Telnet or SSH to AP 1142

Similar Questions

• WAP561 To Telnet and SSH

  Hello

  We have two WAP561 devices and they delivered with firmware 1.0.3.4. In this firmware release notes, there is open opposition with reference number CSCty22825, declaring that telnet and ssh is disabled in the interface chart and SNMP. In the notes of the other releases, as 1.1.0.4, this caveat is no longer present. We have improved our 1.1.0.4 devices, over telnet and ssh section is still not present in the GUI.

  Is there a way to enable ssh on these devices? In the administration guide, there should be a section called 'Telnet and SSH', but it is not present in the GUI. We also checked with the emulators with different firmwares. Still no telnet and ssh, section.

  Your help is very appreciated.

  Thank you

  Hello

  These options were available in a very old firmware (the first version) which is no longer present on the cisco.com site and unfortunately I do not have. For security reasons, these options have been removed the new firmwares available.

  I hope that the information provided was useful.

  If you have any other questions do not hesitate to contact me.

  Best regards

• Telnet and SSH on PIX515E does not

  I have two PIX515E (primary and Fail-over) and I can't access it via telnet or SSH.

  I can access only once they have restarted and then they react to me and close the connection.

  the version of the show from the primary is as below:

  Cisco PIX Security Appliance Software Version 8.0 (3)

  Version 6.1 Device Manager (1)

  Updated Wednesday 6 November 07 19:50 by manufacturers

  System image file is "flash: / pix803.bin.

  The configuration file to the startup was "startup-config '.

  Primary up to 3 days 19 hours

  up to 13 hours and 18 minutes failover cluster

  Material: PIX-515E, 128 MB RAM, Pentium II 433 MHz processor

  Flash E28F128J3 @ 0xfff00000, 16 MB

  BIOS Flash AM29F400B @ 0xfffd8000, 32 KB

  Hardware encryption device: VAC + (Crypto5823 revision 0 x 1)

  0: Ext: Ethernet0: the address is 0019.e762.f577, irq 10

  1: Ext: Ethernet1: the address is 0019.e762.f578, irq 11

  The devices allowed for this platform:

  The maximum physical Interfaces: 6

  VLAN maximum: 25

  Internal hosts: unlimited

  Failover: Active/active

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Security contexts: 2

  GTP/GPRS: disabled

  VPN peers: unlimited

  This platform includes an unrestricted license (UR).

  Serial number: 810417710

  Activation key running: 0x7785a916 0x349cafef 0x49afea88 0x8bbd3f92

  Modified configuration of enable_15 to 12:49:25.499 EEDT Sunday, July 26, 2009

  can someone help me solve this problem please.

  I would upgrade to 8.2. I don't have the bug number, but you should be able to find it in the Bug Toolkit.

• Telnet and SSH

  Is it possible to have a different public IP (i.e. 66.102.7.000) address to telnet and SSH for the ASA 5510 remotely?  If it is possible, how you would install the telnet and SSH?  The config is attached.  Thank you.

  Laura

  laurabolda wrote:
  Thanks for your prompt response, Jon.
  For clarification, if my computer IP address is 66.102.7.10, can I SSH to the ASA (outside interface 109.66.25.80)? If I can, how would you set it up on the ASA?  Is it the same command as your previous response?
  Thanks.
  Laura
  

  Yes Laura he would be-

  SSH outside 66.102.7.10 255.255.255.255

  Jon

• Information about TelNet and SSH

  Hi all... IM new here

  Its my first qstion

  Q: I would like to know more about TelNet and SSH... How... can its work you explain this...?

  Hi Muhammed,

  Welcome to the Microsoft forums.

  I understand that you need to know about TelNet and SSH. I'll help you with the information.

  The Telnet utility to connect to other computers over a local network or on the Internet. Unlike a modern Web browser, Telnet uses only the controls text to interact through the network. While this method is a little outdated, it is still used by advanced users to test a network or perform maintenance on the system. Telnet is included with Windows 8, but is disabled by default. You can use the control panel to activate Telnet and then perform the network with application basic commands.

  a. open Control Panel. This can be done through charms, Windows + X, or by conducting a search on the start screen.

  b. Select programs from the main menu.

  c. click on or turn off Windows features turn on and approve the application administrative.

  d. check the Telnet Client and Telnet Server (depending on what you need).

  e. click OK.

  You can see the following TechNet article to learn more about TelNet.

  http://TechNet.Microsoft.com/en-us/library/cc732339 (v = ws.10) .aspx

  SSH (Secure Shell) allows you securely transfer files between computers on a network. All the data involved in the SSH session is encrypted in order to protect against hackers. Once SSH is installed on your computers and servers, you can create passwords for individual users, using programs included in the installation of SSH. If you need to SSH to a remote computer, you need to download a third-party program to connect via SSH.

  I hope this helps.

  Please report if the problem persists and we will be happy to help you further.

• Disable telnet, enable SSH

  What is the best way to disable telnet on the public (T1) interfaces of my router and enable SSH? Can I do this without setting up access lists?

  Thank you

  Diego

  You can. Type

  'transport input ssh.

  on the line vty 0 4 and it will only accept ssh connections.

  If you add access lists using access-class, it will add another level of security.

  You should also generate a RSA key for the router global configuration using the command mode,

  generate encryption rsa key

  Before you type this command, make sure that the domain name is configured on the router.

  IP - domain name

  HS key mypubkey rsa cryptographic will show you the RSA key that is generated.

  HTH

• Issue of Telnet and SSH on Cisco 3750.

  I turn on Cisco 3750 and everything so I wasn't able to connect in the area. I even changed the source interface and update transport under the VTY lines input method, no luck.

  Can I choose to disable SSH by removing the corresponding lines of configs and RSA keys. And I changed the entry to transport back to Telnet. After the reboot of the switch, I'm still not able to connect despite the fact that the box is accessible.

  Any help?

  Thank you

  Jean-Marie

  Hello

  This should help to confirm the configuration and troubleshooting SSH on your device: -.

  http://www.Cisco.com/c/en/us/support/docs/security-VPN/Secure-Shell-SSH/4145-SSH.html

  I hope this helps.
  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• Discover via telnet/ssh serial numbers

  Hello

  Nowdays when we try to register to our service contracts, Cisco want to know the serial number of the camera as well. We usually don't write that down.

  Is it possible to get these numbers of series through PuTTY via Telnet or SSH?

  Hello

  What version of software on codec?

  I am S/N for camera of xstatus, with TC 4.1.2.

  SystemUnit ProductId: "TANDBERG Codec C20.

  The SystemUnit software Version: "TC4.1.2.257695."

  xsta cam

  * the camera 1 s: true

  * s camera 1 HardwareID: "51000000."

  * 1s camera manufacturer: "TANDBERG".

  * 1s camera model: "PrecisionHDMC 1080 p 4 X.

  * s camera 1 ID of the software: "S01718 - 4.0FINAL [ID:40069] 2011-05-19.

  * SerialNumber 1s camera: "B1AB14D00123."

  * s camera 1 IpAddress:

  * s camera 1 MacAddress:

  * s camera Position Pan 1: 400

  * s camera 1 Position Tilt: 60

  * s camera Position Zoom 1: 0

  * s camera 1 post Focus: 4576

  * s camera 1 capacity Options: 'ptzf '.

  Kind regards

  Dharmmesh

• Telnet/SSH to PIX outside interface

  Hi all

  Is it possible to allow a telnet or ssh connection to a PIX via the external interface? The documentation I have (seems) declare that telnet access via the external interface 'requires' IPSEC - it is not clear if this is a recommendation or a requirement.

  In addition, the documentation indicates that no traffic will be through a PIX if the inside and the outside interface are configured with the same security level - does that mean that no traffic will pass "full stop." or the traffic will pass if the appropriate ACL/ducts are configured?

  Advances in thanks

  You cannot telnet to the external interface, but you can SSH to it:

  http://www.ciscotaccc.com/security/showcase?case=K75783563

  Traffic will be able to pass on the same level of security if you are running a current version (> = 7.0) of the PIX and configure the feature of "permit same-security-traffic inter-interface":

  http://www.Cisco.com/en/us/products/sw/secursw/ps2120/products_configuration_guide_chapter09186a0080450b7c.html#wp1039276

• NAS200 telnet? fsck? Lost + found? Help me please.

  Hello world.

  I NEED to access the NAS200 drives.

  Somehow my file system was broken.

  Yesterday I was copying some files on the device (attached to a dedicated UPS, so no power failure when writing) during the copy (it was long) I tried to delete some files in a different folder.

  The player responded: removal of the files had a life (even if the copy is complete) it took about 40 seconds to delete each file...

  So I decided to cancel the operation and restart the device.

  I pressed the power button, I heard the stop sound and turns off after a while.

  I turned on it once, it happened as usually: leds (power - activity - disk1 and disk2), beeps...

  Then I tried to access my files, but vista gave me a network share could not be found.

  First of all, I ping the device, he was there.

  Then I have connected to the web management, made a successful logon, checked state.

  All right: two recognized discs. Chip Disk1: OK, chip Disk2logical disk K 0 (raid 0): ok.

  Total space 1, 5 to, free space 200 GB.

  I tried with the web service "access to my files"... and then, I throw a shout!

  I got an error, something like 'Path of ACCESS not FOUND' (previously I had two /DISK and /PUBLIC_DISK actions)

  Then I tried again with FTP (same error)

  Then I launched "Scandisk" (still within the management interface) in the newspaper I see "scandisk has failed."

  I tried to launch it again and after one hour, the unit was not responding.

  Is there a way to access the ext3 FS without the web interface?

  How can I make fschk?

  I need to recover the data

  I have lots of photos & videos of my babies when they are born, working documents, working source code

  Any tips?

  What can I do?

  (Material) discs seem to be ok.

  The raid goes to the top.

  The file system appears to be damaged but not bad (or I don't know disk space / free)...

  If the disk file system are not accessible through NAS200 can I connect the disks in a PC with linux and a raid controller? Or is the only raid array works with the controller in NAS200?

  Please help me.

  Thank you in advance.

  The RAID is a software RAID using mdadm. If you have a Linux system, it should be easy to mount hard drives SATA or eSATA or (at most) a USB to SATA converter. If you define for the journaled file system, the NAS200 uses XFS. It uses ext2 for not journaled.

  If you connect the disks on a Linux machine, you will find 3 partitions on each disk: (1) the data partition, (2) a configuration partition, and (3) a swap partition. I do not recommend making any changes to the configuration partition unless you know what you're doing.

  Connect the drive on a Linux system is going to allow you to recover things MUCH faster that to do with the NAS200 (who is actually a PC 133 headless of 486 MHz which feels like it is clocked at 100 MHz).

  If you insist to leave readers in the NAS and you wish to SSH or Telnet access, you can install my firmware . It will not affect your configuration or your hard drives, it will always be like the Linksys firmware (I only added additional features and didn't touch any of the Linksys stuff) and you can easily put the original firmware if you don't like it or don't need more.

  There is no telnet or SSH access in the default firmware.

  = Jac

• Disable Telnet on 3448P Dell PowerConnect switch

  Hi, I switch from telnet to ssh, but I do not see where to disable the telnet service. Any help?

  Thank you

  JP.

  
  

• SSH access to LWAPP Access Point

  Hello

  I have just a question about the access point (in LWAPP) using SSHv2.

  When can I see the beginning of the AP (in my case a 1242AG) the SSHv2 is enabled, but when I try to connect to the AP by SSH, my SSH connection is cancelled immediately.

  My access point is connected to a switch (i.e: Cisco 3560).

  And another question on this topic... Why that I can ping my LWAPP AP when it is connected to a switch and not when it is connected directly to the WLC (in my case a WLC 2106).

  Many thanks and best wishes,

  Jeff,

  4.1 you can actually enable telnet or ssh by using this command:

  config ap ssh enable

  allow config ap telnet

  But you must assign a user name and password by entering:

  config ap ID password all the

• enable the telnet and password

  Or remove them. Hello. My goal is to one or two internal connections on each Cisco device and then allow Radius Authentication for telnet or SSH?

  Is there a simple way to do this on a Cisco device?

  Thank you

  Dwane

  Oh, I see what you mean, use local authentication failure RADIUS! You're almost right.

  AAA authentication login LINE1 group local RADIUS

  line vty 0 4 'or '.

  line vty 0 15

  authentication of connection LINE1

• Low cost intelligent or managed switch with the console interface

  Could someone recommend more low switch cost smart or managed with the interface of the console?

  I only need 4 ports but need to control CLI, telnet, or SSH.

  no downtime

• SRW208G DOWNLOAD startup config

  I try to upload my switch via Telnet or SSH interface configuration data, but cannot make it work. I have confirmed my server TFTP OK works. The switch is running v1.04 firmware. If I leave the field empty file name I get a response of "unknown error." If I try to enter a file name, this isn't because I go I always get "File not found" backwards as if the system tries to download instead of downloading?

  Source file has the value 'startup-config' and 'tftp' destination

  Why won't this work? Y at - it a trick without papers to get it work? I need to access it via Telnet/SSH to automate the backup of the config.

  After a fight, I managed to download the file via the HTTP interface, but only after access to the URL directly instead of by executives. It seems to be serious problems with the Web interface, because it doesn't work at all with Mozilla and barely works with IE v7.

  I finally got to work. You must set a password for the user that you are connected to the switch as, for example "admin". If you leave the empty password according to the default settings, you can not download the data of configuration via Telnet or SSH. That seems a little weird that you can download the config via the Web interface without a password.