CUCM 8.6 MOH Volume question

Similar Questions

• Several replays on a Volume - Question

  Until recently I had 1 daily Replay on each Volume, was taken at midnight and which expired 48 hours later. It seemed to work well for progress data.

  Now, I had added 1 hour Replays to all volumes that are taken every hour and expire every 90 Minutes. This is for our data replication.

  Progress of the data still work properly? Since my daily replays cut a good deal now obviously because Active reading is certainly not as complete as he drained the time previously of the Raoul.

  If I'm confused?

  Yes, it will be.

  Data in one of expired Replays which has been removed from the server or not necessary to restore from another Replay will be delivered in the pool of free space. Data that is always on the server or for a rerun will be just unite in the replay that requires the data bits or the old Replay (you will see as it is usually the biggest).

  When you take a replay anything whatsoever to the assets becomes an integral part of the final proofreading and resets active at 0 until the next block is written.

• BlackBerry Bold 9650 smartphone volume questions in the case

  I used my Bold 9650 in the Holster while I work in the gym and I was listening to Pandora. I noticed that the volume controls on the right side of the device will not work while the unit is in the Holster. If I get out of the Holster, the volume buttons work fine. Is it possible to allow these buttons while the case is used? I would have thought that they would work automatically by default. Thank you.

  I'm no expert on the cases, but I know that the magnet in the case puts your phone "sleep", turn off the screen.  This could also affect the side buttons.

  To make sure that this isn't just a problem with your phone, remove your battery when your phone is turned on, then replace it.  If the symptoms persist, it could be something with that you'll just have to live.

  I hope that helps you.

• See questions about the Satellite A205-S5859

  I would like to know the following:

  1. is there a problem with the speakers of this first use. The volume deteriorates. You will need to set to 100.

  2. can I put the car in a dedicated video video?

  3. What is the maximum memory for this model? Where is the memory chip?

  One of my friends has a laptop A200. It s not A205 but very similar. The A205 is designed for the American market and the A200 to the European market.

  So finally, I can give you some suggestions on the issue:

  (1) any volume questions are not known for me everything works ok.

  (2) No, upgrading the graphics card is definitely not possible

  (3) I guess you'll find this info in the user manual. Did you check that?
  But I think that there is a possibility for an upgrade to 4 GB of RAM. But I do not recommend upgrading the RAM to 4 GB due to the limitation of the 32-bit operating system. All the 32-bit OS s can manage 3.2 GB RAM max.
  Finally, the position of the slots memory; I think that it s at the bottom of the unit.

  See you soon

• How to use the authentication of the URI (e-mail) of MRA - different domain through the highway-C

  Hello

  I am not able to connect to the MRA using my E-mail address. How to solve it?

  My account is [email protected] / * / (this is my domain name locally, not resolved on the internet)

  My email (URI) is [email protected] / * /

  If I connect to internet using my ID of combined directory with my external internetresolvabledomain.com, IE [email protected] / * /, then she succeed.

  But if I use my e-mail address, it cannot be authenticated because the highway to remove the domain, and then ask the CUCM for validation.

  Question: How will I know the Expressway-C that this area is an e-mail address (URI) of my iantra123 account?

  And, said the Expressway-C do not delete this domain for authentication?

  Kind regards

  Antra

  OK, on ARM, when he uses NODES to search for the user in your CUCM, it won't work if you use the IADB, if you use e-mail, it will return a not found message, you can see that the EXP - C opens a session.

• HP Pavilion 15-P030TX (Volume / Audio Swing/leveling question) (Realtek High definition Audio) (BeatsAudio)

  Laptop HP Pavilion 15 - P030TX (Windows 8.1) (running Realtek High Definition Audio) (BeatsAudio) driver 6.0.1.7272

  Product number: J2C69PA #UUF

  -I got her number through which the music volume up tremedously and lower down when the bass get (even though I disabled the beatsaudio the problem is still there).

  -the problem occurs when you use headphones and speakers for laptop.

  -Are there in any case to fix... Help... AS SOON AS POSSIBLE

  Hi great-tree Deku,

  Thanks for helping me with this regard, after many trials, I finally found a driver that is very good for my pc for now.

  Here is the link to the driver:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=CP-132040-1 & CC = US & DLC = in & LC =

  Realtek HD Audio Driver

  version 6.0.1.7135 Rev B

  So far my experience with this version of the driver is quite ok, 5 bars work and the question of swing volume disappeared... but there is only one problem with this driver by which song / midtones / highs are higher, even with the default settings, which makes the audio less complete and the net resulting in less comfortable to listen... I tried to set the EQUALIZER, but she out of her just like hiding the harmony of the sound with the bass... but I'm fine with it now... If all goes well, there will be a more tuned up to the version of the driver after that... =)

  It's my settings of 5 bars

  Bass 77 / 76 equal focus 45 55 40 15 central space (just in case someone else) =)

  Once again, thank you. =)

• question about volume license cd and retail key__

  I am in the process of a computer repair (bad mem and corrupted os). The xp operating system installation cd only I have is for a volume license. As I intend to sell or donate a computer, for obvious reasons, I don't want to put the volume license key in the public domain. The former owner has the disc with a touch of detail record but lost the cd.

  The question is can I use the cd volume and use the retail key?

  NO.

• Question regd import/export feature of CUCM BAT

  Hello

  We have a production cluster CUCM 8.6 running.

  I was asked to create models of translation of 300-400.

  I see that I can not do this directly through bat. But I can't see the import/export option.

  We have 1000's of existing patterns of translation on our system.

  I have a small question about the import feature.

  A new import overwrites existing data in the database that contains the data in the import file or because the new data in the import file added to the existing data.

  If the import file has only the new models of translation, it will eliminate the existing patterns of translation in the system?

  I don't have a system of cucm lab to verify this behavior?

  Can you please help me on this query?

  Thank you

  Pete

  I often do and it's the only way to bulk add translation models. It removes all the reasons for translation it will only add/edit the translation model. If all the new models it will simply add your new entries.

• Outgoing Caller ID question using CUCM 8.6, MGCP gateway & PRI lines

  Hello

  We have two ranges DID with our provider: 02825911XX & 02829212XX

  02825911XX maps extension 11XX

  02829212XX 12XX expansion cards.

  We have 2 E1 lines 60 channels.

  Current configuration:

  CUCM <----MGCP---->Gateway (8.6.2) (2921) <======2 e1="====">carrier / Teleco.

  Question:

  When calling 11XX we get correct caller id 02825911XX.

  But when the 12XX we receive caller ID 02825911XX instead of 02829212XX.

  for example: when calling 1206 far end caller id watch 0282591106 instead of 0282921206.

  No problem in incoming calls on the two beaches.

  The external mask are configured correctly in the domain name.

  The debug ISDN q931 shows the correct caller until the gateway ID:

  ISDN Se0/0/0:15 Q931: TX-> INSTALLATION pd = callref 8 = 0x016A
  Complete package
  Carrying capacity I = 0x8090A3
  Standard = CCITT
  Ability to transfer = speech
  Circuit transfer mode
  Transfer rate = 64 kbit/s
  The channel ID I have = 0xA98396
  Exclusive, Channel 22
  Display i = 'test '.
  Calling party number i = 0 x 0081, '0282921206'
  Plan: Unknown Type: unknown
  Called number i = 0 x 80, '82353587'
  Plan: Unknown Type: unknown

  Fixing ccapi inout & ISDN q931 debug. & Gateway config.

  Hello Gyanendra,

  I checked the configuration debug and gateway.

  These debugging come from gateway. The catwalk shows TX - Setup. Once we have sent installation information to the telephone company, I don't think that we can change the ID calls information. This means that we send correct calling Telco part number information (0282921206).

  May be that Telco is changing the number on their own party? Have you checked with Telco yet? If not, ask them what is the number of parties calling they get. You can do a live test and track same call with the telephone company engineer.

  The details of trace log:

  00:49:25.410 Sep 10: ISDN Se0/0/0:15 Q931: TX-> INSTALLATION pd = callref 8 = 0x016A
  Complete package
  Carrying capacity I = 0x8090A3
  Standard = CCITT
  Ability to transfer = speech
  Circuit transfer mode
  Transfer rate = 64 kbit/s
  The channel ID I have = 0xA98396
  Exclusive, Channel 22
  Display = 'Ludvík Aunedi' i
  Calling party number i = 0 x 0081, '0282921206'
  Plan: Unknown Type: unknown
  Called number i = 0 x 80, '82353587'
  Plan: Unknown Type: unknown
  00:49:26.222 Sep 10: ISDN Se0/0/0:15 Q931: RX<- call_proc="" pd="8"  callref="0x816A ">
  The channel ID I have = 0xA98396
  Exclusive, Channel 22
  00:49:26.222 Sep 10: ISDN Se0/0/0:15 Q931: RX<- alerting="" pd="8"  callref="0x816A">
  Sep 10 00:49:26.258: / / 6444, 9E3008C18C96, CCAPI, ccCallModifyExtended:
  Numerator = 0x2B305B60, Params = 0x2B304D78, Id = 6444 Call
  Sep 10 00:49:26.258: / / 6445, 9E3008C18C96, CCAPI, ccCallModify:
  Numerator = 0x18E30, Params = 0x2B304F80, Id = 6445 Call
  Sep 10 00:49:26.258: / / 6444, 9E3008C18C96, CCAPI, cc_api_call_modify_done:
  Result = 0, = 0x2AF52C6C, Id = 6444 Call Interface
  Sep 10 00:49:26.262: / / 6445, 9E3008C18C96, CCAPI, cc_api_call_modify_done:
  Result = 0, = 0x2AD55F80, Id = 6445 Call Interface
  Sep 10 00:49:29.406: / / 6444, 9E3008C18C96, CCAPI, cc_handle_inter_digit_timer:
  Generate inter-chiffre timeout CC_EV_CALL_DIGIT_END event
  00:49:35.262 Sep 10: ISDN Se0/0/0:15 Q931: RX<- connect="" pd="8"  callref="0x816A">
  00:49:35.266 Sep 10: ISDN Se0/0/0:15 Q931: TX-> the CONNECT_ACK pd = callref 8 = 0x016A
   
  Also, can you do another test call and join:
  Debug mgcp packet with debug ISDN q931 and CCAPI inout
   
   
  Kind regards
  Amarjeet
   

• BlackBerry Smartphones has simple question on volume of phone ringing.

  I am grateful for this forum because even simple questions like the following are difficult to obtain responded by Blackberry.  Seizing the issue in the 'Help' section on my handheld gives always nothing.  It seems that a large company like RIM would understand more in their user manuals.  Anyway, enough ranting... Here's the question:

  Quite simply, how can I increase the volume of the ringer on the phone?  By pushing the volume button for a call that increase the volume of calls.  Pushing not courts of appeal does nothing.  I'm sure that there is a way to do it, but I'm coming emptyhanded.

  Thank once again the community here as a whole for the excellent work which is made to help other Blackberry users.

  Profiles > advanced > highlight the profile you want to edit > press the menu key and go to 'Edit' > scroll down the list and find what you want to change the volume of the ring tone for example, standard messages

• Question about commissioning of the E20s - CUCM and TMS

  If we now run software CUCM 8.6.2 and 4.1 E20.  I played with CUCM and TMS supply by and a few questions.

  It seems that there are some features that can be set via the TMS models that cannot be resolved via CUCM (MTU, custom, etc commands).  Is it possible to apply these settings through TMS while having the unit registered in CUCM?

  Essentially, I want my call recording platform CUCM and control, but want to keep the granularity that TMS offers in terms of commissioning etc..  I expect the same problems with C-series, etc.

  Am I right in saying that, in order to get the E20 to join CUCM, I need to define the external Manager to "CUCM", and thus eliminate any possibility of TMS to manage? Otherwise, what is I could have managed by TMS and then set the SIP of the E20 to point to CUCM via templates in TMS?

  Any tips on that?

  Hello

  Having both TMS and CUCM to manage endpoints is not a good idea (yet). TMS and CUCM will return to each of the other toes with unpredictable results.

  With TMS 13.2, I understand that you should be able to import the CUCM in TMS and then find all systems registered to it and import these into TMS, however in this case TMS plan only systems conferences and will manage them not active (you can see status of the call as well).  13.2 TMS is not yet released, so that's what I said must be in this version.

  So basically now if you use CUCM, use CUCM provisioning and don't use TMS.  We focus on interactions with systems registered with CUCM TMS and it will be more developed on this in the future.  I recommend you check out the TMS13.2 release notes released to see if it is mentioned.

  Thank you

• In order to become a distributor of volume Adobe Reader, (my computers have no internet access), I need to fill out the Distribution of Volume License Agreement, but will not accept an answer I gave to the question: "Please indicate the product or service

  In order to become a distributor of volume Adobe Reader, (my computers have no internet access), I need to fill out the Distribution of Volume License Agreement, but will not accept an answer I gave to the question: "Please indicate the product or service name and description.

  This form must be completed and submitted online. Also the browser Javascript must be activated.

  https://distribute.Adobe.com/mmForm/index.cfm?name=distribution_form&PV=RDR

• Volume of the speaker in X 40 question

  Dear Forum

  I have a question about my X 40. When I use it it is a built-in speaker and you can adjust the volume as much as possible to the maximum.

  However, I noticed that when the ultrabay docking station is used with the laptop, can reach a much higher sound volume when the laptop is used without the ultrbay docking station.

  Please anyone know why this is? Is it because there is another stakeholder in the docking station

  If someone can advise, I would be grateful.

  With best wishes

  Ian

  The answer is because the X 40 has himself a speaker built-in. Features detailed - ThinkPad X 40

  The X 4 What ban has two built-in stereo speakers.  Docking ban ThinkPad X 4 - Overview

  Hope this helps

• the logical volume change question

  Hi all

  I'm a bit rusty...

  On an audio track, I would like to take a little bit of audio in the middle of a track - drag from left to right - pointing out a few bars and when I let go automatic volume benchmarks would start at the end.

  Then, I would just be able to click inside the selection and do increase or decrease the volume for this section.

  I forgot the tools to do this easily

  Can anyone remind me how to do this?

  Hello

  With the automation of volume showing track, use the marquee tool to "slide". Click and drag the volume automation curve to adjust as you describe

  TDC

• Question about volume adjust the volume knob - Satellite Pro U300

  Hello

  I have a problem with the volume control. When I adjust the volume using the button on the left side of the laptop, I can only choose 3 levels of "loudness":

  No volume, very quiet volume and maximum volume (from rabies).

  Is this normal, is not anyone have problems with this?
  I hope that the problem is because of the digital volume adjustment screw. The adjuster does not record the exact position of the volume button. Every time when I get a phone call at work (I listen to internet radio), I turn off the radio by using the adjustment screw on the side of the laptop. When I end the phone call, I always need to open the laptop and the volume on the windows task bar, because when I use the device volume control on the left side of the laptop, it will just immediately at maximum volume.

  Welcome them

  Hello

  It s very strange that your volume control contains only 3 levels of volume
  I noticed that Toshiba has released a new driver (v. 6.0.1.5473) sound on the European driver page.

  How about if the update driver sound?
  Audio driver certainly controls the volume sound and in my opinion it s worth a try.

  Good luck