CUE Telnet access

Similar Questions

• Telnet access

  Greetings,

  I test on the lines of the telnet access lists and I'm having a bit of a problem. I applied a router access list 'a' and applied it to the line vty 0 4. This access list restricts telnet access to one switch, another router 'b' and many portable computers. Laptops can get in OK if they go directly to the router 'a', however, is they connect first to router 'b' and then try to telnet to router 'b', they get the message "access denied on router" a"even if the ip of the router's Ethernet interface"b"are both.

  explicitly permitted in the access list, as well as the ip addresses of the laptops. There are no instructions 'decline' in the access list, except the statement implicitly denied at the end.

  Router 'a' and 'b' is connected with each other through subinterfaces on serial ports with the frame relay connections.

  Any ideas why the laptops cannot telnet sessions to the router "b"?

  Any ideas?

  Thank you

  Dallas

  I think you have the wrong IP address for router B in A access list. It could also be a vs problem generic mask subnet mask.

  First thing to check: what IP address router did see you telnet in with router B?

  I'll assume the standard of access list number you use is 1. (It can be anything, 1-99, or it may be a named access list. "I'll use 1 here.)

  The router has, under 'line vty 0 4', remove the command "access-class 1 in. Then, log in to the router A to router B. On router A, run "users to see the" to see the address IP think you just. It is the address (or subnet, depending on how you hide) that you need in your order of "license to access-list 1.

  If both routers are on different LANs with different subnets, but are connected by serial link, then the IP address on the interface closest to the router has that B will use to initiate the telnet session. And the closest interface would be the subinterface series you mentioned.

  You said you used the Ethernet interface IP addresses. They would work if both routers are on the same LAN or subnet. or they would work if the LAN interfaces were along the route of the road between the two devices, the LAN interfaces have been on different subnets. In case you have several connections between two routers, whatever the you telnet to East the subnet and interface on that your turns off session IP address.

  Second thing to check: you have a good command of "license to access-list 1? Look for the address or the subnet that you saw above. Sometimes, the address is correct, but the problem is with the which is the reverse of the subnet mask.

  For example, specify a static route to a specific host would address 10.1.2.3 and subnet mask 255.255.255.255. in an access list, allowing a specific host would use address 10.1.2.3 and mask with joker 0.0.0.0.

  In the case of a subnet, if you want to specify a static route to the 10.1.0.0 with a 16-bit subnet mask, you must use the subnet mask 255.255.0.0. The mask of generic access list for the same subnet would be 0.0.255.255.

  And in the case of a point type subnet point-to-point minimalist on a subinterface series WAN link, if you want to allow access to the 'whole' in a single command subnet, let's say your subnet was 10.168.212.4 with a 30-bit subnet mask (if you have sous-reseau.4 IDS, two addresses to IP et.6 and IP address of subnet diffusion.7 utilisables.5) your subnet mask 255.255.255.252 while your mask with joker would be 0.0.0.3.

  See the model? First octet of the subnet, added to the first byte of the generic mask, mask is 255. Ditto for the second, third, and fourth bytes. If not, then something is wrong — double check your numbers.

  Last thing to do: put in the "access-list 1 permit 10.168.212.4 0.0.0.3" command on A router (or any address/wildcard combination you need for router B) and add the command "access-class 1 in" back to your 'line vty 0 4 '. Try your telnet to router B to router A. It should work.

  I hope this helps.

• Unauthorized telnet access

  Hello

  If someone could guide in writing script of EEM to allow users to access based on the IP address telnet session...

  Or send by email whenever someone telnets to the device.

  Kind regards

  Faizan.

  If you want to restrict access by IP telnet, use a list of access and access-class on the VTY lines.  EEM can help.

  You can have the EEM react to messages provided you have 'connection-success journal' configured logon.  It would be:

  Event Manager applet telnet-login

  syslog event model "port of connection Success.*local: 23.

  Our mail action 1.0 from [email protected] / * / to [email protected] / * / subject to body of server 10.1.1.1 "Telnet Login" "user just telneted to the device.

• SSH and Telnet access for catalyst 4503 list

  I was wondering the structure of command to apply an access list to ssh and telnet on a catalyst 4503. I keep a list of access for indoors and outdoors. Can afford two different IPs from the outside? Thank you

  You will need create an access list indicating the networks/hosts that you want to allow.

  -Example

  access-list 10 permit 10.10.1.10

  access-list 10 permit 10.10.2.10

  access-list 10 permit 127.1.0.0 0.0.255.255

  access-list 10 permit 192.168.1.0 0.0.0.255

  So you want to put this list of access on the VTY interfaces.

  -Example

  line vty 0 4

  access-class 10

  entry ssh transport * if you only want to SSH *.

  line vty 5 15

  access-class 10

  entry ssh transport * Ditto *.

  Now you can do all this with * line vty 0 15 * but, it gives you a better idea of what is happening. It is a simplistic configuration. Remember that it is advisable not to allow ssh. If you want to allow at the same time, let him * transport input ssh * out of the configuration.

  I hope that gives you an idea of the structure. If this is not the case, let me know.

• 2911 ISM and CUE: need to (re) install CUE to access GUI?

  All the experts out there, I am a volunteer for installation of the IPT (voice) for my church.  They have a 2911ISR router that I'm trying to install / set up for a small Office Setup.

  The question is stated: need to (re) install CUE to get the GUI (web Interface) to work?  It comes with CUE 8.6.6 on module ISM-SRE-300-K9.  But I don't know if it's because the GUI isn't here or if I have configured the interfaces and route incorrectly.

  Here is the list of software on the ISM:

  MACC-2911-CUE # sh inst soft its
  History of Software Installation:
  See install.log for more details

  2014-03-19 12:48:39 * Install Publ. command * cmd: Opt 1: 0, Pkg:cue - allapps.sme.8.6.6.pkg Url:ftp://10.1.1.1// Mode: 1 Proto:1 host: 10.1.1.1
  2014-03-19 12:56:41 * CLEANED SOFTWARE *.
  Timestamp subsystem Version Description UID
  2014-03-19 12:56:42 Thirdparty 8.6.6 Service motor Thirdparty Code a3442277-7890-4782-9e6b-9d19efc1e0d8
  2014-03-19 12:56:42 plugin Enablement 8.6.6 enablement Plugin pack 26bd663c-3e5a-43d9-a6c3-5441ce44941b
  2014-03-19 12:56:42 languages of linguistic support for voicemail 8.6.6 IDENTIFIES global pack e2e81cc6-39b5-47e1-9f83-b83c897fc50c
  2014-03-19 12:56:42 overall 8.6.6 Global manifest edceaf0b-a890-4045-9086-5452fac85eba
  2014-03-19 12:56:42 infrastructure 8.6.6 Service engine Infrastructure a36e1be1-ce8a-4f53-ace7-1844262aa0b9
  2014-03-19 12:56:42 LPG Infrastructure 8.6.6 Service engine LPG Infrastructure 9f112eb1-6f58-4dd4-8faa-8530467af3b9
  2014-03-19 12:56:42 Voice Mail 8.6.6 Voicemail application 8e7823e2-0e92-4470-8860-653246345f9d
  2014-03-19 12:56:42 CUE Voicemail UK English 8.6.6 British English language pack fa803d25-9c89-4171-a14c-ec12d6ed6b8c
  2014-03-19 12:56:42 Bootloader 2.1.36 (secondary) Service Engine Bootloader 9d7b26fb-21b2-416e-8b65-425c2f8da5d8
  2014-03-19 12:56:42 8.6.6 installer Installer a0fb9f0a-fa5c-4b21-a64c-0cb9d6379573
  2014-03-19 12:56:42 core 8.6.6 engine OS Core Service 430f25f9-0fed-48a4-b362-823937138501
  2014-03-19 12:56:42 standard automatic Telephony Service Infrastructure 8.6.6 engine e3db91b0-f47d-460c-ad22-65001a5d45a9
  2014-03-19 13:01:48 * CLEANED SOFTWARE *.
  Timestamp subsystem Version Description UID
  2014-03-19 13:06:40 * CLEANED SOFTWARE *.
  Timestamp subsystem Version Description UID
  2014-03-19 23:17:44 * CLEANED SOFTWARE *.
  Timestamp subsystem Version Description UID
  2014-03-19 23:41:53 * CLEANED SOFTWARE *.
  Timestamp subsystem Version Description UID
  2014-04-20 17:47:59 * CLEANED SOFTWARE *.
  Timestamp subsystem Version Description UID
  See install.log for more details

  Can you confirm the GUI files are there or they lack; in which case I need to (re) install CUE?

  Thanks in advance for any help you can provide.  It is greatly appreciated.

  Shutdown?

• can I use aaa for telnet access to a pix?

  It's a 6.2 (2) the 506e running. I have all my routers and switches use Ganymede authentication. is it possible on with the pix? useful links or instructions?

  Thank you

  YES, you can control access to pix via Ganymede or any aaa server. Here is the link perfact explaining config etc for

  http://www.Cisco.com/warp/customer/110/authtopix.shtml

• Configuration of the ACL to restrict access via SSH/Telnet

  You want to shoot a SSH/Telnet access to ISP address/IP of my switch interface.  Since the Dells have no strict vty/con interface to apply an ACL I guess I just have to match on an interface instead.  Using the ACL below.  Problem is that applying it kills telnet/ssh sessions completely and does them in.  Replaced the iPs in the wrong example with IPs.  Confirm that my public IP address is 112.94.236.58.  You will see a 112.94.236.56/29 with a permit instruction.

  TEST from the list of access permitted tcp 111.126.50.0 255.255.255.0 111.126.50.16 255.255.255.0 eq 22

  TEST from the list of access permitted tcp 111.126.50.0 255.255.255.0 111.126.50.16 255.255.255.0 eq telnet

  TEST tcp allowed access list 112.94.236.56 255.255.255.248 111.126.50.16 255.255.255.0 eq 22

  TEST the access permitted tcp 112.94.236.56 list 255.255.255.248 111.126.50.16 255.255.255.0 eq telnet

  TEST from the list of access permitted tcp 112.94.254.0 255.255.255.128 111.126.50.16 255.255.255.0 eq 22

  TEST from the list of access permitted tcp 112.94.254.0 255.255.255.128 111.126.50.16 255.255.255.0 eq telnet

  TEST the access permitted tcp 112.94.248.176 list 255.255.255.248 111.126.50.16 255.255.255.0 eq 22

  TEST the access permitted tcp 112.94.248.176 list 255.255.255.248 111.126.50.16 255.255.255.0 eq telnet

  access list tcp TEST refuse any 111.126.50.16 255.255.255.0 eq 22

  access list tcp TEST refuse any 111.126.50.16 255.255.255.0 eq telnet

  TEST the ip access list allow a whole

  111.126.50.16 is the switch

  Maybe I should use a destination host in the ACL instead?  (edit, nope, tried with a subnet of 255 s all, same problem)

  The ACL is created using the command access-list config mode.  On the interface it won't let me use ip access-class.

  Figured it out.  Kept, see references to "MACL", think why I needed a MAC access control list.

  Nope.

  Dell world, this means access control list management.

• Cannot access admin (ReadyNAS 102) Panel

  After turn on my NAS gets 192.168.2.25 IP address, I can ping from my PC. Power led blinks constantly after power to the top, I can't disable it only by unpluging power cord. I can't access Admin Panel by browser (connection refused) in Chrome and IE. I tried the procedure of resetting factory and OS reinstall that brings no improvement. RAIDar software is the realization that one SIN, but the firmware version is empty, so I guess there's the problem. Is there a way I can download the firmware - for example from USB when I have no access to admin panel? I am very disappointed because this is the State of the new product and my business really needs it goes fast...

  Hello CPR,

  Welcome to the community!

  The operating system and data are saved on the disc that is inserted in the ReadyNAS chassis. Without the records, there is no, you will not be able to access the admin page. SSH is also disabled by default, so if you want to access via SSH, you must Access the first admin page and then allow it to from there. Telnet access is designed for engineering and support of L3.

  Kind regards

• How a router via the Telnet command file

  Dear boss

  I have a few remote cisco router and have telnet access to the router (172.16.1.1, 172.16.2.1...). I want to add a route to the router through a windows batch file. How do I? Please help me with the sample.

  Thanking you

  Shahid

  Hey Shahid,

  The issue of Windows XP, you have posted is better suited for the IT Pro TechNet public. Please post your question in the

  TechNet Script Center for assistance.

  Hope the helps of information.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Firewall XP slows telnet and pop requests to other servers

  with xp firewall WE telnet takes about 10 seconds to connect to my linux server. workstation on the same POP form xp server takes about 10 seconds
  with xp firewall OFF it connects instantly
  I've tried doing the fomr even another machine winxp and this problem does NOT occur. So it seems that I have a machine that has a firewall problem
  all windows updates and patches have been installed
  This dbeen has now lasted about a year. time to find out how to fix :)

  Well, for all those interested, ive worked the definitive answer to this problem underway long myself for "xp firewall slows down applications to other telnet servers and pop.

  After doing a few capture and analysis of communication between my workstation and server, I noticed the server sending some 113 applications port to my work in response to the pop stations and requests for telnet access and I think than ftp also.

  Port 113 refers to "ident" username for authentication on the servers running of authentication such as "identd". If the workstation does not respond, then it may delay the connection. The solution is to put an exception on the firewall of my computer such as windows xp firewall to allow port 113 through.

  To do, it is very easy for all of us here are the steps for your Windows XP workstation:

  Start | Control Panel | Windows Firewall | Exceptions | Add Port. 113 TCP Port number. Comment: The authentication of the user name to the server with the ident Protocol

  So there you have it. Finally... INSTANTLY connect and response of the connection for pop, telnet and ftp :)

  Edward Jozis

• WAG320N telnet ssh

  Hello!

  you know that you can activate the ssh / telnet / rlogin into the modem / router wag320n?

  Thank you
  Walter

  It is always a consumer device. If she had telnet access some customers would use and some wouldn't have the slightest idea what they due and, but Linksys would have to provide the service to all the...

  Check out the 3rd party firmware like dd - wrt or similar. There you can do whatever you want. Of course, it is not covered by warranty.

• NAS200 telnet? fsck? Lost + found? Help me please.

  Hello world.

  I NEED to access the NAS200 drives.

  Somehow my file system was broken.

  Yesterday I was copying some files on the device (attached to a dedicated UPS, so no power failure when writing) during the copy (it was long) I tried to delete some files in a different folder.

  The player responded: removal of the files had a life (even if the copy is complete) it took about 40 seconds to delete each file...

  So I decided to cancel the operation and restart the device.

  I pressed the power button, I heard the stop sound and turns off after a while.

  I turned on it once, it happened as usually: leds (power - activity - disk1 and disk2), beeps...

  Then I tried to access my files, but vista gave me a network share could not be found.

  First of all, I ping the device, he was there.

  Then I have connected to the web management, made a successful logon, checked state.

  All right: two recognized discs. Chip Disk1: OK, chip Disk2logical disk K 0 (raid 0): ok.

  Total space 1, 5 to, free space 200 GB.

  I tried with the web service "access to my files"... and then, I throw a shout!

  I got an error, something like 'Path of ACCESS not FOUND' (previously I had two /DISK and /PUBLIC_DISK actions)

  Then I tried again with FTP (same error)

  Then I launched "Scandisk" (still within the management interface) in the newspaper I see "scandisk has failed."

  I tried to launch it again and after one hour, the unit was not responding.

  Is there a way to access the ext3 FS without the web interface?

  How can I make fschk?

  I need to recover the data

  I have lots of photos & videos of my babies when they are born, working documents, working source code

  Any tips?

  What can I do?

  (Material) discs seem to be ok.

  The raid goes to the top.

  The file system appears to be damaged but not bad (or I don't know disk space / free)...

  If the disk file system are not accessible through NAS200 can I connect the disks in a PC with linux and a raid controller? Or is the only raid array works with the controller in NAS200?

  Please help me.

  Thank you in advance.

  The RAID is a software RAID using mdadm. If you have a Linux system, it should be easy to mount hard drives SATA or eSATA or (at most) a USB to SATA converter. If you define for the journaled file system, the NAS200 uses XFS. It uses ext2 for not journaled.

  If you connect the disks on a Linux machine, you will find 3 partitions on each disk: (1) the data partition, (2) a configuration partition, and (3) a swap partition. I do not recommend making any changes to the configuration partition unless you know what you're doing.

  Connect the drive on a Linux system is going to allow you to recover things MUCH faster that to do with the NAS200 (who is actually a PC 133 headless of 486 MHz which feels like it is clocked at 100 MHz).

  If you insist to leave readers in the NAS and you wish to SSH or Telnet access, you can install my firmware . It will not affect your configuration or your hard drives, it will always be like the Linksys firmware (I only added additional features and didn't touch any of the Linksys stuff) and you can easily put the original firmware if you don't like it or don't need more.

  There is no telnet or SSH access in the default firmware.

  = Jac

• Telnet on a X 1018

  Hello

  I'm having a problem with a switch in series X, a 1018. As part of our security policy, that I need to disable telnet, howevre it seems I can disable only SSH and HTTPS, that seems a bit backwards.

  Can someone tell me if and how I can disable telnet access?

  Thanks in advance

  With the series X-series, there is not a method of disabling just telnet. You must use access profiles to limit access. You can learn more on this topic on page 109 of the user guide.

  http://Dell.to/1NSYeYk

  I also put in place a few steps how to do here.

  http://bit.LY/21fmaNa

  I would like to know if you find this useful.

• Telnet or SSH to AP 1142

  Hello

  I am trying to connect to an access point to distance within our network... is it possible to activate telnet or ssh access point by WCS or https. Please let me know

  Knockaert

  WCS, you could push a model AP.  On the 'the AP settings' tab, you can enable ssh and telnet access and then apply it to the AP.

  http://www.Cisco.com/en/us/partner/docs/wireless/WCS/6.0/Configuration/Guide/6_0temp.html#wp1064409

• How can I disable telnet on AIR-AP1242AG-E-K9?

  I activated the SSH with user name and password, but I noticed that when I type a username he accepts, as I have to disable the telnet, while I am using SSH

  Configure these commands in your AP

  !

  block-telnet extended IP access list

  permit tcp any any telnet neq

  !

  line vty 0 4

  block telnet access class in

  !

  Ragards