Symbols cannot be loaded because the path is not initialized. *
  *                                                                   *
  * The symbol path can be defined: *.
  * using the _NT_SYMBOL_PATH environment variable.                 *
  * with the help of the there when you start the debugger argument. *.
  * using the .sympath and .sympath + *.
  *********************************************************************

  ADDITIONAL_DEBUG_TEXT:
  Use '! findthebuild' command to search for the generation of target information.
  If the build information is available, run '! findthebuild s; .reload ' to set the symbol path and of loading symbols.

  MODULE_NAME: nt

  FAULTING_MODULE: fffff80002663000 nt

  DEBUG_FLR_IMAGE_TIMESTAMP: 49e0237f

  DRVPOWERSTATE_SUBCODE: 4

  FAULTING_THREAD: fffffa80078fa040

  CUSTOMER_CRASH_COUNT: 1

  DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT

  BUGCHECK_STR: 0X9F

  CURRENT_IRQL: 0

  LAST_CONTROL_TRANSFER: from 0000000000000001 to fffff800026bfc7f

  STACK_TEXT:
  fffffa60'01daf510 00000001' 00000000: 00000000'00000000 00000000'00000000 00000000'00000000 00000000'00000001: nt + 0x5cc7f
  fffffa60 '01daf518 00000000' 00000000: 00000000'00000000 00000000'00000000 00000000'00000001 fffff800'026c3c9b: 0x1

  STACK_COMMAND: .thread 0xfffffa80078fa040; Ko

  FOLLOWUP_IP:
  NT + 5cc7f
  fffff800'026bfc7f 488d8c2400010000 lea rcx, [rsp + 100 h]

  SYMBOL_STACK_INDEX: 0

  SYMBOL_NAME: nt + 5cc7f

  FOLLOWUP_NAME: MachineOwner

  Nom_image: ntoskrnl.exe

  BUCKET_ID: WRONG_SYMBOLS

  Follow-up: MachineOwner
  ---------

  0: kd >! findthebuild
  FindTheBuild service not found
  0: kd >! findthebuild s; .reload
  Use:! findthebuild [e |-Y] [PEI | s |-r] [-l

  ]
  -E - disables exepath update
  Y - disables friendly update
  -l - hide local sets for the railways (must be last).
  ' *' define first sympath hiding in the local cache.
  Pei - adds sympath and exepath discovery railroads
  -r - sets of paths like sympath and exepath discovery
  s - adds sympath and exepath discovery railroads
  -t--detects the code paths for this trial version
  *********************************************************************
  * Symbols cannot be loaded because the path is not initialized. *
  *                                                                   *
  * The symbol path can be defined: *.
  * using the _NT_SYMBOL_PATH environment variable.                 *
  * with the help of the there when you start the debugger argument. *.
  * using the .sympath and .sympath + *.
  *********************************************************************
  0: kd > lmvm nt
  start end module name
  fffff800 ' 02663000 fffff800' 02b7b000 nt T (no symbol)
  Loaded symbol image file: ntoskrnl.exe
  Image path: \SystemRoot\system32\ntoskrnl.exe
  Image name: ntoskrnl.exe
  Timestamp: Fri Apr 10 21:58:39 2009 (49E0237F)
  CheckSum: 00487B 94
  ImageSize: 00518000
  Translations: 0000.04b0 0000.04e4 0409.04b0 0409.04e4

  Any help would be greatly appreciated.  Thank you for your time.

  Hello

  It's a bad driver more likely. Have you added all the other new features or updated drivers just before that
  has started? Look in the Windows updates too to see if new drivers have been added at this time there. Use the utility
  below to read the minidump.

  Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
  Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
  codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
  information on all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

  You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
  system installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -----------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
  smile, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------------------
  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  ------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Windows Vista SP2, random BSOD with error checking code 0 x 19

  Hi all

  I have seemingly random crashes on my old laptop 3 years recently - BSOD with error checking code 0 x 0000019 (0x00000020, 0xe92f4780, 0xe92f48d0, 0x0a2a0440), and BlueScreenView says that accidents are caused by ntkrnlpa.exe and Ntfs.sys. I have absolutely no idea why it happened--unusual does update, none of the material changes & software installations. The system hangs especially after maybe one or two days after starting with some sleep & wake ups inbetween and the only accidents while there are prominent running shows - namely, all the accidents that happened while I was running Firefox. Seconds before the BSoD (shell & all) system simply freezes and does not respond to ctrl + alt + delete, but is still running (as indicated by the fact that once, I forced a power off and after that restart the event log indicates the previous stop at was not planned), then watch the usual BSoD screen.

  After doing some googling, I began to suspect that this should be a memory or a hard drive problem, or maybe an overheating causing the two since he not there no significant change of software on my computer recently again issues just appeared without reason. So I cleaned my laptop fan and the heatsink and ensured that the hot air can leave the chassis without being blocked, did some checking of memory with memory auditing Windows - no problems in 5 innings and ran chkdsk on my system partition with all available options - perfectly normal, but the chkdsk has acted quite strangely that check all took about 30 seconds and no normal as the ID information of partition, size etc. that should be there never appeared; is this a normal behavior? or something is wrong with my chkdsk?

  I'm still (lol) impatiently waiting for the next crash, not sure whether the problem is still there or not. Meanwhile could you please help me understand what is the problem with my system?

  It seems that the disc is the most likely cause. If it is intermittent, it may be difficult to diagnose.

  The manufacturer of the laptop provides any diagnosis?  Several manufacturers have a key at startup to access the diagnostics.

  CHKDSK should last several minutes. There is information about the different ways to run chkdsk here:

  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  You can try this disc test program:

  http://www.Seagate.com/www/en-us/support/downloads/SeaTools/

  If the version of WIndows does not find anything. Try to use the version BACK from a CD.

• Example: Pavilion dv6: after starting the laptop it is showing a request for sgm.exe error crash

  My computer starts up and I am able to work on it, but showing the sgm.exe error

  Hello

  Thanks for posting in the Forum from HP Support.

  The error occurs because there is a problem with this application.

  I did some research and I am unable to find such a program with this name that is popular and reputable.

  Having said that, I also found some virus/malware that uses this name.

  Search your computer for threats/viruses using these free tools:

  -> ESET Online Scanner

  http://support.eset.com/kb2921/?locale=EN_US & viewlocale = en_US

  http://www.eset.com/int/home/products/online-scanner/

  -> HitmanPro

  http://www.SurfRight.nl/en/hitmanpro

  http://www.SurfRight.nl/en/downloads/

  -> AdwCleaner

  http://www.bleepingcomputer.com/download/adwcleaner/

  If these tools find a malware with this name and extension, remove and others, also.

  Please, let me know the results of the analysis.  You can also provide screenshots if you want

  http://www.take-a-screenshot.org/

• Pavilion g6: BSOD BUGCODE_USB_DRIVER error

  I have a HP Pavilion g6-1b60us running Windows 7.  Recently, I've been doing the BSOD with error code BUGCODE_USB_DRIVER at least once a day, sometimes several times a day. I tried updating the drivers, but am still affected by the same problem. Your help would be greatly appreciated!

  Hi there @reCATcha1 
  
  Welcome to the Forums of HP Support! It's a good place to find the help you need, so many other users, the HP experts and other members of the support staff.

  I understand that you have found an error on blue screen BUGCODE_USB_DRIVER. I'm happy to help you.

  Have you tried to scan your system for what as malware, viruses etc?  If you do not I would recommend doing this first and as a result, clean your system.

  If you know approximately when the problem started, you can try to do a system restore to a point before it all started.

  Using Microsoft System Restore (Windows 7)

  Otherwise, I recommend you back up the contents of your hard drive and then look at the system recovery, I would start with just the drivers, and if it does not help, then a factory restore.

  Performing a recovery of system HP (Windows 7)
  Troubleshooting problems of recovery HP System (Windows 7)

• AccelerometerSt.exe error on the computer Windows 10 brand new

  I have the same problem that many others have with the Application AccelerometerSt.exe error.   BUT, I have a brand new - 1 week old computer and it came with 10 windows already on it.  I have the HP Envy x 360.   How do you intend that to solve the problem.   If you uninstall and reinstall Windows 10, I'll need much more detailed information.   I don't know how to do this - which was the reason why I only watched computers with her already preinstalled.

  Hello

  Try the following.

  Open windows control panel, open programs and features, make a right click the entry for HP 3D DriveGuard and select uninstall.

  When this has completed, restart the laptop.

  When windows has reloaded, download and install the version of DriveGuard on the following link.

  http://ftp.HP.com/pub/SoftPaq/sp67001-67500/sp67280.exe

  Kind regards

  DP - K

• Explorer.exe error

  Hello

  I have HP Pavilion e002au laptop bought about 5 months back with Windows 8.

  I get the explorer.exe error after logging in each time. The laptop seems to work normally, but can someone please tell me what this error is and how it can be eliminated?

  I have an original version of Windows antivirus updates and get regularly.

  Is it dangerous for the laptop?

  Kind regards

  Vikram P. Gupte

  Hi Vikram6880,

  During the execution of any type of control system, you should always back up your documents. The update affects all documents. It was simply an update of the system.

  Thank you.

• nidevmon.exe error 0xc0000142 / niusb6009 multifunction i/o

  Our Labview application collects analog data using an e/s of the Multifuncion niusb6009. The application is proven and has been in production for years.

  Today, the application has stopped to receive analog data. After the termination of the application, shut down our computer w / Windows XP Pro SP2.

  The computer and Windows has restarted. At the opening of our LabView Application, the following error appears:

  nidevmon.exe error: "the Application failed to initialize properly (0xc0000142) click OK to terminate the application.»

  Scuba Steve Howdy!

  Is there something that could have been changed software/hardware-wise on the machine before this error occurring?  Also, what version of LabVIEW and DAQmx do you use?

  This could be caused by a number of different things of nidevmon.exe.  Please look over this article in the knowledge base for possible solutions to the problem.

  Kind regards

• mscorsvw.exe error

  While my pc was going through updates to MS, he projected blue.  After the reboot, I now get mscorsvw.exe error

  Hi frank platt,.

  What the full error messages you found?

  After return from error messages full so that we can help you better.
   
  I suggest you to reset the Windows Update components. Then try to install an update at a time and checking update problem. After return to status so that we can help you better.

  To reset the Windows Update components visit the link below and click on solve this button / follow the given steps to repair it yourself.
  http://support.Microsoft.com/kb/971058

  Hope this information is useful.
   
  Umesh P - Microsoft Support

• I can't install WGAPluginInstall.exe error 0 x 80070003 help

  HI the FRIENDS MY SYSTEM IS SICK, I CAN NOT INSTALL WGAPluginInstall.exe ERROR IS 0 x 80070003 I CAN'T DOWNLOAD ANY FILE WITH DOWNLOAD MANAGER (CONNECTION WITH the SERVER IS LOST) I CAN'T OPEN the DOWNLOAD of PAGES WEB BROWSER VIEW WITH BROWSER WEB MY ANTI VIRUS IS up to DATE I am not CONFUSING WHAT IS THE PROBLEM

  Amin,

  Remove the download directory and then to return to the update sites. to do this, follow these steps:

  1. stop the automatic updates service. to do this, follow these steps:

  a. Click Start, click Run, typeservices.mscand then click ok.

  b. Automatic Updates service right click and then click on stop.

  c. minimize the software component services snap-in.

  2. rename the c:\Windows\SoftwareDistribution directory. to do this, follow these steps:

  a. Click Start, click Run, typecmdand then click ok.

  b. type cd %windir%, and then press ENTER.

  c. type ren C:\Windows\SoftwareDistribution SDTemp, and then press enter

  d. type exitand press ENTER.

  Note when you delete the folder % windir%\softwaredistribution, the history list is erased from the section "review updates" site web windows update. This action will not affect the updates installed on your computer. subsequent updates will appear in the history list.

  3. start the automatic updates service. to do this, follow these steps:

  a. expand the component services snap-in.

  b. right click on updates service automatic and then click Start.

  c. close the window of the software component services snap-in.

  4. visit the website of windows update, the microsoft update web site or the server wsus again and then download an update.

  5. If you still receive the same mistakes, make sure you have correctly completed steps 1-3.

  6. If you can't always install the update, see the following microsoft knowledge base:

  http://support.Microsoft.com/kb/906602/ installation problems troubleshooting windows update, microsoft update and windows server update

• Daemonu.exe error turns off my computer. How do fix?

  Often, I get an error message after my computer shuts down-Daemonu.exe error.  Is there something to fix this problem?  Thank you.

  Hello

  It's the Nvidia Update Manager, so you must check with their Support and Forums.
  Would be a good idea to update the driver or re - install the last longer if not recent exists.

  NVIDIA - drivers - use OPTION 1 to manually enter your info driver to get the most recent drivers.
  http://www.nvidia.com/download/index.aspx?lang=en-us

  NVIDIA Support - check with the support that she might be a known issue
  http://www.nvidia.com/page/support.html

  NVIDIA forums - also check for the forums it might be a known issue or others likely to have
  http://forums.nvidia.com/

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• In Windows Server 2003, I got the following error "svchost.exe - error on line 392."

  In Windows Server 2003, I got the following error "svchost.exe - error on line 392."

  Kindly help.

  Hi Sophie,.

  Your Windows Server 2003 issue is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Windows Server forum. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• application spoolsv.exe error.

  I have windows xp and I get the application spoolsv.exe error. It gives me the following message is displayed: the Instruction at 0x01fb0374 referenced memory at 0x1fed12c0 memory cannot be read. "I don't know what to do about this.  Help, please.  * E-mail address is removed from the privacy *

  Hello

  1 did you change on your computer?

  2. what service pack is installed on your computer?

  3. when exactly did you receive this error message?

  4. What is the brand and the number of the printer model do you use?

  Method 1:

  I suggest you try the steps suggested by Anthony - Support Engineer from the below mentioned link and check if it helps. These steps are for Windows Vista and should work as well on Windows XP.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_other-windows_update/spoolsvexe-application-error/0a7b0b15-77b3-4a8f-9465-dff8517c226e

  Method 2:

  You cannot print and you receive the error message "Spooler subsystem app has encountered a problem and needs to close."

  http://support.Microsoft.com/kb/810894

  To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information on how to to back up and restore the registry,

  Method 3:

  I also suggest you to follow the link and check.

  Resources for the resolution of the printer in Windows XP problems

  http://support.Microsoft.com/kb/308028

  See also:

  How to cancel printing or to delete a print job that is stuck in the print queue in Windows XP

  http://support.Microsoft.com/GP/pc_print_methoddstoptheprin

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• nipalsm.exe error

  I currently have LabVIEW 2009 installed and NiDAQ 9.0.1. I am trying to connect to cDAQ 9174, with the NI9401 and NI9263 modules. When you connect the cDAQ, that an error occurs:

  nipalsm.exe error

  The instruction at 0x6efdfde3 referenced memory at 0 x 00000034, the memory could not be 'read '.

  The cDAQ appears in the list of devices, but fails self-tests and nor modules are recognized. Also the cDAQ access to the list of devices cannot deleted even before the device is connected.

  I tried to use the program to software installation OR repair NIMAX and tried to uninstall and reinstall absolutely everything. (even on the complete reinstall the cDAQ device seems not connected on the list of the devices before connecting for the first time)

  have you seen this

• trl120.bpl/Setup.exe error updating panda internet from 2011 to 2012

  Tried to update my panda internet between t0 and 2011 2012 and I sysytem mechanic.now I have the app missing rtl120.bpl and he says panda has stopped working I tried to re - install panda from the disc, gets most of the setup.exe error then made way. Thanks for reading. (email removed for privacy)

  Hello

  I would like to do you right click on the file setup.exe and run as administrator.

  If this is little help, contact the manufacturer to better aid.